Search Documents

By C. M. Moncrief

A bentonite-clay drilling mud when treated with tetrasodium pyroarsenate underwent substantially the same reduction in viscosity and water loss as when treated with the complex phosphates. The complex arsenate showed a slightly higher reversion after heating; the other arsenates showed poor viscosity-reducing properties. Introduction During the past 10 years the chemical control of drilling mud has become of major importance in affecting the successful drilling and working over of wells. The desired properties of drilling mud have been well established, and in obtaining these characteristics there has developed a large market for viscosity-reducing chemicals. Viscosity reduction produced by humic acid, tannic acid, sodium silicate, sodium tannate, Calgon, and the complex phosphates has been described by Loomis, Ford, and Fidiam.l The effects Of treatment with complex phosphates and ammonium PolyPhosPhates on the rheological properties of muds were investigated by Fancher2 and the alkali vanadates have been described by Williams.3 Laboratory Investigations It is the purpose of this paper to point out the effects of arsenates in controlling the viscosity and gelling characteristics of a drilling mud. Viscosities and gel strengths were measured at room temperatures with a Stormer viscosimeter calibrated in centipoises and operated at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester at a pressure of I00 lb. per sq. in. for 30 min. The hydrogen-ion concentration was measured with a glass electrode. The bentonite-clay suspensions were prepared in the laboratory and allowed to age several days before testing. Members of the Arsenic Group in the periodic Table include arsenic, antimony and bismuth, but this investigation was limited to arsenic. Phosphorus also occurs in Group V of the Periodic system and phosphorus and arsenic form many closely related compounds such as pH3 and AsH3, P2O5 and As2O5, H3PO4 and H3AS04 Samples of tetrasodium pyroarsenate were prepared by fusing c.p. disodium arsenate (Na2HA5O4.7H2O). According to Friend,' this re-forms the ortho-arsenate on dissolution in water. Sodium trihydrodiorthoarsenate was prepared as described by Mellor,5 from arsenic pen-toxide as follows: As2O5 + 3H20 -> 2H3AsO4 2H3AS04 + 3NaOH Na3H3(AsO4)2 .3H20 Sodium dihydrogen orthoarsenateWaHz-As04) was obtained by fusing together equivalent quantities of arsenious Oxide and sodium nitrate, dissolving the residue in water and allowing it to crystallize.

Jan 1, 1946

By H. Becke, D. Stolnitz, D. Flatley, W. Kern

Zinc difhsions in gallium arsenide having surface concentrations as low as 5 x 10'' atoms per cu cm have been attained. A multiple-difhsion sequence is employed during which zinc enters the gallium arsenide from a silicon dioxide film in a solid-to-solid diffusion step. The technique is illustrated for the case of a zinc surface concentration of -1 x 1017 atoms per cu cm and a junction depth of 1.2 p. Radiotracer measurements of -0.1-p layers of gallium arsenide are used to delineate the resulting profile. A diffusion coefficient for zinc in pyrolytically deposited silicon dioxide is reported. ZINC is frequently used as an acceptor impurity in gallium arsenide. As examples, p-n junctions are formed using zinc-diffused layers in solar cells, lasers, and varactor diodes. For these purposes surface concentrations of 10'' to over loz0 zinc atoms per cu cm are desired and readily obtained from a vapor source. Diffusion of zinc into gallium arsenide to yield surface concentrations of about 1017 atoms per cu cm, however, is more difficult. For instance, oldstein' reports that large changes in the vapor density of zinc produce only small changes in surface concentration. Such low surface concentrations are necessary in forming the diffused base of a gallium arsenide double-diffused n-p-n transistor in order to obtain an adequate emitter efficiency. An alternative approach to zinc diffusion which can provide reduction in surface concentration of several orders of magnitude is the introduction of the diffusant from a solid source. This can be conveniently accomplished by using oxide films of the type generally employed for selective diffusion masking. Such oxides also serve to prevent the dissociation of the gallium arsenide surface at the high temperatures of diffusion. DIFFUSION PROCEDURE Fig. 1 illustrates the diffusion sequence which is employed for obtaining zinc surface concentrations in the range from 5 x lom to 1 X 10" atoms per cu cm. The description of technique will be given for the instance of -1 x 1017, which is typically utilized in double-diffused gallium arsenide transistor investigations at this laboratory. Tin- or germanium-doped gallium arsenide wafers drawn from crystals grown by horizontal Bridgman or Czochralski techniques are used, with bulk concentrations ranging from 1 to 3 X 10" carrier atoms per cu cm. Each wafer is chemically polished on the (iii) arsenic face using a mixture of five parts concentrated sul-furic acid, one part water, and one part 30 pct hydrogen peroxide at room temperature, followed by rinsing in deionized and quartz-distilled water. Pyrolytic silicon dioxide was chosen as the oxide coating because of the high quality of the films obtainable, the ease of their preparation, and the excellent control over film thickness and uniformity.

