Search Documents

By Donald L. Katz

Charts for predicting the pressure to which natural gases may be expanded without hydrate formation have been prepared for gases of even gravity. Pressure-temperature curves for hydrate formation were established for gases having gravities from 0.6 to 1.0. These curves and the thermal behavior of the gases during free and adiabatic expansion were used to prepare the charts for estimating the permissible expansion of natural gases without hydrate formation. The problem was solved by L. F, Albright, W. T. Boyd, J. J. McKetta, G. Martin, P. Poettman. and A. P. Snyder.-, who are first-year graduate students in the department of Chemical and Metallurgical Engineering at the University of Michigan. This paper is essentially a summary of their results. Prediction of Conditions for Hydrate Formation in Natural Gases Each natural gas under a given pressure will form solid hydrates at a corresponding temperature provided sufficient water is present.1-5 The temperature of natural gases below about 5000 lb. per sq. in. decreases when the gases are expanded freely.6,7 This decrease in temperature may cause the expanding gas to enter the region of temperature and pressure at which hydrates will form' The final pressure to which a natural gas may 'be expanded without hydrate formation depends upon the initial temperature and pressure and the gas composition. This paper presents charts that give the final pressures to which gases of gravity 0.6 to 1.0 at given initial temperatures and pressures may be expanded without formation of hydrate. Hydrate-forming Temperatures and Pressures as a Function OF Gas -Gravity Experimental data of pressure versus temperature at which solid hydrate will form, provided sufficient water is present, are available for a series of gases.2,3 A method of predicting the pressure-temperature curve for a given gas composition has been reported.' The solution to this problem requires that these curves relating pressure to temperature be established for gases of given gravities.

Jan 1, 1945

By G. D. Rieck, G. H. G. Vaessen, D. L. Vogel

Both doped and undoped tungsten single crystals exhibit hardness anisotropy with respect to the direction of testing in each of the crystallographic phes investigated. The hardness anisotropy of undoped single-crystal tungsten is rather pronounced in (001) and (110) planes but very minor in (111) planes. The anisotropy in (122) planes of the doped and drawn tungsten after recrystallization is in accordance with a previously published concept of a stringlike distribution of the doping material in the metal. ANISOTROPY in mechanical properties of single-crystal tungsten was investigated by Rose et al., Garlick and Probst,2 and Beardmore and Hull. 3 Although data on the Vickers microhardness of tungsten have been published (see, e.g., Boosz 4 and the references cited by him), no data on the microhardness anisotropy are available. We report, therefore, some of our own results on the microhardness and its anisotropy. The microhardness has been determined of the following samples. A) Polycrystalline tungsten samples taken from: 1) powder metallurgical tungsten "normally" doped with potassium-silicon-aluminum oxides (final contents inppm: K, 100; Si, 100; Al, 20; Cr, 20; Fe, 50; Mo, 400; Ni, 10) and in the form of: a) a 10-mm-diam swaged ingot annealed at 1600°C, the grain sizes varying between 15 and 250 p; b) a sheet rolled at about 800°C and recrystallized at 2000°C7 the grain sizes varying between 15 and 150 p; c) a 2-mm-diam swaged rod, as-worked, with elongated grains (average diameter of about 25 , lengths up to 1 mm); 2) undoped electron-beam-melted tungsten with very large grains (contaminations in ppm: K < 10; Fe < 20; Cr < 10; Cu < 0.1; Ni not detectable; inter-stitial~ not determined). B) Single-crystal samples taken from: 1) pure tungsten grown on a Pintsch wire by the van Arkel procedure (main contaminations inppm: Mo, 100; Si < 10; Cu and Fe, 2; A1 < 2; interstitials not determined); 2) zone-melted undoped tungsten (analysis as under A2); 3) large crystals in secondary recrystallized tungsten

Jan 1, 1969

By W. J. Helfrich, R. A. Dodd

Binary aluminum solid-solution alloys containing various amounts of silver, magnesium, and zinc were prepared by careful directional solidification, and the hydrostatic and X-ray densities were compared. With the exception of the Al(Ag) alloys, the X-ray densities were consistently greater than the hydrostatic measurements, in agreement with earlier observations by Ellwood. In contrast to Ell-wood&apos;s interpretation in terms of vacant lattice sites associated with Brillouin zone effects, a tentative explanation based on the existence of solidification microshrinkage was favored. This hypothesis was confirmed by an examination of Al(Zn) alloys prepared by vapor diffusion of zinc into aluminum. The hydrostatic and X-ray densities were now in very close agreement, and it was concluded that the filling of Brillouin zones in aluminum solid-solution alloys does not necessarily result in the formation of defect structures containing an excess of vacant lattice sites. ThE existence of defect structures of the vacancy type in alloys in which the excess vacancies have an electronic rather than a thermal or mechanical, and so forth, origin is well recognized. Examples of incomplete lattices of this type are to be found in the Ni-Al,1-3 Fe-Ni-A1,4 c~-Ni-Al,5 Fe-Cu-Al,= and Co-A17 systems. These defect structures are of a special kind in that the intermediate phases possess an ordered atomic arrangement or superlattice, and in some instances the vacancy concentration may be unusually large, e.g., at 45.25 at. pet Ni in NiA1, approximately 8.8 pet of the lattice sites are unoccupied. Ellwood8-10 has reported similar defect structures in the aluminum solid solution alloys of the Al-Zn and A1-Mg systems and in alloys of the Au-Ni system." In Al(Zn) the (apparent) vacancy concentration rose, somewhat irregularly, to a maximum of about 2 pet vacant sites at 25 at. pet Zn, while in Al(Mg) the (apparent) vacancy concentration increased continuously to 1.7 pet at 15 at. pet Mg. An explanation in terms of Brillouin zone overlap was attempted, although Pearson12 has pointed out the difficulty of reconciling the observations with zone theory. However, the possibility of the effect being caused by the Fermi surface just touching a plane of energy discontinuity inside a prominent Brillouin zone has, in general, been accepted. In fact, Massal-ski13 has interpreted Ellwood&apos;s8 observations as confirmation of Leigh&apos;s14 theoretically predicted zone overlap occurring at approximately 2.67 electrons per atom. Unfortunately, Massalski was apparently unaware that Ellwood9 had revised his earlier results considerably, and the revised data did not confirm Leigh&apos;s analysis. Ellwood&apos;s clata were reexamined by the present authors who noted a possible correlation between the percentage defects as a function of alloy composition and the temperature interval of solidification measured from the respective equilibrium diagrams. This suggested an explanation in terms of shrinkage porosity rather than vacant lattice sites, and pointed to the desirability of reexamining appropriate alloy systems using: both Ellwood&apos;s method of specimen preparation (casting followed by wrought fabrication) and alternativ&apos;e methods, i.e., diffusion, which might be expected to minimize, or even completely obviate, microporosity. ALLOY PREPARATION 1) Cast Allolys and Aluminum Single Crystals. Al(Ag), Al(Mg;l, and Al(Zn) alloys of various compositions up to 20 at. pet silver, 13.5 at. pet mg, and 30 at. pet Zn were prepared by melting under helium and casting into graphite molds. In the first two systems, the maximum alloying addition was quite close to the limit of solid solubility, but the possibility of transformation to a&apos; during quenching somewhat restricted the suitable Al(Zn) composition range. The alloys were prepared from high-purity aluminum, a lot analysis showing 0.002 wt pet Cu, 0.002 wt pet Fe, and 99.996 wt pet A1 by difference. The silver, magnesium, and zinc were of 99.99+, 99.98+, and 99.998 wt pet respectively. Each composition was analyzed chemically. The as-cast ingots measured 7/16 in. diam and 5 in. length. One in. was removed from the top of the ingot, and the bottom 3 in. was machined to 0.275 in. diam; a point was also machined on the smaller diameter end. The remainder of the original ingot served as a top riser during subsequent remelting and controlled solidification. The machined ingots were now remelted using a Bridgman soft-mold technique to ensure directional solidification and, therefore, a minimum of micro-shrinkage. Alumina powder was used as mold material contained in an alundum thimble, and this crucible was placed in a helium-filled Vycor tube. The assembly was lowered through a suitable temperature gradient at approximately 0.5 in. min-l, and the risered portion of the casting was subsequently removed by sawing.

