Search Documents

At the meeting of the Board of Directors of the Institute on Jan. 26, 1917, the following actions were taken: Messrs. A. C. Clark, Lawrence Addicks and G. D. Van Arsdale were appointed Tellers to count ballots for Officers and Directors. Messrs. T. T. Read, V. S. Harper, and. E. J. Hall were appointed Tellers to count ballots on revised spelling. The Finance Committee's audit for the year 1916 was approved and ordered filed. The Report of the Finance Committee upon the method of raising this Institute's share of the deficit on the additions to the building was approved and accepted. Upon the recommendation of the Secretary, increases in the salaries of some of the employees were approved. The St. Louis Section received an appropriation of $200 for the year 1917. The Columbia Section received an appropriation of $150 for the year 1917. The Montana Section received an appropriation of $100 for the year 1917. The Colorado Section received an appropriation of $175 for the year 1917. The Utah Section received an appropriation of $125 for the year 1917. The Puget Sound Section received a set of Transactions in standard binding. The International Engineering Congress received a loan of $300 until the Congress can realize upon some of its assets.

Jan 3, 1917

By K. K. Landes

The north central and northeastern states supply over 50 pct of the chemical and metallurgical limestone produced annually in the United States, and Ontario is the leading source of this material in Canada. About three fourths of the chemical and metallurgical stone produced in this area comes from Michigan, Pennsylvania, Ohio, and Ontario. The specifications, physical and especially chemical, for chemical and metallurgical stone depend upon the end use, but in general the tolerance for impurities is so low as to rule out most limestones and dolomites. Both high calcium limestone and dolomite are used in the metallurgical and chemical industries. The principal metallurgical use is as a flux in iron ore blast furnaces and open hearth steel furnaces. The major chemical uses are in lime burning and soda-ash manufacture. Other important uses include glass manufacture, in making calcium carbide, and in sugar factories. All deposits of high quality carbonate rock are definitely finite. Invariably and inevitably they diminish in either thickness or quality laterally so as to become unworkable as chemical and metallurgical stone. The size of these high quality lenses ranges from a few thousands of tons to hundreds of millions of tons. The best hunting for new supplies is in the geologic formations known to contain premium quality deposits. However, because of high transportation costs, carbonate rocks, to be workable, must be close to market, dollarwise. Definitions: Chemical stone is limestone or dolomite used as a raw material by the chemical industry. The major chemical uses are in lime burning and soda-ash manufacture. Other important uses include glass manufacture, making calcium carbide, and in sugar factories. The specifications for chemical stone depend entirely upon the end product. Some uses require dolomite, some require high calcium limestone; in a few instances, notably in lime burning, either type of carbonate rock can be used as raw material. As a general rule, a fairly pure stone is necessary and for certain particular uses the tolerance for some elements such as sulfur, iron, and phosphorus may be extremely small. Metallurgical stone is used as a flux in furnace operations, especially in the blast furnace where iron ore is converted into pig iron and in the open hearth furnace where pig iron is made into steel. Either limestone or dolomite can be used in the blast furnace, but only high calcium stone is charged in the open hearth (except for rice-size dolomite used as a refractory). There are no rigid chemical specifications for blast furnace stone, but low silica, alumina, sulfur, and phosphorus are desirable. For open hearth use, in addition to low magnesia, a very low sulfur content is also specified by many furnace operators. For furnace use, fluxstone also must be sufficiently shatter resistant that it will remain in lump form during transport and charging into the furnace. Commercial stone is the term applied in the trade for crushed stone used for roadstone and in concrete aggregate. Many of our best chemical and metallurgical limestones are too soft to qualify in the Los Angeles abrasion test for use as commercial stone. However, some limestones, and a higher proportion of dolomites, do qualify for commercial stone and so can be sold to either market. Place Value: Even the highest grade limestone is still a bulk commodity with a relatively low value per ton. As a matter of fact there is very little difference in the average price per ton between high grade chemical and metallurgical stone and crushed limestone used commercially. Most high quality stone is produced in large operations with consequent low cost per ton whereas most commercial stone is produced in relatively small local quarries. As in the case of other bulk commodities most limestone buyers pay more for transporting the raw material than the cost of the stone at its source. For this reason steel furnaces and chemical plants

Jan 1, 1961

By R. E. Old

Through the use of pressure and production records, formation properties and bottom-hole sample data, the performance of an oil reservoir may be studied analytically to define and evaluate the natural forces acting on and within the reservoir. Use is made of material-halance methods and the equations for natural water encroachment. to estimate reserves. Methods for calculation of pressures are given. A study of the Jones sand, Schuler field, Arkansas, has been made and is given here to illustrate the value of the methods discussed. Introduction With the decreasing rate of discovery of new oil reserves, attention is necessarily focused on the efficient development, evaluation, and production of existing reserves. From the nation's viewpoint, the necessity of conserving resources is obvious. From the operator's viewpoint, the problem is to lengthen the period of profitable operation, in an attempt to increase the return on his investment. To do this the operator must take advantage of the natural forces acting on and within the reservoir. Natural water encroachment, the nemesis of profitable operation in the past, can be and is being harnessed to produce a greater oil recovery during the stage of flowing production. Proper evaluation of water encroachment rates and a fuller under- standing of reservoir behavior dictate the appropriate production procedures. Complacency in hit and miss production is obsolete. Oil production must and will approach the efficiency of other businesses, such as manufacturing. A manufacturer will not place an article on the market until he has fully investigated the processes involved, additional investment in equipment, costs of production, and expected profits. These may be modified by actual experience at a later date, but at least he begins with an idea of expected return. It is just as logical that an oil operator should investigate these same factors during the development and the early period of production of an oil reserve. The complexity of the problems existing in oil reservoirs should not be underestimated. Conversely, they should not be regarded as insoluble. Many completely defy solution, but there are others that can be solved completely or attacked intelligently to yield approximate results. The petroleum engineer has many tools, both figuratively and literally, at his disposal. Physical data such as core analyses, electrical logs, bottom-hole sample analyses, and bottom-hole pressures are accumulated extensively. Advances in the analytics of fluid flow have kept pace with the advances in measurement of physical data. It is the purpose of this paper to show how some of these records may be analyzed to define certain phases of reservoir behavior.

