Search Documents

By J. L. Tokich, A. R. Troiano

INTRODUCTION SINCE 1921, when Hull' discovered that cobalt can exist in the face-centered cubic and hexagonal close-packed modifications, the transitions that occur in cobalt have been extensively studied. It is generally agreed that on heating the hexagonal lattice changes to the cubic structure at temperatures ranging from 400 to 500°C although considerable doubt exists as to the exact temperature. Data concerning the temperature of the transformation on cooling are much less concordant and their interpretation has not been satisfactory. The study is further complicated by the fact that many investigators have reported the existence of a high temperature allotropic change in the range 850 to 1020°C, at which the cubic lattice reverts to the hexagonal modification. The transition on cooling, which has been reported as occurring at various temperatures from approximately 400 to 100°C, is of particular interest. Troiano and Greninger2 have recently suggested and considered the possibility of allotropic transformations occurring in pure metals by a shear-type, diffusionless (martensite) transformation. The case of cobalt was specifically discussed and certain observations of previous investigators evaluated in terms of this type of transformation. Table 1 briefly outlines the methods and results of previous investigators of the transformation temperatures of cobalt. MATERIALS AND METHODS The major portion of this investigation was performed with cobalt sheet containing a total of 0.2 pct impurities with carbon present to the extent of 0.1 pct. After melting in an induction furnace under an atmosphere of hydrogen, the carbon content analyzed 0.03 pct. Some observations were repeated with hydrogen reduced cobalt compresses analyzing 99.9 pct pure. No significant variations in results were observed employing the as-received sheet, the remelted stock, or the cobalt compresses. Filings for X ray diffraction analysis were sealed in evacuated glass ampoules. Pyrex glass tubing was used for temperatures below 600°C and for higher temperatures clear fused quartz was satisfactory. After appropriate heat treatment at various temperatures, the specimen ampoules were furnace cooled, air cooled or quenched by crushing under distilled water. This allowed a range of cooling velocities from less than one degree C per sec to greater than 1,000°C per sec. X ray diffraction patterns were taken with a Debye camera and filtered characteristic cobalt K-alpha radiation. The proportion of the existing phases was roughly approximated by visual examina-

Jan 1, 1948

Part 1. Coal Part 2. Industrial Minerals

Jan 3, 1977

THIS chapter and the one following deal with the heat quantities involved in open-hearth steelmaking, including the thermal efficiency of the furnace as a generator of high-temperature heat, the heat storage in the steel and slag produced and in the furnace walls, and the heats of the various chemical reactions involved in combustion, in the formation of slag, and the refining of steel. The fundamental laws to be considered are the simplification of the first two ' laws of thermodynamics as applied to problems involving sensible and potential (or latent) heat only 1. Heat input equals heat outflow plus storage. 2. Heat may be transferred only from a hotter body to a colder one. The first of these laws relates to the various heat quantities or the "heat balance" of the process. No one has as yet made an open-hearth heat balance that came out almost exactly balanced, and we assume that the cause lies in the difficulties of accurate temperature and flow-rate measurements at the high temperatures involved and the inherent complexities of flow distribution, air leakage, etc., present in any real, open-hearth furnace system. Some idea of the magnitude of the heat quantities involved can be obtained- by a brief, crude outline of the heat balance of a 90-ton heat of steel. We will assume a 60 to 70 per cent hot-metal charge in a fairly fast working and only moderately efficient furnace, burning fuel oil, with a fuel consumption of around 4 million B.t.u. per net ton. of ingots produced. The time from start of charge to tap is 9 hr. During this period, the oil burned represents 360 million B.t.u., and the sensible heat in the preheated air at the port ends is 117 million B.t.u. so that the total heat input at the ports is 477 million B.t.u. Heat stored in the steel and slag at the end of the heat, plus the various amounts absorbed by certain bath reactions, amounts to a total of 195 million B.t.u., but 120 million of this is supplied by the heat in the hot metal and by various heat--evolving reactions in the bath, so that only 75 million B.t.u. need be supplied to the bath by the flame.

Jan 1, 1944

By J. V. Emmons

It has long been known that the outside skin of tool steel frequently exhibits properties widely different from the interior of the mass.