Jan 1, 1964

By E. E. McGinley, L. D. Woodworth

DURING the past several years has occurred what, in the light of future events, may aptly be called the rebirth of the acid Bessemer process. The increased attention given to the technical and metallurgical details involved in the production of Bessemer steels has been exceedingly fruitful, and indicates the value of further research and plant development. In times like these, when the steelmaking capacity of the country is operating at a maximum rate to supply materials for the national defense program, it behooves the Bessemer operator not only to strive to increase production but also to maintain a high standard of quality. The opportunity is ripe, it seems, to recapture fields of application once considered the birthright of Bessemer steels, but supplanted in recent years by open-hearth grades. This involves cooperation all along the line, from the blast-furnace operator to the metallurgical contact man and salesman. The metallurgist's part in this program involves the study of the many steelmaking variables and the measures necessary to ensure constancy in the finished product. It is equally important that the knowledge gained be disseminated widely to ensure the wise application of Bessemer steels in new fields. The merits of Bessemer steels for certain work are well understood. The combined properties of good weldability, machinability and stiffness are unique and fully explain the strong entrenchment of Bessemer steels in certain fields; e.g., skelp for small butt-weld conduit, screw steels machined in automatics, and certain tinplate applications. It is the purpose of this paper to review briefly the physical properties of Bessemer steels as contrasted with those of open-hearth steels, to discuss control measures now employed in the making of Bessemer steel, and to consider the advantages derived from the use of these control measures. PHYSICAL PROPERTIES OF BESSEMER VS. OPEN-HEARTH STEELS A number of Bessemer blows and open-hearth heats were tested for tensile strength, ductility and impact strength. The steels selected were confined to sections from ¾ to 1 ¼ -in. diameter, inclusive, and the carbon content covered was sufficient to yield parallel ranges in ultimate strength for the comparison. Other factors, such as the extent of deoxidation of the steel and variations in chemistry, were kept as comparable as possible. Machined test pieces of 0.505-in. diameter with an 8-in. gauge length were pulled. The data obtained are shown in Fig. 1, ultimate strength being plotted against carbon content. This graph shows that for equivalent carbon content Bessemer steel has on the average 15,000 lb. per sq. in. greater tensile strength and, conversely, for the same tensile strength Bessemer steel requires on the average 0.14 per cent less carbon. The average phosphorus content for the Bessemer steel was 0.090 per cent,