Jan 1, 1962

By Charles Clayton

A study of the literature shows that the greater part of research work on annealing of cold-worked iron has been for the purpose of studying the effect on grain-size and properties other than hardness. No reference has been found of experimental work of the same nature as that explained in this short paper. The material used throughout was Vismera iron, an iron containing 0.03 carbon and made several years ago by the Inland Steel Co. One-half inch stock was cut into cylinders ¾ in. long. The cylinders were then compressed for 60 sec. in a Reihle testing machine under loads as indicated below: COMPRESSION, AVERAGE LENGTH, SERIES POUNDS INCHES 1 10,000 0.693 2 15,000 .599 3 20,000 .501 4 25,000 .426 5 30,000 .378 6 35,000 .351 7 40,000 .311 Fig. 1 shows these cylinders after compression. Each series con¬sisted of 17 specimens lettered 0, B, C, D, E, E:, G, H, I, J, K, L, M, N, P, Q, and R. One specimen of each series was reserved for study of the properties in the cold-worked condition. The other specimens were annealed in a Hump furnace for ½ hr. at the following temperatures:

Jan 2, 1926

By C. Laird, C. E. Feltner

An investigation into the effect of a material&apos;s slip character on its high strain fatigue properties has been carried out using copper and Cu-7.5 wt pct A1 as representative wavy and planar slip mode materials, respectively. In copper, the constant term and exponent in the Coffin-Manson equation, ?EpNf1/2 = const, are unaffected by the temperature of testing or the history of the metal. On the other hand, in Cu-7.5 wl pcl Al, while the exponent is invariant, the constant is increased with respect to copper and increased further with decrease in temperature. The life in Cu-7.5 wt pct A1 is double that of copper at room temperature and about four times at 78°K. Fractoflaphic studies indicate that these diffevences in life are associated with the early stages of cracking. In copper, severe surface rumpling provides crack nuclei at pain boundaries independent of&apos; testing temperature or the history of the metal. In Cu-7.5 wt pct Al, the planar slip mode of deformation prevents grain boundary folding; crack nucleation is therefore mainly transgranular and the increase in life with respect to copper is associated with a prolonged linking-up stage of such transgranulay cracks. At the lower temperature the increased difficulty of cross slip inhibits multiplication of trans-granular cracks and retards the linking-up process, giving a further enhaancement in life. It is expected that such behavior will be found general in materials of wavy and planar slip mode, respectively. STAGE II crack propagation in high strain fatigue takes place by a repetitive process of crack tip blunting in the tension part of a fatigue cycle followed by resharpening of the crack in the compression part.1-3 This mechanism has come to be called the "plastic relaxation process".3 At very high strains (lives to failure less than 103 cycles), most of the life of a specimen is spent in crack propagation by the plastic relaxation process.4,5 Since the differences in the cyclic strain hardening behavior of metals and alloys are comparatively small in this strain range,6,7 the amount of blunting at a crack tip depends primarily on the applied strain amplitude. The rate of crack propagation in this life range is therefore nearly constant with respect to material and temperature of testing. In the longer life portion of the high strain fatigue range (l03 to 103 cycles to failure), a considerable fraction of the lives is spent in crack initiation and Stage I growth. Grain boundaries have frequently4,5,8 been found to be the sites for this growth which is also associated with a surface folding process.4&apos;5 Such folding behavior may also be general in any material having a grain structure and capable of plastic deformation. It has therefore been suggested475 that the universality of the Coff in-Manson law,9&apos;10 constant,* where ?Ep is the plastic strain range and Nf the number of cycles to failure, is reflected in the approximate invariance of both the crack initiation and propagation behavior. It happens that, in most investigations of the phenomena associated with failure,4,5,8 materials with a wavy slip mode have been used as vehicles for the studies, or else "normally" planar slip mode materials have been tested under conditions giving rise to wavy glide deformation, e.g., stainless steels cycled at high temperature.&apos;&apos; The purpose of the present investigation was to determine whether or not different cracking phenomena would occur when the slip mode of a material is planar and if the associated life to failure would be different than that of a wavy slip

Jan 1, 1968

By C. H. Li, R. J. Stokes, T. L. Johnston

The phenomenon of solid-solution strengthening has previously been studied in a number of binary alloy systems.1-8 There has been, however, very little information published concerning the strengthening effects of specific solutes in magnesium alloys. Schmid and his coworkers9,10 investigated the behavior of aluminum and zinc in binary and ternary magnesium-alloy single crystals, but this work was done before high-purity materials were readily available. Workers at the Dow Chemical companyH reported increases in the critical resolved shear stress upon alloying magnesium single crystals with zinc and indium. Recently, Hardie and parkins* investigated the extent of hardening produced by the addition of various solutes to poly crystalline magnesium. The present work was undertaken to provide data on the strengthening effects of a number of solutes in high-purity magnesium, for the purpose of supplying further experimental information which might be useful in describing a general mechanism for solid-solution strengthening. To simplify interpretation of the results, the mode of deformation was limited to basal slip, through the use of single crystals. EXPERIMENTAL PROCEDURE Magnesium and magnesium binary-alloy single crystals containing indium, cadmium, thallium, aluminum, and zinc were prepared in the form of l/2-in.-diam rods, approximately 8 in. long, using a modified Bridgman technique in which the crystals were slowly cooled from the melt in a steep temperature gradient, in an atmosphere of helium. It was found that a solid-liquid interface travel speed of about 0.7 in. per hr consistently produced single crystals. The poly crystalline starting materials for the preparation of single crystals consisted of 1/2-in.-diam extruded rods, prealloyed to the desired composition. The unalloyed magnesium and magnesium-indium extrusions were furnished by the Dow Chemical Co. The other alloys were prepared at the Rensselaer Polytechnic Institute Metallurgical Laboratories. Some preliminary studies of the strengthening effect of indium were conducted at room temperature using a constant rate of tensile loading of 1040 g per min. Stress was applied to the crystals by means of a simple 5:l lever arm. The lever was loaded by a constant rate of flow of shot into a receptacle suspended from the long arm of the lever. Plastic flow was detected by an electrical resistance strain gage cemented to the surface of the crystal normal to the minor axis of the predicted glide ellipse. The crystals were acid machined to produce tensile specimens with a reduced section between the grip ends, with an additional step in the center of the reduced section to compensate approximately for the slip-retarding effect of the strain gage. The balance of the single crystals were extended in an Instron tensile tester. This machine employs a synchronously driven screw and automatically records applied load as a function of cross-head separation. It became unnecessary therefore, to employ a strain gage to detect deformation or to acid machine a reduced section. Preparation for testing reduced merely to chemical cleaning of the surface, thus minimizing the amount of handling and probability of accidental damage to the crystals. The rate of elongation employed in all the tests was 0.002 in. per min, corresponding to a strain rate of approximately 0.0004 per min. EXPERIMENTAL RESULTS The investigation confirmed the finding of many workers that the yield strength of hexagonal metal crystals is strongly orientation-dependent. This is illustrated in Fig. 1, in which o, the tensile stress required to produce gross plastic flow in eleven unalloyed magnesium crystals stressed at a constant rate of loading is plotted as a function of sin X, cos Ao where X, is the angle between the