Jan 1, 1915

NEW MEMBERS The following list comprises the names of those persons who became members during the period Nov. 10 to Dec. 10, 1915: BARTH, ERNEST, Petroleum Geol Box 552, Tulsa, Okla. BEROLZHEIMER, D. D.,.Chemist; Librarian, Barrett Mfg. Co., 17 Battery Pl., New York, N. Y. BLIEK, PIERRE FRANCISCO, Mgr., Compania Minera de Oruro, Oruro, Bolivia, So. Amer. BLOCS, JAMES A., Met 1076 1st Ave., Salt Lake City, Utah. BULKLEY, RALPH G., Mine & Mill Supt.; The Montezuma Mines & Mills Co., Montezuma, Colo. BURRAGE, ALBERT CAMERON, JR., Met. Engr.; Director, 85 Ames Bldg., Boston, Mass. CABELL, CHARLES ARNOLD, Vice-Pres Carbon Coal Co., Carbon, W. Va. CHAPMAN, LEWIS CARL, Economic Geol Producer Oil Co., Houston, Tex. CHOFFEL, FLAVIEN AURELIEN, Mgr Ingersoll-Rand Co., Paris, France COY, HARLEY A., Mine Supt American Zinc Co., Mascot, Tenn. DITTMANN, C. 0. ADOLF, Cons. Engr., Beer, Sondheimer & Co., Inc., Santiago, Chile, So. Amer.

Jan 1, 1916

By P. H. Lindon, J. C. Billington

Fe-O melts containing 0.045 pct 0 were deoxidized with Mn-Si-A1 alloys. Product compositions were reluted to the melt and alloy compositions and were found to be most sensitive to the aluminum content of the alloy. Low residual oxygen contents could be obtained when aluminum oxide was present in the Products because of the reduction of silica and manganese oxide activities. Flotation of the Products from a quiescent melt was followed both by analysis of the oxygen content and metallographic measurement of inclusion concentration. MnO-SiO2-A12O3 products were found to float most rapidly when their composition was such that their viscosity may be expected to be low. Changes in the particle size distribution indicates that particle coalescence occurred and differences in the degree of coalescence are thought to be responsible for the different flotation rates observed between products 0f differing composition. Measured flotation rates were slower than those Predicted from a model based on Stoke's Law, although alumina flotation might be reasonably accounted for by this model. Interfacial effects between oxide particles and the melt are believed to be responsible for the discrepancy. It has been recognized that deoxidation products constitute a large proportion of the nonmetallic inclusions present in killed steel. The amount of oxide inclusions which originate as deoxidation products depends largely upon three factors. These may be summarized, according to P16ckinger1 as: 1) Amount of primary products remaining in the steel prior to cooling. 2) Residual dissolved oxygen content of the steel after deoxidation. 3) Amount of secondary products, formed during cooling and solidification, which remain entrapped in the solid steel. In a well-deoxidized steel containing residual aluminum and/or silicon, the equilibrium dissolved oxygen content is usually very low and so the maximum amount of oxide which may be produced as secondary deoxidation products is small in comparison with the amount of primary products. It may be seen, therefore, that the amount of indigenous nonmetallic inclusions may be minimized if a low dissolved oxygen content is achieved by deoxidation and if the primary deoxidation products are efficiently removed. Oxides which originate by reaction of the metal stream with the atmosphere during teeming are not considered in the present study. It is known that two or more deoxidizers may result in a lower equilibrium oxygen content when used in conjunction with one another than when any of the individual deoxidizers are used alone. Equilibrium studies by Hilty and crafts2 and by Bell3 have shown that manganese increases the effectiveness of silicon as a deoxidizer, and Walsh and Ramachandran4 relate this to a reduction in the activity of silica in the products as the manganese :silicon ratio in the steel increases. It was also shown by Herty's work on deoxidation of steel by silico manganese alloys,5 that there existed an optimum ratio of manganese to silicon which gave a minimum inclusion content. This ratio was in the range 4:l to 7:l and the (FeO-MnO-SiO2) products formed by such deoxidation practice were found to lie in a composition range having very low liquidus temperatures (1170 to 1250°C approx). The optimum manganese:silicon ratio was then explained by postulating that these fluid products were able to coalesce and that the larger particles formed floated out of the steel very quickly as predicted by Stoke's Law. The present work examines the effectiveness of various Mn-Si-A1 alloys as deoxidizers and their effects on the composition and removal of primary deoxidation products from a quiescent melt. EXPERIMENTAL TECHNIQUE Approximately 250 g of prepared Fe-O alloy, containing 0.045 to 0.055 pct O, were melted in an alumina crucible and deoxidized at 1550°C by plunging a thin steel cartridge containing the deoxidizer below the melt surface. A high frequency induction furnace supplying current at 8.5 kHz was used to heat a graphite susceptor, the interior of which had been machined to give a wall thickness of 0.85 in. to form a receptacle for the alumina crucible. The iron melt was essentially quiescent as the induced current was concentrated at the external surface of the graphite susceptor by the skin effect. A nonoxidizing atmosphere was maintained over the melt by passing a continuous stream of argon through the lid of the susceptor. The melt temperature was measured before deoxidation, and again at the end of an experiment by means

Jan 1, 1970

By Wllliam D. Davis

C OMMERCIAL production of oil in northeastern Oklahoma began in 1897 and in the next two decades this area became one of the greatest oil districts of the time. Its importance is now secondary, but thousands of wells in this area have produced uninterruptedly for more than thirty years. They are now classified as stripper wells. By means of what is known as water flooding their L. production can be considerably in- creased. This practice consists in injecting water under pressure into the sand surrounding an oil well, thus displacing the oil in the pores of the sand and forcing it into the oil well.