Jan 1, 1941

By Joseph J. Yancik, Leonard L. Felts, George B. Clark

LITTLE information has been published concerning the actual or useful amount of energy obtained from explosives when they are used for blasting. To provide more data on this subject, 8-in. neet cement cubes were blasted in a steel plate box and the breakage energy evaluated by comparison with drop crusher results using Rittinger's,1,2 Kick's: and Bond's' theories. Theories by Bond and Wang," Lineau," Hatch,' Roller,' and others0-11 were not considered applicable. Those used in this investigation may be expressed mathematically as follows: Rittinger Theory E = KrS2, pet,—--------------- [1] 40 d1 d0 Kick Theory TV 1 1 E = =K, [S pct. log1/d+ 100 log d0] [2] 40 d1 L. L. FELTS, Junior Member AIME, was formerly a Graduate Assistant, University of Illinois. G. B. CLARK, Member AIME, was formerly Professor of Mining Engineering, University of Illinois, and is now Chairman, Dept. of Mining Engineering, Missouri School of Mines and Metallurgy. J. YANCIK, Junior Member AIME, is a Graduate Assistant, Missouri School of Mines and Metallurgy. This paper, TP 4213A. is revised from a thesis submitted by L. L. Felts in partial fulfillment of the M.S. degree in Mining Engineering, University of Illinois, 1954. Discussion may be sent (2 copies) to AIME before May 31, 1956. Manuscript, Dec. 27, 1954. Bond's Third Theory E = Kb [S pct. log1/d1+ 100 log d0] where E — energy used in breakage, d, = average diameters of screen fractions of broken cement particles, pct, = percent weight of diameter d;, and 2 pct, = 100 pct. The above equations were employed to determine values of Kr, Kk, Kb for particle size distributions similar to those obtained from the blasting curves. These values were in turn used as a means of approximating the specific energy of the blasted material. The efficiency of crushing by blasting was then determined by dividing this specific energy by the maximum available work of the explosive per gram of cement. Knowledge of the failure of solids under static loads is developing very rapidly. Their failure under impact loads has been investigated and reported in the literature only to a limited extent. Theories of failure' hnder static loading include 1) the maximum stress theory, 2) the maximum strain theory, 3) the theory of constant elastic strain, 4) theory of maximum shearing stress, and 5) Mohr's theory of strength. All of these have elements of usefulness in establishing an applicable theory for blasting. For highly strained and compressed material such as that surrounding a detonating charge of high explosive, the Mohr theory and its implications appear to be the

Jan 1, 1957

By Satyajeet Ghosh, Edward F. Glynn

Many of the proposed techniques for calculating the reliability of rock slopes utilize Monte Carlo simulation. Monte Carlo approaches are attractive because they provide means of solving probabilistic problems with deterministic algorithms. One disadvantage shared by all simulation-based stability analyses is that they assume all the random variables are independently distributed. The paper focuses on the independence assumption and examines the effect of correlation on the probability of failure. In particular it considers the influence of possible (albeit hypothetical) correlation between joint attitudes [(8)] and joint friction angles [($)]. The study indicates that neglecting correlation can introduce significant errors into the reliability computations. With a modest positive correlation between [8] and [$] the error can lead to a 100% overestimate of the probability of failure.

Jan 1, 1982

By Noah Fields Drake

This paper is devoted chiefly to the coal-fields of the western part of the province of Chili and the eastern part of the province of Shansi; but the outline of this belt will give some idea of the extension of the coal-fields over northeastern China. This part of China is topographically divided into: (1) the mountainous peninsula of eastern Shantung; (2) the coastal plains, extending W. and SW. from the gulf of Pechili; and (3) the mountains and table-lands N. and W. of the coastal plains. The plains extend N. and W. from the gulf to within from 10 to 25 miles of the Great Wall, while their SW. extension covers western Shantung and reaches W. along the Yellow river almost to the southern boundary of Shansi. A line joining the mapped coal-fields, shown in Fig. 1, almost gives the western boundary of the plains; since these areas lie on the border of the plains—except the Tsê Chou field, which is on the table-land, 20 to 25 miles from that border. The coal-fields which have been mapped and investigated by the author are shown in Fig. 1. The one at and around Tongshan is known as the K'ai-p'ing coal-field; the one W. of Peking has been called the Wang-p'ing coal-basin; the one SW. of Pao-ting and N. of Chêng-ting may be called the Lingshan coal-field; and the one at and around Tsê Chou is known as the Tsê Chou coal-field. I. The K'ai-p'ing Coal-Field. As is shown in Fig. 2, most of this field lies in the coastal plains, and is therefore covered by alluvium and loess, which have buried the older rock-beds, and the more gentle and older topographic outlines, to such an extent that most of the re-

Jan 1, 1902

By Jack M. Swales

Kermac Potash Co., the newest American entry in a rapidly expanding industry, has come on the scene with notable variations in conventional shaft-sinking and mining techniques. Located in the famed potash producing district east of Carlsbad, N. Mex., Kermac started up its mine in November, 1965, to supply ore to the company's 500,000-tpy potash crystallization refinery. In so doing, the company (1) drilled the first large diameter mine shaft in the potash industry and (2) has employed new continuous miners especially adapted for use in thin potash beds. REACHING THE ORE ZONE In its initial mine planning, Kermac, a partnership owned jointly by Kerr-McGee Corp. and the National Farmers Union Development Corp., considered it imperative that the shafts be sunk and equipped as soon as possible and that the mine be developed sufficiently to insure a constant ore feed to the mill when the unit was placed on stream. After examining the alternative sinking techniques available to it, the company decided to accept a proposal by Big Hole Drillers, Inc., to drill the shaft from the surface through various formations of sandstones, siltstone, shales, anhydrite, limestones, dolomite and salts to the potash ore zone.