Jan 1, 1960

By G. R. Speich, D. J. Mack

The transformation of was studied by isothermal methods. At all temperatures, the ß transforms quickly to fine grained ß" which develops silver-rich striations. At higher temperatures the striations disappear, the final structure being Widmanstatten a in ß&apos;. At lower temperatures, the striated ß" is consumed by pearlite nodules of a + ß&apos; which in turn form the Widmanstatten a in ß&apos;. The transformation is unlike any previously reported for a eutectoid. AS part of a general program of study on the eutectoid reaction, the Ag-Cd eutectoid seemed particularly attractive because the ß phase which undergoes the reaction is another of the typical "electron compounds," AgCd, having the disordered body-centered cubic structure. This work deals with the eutectoid which occurs at 50.5 wt pct Ag, and not with the eutectoid which has been reported at 42.9 pct Ag.&apos; There has been no work reported specifically on the Ag-Cd eutectoid which was studied. The only information available on this eutectoid is that work done in the determination of the phase diagram. For the most part, the terminal portions of the diagram, Fig. 1, are well established; however, the region from 40 to 60 pct Cd is still somewhat in doubt. The X-ray evidence&apos;..&apos; in this region is in conflict with the results of thermal analysis. X-ray analysis3 does not show a polymorphic transformation at about 240°C as indicated by thermal analysis.1,5 Even the X-ray evidence, within itself, is confusing in this region of the diagram. One investigator2 reports the ß phase as hexagonal close-packed and has found three phases in the one-phase ß field. Other X-ray investigators"&apos; &apos; report the ß phase as body-centered cubic. The authors believe that much of the confusion resulted from incomplete homogenization of the alloys. It was found that it takes almost a week to produce a completely homogeneous two-phase structure at 370°C. Another possible source of error is the volatilization of cadmium from the surface and cracks of the specimen during annealing with the possible formation of a cadmium-poor phase. The only metallographic data available on this eutectoid alloy are those of Durrant1 and Fraenkel and Wolff.5 his information is very limited. The phase diagram chosen as most nearly correct is that in the Metals Handbook," which is almost identical with the phase diagram suggested by Durrant.1 Materials and Procedure The alloy was prepared from high purity silver (999.5 plus fine) and high purity cadmium (0.02 Pb, 0.005 Cu, trace Fe). The metals were melted in carbon under a nitrogen atmosphere. Some cadmium was lost by volatilization but by remelting several times and adding cadmium a 200 g ingot of approximately eutectoid composition was obtained. Because the CdO fumes are quite toxic, the exit gas from the furnace was led through a water trap to condense the CdO. The ingot was homogenized at 650°C for 24 hr, no attempt was made to prevent decadmiumization. This resulted in a narrow decadmiumized rim on the ingot which was removed. Filings for analysis were obtained from cross sections of the ingot. Silver was determined by the Volhard thiocyanate method,? cadmium by difference. The ingot analyzed 50.8 pct Ag at the top of the ingot and 50.7 pct at the middle and at the bottom of the ingot. This alloy was only slightly hypo-eutectoid compared to the accepted value of 50.5 pct Ag and was used for the isothermal studies. It was felt that further attempts to adjust the composition might be futile because of the volatility of the cadmium. The ingot was sectioned to specimens approximately 3/4 x 3/4 x 1/8 in. These specimens were "austeni-tized" for 3 hr in air at 650°C to yield homogeneous ß and then quenched into a salt bath held at constant subeutectoid temperatures where the transformation

Jan 1, 1954

By A. T. Sweet, C. E. Plummer, H. W. St. Clair, S. F. Ravitz

The ammonium sulphate process for recovering alumina from clays was proposed by Rinman, Buchner, and others many years ago, and more recently various modifications have been investigated both here arid abroad.l-Is The process, as it is being investigated by the Bureau of Mines, involves the following essential steps: (I) sulphating the alumina in the clay by baking with ammonium sulphate at approximately 4m°C., (2) leaching with water to extract aluminum sulphate and ammonium sulphate, (3) crystallization of ammonium alum, (4) conversion of the alum to aluminum hydroxide by the ammonia gases given off during the baking, and (5) calcining the aluminum hydroxide to alumina. The over-all reaction between kaolinite (the most important alumina mineral in most clays) and ammonium sulphate during the baking step may be expressed as follows: Al2O8.2SiO2.2H2O + 4(NH4)2SO4 = (NH4)2SO4.A12(SO4)3 + 6NH3(g) + SH2O(g) + 2SiO2 [i] There is definite evidence. as is shown later. that the aluminum occurs in the baked product as anhydrous ammonium alum rather than as aluminum sulphate, provided the baking temperature is not much above 4o0°C. It is probable that the reaction takes place in the following steps: (NH4)2SO4 = NH3 -(- NH4HSO4 [2] Al2O3.2SiO2.2H2O + ;}NH4HSO4 = A12(SO4)3 + 3NH3 + 5H2O + 2SiO2 [3] A12(SO4)3 + (NH4)2SO4 = (NH4)2SO4.A12(SO4)3 [4] In onc modification of the process, the ammonium sulphate is first decomposed according to Eq. z, and the clay is treated with the resultant ammonium acid sulphate. Reaction I is highly endothermic. On the basis of the best available data, the following values have been estimated for the changes in heat content and free energy in calories per mol: -AH = 331,040 - 34T -AF = 331~040 - 78.3T log T - 671.8T The heat required&apos; at 25OC is 320,900 cal. per mol, or 5650 B.t.u. per pound of alumina. The theoretical equilibcium pressure of NHa, based on the free-energy equation given above, increases very rapidly as the temperature rises above 3o0°C., and reaches one atmosphere at 43s°C. Ammonium alum solutions are almost ideal for crystallization. A saturated solution of ammonium alum contains 126. grams of AlzOa per 1000 grams of water at 90°C. and only 16.5 at 20 C. Hence most of the alum crystallizes out when the