Jan 1, 1940

By Eugene McAuliffe

The term "mechanical mining" carries an ambiguity which justifies a preliminary word of explanation. . All mining activity conducted in this day is more or less mechanical; that is to say, power expressed in the form of electricity, steam or compressed air is used in some portion of practically every mining activity of consequence. "Mechanical loading" is more nearly correct than "mechanical mining" in reference to present practice. The first substantial effort made in the direction of mechanical mining, subsequent to the application of steam for hoisting and underground pumping purposes, was that of substituting for hand labor undercutting and shearing by power-driven machines. The undercutting of coal by hand represented at one time the most arduous task confronting the miner. Occupying a kneeling position in the thicker beds, or lying on his side in the thinner coal, the task was tedious and exhausting. The first attempt to substitute crude air-driven, and later electrically driven, "punchers," as the percussion type of machine was called, met with much the same opposition on the part of the workers as was expressed by workers in the other industries when any innovation, whether labor-saving or otherwise, was introduced. We should not be too critical of this attitude of mind shown by the mine workers. The peculiarly isolated character of the work carried on in semidarkness by a class of men who to a large extent lived and held themselves aloof from the other branches of society led long ago to the development of a craft consciousness which they have found difficult to surrender. It was not until 1891 that a definite record of the results obtained by the use of undercutting machines of all types was made available, the quantity undercut in that year totaling 6,211,732 tons of bituminous coal from all American mines. The volume of bituminous coal undercut by machines in 1928 totaled 369,687,007 tons, or 73.8 per cent. of the nation's production. In the light of this experience, we can properly feel that the work of introducing the coal-loading machine as a substitute for hand shoveling is making substantial progress.

Jan 1, 1931

By Charles W. Dickson

Jan 1, 1904

By Dudley Homer

MINAS DE MATAHAMBRE, S.A. is a Cuban mining corporation with mines located in the Matahambre district about 100 miles westerly from Havana in the Province of Pinar del Rio. The port of entry is the subport of Santa Lucia on the north coast of Cuba. The mines are located six miles inland at the town of Minas de Matahambre. Minas de Matahambre and Santa Lucia are connected by a 9-mile automobile road, and a 30,000-ft. Leschen aerial tramway. At the subport of Santa Lucia the company maintains docks, concentrate bins, tugs, lighters, and miscellaneous shipping equipment. The power plant of the company is also located at Santa Lucia. Connection between the power plant and the mine is effected by a 30,000-ft. transmission line. In the town of Minas de Matahambre are located the mines, concentrator, shops, and warehouses. The con-centrates are transported to Santa Lucia by the Leschen aerial tramway. The mines are equipped with three shafts, viz., Nos. 1, 2, and 3. (Fig. 1.) No. 1 Shaft is a three-compartment vertical tim-bered shaft and has reached a depth of 1825 ft. This is the present main hoisting shaft. No. 2 Shaft is a four-compartment vertical shaft lined with steel sets and native hardwood lagging. Certain portions where the ground is heavy have been lined with re-inforced concrete. Practically all production will be hoisted eventually through this shaft. No. 3 Shaft is a three-compartment vertical timbered shaft. It has reached a depth of 1090 ft. Its purpose is for prospecting, ventilation, and handling men and sup-plies through the north section of the mine.

Jan 1, 1933

Schedule of Events

Jan 1, 1977

By C. L. HUSTON

MY ANCESTRAL connection with the manufacture of boiler plate runs back through four generations, and my personal acquaintance with the practice reaches back to the time, in my ,boy- .hood days, when iron plates' were made in a mill operated entirely by water power. -The mill originally was driven by an old-fashioned "'breast" water wheel 20 ft. in diameter and with a20-ft. face, geared direct to the roll train. When the mill slowed up and there was danger of its stalling, the men would jump upon the rim and help the wheel around with their weight, to prevent a "sticker." Later, as large plates were called for, a flywheel was set out of line so that it could' be speeded up by gears from the water wheel and connected back again,. by reducing- gears, to the roll train. The flywheel, with its cast-iron rim and wooden spokes, made 90 r.p.m. and the roll train 45 r.p.m. In 1870, our company installed our first steam-driven plate mill two-high rolls, 84 in. long. In these early mills the hot metal was manipulated by hand.