Jan 1, 1943

By R. E. Old

Through the use of pressure and production records, formation properties and bottom-hole sample data, the performance of an oil reservoir may be studied analytically to define and evaluate the natural forces acting on and within the reservoir. Use is made of material-halance methods and the equations for natural water encroachment. to estimate reserves. Methods for calculation of pressures are given. A study of the Jones sand, Schuler field, Arkansas, has been made and is given here to illustrate the value of the methods discussed. Introduction With the decreasing rate of discovery of new oil reserves, attention is necessarily focused on the efficient development, evaluation, and production of existing reserves. From the nation's viewpoint, the necessity of conserving resources is obvious. From the operator's viewpoint, the problem is to lengthen the period of profitable operation, in an attempt to increase the return on his investment. To do this the operator must take advantage of the natural forces acting on and within the reservoir. Natural water encroachment, the nemesis of profitable operation in the past, can be and is being harnessed to produce a greater oil recovery during the stage of flowing production. Proper evaluation of water encroachment rates and a fuller under- standing of reservoir behavior dictate the appropriate production procedures. Complacency in hit and miss production is obsolete. Oil production must and will approach the efficiency of other businesses, such as manufacturing. A manufacturer will not place an article on the market until he has fully investigated the processes involved, additional investment in equipment, costs of production, and expected profits. These may be modified by actual experience at a later date, but at least he begins with an idea of expected return. It is just as logical that an oil operator should investigate these same factors during the development and the early period of production of an oil reserve. The complexity of the problems existing in oil reservoirs should not be underestimated. Conversely, they should not be regarded as insoluble. Many completely defy solution, but there are others that can be solved completely or attacked intelligently to yield approximate results. The petroleum engineer has many tools, both figuratively and literally, at his disposal. Physical data such as core analyses, electrical logs, bottom-hole sample analyses, and bottom-hole pressures are accumulated extensively. Advances in the analytics of fluid flow have kept pace with the advances in measurement of physical data. It is the purpose of this paper to show how some of these records may be analyzed to define certain phases of reservoir behavior.

Jan 1, 1943

By M. J. Pool, P. J. Spencer, R. V. Miner

The partial molar heat of solution of rhodiunz in liquid lin and Rh-Sn alloys has been measured as a function of rhodium concentration at 700" , 725" , 750" , and 775°K. The values at infinite dilution are very exo thermic, ranging from -29,950 to -28,260 cal per g-atom Rh at 700" and 775"K, respectively. At the solubility limit the heat of solution becomes sharply nzore exothermic and has permitted the liquidus boundary to be accurately established at each temperature. From the measurements in the two-phase region of liquid Plus RhSn, the heat of formation of RhSn,has been determined. A large increase in the heat of formation between 725" and 750°K suggests the possibility of a phase transformation in this compound. V ERY few measurements have been made of the heats of solution of transition metals in liquid tin; yet those values that are available are of great interest because of their very large exothermic nature. For example, the heat of solution at infinite dilution of palladium in tin has been measured as about -26,000 cal per g-atom (625" to 800°~),' while the heat of solution at infinite dilution of platinum is even more exothermic at -28,591 cal per g-atom (914°K).' These values are of the same order of magnitude as the heat of formation of many intermetallic compounds and as such clearly indicate that very strong bonding must exist between the solute and tin atoms in the liquid solutions. Rhodium might be expected to display similar solution characteristics in tin in view of its close electronic resemblance to palladium and platinum. Since no thermodynamic data are available for Rh-Sn alloys, rhodium was chosen as an appropriate solute for further investigation of transition-metal systems with highly exothermic heats of solution at infinite dilution. EXPERIMENTAL The heat of solution of rhodium in dilute Rh-Sn liquid solutions was measured as a functlon of rhodium concentration at 700°, 725", 750°, and 775°K. The liquid-metal solution calorimeter used in this work has been fully described elsewhere. At the start of each series of measurements, the solvent bath consisted of about 0.5 g-atoms of 99.9+ pct pure tin. To this was made a number of small rhodium additions, about 0.0005 g-atoms each, and the heat of solution was measured for each. Rhodium of 99.9+ pct purity in powder form was used in order to promote rapid dissolution in the liquid tin. The powder specimens were contained in tin foil stated to be purified (lead-free). This foil was found to have no measurable heat of solution in pure tin so the effect of any impurities could be neglected. The energy equivalent of the calorimeter was experi- mentally determined by dropping tungsten and/or tin specimens at intervals during each series of rhodium drops. The tungsten and tin used were 99.95 and 99.999+ pct pure, respectively. The only heat effect due to a tungsten drop, or a tin drop at low rhodium concentrations in the bath, is the sensible heat of the specimen. The heat content of these materials is well-established and is presented in the compilation of Hultgren et al. 4 As the rhodium concentration in the tin bath increases a small heat effect arises from the reaction: Sn (liquid, T) — & (soln, T) where T is the temperature of the tin bath. Where necessary, this heat of solution of tin was determined by Gibbs-Duhem integration, and corrections were made to the heat effect of the tin calibration specimens and the tin foil containing the rhodium specimens. RESULTS AND DISCUSSION The calculated values of the heat of solution of rhodium in dilute Rh-Sn alloys as a function of composition are shown graphically in Fig. 1. The values have been corrected for the sensible heat of the specimens, initially at 273"K, and apply to the reaction:

Jan 1, 1969

By G. E. Frantti

UNDER the auspices of the Geophysical Committee of Michigan College of Mining and Technology, an investigation was made in Michigan's Upper Peninsula to obtain geophysical data" related to the regional subsurface geology in the area covered by Paleozoic sediments. The area surveyed includes that portion of the Upper Peninsula which lies between R18W to R26W and T41N and T49N, covering approximately 1300 square miles. On the index map, Fig. 1, it is represented by the cross-hatched zone west of Munising. Four of the five sites of detailed investigation are indicated by the letters A, B, C, and D. A detailed gravity and magnetic survey had previously been conducted by J. G. Wilsonz near Perkins, 8 miles north of Rapid River, on a local anomalous area. Results of his work, which showed a large positive magnetic anomaly associated with a gravity anomaly, aroused interest in the possible economic significance of the formations underlying the Paleozoic sediments in this part of the Upper Peninsula. Early in the 1900's the Michigan Geological Survey, as well as many private companies, had done a considerable amount of dip needle work near the southwest corner of the area discussed in this paper. Most of the information available to the writer was obtained from indicated magnetic anomalies on the geological map of the northern peninsula of Michigan. Results of the geophysical activities of mining companies in the vicinity of the Marquette range and Gwinn district were unavailable to the author. Physiography and Geography: The region under consideration has low to moderate relief. About half the area is comprised of swampy lowlands, and because of the swamps and forests much of the land is almost inaccessible. The major drainage system is dendritic, with streams flowing into Lake Michigan on the south and Lake Superior on the north. The general geology, shown in Fig. 2, indicates an overlay of Paleozoic sediments on pre-Cambrian formations along a line running approximately south from Marquette (not shown on the geological map). Actual contact between pre-Cambrian and Paleozoic sediments is not known because most of the area is covered with glacial till, and outcrops are very scarce. Exposures of the Paleozoic sediments show that these beds in the northern areas dip gently under Lake Superior and that in the southern areas they 'dip gently to the southeast. Outcroppings of the pre-Cambrian formations occur primarily to the west of the surveyed area except in the northwest corner where the Laurentian series outcrop as far east as the Gwinn district and also in T46N, R24W. Instrumentation: Gravity measurements were made with the Worden portable gravity meter. Since this was chiefly a reconnaissance regional survey, both the large and small dials were used. The instrument used had a constant of 0.0035 milligals per scale division, a working range of about 25 milligals.

Jan 1, 1957

By B. M. Larsen, J. W. Campbell

Several articles have recently been published discussing the conditions necessary for accurate measurements of temperatures in the open-hearth steel furnace. In the course of a study of refractories service conditions in steel furnaces, the present writers have taken temperatures in several open-hearth shops in the Pittsburgh district. The conclusions, as to conditions necessary for accurate measurements of temperature, are somewhat at variance with those of other investigators. The subject is closely connected both with the close control of steel-making and the prevention of overheating of the silica refractories used in roofs and walls. It is becoming more and more important to obtain furnace temperatures of fairly definitely known accuracy. At present, the most useful instrument for such measurements is the disappearing-filament type of optical pyrometer. This method of measurement has formed the basis of most other discussions on the subject and was also used by the writers. Previous Investigations In 1916, Burgess' made perhaps the first systematic series of measurements in steel furnaces. The emissivity figures of 0.40 for liquid steel and of 0.53 to 0.65 for liquid slags had been determined by the Bureau of Standards and were used by Burgess in this work. These correction factors are still being used and are regarded as fairly accurate, so that the tapping and teeming temperatures on metal streams given by Burgess should be very nearly correct. Most of his temperatures of furnace roofs and slag surfaces were taken while flames were present in the furnaces and include a few roof temperatures above 1700' C. (3100' F.).