Jan 1, 1944

By C. J. Rosa, W. C. Hagel

An attempt is made to determine the diffusion coefficients of oxygen ions in hypostoichiometric zirconium oxide. A phenomenological theory is developed for three-phase, unidirectional volume diffusion of a gaseous species from a planar source. Knowledge about oxygen diffusion in a and ß zirconium and experimentally measured rates of movements of interfaces permit the evaluation of oxygen ion diffusivi-ties in ZrO2-x. The results conform to the relationship: sq cm per sec, for the temperature range of 875" to 1050° C. DIFFUSION coefficients of oxygen ions in stoichio-metric oxides have been studied by many investigators. The obtained results not only supplement the knowledge about the lattice-defect structures of oxides and conduction mechanisms but also provide information of technological importance. Rate processes such as oxide sintering, high-temperature creep deformation, and oxidation of metals and their alloys are directly dependent on diffusion phenomena. Unfortunately, diffusion coefficients obtained from studies on stoichio-metric oxides cannot be treated without restraints when applied to oxidation kinetics, if precise evaluations of oxidation rates are desired. Oxides formed on metals are usually nonstoichiometric and exhibit nonuniform distribution of either cation or anion vacancies across their thicknesses. Debuigne and Lehr1 extended Danckwerts&apos;2 mathematical analyses and furnished a semitheoretical treatment for evaluating oxygen diffusion coefficients in zirconium oxide in terms of weight gain measurements during oxidation of zirconium in the temperature range 400° to 850°C. Their calculations are based on theoretical partitioning3 of the total amount of oxygen between a zirconium and its oxide phase. An inherent discrepancy appears to continue throughout their calculations. The amount of oxygen confined to the oxide phase should be corrected by multiplying the calculated oxide thickness by the inverse of Pilling-Bedworth ratio, if expansion of zirconium dioxide is taken into account. The purpose of the present investigation is to provide a new semitheoretical treatment for evaluating diffusion coefficients of moving species in hypostoichiometric oxide. The analyses are relevant to unidirectional volume diffusion. Although the presented method is quite general, its applicability will be discussed in terms of kinetic measurements from oxidation of zirconium at temperatures above the a/ß transition, for reasons stated in the later part of this paper. EXPERIMENTAL Pure, 99.93 wt pct, zirconium samples of approximately 2 by 1 by 0.35 cm were exposed to oxygen for various times at four temperature levels: 875°, 950°, 1000°, and 1050°C. High-purity, better than 99.9 vol pct oxygen was passed through a cold trap and columns containing anhydrous CaSO4 to remove residual water vapor. Before exposing to oxygen at a pressure of 500 Torr, specimens were subjected to wet abrasion on 200- through 600-grit Sic papers and polished with 1—p diamond dust. Prior to oxidizing, all zirconium samples were vacuum-annealed at 10-6 mm Hg for about 15 min at the test temperature. The temperature variation across the uniform heat zone was ±2°C from the preset value. Final polishing, for phase thicknesses measurements, was performed by using 8- and 1-p diamond dust and followed by vibrator polishing with 0.05-µ ? Al2O3 solution. Measurements of phase thicknesses were made by projection on a metallographic viewing screen. Conventional powder X-ray analyses for the oxide were employed. RESULTS Fig. 1 is an example of the cross section of oxidized zirconium. Designations of phases given below this figure are the same as those used in the three-phase diffusion system represented by Fig. 5 in the following section. Zirconium oxidized for longer exposure times showed two types of oxides: white oxide at the surface and an underlaying layer of gray oxide. X-ray powder patterns of these oxides at room tern-

Jan 1, 1969

By R. G. Charles, E. A. Gulbransen, S. Barnartt

KINETICS of the reaction of zirconium with pure oxygen at elevated temperatures have been studied by several workers for periods of time up to 6 hr.1-1 In two cases,3-4 . the experimental values of oxygen uptake, w, as a function of time, t, were best fitted to the parabolic rate law w2 = kPt + constant. In others,3,4 the cubic rate law w3 = kot + constant, showed better agreement. The most recent data of Gulbransen and Andrew4 indicate that the choice between the parabolic and cubic laws for empirical representation of the data will often be arbitrary. This is particularly true if the first few minutes of the reaction with a clean zirconium surface is attributed to a different oxidation mechanism, for deviations from either rate law were found primarily during the initial period. Thus, the kinetics of this reaction have been too uncertain to permit safe extrapolation to oxidation periods of practical interest (many hundreds of hours). The data to be described are of interest, for they indicate that the cubic rate law applies over long oxidation times. The reaction of zirconium with oxygen at 1 atm pressure was followed at 350" and 450°C for 500 and 200 hr, respectively. Abraded test specimens of pure zirconium sheet&apos; 3.0 X 2.0 X 0.012 cm in size were oxidized by the procedure previously described,3 which included periodic cooling to room temperature for weighing. The surfaces were polished to a 4/0 finish using polishing paper wet with kerosene, then wiped with petroleum ether and washed in redistilled acetone. Fig. 1 shows plots of log ? vs log t. Each curve represents the average of duplicate measurements, and deviations from the average were generally less than 3 pet. The cubic rate law (slope = 1/3) is closely followed. The rate constants, 5.2, x 10 -6 and 2.4, X 10- (mg cm-2)3 per hr at 350" and 450 oC, respectively, are plotted as log k, vs 1/T in Fig. 2, together with cubic constants calculated from the data of Gulbransen and Andrew4 for abraded specimens from the same lot of zirconium. Their data refer to runs of 6-hr duration at a pressure of 0.1 atm 0 and under conditions of uninterrupted heating. In spite of these differences, the latter data yield a straight line which appears to apply equally well to the new extended time data. The energy of activation for the oxidation process, calculated from the slope of this line, i.s 38 keal per mole. This may be compared with the value of 47 keal per mole found by Belle and Mallett3 at higher temperatures. It may be concluded tentatively that extrapolation of short-term oxidation data for zirconium to obtain the long-term behavior is best done through the cubic equation ?3 = kpt + constant. References &apos; E. A. Gulbransen and K. F. Andrew: AIME Trans., 1949, vol. 185, p. A.515; JouRNal OF Metals, August 1949. &apos;D.p. Cubicciotti Journal Amer Chemical August1949.Soc., 1950, Vol. 72, P. 3 V. Belle and M. W. Mallett: Joulnal Electro chemical Soc., 1954, &apos; E. A. Gulbransen 339.and K. F. Andrew: Oxidation of Zirconium Between 400" Gulbransenand 800&apos;C.and AIME Trarzs.. 1957, vol. 209, p. 394; JOUR-Nal of Metals, April 1957. IS Barnartt, B G. Charles, and E. A. Gulbransen: Oxidation of 50 weight pet uranium-zirconium alloy, Journul Electrochemical SOC., 1957, vol. 104, p. 218.

Jan 1, 1959

By Paul Rhedey

Various commercial pelroleum cokes were heat-1,reated at temperatures between 500° and 1500°C, in a nitrogen atmosphere, in laboratovy induction furnaces. The rate of tenlperature rise was varied betzveen 10" and 300°C per min, or the green cokes were flash-calcined, orv a combination of heating rates was used. Changes in the rate of heating had only negligible effects on the degree of&apos; calcination as characterized by mean crystallite thickness and the chemical properties of the calcined coke. The physical structure of the cake was however significantly affected when rate of heating during calcination exceeded 50°C per min over the temperature range of 600° to 900°C. Surface-accessible porosily increased with the .rate of temperature rise, and this was accompanied by a change in pore size distribution. Source and properties of the green coke also had an influence on the structure of the calcined coke. The evidence presented suggests a similar mechanism of porosity development in petroleuiiz coke during calcination in industvial equiplnenl, such as rotary kilns. An increase in surface accessible povosity incveased the pitch binder requirement when the coke was used as aggregate in Soderberg paste. A correlation was established between calcined coke porosity and paste binder requiremenl. ManY results have been published on the changes of properties of petroleum coke during calcination, such as chemical composition, real density, electrical resistivity, crystallite and pore structure. The correlation of these properties with temperature of calcination and time at maximum temperature has been rather well established in both laboratory and pilot plant experiments. Surprisingly little attention has been given however to the effect of calcination conditions, such as rate of temperature rise or furnace atmosphere, on the chemical and structural properties of the calcined coke. It has been observed that petroleum coke, when calcined in industrial equipment, acquires higher porosity and lower real density than those attainable in laboratory furnaces at apparently identical calcina- tion temperature and soaking time. This paper describes a study of the effect of rate of heating during calcination on calcined coke properties using green petroleum cokes of different volatile matter, hydrogen, and sulfur content. An attempt was made to correlate the changes in coke structure with the flowability of anode paste of the type normally used in aluminum reduction cells. EXPERIMENTAL Petroleum Cokes Used. In the study of release of volatile matter and sulfur during calcination and the effect of rate of heating on calcined coke properties two delayed cokes of different sulfur contents were used. The results of analysis of the green cokes are given in Table I. In the study of the effect of flash calcination thirty-six commercial petroleum cokes from twelve different refineries were used with a range of properties shown in Table 11. Calcination Conditions. Calcination experiments were carried out in a laboratory induction furnace. In each run a 200-g sample of dry green coke sized to 10 by 65 Tyler mesh was calcined in a graphite crucible. The crucible containing the sample was placed in the middle of a stack of eight others filled with metallurgical coke to reduce temperature gradients within the sample. Temperature was measured by two Pt, Pt-10 pct Rh thermocouples and controlled by a Celectray instrument. The two couples generally agreed within 5°C. In the study of volatile matter and sulfur release the samples were heated to temperatures in the range of 500" to 1500°C at a rate of 10°C per min in a nitrogen atmosphere and held at the final temperatures for 30 min. In the study of the effect of heating rate on calcined coke properties the desired rates between 10&apos; and 300°C per min were obtained by manually adjusting the power input. Flash calcination was carried out by dropping 100 g of the green coke into the graphite dish preheated to the calcination temperature. Because of the small heat capacity of the furnace the coke was introduced in 20-g portions at a time. For this purpose a 2-in.-long nipple between two 1-in. gate valves installed on the top flange of the furnace served to provide a gas seal while feeding coke to the furnace. It was estimated that the temperature of the coke reached that of the furnace at a rate of approximately 1000°C per min. Holding time at final temperature was also 30 min. Calcined Coke Proper- Determined. Porosity was determined on 20 by 35 Tyler mesh samples using an Aminco-Winslow mercury pressure porosimeter with an operating range of 1.8 to 3000 psi absolute pressure (100 to 0.05 p pore diameter range).&apos; Apparent density was obtained by the mercury poro-simeter. It represents a particle density of the 20 by

