Search Documents

By A. S. Michaels, R. S. Timmins

A study of the effect upon oil recovery from an un-consolidated porous medium of chromatographic transport of selected reverse-wetting additives during water displacement is described. Flow tests were performed on hydrocarbon oil-saturated sand columns (containing connate water) into which small volumes of short-chain aliphatic amine solutions were introduced during water flooding. Concurrently, meusurements of oil-silica contact angles, oil-water interfacial tensions and oil-water distribution coefficients were measured us a function of additive concentration. Certain treatments were found to cause a slight reduction in oil recovery, while others produced a significant increase (up to 50 per cent of the normtzl irreducible rninimum oil saturation). Recovery eficiency was correlated most satisfactorily with the maximum degree of reverse wetting produced during additive transport; conditions which resulted in only mild oil wettability of the sand reduced recovery, while those favoring strong oil wetting increased recovery. A mechanism of reverse-wetting additive action during chromatographic transport is developed which ascribes the results to transient changes in oil-solid contact angle during flow, with consequent release of oil trapped by capillary forces. Implications of these observations with regard to improved waterflood efficiencies are discussed. INTRODUCTION The need for finding improved methods of oil production is amply illustrated by the large volume of oil considered economically unrecoverable by existing production practice. Water flooding has long been an excellent method of secondary recovery. However, even in those areas of a formation which are well swept by a water flood, 20 per cent or more of the oil remains trapped within the formation and is not recovered. This trapping of oil within the pores of the rock structure results primarily from interfacial forces. If these interfacial forces were altered, it is possible that the trapped oil could be released and recovered. The addition of surface-active agents to a water flood to alter the interfacial properties of the oil-water-solid system has received considerable attention as a method of increasing oil recovery. Studies of surfactant treatment have yielded varied and, in some cases, apparently conflicting results. Increased oil recovery using surface-active agents has been reported by a number of investigators. Others have found that use of surfactants in a water flood either has no effect upon oil recovery or decreases it. Since surface-active agents tend to alter the formation wettability and oil-water interfacial tension simultaneously, several investigators have tried to determine the role these two factors play in oil recovery. Data have been presented which indicate that the most desirable condition for the solid surface is strongly water-wet. Other results indicate that, although breakthrough recovery may be less, the greatest ultimate recovery is obtained when neutral wettability prevails.", " The desirability of low interfacial tension seems to depend upon the wettability of the formation. Reports of higher recoveries, when the interfacial tension is high in a water-wet system and low in an oil-wet system, are at odds with reports of increased recovery in water-wet systems when surfactants which decrease the interfacial tension are added to the water flood. A review of previous work studying the effects of using surface-active agents in a water flood shows that these agents produce widely different effects and that opinions as to the role of the various interfacial properties are diverse. The consensus, however, is that the interfacial properties are quite important in the displacement of oil from a porous medium by water. Even in those investigations where appreciable increases in oil recovery resulted from treatment with a surface-active agent, economic considerations generally made practical application of the treatment unattractive because surfactants tend to be adsorbed within the formation. This adsorption would necessitate using large quantities of surfactant if all of the flood water were treated to contain a given surfactant concentration, even if this concentration were quite low. Preston and Calhoun suggested that the principles of chromatography could be applied to the use of surface-active agents as a means of increasing oil recovery. A small volume of surface-active material is injec-

By H. Conrad, E. Stofel

The fracture behavior of 60-deg-oriented sapphire crystals was investigated for both tension and compression. Plastic flow on the basal plane was found to be a factor in reducing the tensile stress required to produce fracture in the temperature RECENT experiments1-' have shown that single crystals of a alumina (sapphire) can deform plastically, particularly at temperatures greater than 1000°C. The effect of this plastic flow on the fracture behavior of sapphire was not established, but range 1100º to 1500ºC. Mechanical twins, both (0001) and (0111) types, were produced by compression in the temperature range 1100" to 1300°C. Cracks propagated more readily along the twin boundaries than in the nontwinned crystal. experiments with other ceramic crystals4'5 have shown that plastic flow can initiate cracks that lead to catastrophic failure. This suggests by analogy that plastic flow might also be an important factor in the fracture of sapphire crystals. A recent experimental investigationS undertaken to determine the mechanism of plastic flow in sapphire provided an opportunity to study the type of fracture produced after various amounts of plastic shear strain. The results of this study of fracture are reported in the present paper. During the course of