Jan 1, 1927

By J. D. Rice, S. C. Pitzer, C. E. Thomas

Interpretation of pressure build-up data obtained in the conventional manner has often been difficult because of the deviation from theoretical behavior. Major causes of this deviation have been attributed to damage and afterflow, and to fluid redistribution in the wellbore which, in extreme cases, can result in a pressure hump in the early portion of the build-up curve. Theoretical investigations show that bottom-hole pressure is definitely influenced by phase redistribution in the tubing column during surface shut-in tests, and that the magnitude of the effect is sensitive to the producing gas-oil ratio and stabilized rate of flow in the well. For field experiments a wire-line tubing packer, which can be run in the tubing against a stabilized flow rate, was developed for bottom-hole shut-in tests. By use of this bottom-hole .shut-in method, pressure humps previously observed in surface shut-in tests were completely eliminated and the effects of afterflow minimized. Analog and digital computer studies have been made to obtain theoretical curves for comparison with field curves, and remarkable agreement between the results of bottom-hole shut-in tests and theoretical curves has been obtained. INTRODUCTION Pressure build-up data from shut-in wells have been used by the petroleum industry to determine the permeability of the formation, to estimate wellbore damage, to evaluate the static reservoir pressure and to speculate reservoir volume. Calculation of these factors is based on methods of analysis developed for theoretical systems whose build-up curves have a charac- teristic shape when the wells are shut-in at the sand faCe.1,2,3,5,8,10 However, field curves obtained by conventional surface shut-in methods do not always exhibit this characteristic. Such factors as stratification, rock heterogeneities and irregular reservoir geometry can cause the character of a build-up curve to deviate from that predicted by theory for a simple system. In addition, all field build-up data are affected by the methods utilized in obtaining the measurements. Conventional surface shut-in techniques allow two effects to occur which contribute directly to the manner in which pressure builds up at the sand face. The first, afterflow, has been recognized for some time and methods are available for estimating the magnitude of its effect and for correcting its influence.' The second, phase segregation in the tubing column after shut-in, has been reported only recently and appears to exert a considerable influence on the character of field build-up curves.!' In extreme cases, phase segregation can produce "pressure humps" in the early portion of the build-up curve. Such curves have been considered anomalous and have defied analysis. It is the purpose of this paper to discuss the effect of phase segregation in the tubing string during build-up and to present a bottom-hole shut-in technique for obtaining field build-up data which minimizes the influence of afterflow and eliminates phase segregation effects. It will be shown that reliable reservoir information can be calculated from build-up measurements obtained using this method, even though conventional surface shut-in tests on the same wells yield anomalous data. DISCUSSION OF PHASE REDISTRIBUTION EFFECTS Some of the effects of phase redistribution on pressure build-up curves have been described previously by Matthews and Stegemeier" who have presented evidence that phase segregation is responsible for the pres-

By D. G. Westlake

Levine has concluded that prismatic slip in titanium is controlled by two distinct thermally activated processes in the temperature ranges O° to 220°K and 220" to 300°K. We feel that his evidence is not convincing. He has drawn a curve through the plot of activation volume u* vs temperature T with a break at 22WK, Fig. 2. We believe that considering the possible experimental error apd the fact that there are only four points between 4° and 196°K, one could be justified to represent these points by the smooth curve we show as a solid line in Fig. 12. Levine believes that (8rf/aT)+ is discontinuous at 220°K, but he hints that he recognizes the possible doubt. We doubt seriously that the results shown in Fig. 1 indicate a discontinuity at 220°K. Certainly if he were justified in drawing a straight line through only four points on Fig. 2, we are even more justified in drawing straight lines through the seven points between 77" and 297°K on Figs. 1 and 3, because a straight line touches all seven of his circles. If his measurements of t were so precise that his decision to draw two curves in Fig. 3 is valid, then the experimental technique is deserving of further mention. We have drawn a smooth curve through the results in Fig. 3 and used this and the curve in Fig. 12 to obtain the values of shown in Fig. 13. Finding continuous is a contradiction of Fig. 4, which deserves comment itself. Levine obtained the solid circles in Fig. 4 using Fig. 2 and a smooth curve through the points shown in Fig. 3. We have replotted these solid circles in Fig. 14. We submit that there is no basis for his two straight lines (dashed in Fig. 14), and therefore have superimposed the curve that we believe is indicated. Certainly, there is reasonable doubt that a discontinuity in dH/dT exists at 220°K, even when one accepts Fig, 2. Furthermore, if one draws the straight lines indicated by least-squares treatments of the results presented as open circles in Fig. 4, their intersection is at about 196°K, not at 220°K as shown. Thus the alleged agreement between Figs. 3 and 4 with respect to "break" temperatures is not apparent. In Fig. 9, Levine has drawn a straight line very much different from the one indicated by a least-squares treatment. Obviously, he has done this because he recognized that H = 0 when T = 0. He is consistent in drawing the low-temperature curves in