Jan 1, 1920

By M. Sheffield

This paper presents a technique lor predicting the flow of oil, gas and water through a petroleum reservoir. Gravitational, viscous arid capillary lorces are considered, and all fluids are considered to be slightly compressible. Some theoretical work concerning the fluid flow in one-, two- and three-space dimensions is given along with example performance predictions in one- and two-space dimensions. INTRODUCTION Since the introduction of high speed computing equipment, one of the goals of reservoir engineering research has been to develop more accurate methods of describing fluid movement through underground reservoirs. Various mathematical methods have been developed or used by reservoir engineers to predict reservoir performance, 193-5,7,8 The work reported in this paper extends previously published work on three-phase fluid flow (1) by including a rigorous treatment of capillary forces and (2) by showing certain theoretical mathematical results proving that these equations can be approximated by certain numerical techniques and that a unique solution exists. DISCUSSION The method of predicting three-phase compressible fluid flow. in a reservoir can be summarized briefly by the following steps. 1. The reservoir, or a section of a reservoir, is characterized by a series of mesh points with varying rock and fluid properties simulated at each mesh point. 2. Three partial differential equations are written to describe the movement at any point in the reservoir of each of the three compressible fluids. All forces influencing movement are considered in the equations. 3. At each mesh point, the partial differential equations are replaced by a system of analogous difference equations. 4. A numerical technique is used to solve the resulting system of difference equations. Capillary forces have been included in two-phase flow calculations.1,4,8 The literature, however, does not contain examples of prediction techniques for three-phase flow that include capillary forces. Where capillary forces are considered, each of the three partial differential equations previously discussed has a different dependent variable, namely pressure in one of the three fluid phases. Therefore, three difference equations must be solved at each point in the reservoir. Where large systems of equations must be solved simultaneously, an engineer might question whether a unique solution to this system of equations actually exists and, if so, what numerical techniques may be used to obtain a good approximation to the solution. It is shown in the Appendix that a unique solution to the three-phase flow problem, as formulated, always exists. It is also shown that several methods may be used to obtain a good approximation to the solution. The partial differential equations and differenceequations used are shown in the Appendix. Matrix notation has been used in developing the mathematical results. Two sample problems were solved on a CDC 1604. They illustrate the type of problems that can be solved using a three-phase prediction technique. SAMPLE ONE-DIMENSIONAL RESERVOIR PERFORMANCE PREDICTION A hypothetical reservoir was studied to provide an example of a one-dimensional problem that can be solved. Of the several techniques available, the direct method of solution as shown in the Appendix was used. The reservoir section studied was a truncated, wedge-shaped section, 2,400 ft long, with a 6' dip. (A schematic is shown in Fig. 1.) This section was represented by 49 mesh points, uniformly spaced at 50-ft intervals. The upper end of the wedge was 2 ft wide, and the lower end was 6 ft wide. The section

Jan 1, 1970

By D. P. Harris

The construction of a model to associate probability of occurrence of some measure of mineral wealth with the geology for each subdivision (cell) of the area is postulated. The questions (1) are the observations made in reconnaissance geology sufficiently related to mineral wealth to distinguish the cells of high value from those of low value, and (2) can this geology be related mathematically to mineral wealth and probability are answered in a case study of 97,000 square miles in Arizona and New Mexico. Measurements on mineral wealth and geologic variables of 243 cells were made. The geologic variables, valued in counts, percentages and lengths, quantified the theoretical concepts of the model. It was found that multiple discriminant analysis and classification analysis by Bayesian statistics and multivariate normal probability function constitute a two-phase probability model that associates probabilities with geologic information and mineral wealth. The cells of explored area must be allotted the value class indicated by their cumulative production and estimate reserves (given well-defined geological relationships in a mineral wealth area), and a discriminant and classification analysis must be performed in which probabilities of the cell belonging to each of the value groups are generated as a function of the geologic variables. This determines whether high value cells can be distinguished from low value cells by their geology as well as indicating those cells misclassified by the model into a higher value group than warranted by their known mineral wealth. The second use of the model is for extrapolation. It is demonstrated how geologic information on an explored area can be utilized in guiding exploration in an unexplored area. Exploration decisions can be predicted on explicitly determined measures of uncertainty (the probabilities). SUMMARY This study postulates the construction of a model to associate probability of occurrence of some measure of mineral wealth with the geology for each subdivision (cell) of the area. Such a model will distinguish those cells deserving further exploration on the basis of their geology: The basic postulates of this study are as follows: v = Q(R,S,F,A) P(V) = G(R,S,F,A,V), where V = a measure of mineral wealth P(V) = the probability of occurrence of V R = age and type of rock F = rock fracturing A =age of igneous activity and contact relationships. There are really two questions to be answered: 1) are the observations made in reconnaissance geology sufficiently related to mineral wealth to distinguish the cells of high value from those of low value, and 2) can this geology be related mathematically to mineral wealth and probability? In order to answer these questions, an area of about 97,000 square miles situated chiefly in Arizona and New Mexico was selected as a case study. This case study area was divided into 243 cells, each 20 miles square, and measurements were made on mineral wealth and geologic variables. Crude geologic variables valued in counts, percentages and lengths are constructed to reflect the above postulated variables. These measurement variables thus provide quantified values defining the theoretical concepts of the model. It was found that multiple discriminant analysis and classification analysis by Bayesian statistics and the multivariate normal probability function constitute a two-phase probability model that associates probabilities with geologic information and mineral wealth. Given the availability of an area that is well explored and upon which the relationships of mineral wealth to geology can be adequately defined, there are two ways in which the analysis outlined in this paper can prove beneficial. First, the cells of the explored area must be allotted the value class indicated by their cumulative production and estimated reserves, and a discriminant and classification analysis must be performed in which probabilities of the cell belonging to each of the value groups are generated as a function of the geologic variables. Such an analysis determines whether cells of high