Jan 1, 1963

By D. J. Weintritt, J. C. Cowan

Methods of studying oilfield mineral .scale deposition in the laboratory do not work for barium sulfate because only small nonadhering crystals ore formed. On the other hand, barium sulfate scale found in down-hole or surface equipment is strongly adhering and may contain very large crystals. Results suggest that most of the difference derives from the extremely low .solubility of barium sulfate. Firm adherence of scale and the consistent development of oriented crystals 100 microns and larger suggest a relationship between scale adherence and crysta1 growth. Data from this study indicate some reasons for barium sulfate's occurring as a deposit in oilfield waters. The unique characteristics as well as the associative properties of barium sulfate scale as related to calcium carbonate and calcium sulfate ere shown. INTRODUCTION The first observed deposition of barium sulfate scale in oilfield production equipment is unknown but probably coincides closely with the beginnings of the oil industry itself. Moore' described barite oolites in some producing wells in the Saratoga field, Tex., in 1914. Currently, positive identification of barium sulfate deposition is recorded in most of the major oil-producing areas of the United States. As efforts continue to identify the composition and functions of the materials found in scale deposits, the geographic and economic importance of the part played by barium sulfate will become even more important. This belief is based on the following Facts. 1. Many oil fields in the U.S. are in or entering their mature phase and the volume of produced water is increasing; thus, the cumulative effects of low-solubility minerals become more significant. 2. Secondary recovery techniques and increased emphasis on waste disposal systems require controlling the behavior of all constituents of water to prevent formation plugging. 3. The more general use of instrumental analysis has reduced the time and improved the accuracy of complete scale and water analysis. 4. Once formed, barium sulfate scale is resistant to present methods of chemical removal; therefore, costly mechanical methods are necessary. Thus, new methods of prevention and control will require specialized chemical techniques and better knowledge of the causes of scaling. Consider the results of some simulated field deposition studies illustrating this need (Fig. 1). The studies utilized a Scale Deposition Test Cell* and each coupon was exposed to 8,000 ml of a 300 me/liter solution of the various types of mineral scale. All tests were conducted at 140F. Only the calcium sulfate and calcium carbonate deposited scale. The solution containing 300 me/liter of barium sulfate exhibited copious amounts of precipitate, but none of the precipitate adhered. The fluids from the effluents were also allowed to impinge on glass slides. Fig. 1 shows the relative adherence of the three types of scale on unetched glass. The barium sulfate failed to deposit in the same manner as the calcium carbonate and calcium sulfate solutions.

By Charles N. Bell

The Telluride mining district of southwestern Colorado is defined by the 37" 45' and 38" parallels of latitude and 107" 45' and 108" meridians of longitude. Telluride was never a boom camp, but has had a steady growth. In recent years, notwithstanding the business depression of 1920, the business has been the same as in normal years. The first prospector is said to have appeared in 1875, in which year locations on the Smuggler vein were made. Shipments were made in 1877 and 1878, and in 1879 milling the ores was attempted. While the district produced high-grade ores, it did not become important until 1890, when the Rio Grande Southern R. R. was completed from Ridgway to Telluride. The railroad has since been extended to Durango. In the fall of 1896, 400 stamps were in operation, and the annual production was $3,000,000.00, two-thirds of which was gold. The total production from 1875 to 1923 was: gold $58,274,527; silver 41,-830,920 oz., valued at $31,016,893; copper 15,258,866 lb., valued at $2,533,291; lead 166,056,484 Ib., valued at $8,324,910; zinc 18,141,182 Ib. valued at $1,323,787; or a total production of $101,473,408. All claims are held in fee. Most of them are 1500 by 300 ft. but claims located within the last few years are 1500 by 600 ft. General supplies are obtained at Telluride, Denver, and Salt Lake. The largest mines are within 6 miles of the town of Telluride. Denver is 422 miles and Salt Lake is 439 miles, by rail, from Telluride. One-half of the distance to Denver and one-sixth of the distance from Telluride to Salt Lake is by narrow-gage railroad. The labor is efficient. The best miners are Italians and Austrians, then Slavs, Greeks, and Mexicans follow in the order mentioned. There are no labor unions. There are no serious mine pumping problems, the drainage being through adits. The Tomboy and Smuggler companies pump water from their reservoirs, the former for milling and domestic purposes and the latter for milling, power, and domestic purposes. BIBLIOGRAPHY A partial bibliography of the Telluride District is: Geologic Atlas Telluride No. 57; Preliminary Report on the Mining Industries of the