Jan 1, 1968

By U. N. Bhrany, N. Arbiter

F. C. Bond (Consulting Engineer, Processing Machin-Dept., AllisChalmers Manufacturing Co., Milwaukee) This is a very comprehensive paper. It deals with 1) size distribution functions, 2) energy-particle size relationships, and 3) criteria for grinding efficiency. The method of analysis used consists of tracing the increase and decrease of successive Tyler scale screen fractions as grinding progresses. The treatment is based upon the assumption that the work done in grinding is concentrated entirely upon the coarse size fractions in the mill. It is postulated that when a feed consisting entirely of particles of one size fraction is batch ground that finer fractions increase at a constant rate as grinding progresses, until finally each in turn begins to be ground and to decrease in amount. It is shown that under these conditions the empirical Gates-Gaudin-Schuhmann log-log size distribution plot can be logically explained. It is difficult to imagine any condition of ball mill operation, or any probability analysis, which would result in no grinding contacts on the finer particles present. However, the authors' postulate must be accepted if their conclusions are to be sustained. They conclude that the equation expressing the for mation rate of each size fraction can be resolved into the G.-G.-S. size distribution equation, and that the curvilinear portion of the log-logsize distribution line represents the only particle sizes which are being ground as well as produced. The author's statement that the G.-G.-S. Eq. 4 applies only to the finer portion of the size distribution while the Rosin-Rammler Eq. 6 applies over the whole size distribution range certainly supports the view that an exponential equation of the Rosin-Rammler type corresponds more closely to actual size distribution than does the power law G.-G.-S. equation. However, the G.-G.-S. equation is used to derive Eq. 8 and Eq. 9, which state that the energy required to grind a ton through a particular mesh varies inversely as the particle size to the exponent -a , whic h is the slope of the extended G.-G.-S straight line. This is stated to apply to both batch and continuous grinding. The G.-G.-S. slope exponent thus becomes very important in all crushing and grinding analyses by this method. The authors include some data which can be used to test their conclusions, as described below: We will consider grinding a feed composed of 14 mesh (1190u) to -200 mesh (74u). The average of 17 Allis-Chalmers grindability tests on quartz gives a work index (Wi) of 12.77. The -200 mesh product should have 80 pct passing 41.6u or P = 41.6. The equivalent 80 pct passing size of the 14 mesh feed particles is considered to be the particle diameter, as is true for spherical particles. Thus F is 1190u. In the work index equation 10 wi 10 wi 127.7 127.7 P f 41.6 1190 = 16.1 kw-hrperton. In Table I the ball mill exponent for quartz is 1.0 and from Eqs. 9 and 10: w=kw-hr/ton =Constan/(do/di) = 16.1 ton so that (1190) Constant/ Constant and the Constant equals 259. The tons per horsepower-hour value is 0.0464, in agreement with Table IV. The exponents for other minerals are listed in Tabl e 11. In Table IIA, the kilowatt hours per ton required to grind these minerals between the same sizes as the quartz, both by the authors' method and the work index equation, are listed. According to the authors kw-hrperton = 259/(16.1)".

Jan 1, 1961

By John R. Eckel

A Iaboratory drilling rig has been devised and placed in operation which permits the application of hydrostatic, terrastatic, and formation pore pressures to a rock sample for drilling under controlled conditions. Calibrated rests of this equipment in-dicate qualitative agreerment with field results on the effect of weight on bit, rotary speed, and rate of circ~~lation on drilling rate. Tests under pressure, using water and air as the drilling fluids, indicate that when drilling saturated limestone samples, a pressure differential between hydrostatic and formation pressure is the only pressure which affects drilling rate. A differential in either direction causes a reduction in rate, but the same diflerential from the wellbore into the formation causes the greater reduction. Also, in lime.stone, air favorably affected drilling rote only when compared to water at high hydrostatic pressurre, all other conditions remaining constant. Large increases in drilling rate with air could be obtained in the laboratory only while drilling a shale, which offered a limited permeability to nitrogen and which could be drilled with a differential from the formation into the wellbore. In general, the magnitude of the changes due to the pressure effect were small compared to changes in drilling rate obtainable by changing either bit weight or rotary speed. INTRODUCTION In the course of Humble's drilling research program, the desirability of investigating several factors which lend themselves to laboratory rather than field study became obvious. Principal reasons for this are the expense involved in field studies and the difficulty of exercising the required degree of control. Of primary importance are investigations of the effect of fluid pressure on rock rate, the effect of pressure on rock drillability, and a study of the fundamental mechanics of rock failure and chip generation. Several years ago some work in the laboratory on the effect of mud properties on drilling rate was re- ported to the API', but the completion of this work and the investigation of the other variables affecting drilling rate required equipment somewhat more elaborate than that used on these earlier tests. This equipment has been assembled to form Humble's Drilling Engineering laboratory. To date only the effect of pressure on rock drillability while using water and air has been investigated, and this work is not yet complete. Facilities are available to investigate the effect of fluid properties on rate of penetration, and information is being assembled on a current basis on the mechanics of drilling. The sequence of presentation in this progress report is somewhat different from that in which the data were obtained since the order of ex-

By Herty, C. H.

No attempt will be made here to review the previous work done by investigators on the general subject of inclusions, because it was discussed sufficiently in an early cooperative bulletin of this series (No. 36, 1928), and reference was then made to general bibliographies. The work described in this present bulletin deals directly with the study of the mechanism of deoxidation of steel with aluminum and the formation of inclusions containing alumina. Unquestion- ably, such inclusions are encountered in most steel-making practices and little has been done to determine their characteristics. Aluminum is used to ensure rapid deoxidation during the solidification stages of the steel. For this reason the possibilities of inclusion elimination are slight and alumina-containing particles will undoubtedly be present in the ingot. Besides this common practice, aluminum is often used in the ladle with other deoxidizing agents such as silicon and manganese. Ladle additions of aluminum are made to rimming steels to obtain the correct partial deoxidation desired in this type of steel. In killed steels the aluminum is added to ensure soundness, as far as blowholes are concerned, in the ingot. In either rimmed or killed steels, alumina or alumina-containing inclusions are found therein, the amount and type depending on the oxidation of the metal, the amount of aluminum added, and the addition of other deoxidizers.