Jan 1, 1967

By Paul A. Farrar, Harold Margolin

The Ti-Al-V system has been delineated from 50 to 100 wt pct Ti and front 600 to 1400°C by X-ray and ntetallographic techniques. Isothermal sections were delineated at 600, 700, 800, 900, 1000, 1100, 1200, 1300, and 1400°C. X-ray and metallographic evidence indicated the presence of two phases and in addition to those reported by previous investigators of the ternary system'-3. T HE titanium-rich region of the Ti-Al-V system as originally proposed by Rausch et UZ, and Jordan and Duwez3 was based on the binary Ti-Al diagram as proposed by Bumps et uZ. As additional phases have been shown to exist5-' in the region previously thought to be all a, the titanium-rich region of the Ti-Al-V system is open to serious question. Therefore, in order to determine the effect of the indicated changes in the Binary Ti-Al system on the ternary Ti-Al-V system the present investigation was initiated. EXPERIMENTAL PROCEDURE The experimental procedures in this investigation are the standard techniques used in the study of titanium-alloy systems which have been described in detail previously.1° Consequently, only details pertinent to the present work are discussed. The alloys employed for the delineation of this system were prepared from titanium obtained from the Bureau of Mines (73 BHN) 99.99 pct Al and 99.7 pct V, by the consumable arc-melting technique. The titanium was premelted into buttons of 25 g because spattering during the first melt caused uncontrollable loss of alloying constituents. Typical analyses of the material used have been reported elsewhere Attempts to hot roll the alloys prior to heat treatment were made on the first series of alloys prepared, but as the area of extensive hot workability was fairly restricted, see Table I, this practice was discontinued. The times of isothermal annealing are given in Table 11. A preliminary heat treatment of 96 hr at 1000°C was used prior to heat treatment at lower temperatures. The standard techniques used for polishing specimens involved belt-grinding, grinding on emery paper, polishing electrolytically, and etching with Remington "A" etch. In the low-alloy region it was found that the oRo etch, developed by Ence and Margolin,o gave better contrast between phases. Where this procedure did not differentiate between phases clearly, the method of stain etching developed by Ence and was used. It has been previously reported15 that filing of titanium alloys is not desirable for producing X-ray powders, since the powder becomes contaminated by the file material. Therefore, for those samples not brittle enough to Crush, the procedure described below was used. The specimen was wrapped in molybdenum sheet and placed in a vacuum system and evacuated to 0.03 p. Palladium-pur if ied hydrogen was then admitted to the system until a partial pressure of 5o Cm of H was reached. The specimen was heated in the system to the temperature of original heat treatment and was slowly cooled over a period of 3 hr to 400°C while the partial pressure of hydrogen was maintained. The sample was removed from the system after it had completely cooled and was crushed to a powder of 230 to 270 mesh. The powder, wrapped in molybdenum sheet, was dehydrogenated at the temperature of original heat treatment until a partial pressure of 0.03 p was maintained in the system for at least 1/2 hr. The tube containing the powders was quenched in iced brine while still connected to the vacuum system. After dehydrogenation, the powder, except for the

Jan 1, 1962

By F. H. Deily, Jean M. Quets, Milton E. Wadsworth, John R. 222-000-000-012 Lewis, D. S. Rowley, R. J. Howe