Jan 1, 1925

By E. M. Wise

THe properties required of gold alloys for jewelry are not well standardized, due in part to problems peculiar to certain branches of the jewelry industry, in part to the individual preference of the fabricator and to his willingness to cope with certain difficulties in manufacture, which arise with the use of certain alloys. General Requirements In general, the properties desired may be classed as follows: 1. Color should conform to the dictates of good taste and smart style. 2. Corrosion resistance and tarnish resistance should he good. This is to a considerable extent determined by the carat. Resistance to such corrosive agents as mercuric chloride as well as certain depi1atories is unreasonable to expect and difficult to meet. 3. Strength and hardness must be adequate to maintain the delicate contours of finely modeled jewelry. 4. Wear resistance must be great enough to resist abnormal wear, such as is encountered by a wedding ring in a lifetime of wear. 5. Ductility must be sufficient to permit the fabrication of drawn shells, tubes and difficult shapes. Material having a yield point of not less than 60,000 lb. per sq. in., an ultimate strength of 100,000 Ib. per sq. in., and an elongation of 40 per cent. is desirable. 6. Melting point should be between 800" and 1200" C. Colored Golds The popular green and yellow golds are based on the gold-silver-copper alloys; in some cases modified by the introduction of zinc to improve the casting properties and to alter the color, and nickel to increase the strength. The properties of the Au-Ag-Cu system have been the subject of a very thorough investigation by Jänecke,l Sterner-Rainer12 and Carter."

Jan 1, 1929

By E. M. Wise

THe properties required of gold alloys for jewelry are not well standardized, due in part to problems peculiar to certain branches of the jewelry industry, in part to the individual preference of the fabricator and to his willingness to cope with certain difficulties in manufacture, which arise with the use of certain alloys. General Requirements In general, the properties desired may be classed as follows: 1. Color should conform to the dictates of good taste and smart style. 2. Corrosion resistance and tarnish resistance should he good. This is to a considerable extent determined by the carat. Resistance to such corrosive agents as mercuric chloride as well as certain depi1atories is unreasonable to expect and difficult to meet. 3. Strength and hardness must be adequate to maintain the delicate contours of finely modeled jewelry. 4. Wear resistance must be great enough to resist abnormal wear, such as is encountered by a wedding ring in a lifetime of wear. 5. Ductility must be sufficient to permit the fabrication of drawn shells, tubes and difficult shapes. Material having a yield point of not less than 60,000 lb. per sq. in., an ultimate strength of 100,000 Ib. per sq. in., and an elongation of 40 per cent. is desirable. 6. Melting point should be between 800" and 1200" C. Colored Golds The popular green and yellow golds are based on the gold-silver-copper alloys; in some cases modified by the introduction of zinc to improve the casting properties and to alter the color, and nickel to increase the strength. The properties of the Au-Ag-Cu system have been the subject of a very thorough investigation by Jänecke,l Sterner-Rainer12 and Carter."