Jan 1, 1968

By M. Kitada, U. Kawabe, F. Ishida, T. Doi

The relations between micros tructures and critical current density in transverse magnetic field were experimentally investigated due to each transformation of the 0 to 0&apos; + P" phases at 700&apos; C for superconductmainly examined using replication electron microscopy. The ß&apos; or a precipitates were found to pin down magnetic flux lines in these alloys. The effects of precipitation upon the critical current density were discussed in relation with the size, spacing, and characler of these precipitates. HIGH magnetic field superconductors, such as Nb-Zr, Nb-Ti, and Nb-Zr-Ti alloys, have been recently put to extensive practical use as winding materials for superconducting magnets.13 The critical current density of these hard superconductors under an applied magnetic field is an important characteristic for magnet materials and is very sensitive to metallurgical structure. It is generally known that the critical current density is increased by introducing dislocations and precipitates into a superconductor; that is, dislocations and precipitates are presumed to be barriers that hinder quantized flux lines from moving.4&apos;5 Theoretical6&apos;7 and experimental analyses of the motion of flux lines and the interaction between flux lines and various defects have already been reported by many authors. Metallographic analysis of high magnetic field superconductors such as Nb-Zr and Nb-Ti is difficult, so that no quantitative relationship between microstruc-ture and critical current density has been established yet. In this paper, the effect of precipitation on the critical current density in magnetic field was investigated for two superconducting alloys, Nb-40Zr-10Ti and Nb-5Zr-60Ti. In these alloys the resistive critical field H, at 4.2oK was about 100 kG and the critical current density Jc at 80 kG was of the order of 104 amp per sq cm.13-l5 The superconducting properties were examined in relation to the microstructural changes due to transformation of i) the ß to ß&apos; + ß" phases at 700°C for Nb-40Zr-10Ti alloy and ii) the ß to a + ß phases at 500°C for Nb-5Zr-6OTi alloy. The effect of size, spacing, and character of precipitates on flux line pinning was in particular examined. The microstructures were studied by means of residual resistivity, microhardness, and tensile strength measurements as well as by X-ray diffraction, optical, and replication electron microscopies. I) EXPERIMENTAL PROCEDURE Pure niobium, zirconium, and titanium, in the form of rods 0.8 cm in diam, served as raw materials. Results of chemical analyses of these rods are given in Table I. Ingots of the alloys, 0.4 cm in diam and 3 cm in length, were prepared by means of levitation melting, utilizing a copper mold in an argon-gas atmosphere. Samples from the ingot then were cold-worked by grooved mill to 0.2 cm in diam, heat-treated homogeneously (in the ß phase region) for 5 hr at 1100° in a vacuum of 1 x 106 Torr, and finally cold-drawn to 0.025 cm in diam. For heat treatments, samples were wrapped in niobium foil and sealed in an argon-gas atmosphere in fused quartz capsules. Water quenching was done after each heat treatment. Subsequently H-J, were performed at 4.2° by slowly transporting the current through the samples 4 cm long, under transverse magnetic field, until the least detectable resistive terminal voltage was observed. The resistive critical field H, was taken as the field at which 100 pv appeared at 4.2°K across a sample 3 cm in length, with a current of 5 ma. The critical temperature T, was measured by means of a conventional four-probe resistivity technique and taken as the temperature at which the sample resistance reached one-half of full restoration of the normal-state resistance with a current l ma flowing through a sample 2 cm in length. Precipitates were observed by means of optical microscopy and carbon replication electron microscopy. The etching solution consisted of 5 ml HF, 10 ml H2SO4 10 ml H2O2, and 50 ml H2O, and shadowed carbon replicas were examined in a itachi HU-11 electron microscope operated at 50 kv. X-ray diffraction photographs were taken by a 11.46-cm-diam Debye-Scher-rer camera using copper Ka radiation. The micro-hardness was measured under a load of 200 g using