Jan 12, 1966

This report presents the comments of members of the Institute's Sub-committee on Physics of Mine Ventilation on the proposals of a special committee of the Institute of Mining Engineers (London). This report is as follows: THEORY OF MINE VENTILATION Abstract of a report submitted June 16, 1925, to the Council of The Institution of Mining Engineers by a Special Committee Laws of Flow of Aib The law of flow of air in mine galleries is, at present, expressed by two formulas differing slightly in shape but both derived from the original hydraulic formulas of Chezy and others. These formulas are: The Atlcinson Formula.—Pa = KsV2, which in transformation becomes a3 where P = pressure producing flow; K = coefficient of friction; s = surface of the mine galleries; V = velocity of flow; Q = rate of flow; a = area of mine galleries. This formula is especially applicable to mine galleries, but is unwieldy in application, as in many problems we are dealing with changes produced in the same set of airways when K, s, and a are assumed not to change, and the only variables are P and Q. Great uncertainty prevails as to the exact values to be assigned to the coefficient K in different types of airway, as different workers have given widely differing values. This formula assumes: (I) That resistance to flow is independent of the pressure within the gallery. (2) That changes in volume within the limits of pressure ordinarily met with may be neglected. (3) That changes in density and viscosity and mode of flow of the air may be neglected. (4) That the coefficient K is a constant. (5) That P is proportional to the square of the velocity. We cannot find any reliable experimental work leading us to conclude how far these assumptions are justifiable in mining practice. Equivalent Orifice Formula.—The fundamental form of this formula is Q = ~nA.\/2~11

Jan 1, 1927

By Günter Petzow, Siegfried Steeb

DURING an investigation of the U-Co-A1, U-Ir-A1, and U-Ni-A1 ternary systems, three previously unknown phases have been identified which correspond to the phases UCoA1, UIrA1, and UNiA1, and which be- long to the C22 (Fe2P) type (P 6 2m). In the following the structure determination of the new ternary phases is reported. The alloys have been prepared in an arc furnace under purified argon from 99.97 wt pct U, 99.83 wt pct Co, 99.99 wt pct Al, 99.95 wt pct Ni, and 99.97 wt pct Ir. The pellets obtained were bright and brittle; chemical analyses agreed with the nominal compositions. To obtain equilibrium, the samples were annealed in evacuated quartz capsules at 950°C for 30 hr and then quenched in water. Guinier photographs were processed and evaluated according to a method already described previously.1,2 The hkl's, measured and calculated sin2 6 values, and in the case of UCoAl only calculated and estimated intensities, are given in Tables I to 111. Lattice parameters refined according to the least-squares method and the respective mean-square variations are presented in Table IV. Lattice parameters, especially the c/a ratio, lead to the assumption that the three phases are crystallizing in the C22-type structure. For the calculation of the intensities given in Table I, the atomic positions recently reported by wyckoff3 have been accepted for the C22 (Fe2P) type. The uranium atoms were assumed to be in phosphorus sites; furthermore the scattering amplitudes of the boron atoms have been averaged in the stoichiometric formula UB2 according to atomic percentages; i.e., for these atoms a statistical distribution on the iron sites was assumed. The two smallest distances between a uranium and