Jan 1, 1929

United Engineering Trustees, Inc. H. G. MOULTON, 40 A. L. QUENEAU, '38 ALBERT ROBERTS, '39 The Engineering Foundation GEORGE D. BARRON, '40 A. L. QUENEAU, '38 Engineering Societies Library Board H. K. MASTERS, '38' A. B. PARSONS, Ex-officio F. F. SHARPLESS, '37

Jan 1, 1936

By Marcus A. Grossmann

This paper offers for consideration certain somewhat radical modifications in the iron-carbon diagram, these modifications being the result of the presence of notable amounts of alloying elements. When only small amounts of alloys are present, the standard iron-carbon diagram (Fig. 1) can be used with but insignificant changes; when larger amounts of alloys are present, however, it assumes a distinctly altered appearance. No comment is offered for the present except to call attention to the delta area, A4BM, which represents a region of mixtures of austenite and delta iron, just as area A3SP represents mixtures of austenite and alpha iron. Absence of Carbon We may turn at once to the effect of the presence of alloys. It has been found that in the complete absence of carbon, the gamma change will sometimes disappear entirely when sufficient alloying element is

Jan 1, 1927

Jan 1, 1898

By Louis J. Demer, Paul A. Beck

As reported in a previous publication,1 isothermal grain growth in high purity aluminum and in an aluminum alloy with 2 pct magnesium can be adequately described by means of the empirical relation: [ ] or in some cases, by the simpler relation, [ ] Here, D is the average grain size after an annealing period t. The annealing period includes the time for complete recrystallization R, and the time for grain growth [to]. DA is the grain size as recrystallized, n is a parameter depending on the temperature and on the material. The effect of 2 pct magnesium in solid solution was to decrease D, and to increase R, A and n at a given temperature. The present work was undertaken in order to investigate the above listed effects of magnesium in solid solution, as functions of the magnesium content. The work also includes the study of certain anomalous effects observed in the recrystallization and grain growth of the 2 pct magnesium alloy at 350°C. EXPERIMENTAL PROCEDURE The method of producing the ingots used in this work was described in detail1 and need not be reproduced here. The materials used were high purity aluminum, furnished by the Aluminum Co. of America, of lot analysis shown in Table I and magnesium from a high purity distilled stock of magnesium crystals. [ ] Ingots were prepared for a series of binary aluminum-magnesium alloys of increasing alloy content. The numbers used to designate these ingots and their magnesium contents by chemical analysis are given in Table 2. [ ] The analyses showed no difference in composition between the top and the bottom of the ingots. Spectrographic analysis of the ingots for elements other than magnesium showed, within the limits of accuracy of the method, no increase in impurities over the amounts given in the lot analysis for the high purity aluminum in Table I. Careful microscopic study of ingot 21 in the as-cast condition, at magnifications up t0 1500X, revealed a cer-

Jan 1, 1948

By Charles D. Borror, George K. Foster

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. The Ore Body The ore body is a serpentinized peri-dotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur per- pendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber

Jan 1, 1948

By George K. Foster, Charles D. Borror

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. The Ore Body The ore body is a serpentinized peri-dotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur per- pendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber

Jan 1, 1948

By Joshua I. Tracey, Mackenzie Gordon

THE bauxite deposits in central Arkansas were formed by weather¬ing, in early Eocene time, of fresh or kaolinized nepheline syenite above the water table in a subtropical climate of fairly continuous moisture. Four types are recognized: (1) residual bauxite deposits on kaolinized nepheline syenite, (2) residual deposits on kaolin and bauxite detritus, (3) alluvial deposits of sorted pebbles and pisolites of early Wilcox age, and (4) rubble deposits of later Wilcox age. All were invaded by kaolin and siderite during subsequent burial by Eocene sediments. PART I-FIELD RELATIONS OF THE DEPOSITS The Arkansas bauxite region for years has produced about 95 pct of the domestic supply of bauxite of the United States and it contains today reserves of more than 40 million tons-nine tenths of the known domestic reserves. During World War II, the Arkansas bauxite deposits were explored jointly by the U. S. Geological Survey and the U. S. Bureau of Mines. Some 6000 holes were drilled by rotary rigs under contract to the Federal Govern¬ment, which resulted in the discovery and delimiting of approximately 20 million tons of ore in place. Detailed study of the many sections cored through the bauxite, of data from a much greater number of drill holes made available by all the operating companies, and of the extensive mine faces exposed in the strip pits, has yielded valuable geologic information about the origin of the deposits. It is now possible to piece together a paleotopographic picture of the deposits and the now-buried land surface on which they formed. The bauxite region in the center of Arkansas (Fig 1) contains two producing districts: one in Pulaski County, just south of Little Rock, and the other in Saline County, about 15 miles to the southwest. The deposits in both districts are associated with hills of nepheline syenite, bosses of a large batho¬lith that was intruded into Paleozoic rocks and later buried beneath coastal plain sediments deposited during Cenozoic time. The folded Paleozoic rocks are exposed in the northwest half of the state and are covered in the southeast half by the nearly flat-lying coastal plain sediments. The older rocks were intruded by nepheline syenite, probably in Late Cretaceous time, and sub¬sequently were eroded so as to expose the top of the batholith. In Paleocene time, marine limestone and laminated black silty clay of the Midway group were deposited in an advancing sea, and covered all but the most elevated parts of the batholith. Erosion of the islands of nepheline