Jan 1, 1969

By J. Alfred Berger, O. M. Katz

The Zv-Hf-H ternary system was studied between 500° and 900°C at pressures less than 1 atm of hydrogen gas between 1 and 60 at. pct H. A new and unique microgravimentric apparatus was used. Cizanges of slope on pressure-hydrogen composition isothernis delineated phase boundaries. These boundaries separatecl the three regions, a, 0, and y—so designated to correspond to the regions of the Zr-H binary system—from the multiphased areas between them. A eutectoidal decomposition was found with the ß region phase or phases decornposing into a lamellar product on quenching to rool ter,zperatuve. Reproducible decomposition-pressure hysteresis occilrved lnainly at lower hydrogen cornpositions and at lower temperatures across multiplzase vegions between a and 0 and a and y. Tire effects of hqfniur7z on the hydriding charactevistics of zirconiurrz weYe as follows: 1) stabilization of the a and y vegions while destabilizing the 0 region; 2) a/?preciable elevation of the decomposition pressrkres in the multiphase region between the a and /3 field; 3) ~nouenzent of the eutectoid reaction to high te~nperatures; 4) reduction in the total qiiantity of hydrogen absorbed under one atmospheve of Hz p7-essure; and 5) introduction of a split deconzposilion at the eiitectoiclal poinl in pa?? of the ternavy. Assuru~ptions based on an ir-2terstitial vandonl-solulion rtioclel 0.f hydrogen in metals slzowed that the bindit~g energy between solute sites prednnzinatecl at low /i?!dvogen concentrations. However, at high hydrogen contents the entropy was the predorninatlt factor in determining the stability of the Zr-Hf-H al1o.s. This was interpreted to mean a scarcity of filrtlzer itltevslilinl solute sites caused by hydrogen-hydvogen intet-actions in the metal lattice. INTEREST in the reaction of hydrogen with metals has increased in the past few years for the following reasons: 1) the formation or use of high hydrogen potential environments in nuclear reactors; 2) the reaction of hydrogen with alloys in nuclear reactors with the accompanying deleterious effects on the mechanical and corrosion properties; 3) the theoretical implications of thermodynamic data on the theory and rules of alloy formation in the metal-hydrogen systems; 4) the use of hydrogen-containing fuels in rocket engines; 5) the need for a process of making fine metal powders of high-melting reactive metals; and 6) the beneficial impregnation of superconducting alloys with hydrogen. In nuclear pressurized-water reactors, the problem exists of limiting the hydrogen pickup of zirconium alloys which are utilized as fuel cladding, heat shields, and support members. In general, zirconium alloys have good mechanical and corrosion-resistant properties in high-temperature water. However, hydrogen is absorbed from the corrosion reaction between metal and water, greatly accelerating the formation of the corrosion product ZrOz as well as mechanically embrittling the underlying metal. In addition, recent observations1 at zirconium to hafnium welds showed that secondary elements in zirconium can have an appreciable, and somewhat unexpected, effect on hydrogen absorption. This paper lists the thermochemical data in the range 500" to 900°C for the equilibrium reaction of four high-purity Zr-Hf alloys with hydrogen. Phase boundaries and thermodynamic functions are determined while the structural data will be presented in a future paper. In general, the Zr-Hf-H system approximates the well-known, eutectoidal, Zr-H diagram2,3 with modifications introduced through the behavior of hafnium.4,5 The Hf-H system,&apos; published while this work was in progress, provided a consistent trend with the Zr-Hf-H data. PREPARATION OF Zr-Hf ALLOYS Table I presents a complete flow chart of the preparation procedure. The zirconium and hafnium crystal bars were completely immersed in high-purity kerosene and slowly cut into thin wafers. Wafers were then cold-sheared into approximately 1-g pieces, thoroughly cleaned, weighed, and inserted into the furnace. The alloys, B-2, B-4, B-6, and B-8, were then nonconsumable arc-melted under 500 mm of purified argon. Additional purification of the argon was accomplished by melting a large titanium button each time an alloy was re-melted or a different alloy melted. Each alloy button, which weighed 25 g, was remelted four times in an approach to complete homogeneity. Material losses were less than 0.02 wt pct. Alloy buttons were alternately cold-rolled and vacuum-annealed into 10- and 20-mil sheets. Table I1 gives the composition of the four alloys used. Very little elemental segregation existed be-

Jan 1, 1965

Membership at the end of the year 1951 was 19,711 including 2228 Student Associates. The data in the third column include these Student Associates. 1. This includes all the cash dues income received from new and old members of all grades. 2. All cash initiation fees received. 3. Net income received from advertising in the three journals. The figure was $72,273, for MINING ENGINEERING; $39,844 for the JOURNAL OF METALS; and $31,564 for the JOURNAL OF PETROLEUM TECHNOLOGY. Income in 1950 was $54,572, $30,390, and $18,443 from these sources, respectively. 4. Receipts from individual sales, nonmember subscriptions, and multiple subscriptions of members. 5. Includes Transactions volumes and the Petroleum Statistics volume. 6. Sales of all other printed matter except special volumes sponsored by certain Funds. Includes a considerable sale of preprints and reprints of technical papers. 7. Does not include dividends and interest from certain Funds whose income reverts to those Funds. 8. Miscellaneous income not included in any of the above categories. 9. The total income compares with $493,197 -in 1950, an increase of $29000.

Jan 1, 1952

By A. Muan

Liquidus data are presented for mixtures in the ternary system FeO-Fe2O3-SiO2 in equilibrium with a gas phase with O2 pressures ranging from 10-10.9 to 1 atm. Data obtained are combined with previously published data to construct lines of equal 02 pressures and lines of equal CO2/H2 mixing ratios along the liquidus surface. Courses of crystallization of selected mixtures under conditions of constant total composition, constant O2 pressures, and constant CO2/H2 mixing ratios are discussed. PHASE equilibrium studies of silicate systems where iron is one component are complicated by the fact that iron readily occurs in three different states of oxidation: Fe3+, Fe2+, and Fe0. Success or failure in work with iron silicate systems is to a large extent dependent on control of the oxidation state of iron and all investigations therefore must be carried out under carefully controlled atmospheric conditions. Silicate systems containing only strongly electropositive metals (like Na+, Ca2+, Mg", etc.) can, for simplicity, be treated as condensed systems, that is, the gas phase can be neglected and the phase relationships discussed in terms of the phase rule written in the well known simplified form P + F = C + 1. In the case of iron silicate systems, however, the composition of the condensed phases varies with the gas composition, and a complete picture of phase relationships can be obtained only by varying the gas composition over a wide range. In order to understand the phase relationships in the more complicated multicomponent silicate systems with iron oxide as one of the constituents, a knowledge of the ternary system FeO-Fe2O3-SiO2 is essential, since it constitutes a bounding portion of all such systems. It was with this in mind that the present study was undertaken. Previous Work A considerable amount of work has been done on various aspects of the chemistry and metallurgy of systems containing silica and iron oxides. The two bounding binary systems FeO-Fe2O3 and FeO-SiO2" The first attempt to obtain information on phase relationships of iron oxide-SiO, mixtures at different 0, pressures was made by Greig.&apos; Darken" determined the melting points of iron oxide on solid silica under various atmospheric conditions. Darken did not determine experimentally the composition of the melts at liquidus temperatures but discussed very ably the principles involved in applying the phase rule to the system. In a recent study Schuhmann, Powell, and Michal8 determined experimentally the liquidus surface of a portion of the ternary system and combined the new information with data in the literature to construct a phase diagram. Their method was briefly as follows: Homogeneous mixtures with various contents of SiO2, FeO, and Fe2O3 were made up by melting together stock mixtures in various proportions. Samples of the homogeneous mixtures, the compositions of which were determined by chemical analysis, were then heated in platinum crucibles in an inert atmosphere until equilibrium among the condensed phases was achieved. The samples were quenched to room temperature and the phases present determined by microscopic examination. Assuming that no change in composition takes place during the equilibration run in inert atmosphere, the liquidus surface can be determined, but no information is obtained regarding the partial pressures of 0, of the gas phase in equilibrium with the condensed phases. The author&apos;s method, to be described in the next section, permitted the location of points at the liquidus surface as well as a calculation of the corresponding partial pressures of O2. Experimental Method General Procedure: The standard quenching technique was adapted for a study under controlled variable atmospheric conditions. Premelted mixtures of silica and iron oxides in platinum envelopes were held at constant temperature under chosen atmospheric conditions until equilibrium was reached among solid, liquid, and gas phases. The sample was then quenched to room temperature, the phases present identified, and, for the most significant runs, the composition was determined by chemical analysis. The corresponding partial pressure of 0, was calculated from known equilibrium constants of the gas reactions occuring in the furnace atmosphere. Materials: Starting materials were oxides of commercially highest available purity; cp silicic acid was dehydrated by heating to 1350°C for 6 hr and cp Fe2O3 was dried at 400° C for the same length of time. Samples of 10 g were made up by mixing