Samples of synthetic magnetite were reduced in hydrogen-water vapor atmospheres in the temperature range 450o to 900oC. The reaction was always surface controlled, indicating the final products of reaction are nonfirotective. Three separate cases have been identified from the kinetic results: Case I, reduction of magnetite to iron below 570°C; Case II, reduction of magnetite to iron above 570°C; and Case 111, reduction of magnetite to wustite above 570 oC. In Cases I and 111 the kinetics have been explained by the formation of oxygen anion vacancies in the magnetite surface followed by associated diffusional processes. In Case 11 the observed kinetics have been related to the concentration of iron cation vacancies in the wustite layer formed, followed by associated steady-state diffusional processes. The concentration of cation vacancies in the wustite is maintained constant by the magnetite-wustite equilibrium. THE reduction of the oxides of iron has been a subject of study and interest for many years. However, few attempts have been made to interpret the results in terms of the mechanism of reduction of an iron oxide by either hydrogen or carbon monoxide. Stalhane and Malmberg' using CO, H2, and CO-Hz mixtures, developed the rate expression: where m = mass of oxide reduced, t = time, k = a constant, s = surface area, P = partial pressure of of CO or H,, and P, = partial pressure of the reducing gas at equilibrium. The rate of reaction per unit area was proportional to the difference between the partial pressure of the reducing gas and its pressure at equilibrium. Hansen, Bitsianes, and Joseph2 studied the reduction of pellets of hematite to magnetite with mixtures of CO-CO,. They concluded that below 450°C the reaction proceeded according to a model in which CO reacts with the hematite surface producing an oxygen ion vacancy. The rate controlling step was then assumed to be oxygen ion diffusion through vacancies resulting in the formation of magnetite. They derived an expression giving the rate of reduction proportional to the cO/CO, ratio. Recently McKewan3 published results for the reduction of magnetite spheres in atmospheres below 570°C. He explained his results by an equation of the form where K, is the equilibrium constant for wustite-iron equilibrium attributed to the formation of wustite as an intermediate in the reduction of magnetite. According to McKewan, Kp is an equilibrium constant for H, -HO adsorption in which oxygen is deposited on the surface from the H,Oand subsequently acts as a poison for reduction by hydrogen. Sample Preparation and Experiments. In this work the authors used the same apparatus and experimental procedure employed in the hydrogen reduction of magnetite. Sintered disk samples weighing approximately 1.5 g and measuring 1.2 cm in diameter and 0.25 cm in thickness were prepared by a method described previously.4 Partial pressures of hydrogen and water vapor were controlled by bubbling hydrogen through a series of flasks containing distilled and deionized water maintained at constant temperature in an oil bath. The total flow rate of the reacting gases—hydrogen and water vapor—was approximately 0.5 liter per min. The entire external system was maintained at a temperature above the oil bath to prevent condensation of water vapor. This was accomplished by wrapping electrical resistance elements over all surfaces. The glass column containing the weighing system-a McBain balance suspended from a gold chain-was enclosed in an aluminum tube heated by nichrome resistance wire enclosed in an insulating material. The temperature of the glass column was held constant by means of a series of thermocouples connected in parallel to a Leeds and Northrup temperature controller. This was necessary since variations in temperature resulted in expansion and contraction of the glass column and could be readily observed with the cathetometer. The spring extensions were measured through a window with a gaertner cathe-

Jan 1, 1962

By N. M. Levine, W. M. Fassell

In this laboratory study the problem of aerative conditioning to separate chalcopyrite and pyrite from cobaltite was simply effected with a sulfy-drate collector and pH by proper choice of mixing variables. It was shown that for a given impeller type and geometry, selectivity is governed by a relation between the Froude number and a modified power number multiplied by impeller tank-diameter ratio wherein the power factor is expressed as power intensity or horsepower per unit volume of contained pulp. In applying this approach to other systems, other criteria would be used in place of selectivity. The purpose of this paper is to show how solutions to problems of aerative conditioning of pulps may be enhanced by development of mixing parameters in a given system through application of a fundamental approach to agitation. The term aerative conditioning refers to a combination of processes which include mechanical gas dispersion, gas solution in the liquid phase, transport of dissolved gases and other reactants to the reaction zone, physico-chemico interaction within the liquid phase and/or at the solid surface, and, finally transport of products away from the reaction zone. Important elements of these processes are: 1) Air-Liquid Contact Area: This area limits the rate at which a given gas may dissolve in a given liquid. Thus, an aerative conditioning system should be designed for optimum gas dispersion. 2) Diffusional Factors: Such factors as concentration gradient, diffusion film thickness, and diffusivity may govern the rate at which dissolved constituents are transferred to the zone of interaction at a particle surface and the rate at which reaction products are transported therefrom. Thus, such systems would be designed for maximum turbulence to effect good mixing and to minimize diffusion film thickness. 3) Solids-Turbulent Liquid Contact Time: Sufficient time should be provided for interactions to take place at solid-liquid interfaces. The region of maximum turbulence for mechanical systems being in the impeller zone, it is important that the number of passes through this zone be optimized. This means that a proper balance should be struck be- tween flow and turbulent power to achieve optimum conditioning time. Too high a flow rate and insufficient turbulence may be improper if the reactions are diffusion limited. On the other hand, too much turbulent power and too little time in the reaction zone due to insufficient flow power may also be limiting. 4) Geometry and Impeller Design: The design of the conditioning vessel and the type of impeller employed are important factors in determining the relative distribution between flow and turbulent power and the degree of gas dispersion. Maximization of power input would be to no avail if the distribution between flow and turbulent power were improper or gas dispersion insufficient. 5. Physical Chemistry: The reactions between dissolved gases and solid surfaces may be limiting if gas solubility, activation energies and/or free energies are not favorable. J. H. Rushton, E. W. Costich, and H. J. Everett' have summarized the mechanical elements of the combination of processes listed in a fundamental mixing equation. This equation was derived by dimensional analysis and relates the physical variables for a single impeller, centered in a cylindrical, vertical axis, flat-bottomed tank. It is, where T is tank diameter in feet; H is liquid depth in feet; C is height of impeller off tank bottom in feet; S is pitch of impeller; L is length of impeller blades; W is width of impeller blades; R is number of baffles; D is impeller diameter in feet; Np is the power number, pg/dN3D5; P is power in foot-pounds per second; g is the gravitational constant, feet per second; J is width of baffles; B is number of im-