Jan 1, 1952

THE problem of reaction rates in the open-hearth process is essentially that of trying to form a fairly clear picture of the "chemical mechanisms" in the bath. Quantitative data on reaction rates would perhaps not be of much practical importance even if they were available; however, what few approximate data there are can be used in combination with data given in Chapters 16 and 17 to sketch a picture of the "chemical mechanics" of the open-hearth process that is consistent with essentially all the present available evidence. The result may later be found incorrect in many details but even so it will illustrate certain useful methods for obtaining a clearer understanding of the process. Consistent with the treatment in Chapter 15, but in simpler terms, we may say that chemical reactions in general involve the following elements or steps : 1. The reacting molecules are mixed together in space in such fashion as to favor collisions among them. 2. Units of what is usually an intermediate molecular arrangement called an activated complex are formed at a certain rate, depending on temperature and concentrations. 3. .These activated complex units decompose into the reaction products (this step usually assumed to be so rapid as never to limit the over-all process). 4. In any of these steps, heat energy may have to flow into, or away from, the reaction zone to permit the reaction to proceed. 5. The products of reaction will usually have to move out of the way to permit further reaction. The temperature factor enters mainly through step 2, and its effect is very marked. (What is called temperature is really the mean energy content of all the molecules of the substance involved; at any one temperature a certain proportion of the molecules will have much higher energy content than the mean value.) Various reaction rates measured at around room tem-

Jan 1, 1964

By Chester S. Conrad

SEVERAL years ago Pittsburgh Consolidation Coal Co. intensified efforts to combat the hazard of mine fires. The program consisted of three parts in the order of likely accomplishment: 1) Purchase and installation of newer and more practical fire fighting equipment. 2) Establishment of trained fire fighting teams at every mine plant. 3) A drive to remove the causes of mine fires. Experimentation with alternating current on section equipment is a major development in this part of the program. Use of alternating current to power mining equipment had been recognized as being most practical from the standpoint of safety. A means to re- place the d-c traction motor is all that has delayed complete section mechanization with a-c power.

Jan 1, 1958

By W. R. Crane

THE effect of mining in the red-ore mines of the Birmingham district has been observed for some time, but, except in a few localities, little difficulty has been experienced from disturbance of cover. Cave-ins near the outcrop and fracturing of the surface at greater distances are the most pronounced manifestations of disturbance, while limited areas at points distant from the outcrop and under greater depth of cover have actually subsided. There is no doubt but that in time, because of failure of pillars, extensive fracturing and widespread settlement of the surface will result, particularly along the slope of Red Mountain, where mining has been under way for many years. Were it not that the orebed is overlain by one or more water-bearing formations, the fracturing or settlement of the surface would not be serious; but because of these formations, fracturing of the top rock may in itself be of sufficient importance to warrant the adoption of protective measures. Until development openings and surface plants are transferred to Shades Valley, protection of the surface will probably not be considered imperative, as the area involved is not of particular value for agricultural or building purposes. Further, the collapse of pillars over a wide area may develop squeezes that, if not controlled, may jeopardize the integrity of the mines and necessitate a change in development, from slopes to vertical shafts, at a much earlier period than is now contemplated. The occurrence of heavy beds of strong tough materials at varying distances above the orebed make it doubtful whether any serious disturbance of the surface will be experienced at any considerable distance from the outcrop, although some settlement will probably take place. It is certain, however, that no great volume of water will enter the mines from fracturing of the Fort Payne chert bed, as this is known to be a compact and practically impervious formation beyond the leached zone. Not so much can be said, however, regarding other possible sources of water, as pervious beds and through faults that may be encountered in future mining operations.