Jan 1, 1957

By James M. Link

Slurry transport of industrial minerals has proven to be practical, economical, and efficient. Industrial minerals currently being pumped for long distances include cement, clay, phosphate, sand, and various waste product from industrial mineral processing operations. This paper will touch upon the basic theory of hydraulic transport of solids and then consider the economic and engineering considerations upon which construction and operation of such a line would be based. Where possible, actual cost data will be presented.

Jan 1, 1974

By T. R. A. Davey

The fundamental principles by which bismuth may be removed from lead by pyrometallurgical processes are enumerated. Qualitative discussion of the phase diagrams concerned is followed by presentation of quantitative diagrams. Brief mention is made of the practical aspects. Data presented show how chemical lead (<0.005 pct Bi) may be produced by the Jollivet, Dittmer, and Kroll-Betterton processes. BISMUTH is an element whose properties are very similar to those of lead, and its minerals are associated to a greater or lesser extent with nearly all the major lead ore deposits of the world. In consequence, the lead produced contains bismuth unless a special debismuthizing process is practiced. There does not appear to be any published comprehensive review of the effect of bismuth as an impurity on the properties of lead, and there is some uncertainty as to the beneficial or detrimental effects of small amounts of bismuth in lead used for particular applications. Standard specifications of most countries stipulate a maximum bismuth content of 0.005 pct for chemical lead. With one exception, this specification is met only by lead producers whose ores are relatively bismuth-free, or whose refineries are electrolytic. In lead for certain applications a higher bismuth content is preferred by some fabricators.&apos; In contrast to the refining for silver, copper, and antimony, the refining for bismuth does not usually result in a large overalil economic gain from the sale of byproduct. Thus, debismuthizing is customarily practiced only if market conditions demand a lead with a bismuth content lower than that produced by classical refining; i.e., softening, desilverizing, and zinc refining. Until this century, debismuthizing was carried out only a:; an incidental result of desilverizing, as later described. This century has seen the development of the Betts electrolytic process—the only successful one of many electrolytic processes proposed and patented —and a number of precipitation processes based on the pioneering work of Kroll,&apos; although only one of these, the Kroll-Better ton process,&apos; is in wide commercial use today. It is proposed in this paper to deal only with the pyrometallurgical processes, excluding those based on aqueous electrolysis. Historical Background Prior to 1833 silver (and incidentally bismuth) could not be removed from lead. To recover silver from rich bullion, the only course available to lead refineries was to cupel the bullion, forming a slag of litharge. The first slag tappings or skimmings, on reduction, yielded soft lead of very low silver and bismuth contents. Intermediate skimmings yielded a lead of somewhat higher silver and bismuth contents, which could if desired be recupelled. The last skimmings yielded a litharge very high in bismuth, which could by successive oxidation and reduction cycles be separated into high purity bismuth, and lead returns. This oxidation reduction process, with modern operating techniques, can still be used today to produce a portion of a lead refinery&apos;s output of very low bismuth content, as discussed later. In 1833 Pattinsone discovered that lead bullion could be purified of silver and bismuth by fractional crystallization, the primary lead crystals formed by partial freezing being purer than the melt. Repeated processing in pans produced a lead containing as little as 0.02 pct Bi. The simple explanation of this

Jan 1, 1957

By A. Mitchell, T. Bagshaw

A recent paper by Thomas1 has presented new data on the solubility of hydrogen in solid silver at 1 atm pressure in the temperature range 600° to 963°C. However, no data is reported in the literature on hydrogen solubility in liquid silver. The Sieverts technique which has been described previously2,3 was used in the present work. Charges of approximately 160 g were melted in Morgan "purox" recrystallized alumina crucibles and purified helium was used for the determination of the "hot volume" during each experiment. A chemical analysis of the silver indicates that the impurity content (Cu + Al) is less than 0.02 wt pct. Hydrogen solubility in the temperature range 963° to 1200°C was investigated. The results of three experiments are shown in Table I. Fig. 1 shows an Arrhenius plot of the present work together with the solid-state data of Thomas, Steacie, and johnson,4 Eichenauer et al.,5 and Siegelin et al.6 The following expression has been derived from the Arrhenius plot of the present data: log (solubility of hydrogen, cm3 per 100 g) = 2.154-3512.0/ToK The heat of solution derived from Fig. 1 is 31,150 cal per g mole H2 compared with the value of 33,020 cal per g mole H2 obtained by Thomas and 12,000 cal per g mole H2 obtained from the data of Steacie. It was observed that hydrogen evolution took place when the silver melts were solidified under 1 atm of hydrogen, which would not be expected from an extrapolation of the results of Steacie. Schenck and Lange7 have observed that, for several transition metals at their melting points, the ratio of the hydrogen solubility in the liquid to that in the solid lies in the range 2.1 to 3.1. The present results and those of Thomas are in accord in this respect having a ratio of 2.8. &apos;C. L. Thomas: Trans. TMS-AIME, 1967 vol. 239, pp. 485-96. 2T. Bagshaw and A. Mitchell: I. Iron Steel Inst., 1966, vol. 204, p. 87. &apos;M. Weinstein and J. F. Elliott: Trans. TWS-AIME, 1963, vol. 227, p. 382. &apos;E. W. R. Steacie and F. M. G. Johnson: Proc. Roy. Soc. (London), Ser. A, 1928, vol. 117, pp. 662-79. &apos;W. Eichenauer et al.: Z. Metallk., 1958, vol. 49, pp. 220-25. 6W. Siegelin et al.: Z. Elektrochem., 1957, vol. 61, pp. 359-66. &apos;H. Schenck and K. W. Lange: Arch Eisenhuettenw., 1966, vol. 37, no. 9, pp. 739-48.