Jan 1, 1961

By R. Ebeling, M. F. Ashby

The paper is in two parts. The first develops the formulae and method needed to calculate the size, nu)nber, spacing, and volume fraction of hard or inert particles in the interior of a specimen from measurernents made on an extraction replica; throughout, the spread of- particle sizes in a single specimen is taken into account, and the extraction efficiency of the replica is considered. A method for testing whether the particles are randotnly distributed in space is described, and the spacing of randomly distributed particles is discussed. The second Part describes the application of the method to copper containing spherical particles of silica; the description includes an estimate of the errors involved, and a comparison of this with alternative methods. All parameters except uolume fraction can be determined satisfactorily, and the method offers advantages over other electron-,rzicroscopic techniques when dealing with hard particles in a softer matrix, or inert particles in a chem-ically less inert matrix. 1 HE experimental measurement of sizes and numbers of discrete particles of a second phase embedded in a matrix material from opaque, plane sections has been considered by many authors, notably by Fullman.' It is assumed that, when the specimen is sectioned, the particles are also sectioned, so that the diameters of the circles of intersection of particles with the plane of the cross section ("surface diameters") are measured. It is difficult to derive the distribution of true particle diameters ("volume diameters") from measurements of the distribution of "surface diameters" on a plane section. The measurement of size and numbers of small second-phase particles by transmission electron microscopy through thin foils of matrix containing the particles has been described by Cahn and ~uttin~' and by ~illiard.~ Because of overlap and the fact that particles which intersect the foil surface may be sectioned whereas those in the bulk of the foil are not, it is again difficult to measure the true distribution of particle sizes. The use of replicas for this sort of measurement has not been analyzed in detail. A replica made from an opaque cross section, thus replicating the circles of intersection of particles with the plane of section, is analyzed by Fullman's method and suffers from the same difficulties. Under certain circumstances, however, extraction replicas can be used, and offer a special advantage in that they make the determination of the true distribution of particle diameters particularly simple. It is the purpose of this paper to describe this extraction replica method. Consider the example of an alloy consisting of SiOz particles, whose mean diameter is about 1000A, dispersed in a copper matrix. When the alloy is sectioned and mechanically polished, the particles are not sectioned, because they are much harder than the matrix, and so will be either left in the surface or pulled out whole, and because the particle size is smaller than the abrasive size of even the finest abrasive. The particles are chemically inert in solutions which chemically etch or electropolish the matrix, so that chemical treatments do not section the particles either. (Experimental measurements of particle shape in this alloy confirm this—truncated particles are never seen.) Small, hard or inert, particles are therefore not sectioned when the specimen is sectioned and polished. An extraction replica taken from this polished surface shows the true "volume" diameter of each extracted particle; the distribution of diameters seen on the replica is the surface distribution of true "volume" diameters, and the volume distribution of true "volume" diameters is easily derived from it. The extraction replica method is not subject to the difficulties associated with sectioning of particles, and avoids the problem of overlap from which the transmission method suffers. The method is well-suited for studying hard particles in a soft matrix. Examples are provided by internally oxidized alloys, oxide-dispersion strengthened metals like T.D. Nickel, and carbides, nitrides, and strong intermetallic compounds in metals. It should be possible to adapt polishing techniques in alloys containing softer but inert particles to avoid sectioning the particles (say by electropolishing or etching). The method is tested and illustrated in Sections 8 and 9 by applying it to a dispersion of spherical SiO2 particles in a copper matrix. I) SYMBOLS Symbols are defined where they first appear in the text. Volume fractions of particles are denoted by the symbol f, particle diameters by x, center-to-center particle spacings by D, and numbers of particles by N. Mean particle diameters and standard deviations about these means are denoted by x and a. Both arithmetic (subscript A) and geometric (subscript G) means are employed. In this paper we measure the distribution of true diameters of particles which touch or pass through a random-plane section of the specimen. We may want to know the distribution of particle diameters in the