Jan 8, 1925

By Henry N. McCarl

[The Construction Materials section contains the following Chapters: Aggregates Cement and Cement Raw Materials Crushed Stone Dimension and Cut Stone Lightweight Aggregates Gypsum and Anhydrite Sand and Gravel Insulating Materials-Thermal and Sound Slag Roofing Granules] Mineral aggregates are those natural and manufactured industrial mineral and rock materials that provide bulk and strength in portland cement concrete, bituminous concrete mixes, and plaster or stucco surfaces. They may also provide special characteristics such as thermal and acoustical insulation, weight, surface textures, abrasion resistance, and impermeability to various concrete products and mixes. Most aggregates are relatively inexpensive materials, but despite their low unit value, the tonnages consumed each year in the United States and throughout the" world make mineral aggregates by far the leading industrial mineral and rock materials both in terms of volume (tonnage) produced and value consumed. The major use of mineral aggregates is in concrete. The low cost, high bulk aggregates tend to keep concrete construction costs at levels competitive with other building materials. Other major uses of aggregates include highway and railroad base or ballast materials, graded fill, and various industrial uses such as metallurgical and chemical fluxes and raw materials-these latter uses are often considered nonaggregate uses of mineral aggregate materials. The per-ton value of mineral aggregate materials at the production plant in 1980 and 1981 varied from $2 to $5 for most sand and gravel and crushed stone, $3 to $6 for air-cooled slag, $7 to $20 for expanded slag and expanded clay or shale aggregate, to as much as $165 to $320 for expanded perlite or vermiculite. The expanded lightweight aggregates have been dramatically affected by increasing fuel costs. It is ironic that the specialized aggregates used as insulating materials to conserve energy cost so much more to produce due to the high proportion of energy consumed in their production. The first four parts of "Construction Materials" deal with the utilization of four major mineral aggregate types: Crushed Stone, Lightweight Aggregates, Sand and Gravel, and Slag. While the focus will be on the use of these industrial minerals and rocks, there will also be some coverage of sources, mining and production, especially in those cases where they are not discussed in the Commodity section of this book.

Jan 1, 1983

By M. C. Young

The Ozark Lead Company operating facilities are located in Reynolds County at the south end of the "New Lead Belt" of southeast Missouri. Development of this wholly owned subsidiary of Kennecott Copper Corporation started in May 1964, with a six foot diameter by 1250 foot deep steel lined shaft. A 20-foot diameter, 1480 foot deep, concrete lined production shaft was collared in March 1968. Production from the facilities began that month and has reached a present average of approximately 6000 tons per day. This paper describes the fully automatic system used to hoist the lead-zinc ore from a depth of 1420 feet to the surface crushing and concentrating facilities, as well as the man and materials hoisting system which allows the lowering of large equipment into the mine. MINING Galena, sphalerite and some copper minerals are found in several mineralized zones of the relatively flat lying dolomite of the "Bonneterre formation". The mineable ore zones vary from 10 feet to 110 feet thick, from 200 feet to 1200 feet wide, and several thousands of feet on strike. Two-boom diesel-hydraulic jumbos equipped with rotary percussion drills are used for both development and production. The jumbos are used principally to open the room and pillar stopes, and a track mounted down hole drill is used to bench in areas where the ore thickness warrants. Explosives used are ANFO, dynamite, and water-jell which are detonated by electric blasting caps. Broken ore (and waste) is hauled by rubber tired transports to chuted transfer raises. Approximately every 500 feet, these raises connect the orebody to the 15 foot by 28 foot train haulage level below. Two twenty ton diesel-hydraulic locomotives haul 160 tons per trip to storage pockets which have a total storage of 1500 tons of material. From these pockets the material is fed over a 6 foot by 20 foot mechanical vibrating feeder which includes one 4 foot by 6 foot grizzly section to a 48 inch by 60 inch jaw crusher. The grizzly and crusher products are transferred horizontally 45 feet on a 48 inch conveyor belt, to one of two 750 ton storage pockets. The material can flow unimpeded into one pocket or be deflected into the second pocket by a movable rock filled hopper. LOADING POCKET The material in each storage pocket is controlled by six lengths of ship anchor chain. The upper end of the 20 foot chain is anchored behind a brow in the pocket, while the lower ends are joined by a header. The lower ends of the chains are raised by two electric powered marine barge winches using 3/4 inch cables. The crusher operator controls the raising and lowering of these chains from a console in the crusher station. The upper and lower travel of the chains is controlled by cams and limit switches on the winch drive. The winches are located within 5 feet of the shaft, and shaft water continually causes problems with the electric components. A malfunction in the upper travel switch will cause the winch to pull the chains into the cable sheave (breaking the cable or sheave), while the lower switch causes the winch to unwind too much rope. Serious consideration is being given to changing the electric motors to pneumatic, since pneumatic motors will eliminate the need of any electrics at the winches. The winches can be "bottomed out" against the sheave without damage to the cable or sheave when raising the chains, and can be allowed to "free wheel" to lower the chains. A surge pocket below the two storage pockets feeds material to two