Jan 1, 1956

By S. T. Wlodek

The surface and subscale oxidation reactions were followed by means of continuous weight-gain and metallographic techniques over the range 1600" to 2200°F (871° to 1204 °C) for up to 400 hr. Full identification of all scale and subscale reaction products was obtained by electron and X-ray diffraction. At or below 1800°F (982°C) a linear rate of reaction (QL = 46.0 kcal per mole) governed the oxidation process, extending for up to 100 hr at 1600°F (871 "C). During linear oxidation the surface scale consisted of an amorphous SiO2 film overgrown with Cr 2O 3 and NiCr204. This initial linear process was followed, and above 1800°F completely replaced, by two successive parabolic rate laws (Qp = 60 and 57 kcal per mole). This parabolic reaction involved the formation of a complex scale consisting of Cr2 O3 and smaller amounts of NiCr2O4. Parabolic oxidation appeared to coincide with the disruplion of the silica film present during linear oxidation and was followed by subscale (internal) oxidation of crystobalite and NiCr2O4. The balance between the subscale and surface oxidation reactions controls the oxidation of this commercial alloy. The amorphous silica film appears to result in the linear rate and diffusion through Cr2O3 is the more likely rate-limiting step during parabolic oxidation. THE oxidation of a multicomponent composition is a complex phenomenon not presently amenable to a rigorous classical interpretation. Nevertheless, even a qualitative understanding of the scaling and subscale reactions that occur in a commercial composition can illuminate the reactions that limit its high-temperature stability in an oxidizing environment. This study of the oxidation of Hastelloy Alloy X presents the first of a series of studies with the above approach in mind. Hastelloy X exhibits one of the best combinations of strength and oxidation resistance available in a wrought, solution-strengthened, nickel-base alloy. Although during long time exposure some precipitation of M6C and M23C8 carbides as well as a complex Laves phase occurs, the amounts are probably small enough to have no appreciable effect on the chemistry of the matrix. Radavich has identified the oxidation products on Hastelloy X oxidized for 5 min to 10 hr at 1115°F as NiO and the NiCr2O4 spinel. Oxidation for 5 to 15 min at 1500°F produced a scale of spinel, NiO, and a rhombohedra1 phase, probably Cr2Os. Sannier et 2. have reported continuous weight-gain data for Hastelloy X at 1650" and 2010°F and internal-oxidation measurements after 150 hr at 2010°F. In addition, much of the data on binary Ni-Cr alloys recently reviewed by Kubaschewski and okins&apos; and Ignatov and Shamgunova4 as well as studies of binary Ni-Mo alloys5 are also pertinent to the oxidation of this composition. EXPERIMENTAL Continuous weight-gain measurements and metallographic measurements of subscale reactions were the main experimental techniques used in this study. X-ray and electron diffraction backed up by a limited amount of electron-microprobe analysis served to characterize the nature of the scale- and subscale-reaction products. Two heats of commercial sheet of the composition given in Table I and identified as A and B were used in the bulk of this study. Internal-oxidation measurements were made on a third heat of material in the form of a 0.5-in.-diam bar. In order to assure homogeneity, all heats were reannealed 4 hr at 2175°F prior to sample preparation. weight-Gain Measurement. All specimens (1.5 by 0.4 by 0.03 in.) were abraded through 600 paper, electropolished, and lightly etched in an alcohol-10 pct HCl solution. An electrolyte of 150 cu cm H,O, 500 cu cm HsPO4 (85 pct conc), and 3 g CrO3 at a current density of 0.9 amp per sq cm or a solution of 10 pct HaW4 in alcohol used at 4 v and 0.3 amp per sq cm was used for electropolishing. The resultant surface exhibited a finish of 3 ± 1 p rms. Continuous weight-gain tests were made at 1600°, 1700°, 1800°, 1900°, 2000", and 2200°F on auer&apos; type balances capable of recording a total weight change of 110 mg with an accuracy of k0.1 mg. All tests were made in air dried to a dew point of -70°F and metered into the 2-in.-diam reaction

Jan 1, 1964

By Keats, J. L.

IN THE literature on the elimination of metalloids in basic open-hearth practice, there are a great many heats recorded in which excellent data on changes in slag and metal composition during refining are given, but in almost all of these heats either temperature data or weights and analysis of charge are unrecorded and observations on the physical charac- teristics of the slag are almost always lacking. With these points in mind, a test heat was made in which as complete as data possible on all the factors that affect the elimination of metalloids were obtained.

Jan 1, 1957

By D. W. Frommer

Processing nonmagnetic taconites by selective flocculation-desliming and flotation requires large volumes of water. If impounded without treatment the effluents from these processes require excessively large areas for containment. Experiments conducted in the Bureau of Mines 900-lb-per hr pilot plant at the Twin Cities Metallurgy Research Center indicates that approximately 85% of the water needed to process Michigan nonmagnetic taconite could be reclaimed from the process itself. Water was reclaimed by the controlled addition of lime, sodium carbonate, and synthetic flocculant. As a result, turbidities were reduced to ?1000 ppm equivalent SiO2, while a Ca ion content of ?16 ppm was maintained in the finished effluent. Good-quality flotation concentrates were obtained with reclaimed water and, by means of some indirect comparisons, it can be concluded that the reuse of the water permits a savings of almost 2.0 lb per ton of NaOH, and probably as much as 0.25 lb per ton of fatty acid for total savings of 7.8-10.3 cents per ton of feed. These savings are nearly offset by an estimated chemical cost of 9.3[c] per ton for water treatment.

Jan 1, 1970

By Harold M. Feder, Robert V. Schablaske, Irving Johnson, Ewald Veleckis

The stoichiometry, structure, and stability of the internzediate phases formed between zinc and some of the rare earth (RE) metals were systematically exarnined by means of a recording effusion balance and X-ray diffraction analyses. In the La-, Ce-, PY-, Nd-, and Y-Zu systems, at or below about 600 C, the following sequences of phases (REZnx) were found: La, x = 1, 2, 4.0, 5.25, 7.3, 17/2, 11, and 13.0;&apos; Ce, x = 1, 2, 3, 11/3, 4.3, 5.25, 7.0, 17/2,* and 11; Pr,x = 1,2, 3, 11/3 ,* 4.3, 5.3(?), 7.0, 17/2,* and 11; Nd,x = 1,2, 3,* 11/3,* 4.3, 6.5, 8.5,* and 11; Y,x = 1,2,3, 11/3, 4.5, 5.0, 17/2,* and 12.* The structure types of all these phases were classified. In addition, lattice parameters were obtained for the first time for the pluses denoted by asterisks. In the absence of de tectable valency or electronegativity effects the systesnatic trends in the results have been ascribed to the effects of&apos; the lanthanide contraction. For example, the maximum number of zinc atoms in the coordination polyhedron surrounding the RE atom decreases from twenty-four to twenty-two to twenty as the size of the RE atom decreases. THE structures and compositions of a great many intermetallic phases (e.g., the Laves phases) are known to be based primarily, but not exclusively, on the space-filling efficiency of various modes of packing together atoms of different sizes. The valencies and electronegativities of the constituent atoms are, however, also influential. In extreme cases hypothetical intermetallic phases which fulfill the efficient spacefilling requirements may not be present in the constitutional diagram because of thermodynamic instability brought about by the operation of valency or electronegativity factors. Hence, for a detailed study of the influence of atomic size on alloy structure and composition, it would be desirable to minimize variations of valency and electronegativity. The intermetallic phases formed by the rave earths (RE) with some common partner offer an excellent opportunity for isolating the effects of size from those of valency and electronegativity. The rare earths exhibit a large, but smooth, decrease in size (the lanthanide contraction) in the series from lanthanum to lutetium when inter comparison is made for a common valence state, e.g., isolated atoms or trivalent ions. The elements yttrium and scandium are frequently included as pseudo rare earths; their sizes place them in the vicinity of dysprosium and lutetium, respectively. The electronegativities of RE elements vary by less than 10 pet. The trivalent state is the most common; however, the well-known tendency of cerium, praseodymium, and terbium to achieve higher valencies, and of samarium, europium, and ytterbium to seek lower valencies, requires that caution be exercised in the assumption of equal valencies. In the present study the existence, constitution, and structure of each of the numerous intermediate phases formed by zinc with lanthanum, cerium, praseodymium, neodymium, or yttrium were examined systematically and in detail. The investigation was conducted by a recording effusion balance technique and by X-ray diffraction analysis. The results enrich our knowledge of the phase diagrams of these systems. In addition, they present some clear-cut evidences of the operation of the size factor alone. EXPERIMENTAL PROCEDURE Apparatus. The mode of operation of the recording effusion balance and its application to phase studies have been discussed in detail elsewhere.&apos; In this work, an effusion cell containing a finely divided alloy was suspended within an evacuated tube from the beam of an analytical balance. The tube was immersed in a massive molten salt bath whose temperature was controlled to within 0.5o C during each experiment. The loss in weight of the alloy owing to effusion of zinc* was continuously recorded. Two effusion cells, 1/2 in. diam by 1 in. high, were machined from tantalum rods. Two orifices were drilled laterally into the walls of each cell. The orifice areas were determined by calibration with pure zinc: cell A had a total orifice area of 6.5 x 10-41 sq cm, and cell B an orifice area of 9.8 x 10-3 sq cm. By appropriate choices of orifice area and temperature the wide range of volatilities from pure zinc to pure rare earth metal could be investigated. X-ray diffraction powder photographs were made at room temperature with a 114.6-mm Debye-Scherrer camera with both filtered CuKa radiation and filtered CrKa radiation. Lattice parameters were refined by a computer-programmed least-squares analytical treatment which incorporated appropriate extrapolation techniques.2 Frequent use was also made of a special computer program3 designed to generate a powder pattern from an assumed structure in order to verify structural assignments. Materials. Lanthanum, neodymium, and yttrium were purchased from the Lunex Co., cerium from the Cerium Metals Corp., and praseodymium from the St.