Jan 1, 1969

By T. Sekimoto, T. Kokubo, M. Yamamoto, K. Masuda, T. Moro, H. Sakamoto

The choking-free cyclone was developed primarily to remove solid particles suspended in a slurry containing fibrous materials, such as municipal solid waste. This cyclone is characterized by a screw conveyor at the underflow side of the cyclone. The screw conveyor has a hollow rotational shaft for air supply and is driven by a variable speed motor for discharge control. Even if the underflow discharge is highly concentrated, this type of cyclone can be stably operated without nozzle choking. High classification efficiency similar to that of a conventional cyclone can be obtained as a result of air introduction through the hollow rotational shaft. The recovery of organic matter and the removal efficiency of inorganic matter were actually improved by the application of this cyclone to municipal solid waste. After applying this cyclone to the desliming of fine sand, sand product of low water content was recovered.

Jan 1, 1980

By H. Kazemi, M. S. Seth

The effects of anisotropy and stratification on flow behavior and production performance of oil and gas wells have been studied by numerous authors.1-3 Lefkovits et al.l studied the performance of totally penetrated, stratified bounded reservoirs with no crossflow. Others have studied a similar problem, but with crossflow; Russell and Prats2 have summarized the findings of these papers. Muskat3 studied the steady-state behavior of liquid flow for a partially penetrating well in an anisotropic system and concluded that the productivity weakly depended on the directional permeability ratios (kz/kr>0.1). Nisle4 used the classical method of point source solution to the diffusivity equation to study the effect of partial penetration on pressure buildup of oil wells in an isotropic system. He found that the theoretical pressure buildup curves consisted of two straight lines, the one at early buildup times having a slope proportional to the flow capacity of the open interval (l-d)k, and the other having a slope proportional to the flow capacity of the entire formation hk,. Later Brons and Marting5 supplemented the findings of Nisle and concluded that partial penetration gave rise to a pseudo damage, which reflected itself as a skin factor in pressure buildup calculations. Using the pseudo skin, they calculated the impairment of productivity of the production wells, which agreed well with the results of Muskat.6 Pizzi et al.,? using an electrical analog of a stratified system, concluded that a high pseudo damage resulted if the reservoir was partially penetrated. Harriss studied the optimum spacing and arrangement of perforations in cased holes. Hantush9 derived an expression for pressure distribution in an unbounded reservoir with restricted flow entry. Seth10 extended Hantush&apos;s work to a bounded reservoir. Odehl1 has studied a similar problem for steady-state conditions. The purpose of this work was to investigate: (1) the combined effects of anisotropy, stratification with crossflow, and restricted flow entry on pressure transient analysis of flow and buildup tests, (2) the feasibility of calculating the horizontal permeabilities of intercommunicating stratified systems, and (3) the pressure interference tests in such systems. Theory The partial differential equation governing the isothermal flow of homogeneous fluids of constant compressibility is given by Eq. 1: The initial and the boundary conditions are: 1. The reservoir potential is initially constant, say 4v

Jan 1, 1970

By F. D. Richardson

STAFF: Editor, Gerhard Derge Carnegie lnstitute of Technology Schenley Park Pittsburgh, Pa. 15213 Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Jack H. Scoff, President; Richard C. Cole, Past-President; Harold 0. Emerick, President-Elect; Ralph L. Hennebach, Treasurer; Robert W. Shearman, Secretary; Donald A. Parks, Assistant Secretary; Leslie S. Wilcoxson, Assistant Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: R. E. Lund, Chairman; T. E. Dancy, H. O. Emerick, P. R. Gouwens, R. E. Grace, J. H. Jackson, H. H. Johnson, A. E. Lee, Jr., R. R. Nosh, R. D. Pehlke, and Paul Queneau. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extroctive Metallurgy Division: R. E. Grace, Choirmon; G. M. Bell, D. W. Bridges, J. M. Cigon, G. W. Heoly, T. A. Henrie, R. D. (Holli-doy, C. E. O&apos;Neill, C. S. Somis, A. W. Schlech-ten, and Charles Shull. Iron and Steel Division: R. D. Pehlke, Choirmon; T. P. Floridis, Arnulf Muon, G. R. St. Pierre, E. T. Turkdogan, L. H.Von Vlock, and J. M. Uys. lnstitute of Metals Division: H. H. Johnson, Jr., Chairman; J. B. Clark, Vice Choirmon; M. R. Achter, G. F. Bolling. J. O. Brittoin, G. P. Conard, II, R. S. Davis, L. A. Girifolco, G. T. Hohn, J. P. Hirth, L. Himmel, G.T.horn, George Krauss, J. D. Livingston, R. D. Manning, H. M. Otte, S. V. Rodcliffe, R. E. Reed-Hill, H. C. Rogers, E. ScaIa, O. Sherby, M. T. Simnad, G. R. Speich, E. A. Steigerwald, R. A. Swolin, W. A. Tiller, W. R. Upthegrove, J. B. Wagner, Jr., Derek Wolton, H. W. Weart, W. W. Webb, and D. Published seven times yearly in February, March, April, June, August, October, and December by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street New York, N. Y. 10017. Telephone PLAZA 2 -6800. Subscription $30 per year for non-AtME members m United States and North, South, and Central America; $32, foreign; $7.50 for AlME members Single copies, $6.00, single copier foreign, $6.50. The AiME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1964 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AiME New York Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts. Second dost postaas poid ot New York, N. Y.,ond Ann Arbor, Mich. Volume 230, Number 6.