Jan 1, 1967

By J. M. W. Mackenzie

A microelectrophoresis technique has been used to measure the zeta potential of quartz over a range of pH and ferric iron concentration. The results have been discussed in terms of the adsorption of ferric cations and ferric hydroxide to the quartz surface. Possible relationships between the experimental results and the flotation of quartz have been examined. The adsorption of multivalent cations at the surface of quartz has been studied by many investigators who have used a variety of experimental techniques ranging from streaming potential 1 to radiometric2 measurements. Two possible mechanisms of cation activation of quartz have emerged from the results of these investigations viz: the adsorption of the cation to the negatively charged quartz surface, followed by adsorption of the collector anion to the adsorbed cation site, or: formation of a cation-collector complex which is then adsorbed to the quartz surface. In many natural and industrial systems one of the most prevalent activating species for quartz is ferric iron, this is especially so in the acid-circuit, anionic flotation of iron ore. The adsorption of ferric iron to the quartz surface is complicated by the ability of ferric iron to form complexes with anions, a phenomena which is of minor importance in one of the most widely studied quartz activation processes, ca ++ activation.* *The pK value for [ca(oH)+]/ [ca2+] [oh-] is 1.46 indicating that the influence of Ca (OH)+ ions will be minor in all but strongly alkaline solutions. In order to obtain a better understanding of quartz activation by ferric iron the zeta potential of quartz in the presence of ferric iron has been measured over a range of pH and ferric iron concentration. EXPERIMENTAL METHODS Materials: Selected samples of "rock clystal" quartz from New England, N.S.W., were ground in a pebble mill, washed for three hours in boiling concentrated hydrochloric acid, washed in hot chromic acid and then washed repeatedly with distilled water until the washing water gave no trace of chloride ion.

Jan 1, 1967

By AIME AIME

A CERTAIN area in the State of Indiana seems to be a breeding place for presidents and near president about eighteen miles southeast of Elwood is the little village of Daleville, and there, on April 9, 1890, John Robert Suman, newly elected President of the A.I.M.E., was born. It was not long before he migrated to California, however, where he went to the Los Angeles High School, then for two years to the University of Southern California, after which he went up to Berkeley

Jan 1, 1940

By Wolfgang Gartner

METALLURGISTS engaged in the pulling of single crystals of germanium and silicon, and their zone purification and zone levelling for transistor and diode production, have found that the lifetimes of minority carriers in low resistivity samples tend to be shorter than in high resistivity material, although equal care is taken in the crystal preparation. In other words, it is more difficult to obtain long lifetimes in single crystals of low resistivity semiconductors. It is the purpose of this note to point out that this phenomenon follows directly from the Hall1 and Shockley-Read' theories of lifetimes in semiconductors." In general, the recombination mechanism may be very complicated,' but experiments seem to indicate that the simple formula2 for the lifetime of excess carriers given by n0 + n3 Pn + P1 T = Tpo,------------------+ Tjpu ----------------------- [ 1 ] nu + pn na+ + Pa is a good representation of the situation prevailing in transistor grade semiconductors. In this formula, no and pa are the equilibrium densities of electrons 6+ - E./ET and holes, n1 = N,e is the number of electrons E1- E2/KT in the conduction band, and p1 - N,e is the number of holes in the valence band, both for the case in which the Fermi level falls at the trap level, E1. N,. is the effective density of states in the conduction band; E1, the recombination level; E1, the lower edge of the conduction band; k, Boltzmann's constant; T, absolute temperature; N,., effective density of states in the valence band; and E,., the upper edge of the valence band. t,.,, denotes the lifetime of holes injected into highly n-type material, and The indicates the lifetime of electrons injected into highly p-type material. Eq. 1 holds for nondegenerate semiconductors in which only one recombination level is active and the charge in the recombination centers is neglected. It is further assumed that the number of injected ex-

Jan 1, 1957

By Edwin T. Wood

THE term blending as used herein refers to the mixing of ores assaying more than 0.20 pct U3O8 with low grade material assaying less than 0.20 pct U3O8. Such blending when properly understood and controlled will produce more total dollars of profit from many mining ventures. The question whether or not to blend is particularly vexing when an orebody is surrounded by an envelope of low grade material or separate tonnages of low grade exist which could be extracted coincident with the higher grade ores. Should any, all or part of this low grade be mined? If so, in what proportion and what is the limiting assay of the low grade material?

Jan 7, 1958

Sept. 3-8, AIME, Fall Meeting, Industrial Minerals, Minerals Beneficiation, Mining, Geology, & Geophysics, Iron and Steel, and Coal Div., Palmer House, Chicago. Sept. 3-13, AIME, Chicago Section, Centennial of Engineering, Chicago. Sept. 5-8, Engineers' Council for Professional Development, annual meeting, Hotel Sheraton, Chicago. Sept. 11-13, American Institute of Chemical Engineers, Palmer House, Chicago, Ill. Sept. 13, Columbia Section, AIME, Canadian Institute of Mining and Metallurgy, joint all-day meeting, Metaline Falls, Wash. Sept. 18, AIME, Utah Section, Newhouse Hotel, Salt Lake City. Sept. 20, Colorado Section, AIME, Denver. Andrew Fletcher, speaker. Sept. 22-25, American Mining Congress, Metal and Nonmetallic Mining Convention and Exposition, public auditorium, Denver. Sept. 23-25, Institution of Mining and Metallurgy, symposium on mineral dressing, Royal School of Mines. London.