Jan 1, 1967

By S. R. B. Cooke, H. S. Choi, D. H. Harraway, I. Iwasaki

The mineralogy of natural iron ore samples and their slimes have been investigated and the nature of slime interference in iron ore flotation has been studied. The results have been correlated with the flotation behavior of a natural ore sample. Various conclusions have been reached as a result of these studies. In the flotation of iron oxide ores, desliming is generally considered to be an essential step to successful separation, irrespective of whether the iron oxide or siliceous gangue minerals are to be floated, although some workers have found empirically that certain collectors and reagent combinations are less sensitive to the presence of slime than others. The detrimental effect of slime is considered to be twofold. First, the presence of slime presupposes a high reagent consumption because of high specific surface. When clays are present and when cationic collectors are used abstraction by ionic exchange may augment this condition. Attempts to compensate by the addition of large amounts of reagent result in only partial correction. Second, slime coatings on granular particles tend to interfere with the bubble-mineral contact. The nature of slime coatings in flotation is quite complex and has been the subject of considerable study; an attempt was recently made by Fuerstenau et al.' to relate the slime-coating density with flotation recovery and with the properties of the electrical double layer at the mineral surfaces. Although major constituent minerals in the oxidized iron ores of the Mesabi and Cuyuna ranges are hematite and goethite (limonite) as the iron oxides, and quartz and chert as the siliceous gangue, very little is known of the mineralogy and of the chemical and physical characteristics of the slimes, and still less of the interaction between slimes, collector, and the mineral surfaces. For pragmatic reasons iron ore slimes are defined as — 20p material, based upon the calculated settling velocity of a quartz sphere of the stated diameter, and of all other equal-settling mineral particles. Active slime interference with flotation is usually attributed to particles 5p in size or finer, the extent of such interference appearing to depend not only on the mineralogy but also on the size distribution of each mineral in the slime fraction. The objective of this work was to acquire a more specific knowledge of the constitution of iron ore slimes and of their role in flotation. The mineralogi-cal composition of natural slimes was obtained by differential thernal analysis (hereinafter referred to as DTA), electron microscopy, and chemical and X-ray analyses. Some flotation tests were made on natural ore samples. The surface properties of several constituent minerals were investigated by electrophoretic measurements and by determination of the adsorption of some typical flotation collectors. Finally, simplified flotation tests were made on granular goethite and quartz in the presence of various artifically prepared slimes; the results were compared with laboratory flotation tests made on natural ores. MATERIAL AND METHODS Mineralogy of Some Iron Ore Slimes: Samples of two wash-ore tailing::, hereinafter identified as A* and B, *Sample A of the present investigation 18 the same am ore A in ref. 3. of a wash ore C, and of a paint rock D, all from the Mesabi range, were selected for investigation on the basis of prior information concerning their flotation behavior. The two wash-ore tailings, when deslimed, were known to respond well to flotation, whereas the wash ore was high in goethite, tended to be slimy, and responded poorly to flotation. The paint rock also exhibited sliming tendencies, and was suspected to contain relatively large quantities of clay minerals because of its high A1203 content. Gruner states that the paint rock of the Mesabi frequently contains kaolinite. To ascertain the relative sliming tendencies of each sample a standardized desliming method was employed. All samples were ground through 65 mesh using jaw and rolls crushers. A 500-g sample of each

Jan 1, 1962

By J. B. Morrow

WITH numerous plans under consideration for coal classification, and with the advent of the Bituminous Coal Code, the intelligent sam-pling of coal has become increasingly important. To us it is rather significant that there have been very few fundamental studies of coal sampling in American technical literature since those of E. G. Bailey, which appeared in the Journal of Industrial and Engineering Chemistry in March, 1909. He covered the subject up to that time so thoroughly and in such an excellent manner that perhaps many other later students have felt that they could add very little to his findings. The recent studies of the British Engineering Standards Association have indicated the possibility of a somewhat different interpretation of Bailey's results, permitting the taking of smaller samples, and perhaps it will now be helpful to reopen this question. C. W. H. Holmes, in an informative series of articles on coal sampling recently published in Colliery Engineering, makes two rather interesting statements, as follows: It is scarcely surprising to find a lack of interest and knowledge regarding the sampling of coal not only in the mining industry itself but also among consumers of industrial fuel: at its best coal sampling is a dirty business, regarded as a nuisance and an expense by the commercial man, and usually as a nuisance and nothing else by the chemist. The writer can conceive only two classes of people who have never experienced any difficulty in obtaining representative samples of coal from wagons; those who have never tried to, and those who have never had the necessity or desire to check the accuracy of their work. The primary purpose of this paper is to present some tabulated data of the more significant results of a sampling investigation undertaken during the last four years to obtain certain fundamental data on the variables connected with coal sampling and to point out that often assumptions have been made that are not in accordance with the facts. One of the standard sampling methods states:

Jan 1, 1935