Jan 1, 1975

By G. O. Hiers

THE object of the experiments reported in this paper is to determine the eutectic composition of copper and tin and to determine the location of the part of the liquidus line immediately above the eutectic composition in copper. Three methods were used in the investigation: (1) the method of dissolving copper in a bath of molten tin at constant temperature, with the idea that when the bath was saturated with copper its copper content, by analysis, together with the temperature at which the saturation took place would locate a point on the liquidus line (2) the method of the differential cooling curves, and (3) the method of microscopic examination. This paper is principally concerned with the results of the last two methods mentioned. The results of the first method, that of dissolving copper in molten tin, did not agree with the .results of Miller,1 by the same method, nor with the results of other investigators by other methods, nor yet with the results of the cooling-¬curve experiments and microscopic examination reported here.

Jan 1, 1929

By James G. Crawford

Correlation Of water with its reservoir zone or formation has been one of the applications of oil-field water analysis of greatest direct value to the petroleum engineer. The water in each producing zone tends to have diagnostic characteristics by which it can be distinguished from every other water above or below that zone in that immediate vicinity. Representative analyses of oil-field waters from producing oil and gas fields in the Rocky Mountain region are included, and the diagnostic characteristics are discussed briefly. It is concluded that the generally dilute nature of Rocky Mountain oilfield waters is a result of dilution by meteoric waters, and that there is no relationship between presence or absence of commercial oil and the character of water in a structure. Introduction The study of waters associated With oil and gas began more than 50 years ago and has been well recognized by operators, engineers, and geologists for about 30 years. It appears unnecessary at this time to recite the history of oil-field water analysis; suffice to say that it has proved its worth many times to the production engineer suddenly confronted with water problems in producing oil and gas wells. Chemists and geologists have studied the possible origin of these waters and as Yet the subject is unsolved in many important phases. There are both local and regional problems connected with the explanation of concentrations and character- istics peculiar to each field, each subsurface zone and each province. Criteria useful in postulating the Occurrence of oil Or gas in One province completely fail when applied to another, and data carefully prepared and analyzed from one field may be actually misleading when applied to another. Correlation of water with its reservoir zone or formation has been one of the applications of oil-field water analysis of greatest direct value to the engineer. The concentrations and characteristics of the waters are essential to the engineers and geologists making interpretations of electric logs in this region. The behavior of water under conditions of reservoir temperature and pressure is dependent to a great degree upon its concentration and characteristics, and thus important to the reservoir engineer. With the advent of secondary recovery methods in the Rocky Mountain region the characteristics and treatment of water will become increasingly important. Premises upon which Correlation Is Based A brief review of the geochemical history of oil-field waters will suffice to present the premises upon which correlations of the waters are based. Sedimentary rocks which are now stratified were first sediments in seas, lakes and streams. These sediments were filled interstitially with connate water. With burial the sediments were compressed arid consolidated, integrated and indurated into bed rock and much of the connate water was dispelled. Following the formation of bed rock the strata were sub-

Jan 1, 1949