Jan 1, 1968

By J. A. Barr, R. B. Burt, I. S. Tillotson

DISCUSSION Howard Howie (Knoxville, Term.)—The authors are to be congratulated on the presentation of a paper containing so much valuable information on the pipeline transportation of phosphate, as there is very little literature on the subject. The writer is especially interested in the paper, as he conceived the arrangement of the Akin and Godwin plants and was in charge of the design work and the engineering incident to their construction. The Akin and other phosphate deposits in the Tennessee phosphate area lie on beds of limestone that are very irregular. The limestone beds, after the phosphate matrix has been removed, are similar in appearance to land severely eroded by the action of water and denuded of top soil. Depressions in the limestone, called cutters, are irregular in depth with vertical or overhanging walls, having the general appearance of cracks in dried clay. They change abruptly in direction, width, and depth, and vary on the Akin tract from 1 to 25 ft in depth and from 1 to 50 ft in width. Pinnacles of limestone commonly occur in the cutters which appear, when exposed, like small clifflike islands in a river. Limestone floats also occur. The phosphate matrix fills the cutters and covers the uncuttered areas, the thickness of the cover varying continually and sometimes rather abruptly. It occurs generally as stratifications of phosphate rock and clay of varying thickness. The phosphate rock in the matrix varies in hardness and in percents of silica, lime, iron oxides, and fluorine, and the clay varies in toughness. In some places the deposit consists of narrow strata of rock almost devoid of clay streaks. In other nearby locations the clay will predominate. When it is excavated, the phosphate rock breaks into thin irregular lumps, locally known as plate rock. Limestone lumps are also excavated with the matrix. Akin plate rock is generally much softer than that occurring in other deposits in the area. Because of the above described physical and chemical variations of the excavated material, the resultant slurry varies in size distribution, specific gravity, and percent of slimes. When the rock is soft or when there is an increase of clay, the slime fraction is greatly increased as it passes through pumps and pipelines, resulting in reduced pipe friction. It is obvious that the longer the pipeline the greater the reduction of coarse fractions into fines, causing a decrease in pipe friction that cannot be accurately evaluated. The matrix is mined with a dragline that drops it into a hopper with a grid composed of 9-in. parallel bar spacings located above the hammer mill. The matrix on, and passing through the grid, is subject to the action of powerful sprays which wash it down to the hammer mill, together with any limestone lumps that are not removed before passing through the grid. The hammer mill reduces the feed to lumps of plate rock and clay, most of which will pass through the 8-in. pump suction. The mixture discharges into a pool containing the pump suction pipe. Water from a hydraulic nozzle moves the mixture to the pump suction intake. The pump, driven by a variable speed motor, is the same size as the pumps mentioned on p. 279. Provision is made to remove any lumps that lodge in a bend in the suction pipe in a manner similar to that used in the Florida phosphate fields. The hammer mill and pump units are mounted on wide steel skids so that they can be moved as the mining operation progresses. The discharge from the pump flows through an abrasion-resistant spiral welded steel pipe 81/4 in. actual inside diam, 8 in. nominal diam, for a maximum distance of 2200 ft, which is the limiting pumping distance for one pump. This pipeline, referred to hereafter as pipeline A, discharges into a ball mill without balls, which in turn discharges into a rotary screen attached to it that separates the slurried matrix into 11/4-in. oversize and undersize fractions. The oversize is returned to the mill for further reduction; the undersize is pumped to a Dorrco washer and then flows into a hydroseparator 160 ft in diam. In spite of the size reduction in the hammer mill and the blunging and washing of the slurry in its passage through the pump, pipeline, mill, and washer, the discharge to the hydroseparator frequently contains mud balls almost perfectly spherical. Sometimes the discharge from the 16,000-ft pipeline at Godwin contains mud balls the size of bird shot and smaller. This pipeline will be referred to subsequently as line B. Liquid caustic is added to the slurry at the Akin plant before its passage through the hydro-separator, which decreases the size of particles in the overflow by dispersion. In passing through pumps 1, 2, and 3 and pipeline B, the slime fraction in the underflow is increased by abrasion and blunging and also by continuing dispersive action of the caustic. The matrix for use in the experimental tests referred to on p. 279 was obtained from three small surface openings on the Akin tract that were made previous to the purchase of the tract by the Authority. Matrix used in the 2 and 4-in. experimental pipeline tests was taken from the three openings and proportioned to obtain a sufficient quantity that would be fairly representative of the average in the Akin deposits. Prospecting samples of matrix had been obtained from drill holes which showed no small variation in physical and chemical properties. Some of the physical variation is evident from the size distribution of solids in samples taken during the tests covering line B flows so thoroughly made by the Authority und&apos;er the direction of Mr. Burt, see Table V, p. 280. Hydraulic gradients for a pipe of 8-in. diam were derived from the 2 and 4-in. pipeline tests using the so-called representative matrix as above described, and plotted on the profile of pipeline B. Gradients of other materials in slurry form passing through pipelines that bore some similiarity to the Akin matrix slurry were also plotted. After a study had been made of the hydraulic gradients plotted on the profile and the varying slurry flow that would probably occur during actual operation, three pumps were ordered, referred to as No. 1, 2, and 3 on p. 279. No. 1 and 2 pumps were installed and the third kept in reserve should the operation of 1 and 2 pumps prove satisfactory, since installation of the third pump would require an attendant, as well as the laying of 5400 ft of pipe to supply it with seal-water from the Akin plant. Subsequently, it was found desirable to install the third pump to maintain capacity when the slime fraction was low and the coarse fractions were large. Reference to Fig. 6 will show that the flow in B line goes upgrade in three locations. At the outlet at Godwin, the slurry flows between two 45" bends for an approximate distance of 18 ft to rise above the ground a sufficient height to discharge into a launder feeding the first classifier. This condition requires extra energy, which is taken care of by keeping the hydraulic gradient a sufficient distance above the high points. Although there are rather heavy upgrades in the line, the choking condition that might occur at the

Jan 1, 1953