Jan 1, 1952

By J. J. Jakosky

The strategic importance of the metallic minerals in our industrial economy, and the declining rates of discovery have focused attention on means of exploration for new mineral deposits. A consideration of exploration techniques leads to an attempt to evaluate the effectiveness of geo- physics as a tool for mining exploration. One means of evaluation will be to compare the use of geophysics in petroleum exploration with its possible uses in mining.

Jan 1, 1949

By John Treweek

FOR many years the Homestake Mining Co. has devoted serious attention to the elimination of accidents, and ground is steadily being gained in this direction. In accident prevention work it is line-plunging with perfect teamwork and not the spectacular forward pass that brings progress toward the goal. In both surface plants and under- ground workings we regard "good housekeeping" as a first requisite for safety as well as efficiency. Under this term are included all types of safety guards and protective devices as well as cleanliness and orderliness it working places. Perhaps the most important factor in safety work is to arouse and maintain employee interest. The general morale and contentment of employees is of particular importance.

Jan 1, 1938

By Earl Ingerson

BORE surfaces of used guns commonly show a pattern of cracks in various degrees of development. It has been suggested that these cracks may aid erosion by providing channelways for the gases, eventually leading to the tearing out of blocks of metal. Under the general studies of gun erosion conducted at the Geophysical Laboratory it appeared desirable to consider this factor, and to determine the resistance to surface cracking offered by gun steel and by various other materials that might be used in the bores of guns. METHOD AND APPARATUS In order to make such a determination it is necessary to have (I) an arrangement in which the surface to be studied can be subjected to conditions similar to those in a gun with respect to temperature, pressure (developed by explosion gases), composition of the gases and length of time the surface is exposed to the gases; and (2) a specimen that can be examined readily after any number of shots, and then fired again, if necessary. The first of these conditions can be met by using an explosion vessel designed by H. S. Roberts of the Geophysical Laboratory. Fig I shows a cross section of the apparatus. The "gun" G from which the charge is fired is made from the receiver of a caliber 0.30 army rifle, M1903, and the charges are prepared in caliber 0.30 cartridge cases. The test specimen S is held in place by a cone-shaped plug P and by a steel ,bridge B which is bolted to the outside of the explosion vessel on either side of the section shown. The plug, in turn, is held in place by a screw collar C. Maximum pressure is controlled by a brass rupture disk R. Part of the explosion gases flow past the two flat areas on S. st the two flat areas on S. Temperature and composition of gases, and the time before the rupture disk breaks, can be controlled by amount and kind of powder used, and pressure can be controlled by using rupture disks of different thickness. While the explosion vessel used was not designed so that temperature and pressure could be measured, in other vessels of closely similar size and shape containing proportionate charges of the same kind of powder as that used for standard testing procedure, values of 2700°K and 5000 psi were obtained. Since the orifices past the flat areas on the plug are small compared to the rupture disk hole (1:16), most of the gas goes out through the rupture disk when it breaks. The amount that goes by the plug depends on (I) the pressure attained before the rupture disk breaks and (2) the time it takes for this pressure to be built UP. The second condition (examination at will after any firing) is met by using for specimens short rods that have flat areas ground on opposite sides. These flat