Jan 1, 1964

By J. F. Shea, O. F. Tangel

Battelle Memorial Institute participated in a program for the General Services Administration aimed at developing a nickel-cobalt separation process that could be integrated in the Nicaro nickel plant. At the time the programwas being carried out, the Nicaro process was a straight-through operation, in which the ore was reduced and leached, after which the pregnant solution was boiled to produce a so-called "bulk precipitate" which contained virtually all of the nickel and cobalt which had been dissolved in the leaching step. The weight ratio of nickel to cobalt in Nicaro ore is approximately 15 to 20:l. The weight ratio of nickel to cobalt in the finished product had to be 100:l or higher to meet specifications. Because the Nicaro process embodied no nickel-cobalt separation step, the only way that a bulk precipitate of the specified nicke1:cobalt ratio could be produced was to so adjust roasting and leaching conditions that nickel would be selectively leached and most of the cobalt would be rejected with the tailings. The required selectivity, however, was achieved at the expense of nickel recovery, which was 5 or more per cent less than might have been obtained with the existing equipment, utilities, man power, etc., had selectivity been no object. The over-all purpose of the program was to develop a separation step that could be fitted into or onto the Nicaro facilities and which would permit the manufacture of a product that would meet the desired specifications and still permit the recovery of a maximum amount of nickel. Battelle suggested that this might be accomplished by reprocessing off-specification bulk precipitate and specifically suggested the process based on ammonium sulphate leaching followed by hydrogen reduction of the leach solution according to techniques developed commercially by Sherritt Gordon Mines Limited. Such a process would not only satisfy the objectives of the research but would present two additional advantages. (1) It would produce a separate cobalt product which could be further processed into metal, alloys, oxides, or salts. (2) It would yield nickel in metallic form which might be more generally marketable and command a slightly higher price per unit of nickel than the Nicaro oxide product. DESCRIPTION OF THE PROCESS Figure 1 is a flowsheet of the process. The essential features are: (1) Extraction of about 97 per cent of the nickel and about 85 per cent of the cobalt from bulk precipitate by a principal leach with ainmonium sulphate solution (Step A). Extraction of virtually all of

Jan 1, 1961

By R. M. Waterstrat

X-ray diffraction and metallographic examination of binary Mn-rich alloys with Ti revealed the presence of intermediate phases in this system. A binary R phase has been identified and also a phase having an a-Mn type structure. The X-ray pattern of the phase TiMn3 is presented and a tentative phase diagram for the Mn-rich portion of this binary system has been constndcted. MANGANESE-rich alloys with titanium have been subjected to thermal analysis at temperatures down to 1100°C by Hellawell and Hume-Rothery.1 Their results indicate the existence of an intermediate phase TiMn3 in this binary system. This phase appears to coexist with the Laves phase TiMn2, and with terminal solid solutions based on the allotropes of manganese, at least down to 1100°C. The above investigators did not attempt to determine the crystal structure of this phase, however. Since, by analogy to the binary systems Mn-V and Mn-Cr3 one might expect to find a phase in this region of the diagram, it seemed desirable to obtain X-ray diffraction patterns of alloys in the concentration range in question, in order to ascertain whether the sigma phase or related structures occur. EXPERIMENTAL PROCEDURES Alloys were prepared by arc-melting electrolytic manganese and iodide titanium in a water-cooled copper crucible under a helium atmosphere. Excess manganese was added to each melt in order to allow for losses incurred during melting. The alloys were then wrapped in molybdenum foil and sealed in evacuated quartz tubes for annealing at various temperatures, as shown in Table I, followed by quenching in cold water. Although the inside of the tubes showed evidence for some loss of manganese from the specimen during annealing, there was no evidence of any reaction between the specimen and either the molybdenum foil or the quartz tube at these temperatures. It was later found that the manganese loss was considerably reduced by annealing these alloys in sealed quartz tubes containing one atmosphere of purified argon. As an added precaution the surface of each specimen was ground off before crushing the alloys to -270 mesh powder, using a hardened steel mortar and pestle. X-ray powder patterns were obtained using either FeKa or CrKa radiation in an asymmetrical focusing camera, which gave excellent dispersion of the closely spaced lines. Pictures were also obtained using a Debye camera of 5-cm radius which provided data in the angular region not covered by the focusing camera. The alloy specimens were polished and examined metallographically, using an etchant consisting of 60 pct glycerine, 20 pct nitric acid, and 20 pct hydrofluoric acid. The 10-g buttons were in each case broken in half and found to be well-melted and free of any gross segregation. One half of certain alloy buttons was submitted to chemical analysis in the "as-cast" condition. No appreciable change in composition seemed to occur during annealing . RESULTS The X-ray pattern of alloy Ti1.17Mn0.83 was found to agree well with that of the ternary R phase which was first found in the Mo-Cr-Co system,&apos; and re-

Jan 1, 1962