Jan 1, 1947

By D. T. MacRoberts

A simple disturbance in a gas reservoir travels with a finite velocity which is nearly independent of the amplitude of the disturbance. As a result very complex transients may be set up which seriously affect observation at a well. The time of transient is much longer than commonly supposed. INTRODUCTION A change in pressure at a gas well is not propagated through the reservoir instantaneously but with a definite fin- ite velocity. Knowledge of the period ! of this transient is of value because: 1. Observations of pressure and flow-rate during the transient may affect interpretation of back-pressure tests. 2. Interference effects between wells may be used to determine continuity of formation. 3. Additional information concerning the physical characteris- tics may possibly be deduced from the behavior of a well during the transient. MATHEMATICAL DEVELOPMENT It will be assumed that the well is initially closed in and that the pressure is constant throlughout the reservoir. As the initial disturbance passes outward from the well it is further assumed that a logarithmic pressure distribution is established between the most distant point reached and the well, so that: <l> = ((/)r-<t>w) I ------------ + (/) . (1) Manuscript received at office of the Branch September 15. 1948. Paper presented at Branch Fall Meeting, Dallas. Texas. Oct. 4-6, 1948. r. = distance to any point between r and rw r = radius of drainge iw= radius of well (/) = potential (P for incompressible fluids, P2 for perfect gases) Up to the time the effect reaches the point r the production from the well will be: W= (Pr-P,,,) . (2) i b W = volume produced t = sand thickness F = fractional porosity Pr = reservoir pressure Pm = average pressure between r and rw Pb = atmospheric Pressure All pressures will subsequently be stated in atmospheres and the constant Pb will be omitted. This will be produced at a rate: dw t k (Pr³-PW2) do d 0 - . (3) log — Pw = pressure at the well k = permeability 0 = time = viscosity

Jan 1, 1949

By D. T. MacRoberts

A simple disturbance in a gas reservoir travels with a finite velocity which is nearly independent of the amplitude of the disturbance. As a result very complex transients may be set up which seriously affect observation at a well. The time of transient is much longer than commonly supposed. INTRODUCTION A change in pressure at a gas well is not propagated through the reservoir instantaneously but with a definite fin- ite velocity. Knowledge of the period ! of this transient is of value because: 1. Observations of pressure and flow-rate during the transient may affect interpretation of back-pressure tests. 2. Interference effects between wells may be used to determine continuity of formation. 3. Additional information concerning the physical characteris- tics may possibly be deduced from the behavior of a well during the transient. MATHEMATICAL DEVELOPMENT It will be assumed that the well is initially closed in and that the pressure is constant throlughout the reservoir. As the initial disturbance passes outward from the well it is further assumed that a logarithmic pressure distribution is established between the most distant point reached and the well, so that: <l> = ((/)r-<t>w) I ------------ + (/) . (1) Manuscript received at office of the Branch September 15. 1948. Paper presented at Branch Fall Meeting, Dallas. Texas. Oct. 4-6, 1948. r. = distance to any point between r and rw r = radius of drainge iw= radius of well (/) = potential (P for incompressible fluids, P2 for perfect gases) Up to the time the effect reaches the point r the production from the well will be: W= (Pr-P,,,) . (2) i b W = volume produced t = sand thickness F = fractional porosity Pr = reservoir pressure Pm = average pressure between r and rw Pb = atmospheric Pressure All pressures will subsequently be stated in atmospheres and the constant Pb will be omitted. This will be produced at a rate: dw t k (Pr³-PW2) do d 0 - . (3) log — Pw = pressure at the well k = permeability 0 = time = viscosity

Jan 1, 1949

By Maurice Ewing, L. Don Leet

The most important quantitative method in seismic prospecting by refraction shooting is the method of profiles. A profile is established by firing a series of charges at various points along a straight line which terminates at the seismograph. The same data are obtained by repeatedly firing charges at one place and recording at a series of stations along the line of the profile. The quantities which are measured are the distance x from each firing position to the seismograph and the time t required for the first disturbance from each explosion to travel to the seismograph. These data are used in plotting the familiar time-distance graph. The only time-distance graphs that will be considered here are those obtained in localities where the velocity of propagation depends solely on the depth beneath the surface; that is, where there is no slope in the subsurface. The essential calculation to be made from such a time-distance graph is the determination of P(x), the maximum depth of penetration of a disturbance coming to the seismograph from a firing point at the distance x from the instrument. If the time-distance graph consists of a series of straight lines, as is often the case, the penetration P(x) can be calculated by means of formulas which appear in almost every description of seismic prospecting.&apos; Until the present, however, the only formula that has been available for calculating P(x) for time-distance graphs which are smooth curves is one which requires an arbitrary assumption regarding the law of velocity increase with depth.2 The practice in these cases has been to approximate the curve by means of a number of straight lines and then to apply the ordinary straight-line formulas. This method clearly can yield accurate results only when a sufficiently large number of straight lines is used. The labor of computation increases rapidly when the number of lines is increased, so too few lines often are used. Further than that, there is a strong tendency to overlook the approximate nature

Jan 1, 1932