Search Documents

By Daniel Bloomfield

ONE of the major problems of management is how to restore in some measure the personal relation-ship between employer and employed which, in the days of small concerns, meant better morale among employees. The complexity of industry today, the heterogeneous mass. of workers employed, many .of them new to this country and to its institutions, the inability of those whose task it is to get out production to spend much time on the problems of labor-all these and many other factors serve to make of great impor-tance the question of how to establish more satisfactory mutual good will. While there is no such thing as a sure cure for labor troubles, in spite of the fact that charlatans have been selling alleged cures to guileless employers, study and experience have brought to light methods of approach to the problems confronting management in its relation to labor that are well worth consideration. Labor problems must be approached with common sense and an open mind. Facts must be the basis of action. So it is with the question of morale in industry. What makes or breaks morale? What are the forces behind the actions of men? What is there in one man that makes him act differently from another man under similar circumstances? How are men affected by the actions of others in their own group or by the actions of those under whose supervision they work? These are questions that must be carefully studied if we are, to get at the bottom of industrial unrest. It is an easy thing to say that good will can be created by "treating men right." That involves so many things and points of view that it will hardly serve as a full answer to our problem; but it is a good starting point if we mean by right treatment the payment of wages consistent with the well being of the worker and his family as members of the community, and if we also mean the provision of sanitary, wholesome working conditions and a working schedule that does not overtax the worker physically, and mutuality-a give and take relationship. With this as a basis we can go a step farther and see what else can be done to promote better relations between management and the workers.

Jan 9, 1922

By Robert G. Johnson, Richard J. Prosen

THE present work was done in connection with a program for investigating metal-to-ceramic braze techniques using the well-known reactivity of titanium with certain ceramic oxides. The investigation extended over the range of 0 to 30 pct Ti. The indium was obtained from the Indium Corp. of America and was specified to be 99.97 pct pure. The titanium was supplied by Metals Disintegrating Co. and was stated to be 99.5 pct pure. Each 2 to 4 g quantity of the alloy compositions studied was prepared using a mixture of 300 mesh powders pressed into pellet form. The pellets were heated in thin-walled molybdenum crucibles using a resistance-wound furnace in a vacuum less than 10-4 mm of Hg. Little reaction occurred between the molten alloy and the crucibles at the temperatures and short time intervals used. Only slight spectroscopic traces of molybdenum were found in the melt after a typical period of heating. The points shown on the phase diagram of Fig. 1 represent thermal arrest measurements. The phase boundaries shown are consistent with the thermal arrest and X-ray data obtained. The temperatures were determined using a Pt-Pt 10 pct Rh thermocouple with the junction spot-welded to a short molybdenum rod. The rod was almost completely immersed in the liquid metal, so that good thermal contact with the melt was achieved. The small mass of the crucible and its contents made it possible to obtain many heating and cooling curves in a few minutes time, an advantage which helped to minimize the effects of indium evaporation at the higher temperatures. A Brown strip chart recorder was used to display the thermal arrest curves. To check the technique, the melting point of 99.999 pure Al was measured and found to be within 1 of 660.2c, the accepted melting point. The upper limit of temperature with this technique was about 900°C beyond which the evaporation rate of indium became great enough to alter appreciably the alloy composition during the runs. A peritectic transition was found at 796°+ 5°C from 1.5 to 30 wt pct Ti. It was not found at 0.5 or 1.0 pct. A small super-cooling effect was observed. The melting-point transition to the B + L phase was found up to 20 pct Ti but not at 25 pct. Within the 1 deg accuracy of the measurement, the transition temperature was that of pure indium, 156°C. The liquidus line to the left of the 1.5 titanium point was located only approximately. The two crossed circle points at 1.0 and 0.5 pct Ti place a lower limit on the liquidus line and were determined by observing visually the cessation of vibrations in the melt caused by the damping effect as B-phase crystals were formed during cooling. The B-phase boundary was found at 23.8 pct Ti by X-ray analyses of small single crystals of the B phase isolated from 2 pct Ti melts. The compound was found to be Jetragonal with lattice dimensions of c = 3.052A and a = 10.094W. From the unit cell dimensions and the measured density of 6.42 i 0.05 g per cc, the compound was determined to be In4Ti3 which has 23.8 pct Ti. The calculated density of 6.44 g per cc is obtained assuming 2 mol

Jan 1, 1962

By E. E. ELLIS

THE zinc deposits under development by the Universal Exploration Co., a subsidiary of the United States Steel Corporation, are close to Jefferson City, Tenn., a small town about 30 miles northeast of Knoxville, Tenn., and are served by the Southern Railway. The first zinc mining in this district was in the old Mossy Creek mine at the north edge of the town, opened for oxidized ores in 1871 and later worked for sulfide ores. An oxidized zinc ore deposit (carbonates and silicates) was opened near New Market in 1900 and worked through the war period by the G1'8sselli Chemical Co., producing around 25,000 tons of oxidized ore. In recent years a sulfide deposit has been found and developed but is not producing. About 1% miles south of this a small body of sulfide ore was developed by open cut, but the operation was unsuccessful. The Universal Exploration Co. entered the district in 1926 and, after extensive exploration, has been operating an oxidized ore-body since Janual:y, 1928, and has been developing a sulfide ore body since July, 1928.

Jan 1, 1929

By J. F. Smith, J. E. Davison

The heat capacity of CaMg2 was measured over the temperature interval, 4.8° to 287°K, by the technique of low-temperature adiabatic calorimetry. Heat content measurements were performed with a drop calorimeter over the temperature interval, 273" to 673°K. From these data the thermodynamic functions, (FT - H0)/T, ST - So, and & - Ho, were evaluated. A third-Law calculation of the standard entropy of formation of CaMg2 yields a value of -0.25 * 0.06 cal per (°K g-atom) , and the free-energy function derived from this study when combined with existing equilibria data yields a value for the standard enthalpy of formation which is in agreement with direct calorimetric enthalpy measurements. The accompanying paper' shows that the enthalpy of formation of CaMg2 has been determined with good precision by three different calorimetric techniques.'-= TWO independent determinations of the Gibbs free energy of formation of CaMg2 have also been made; both determinations were based on vapor pressure measurements, being in one case hydrogen vapor pressures over ternary Ca-Mg-H alloys4 and in the other case magnesium vapor pressures over binary Ca-Mg alloys.5 The present determination of heat capacity of CaMg2 below room temperature and of the heat content of CaMg2 above room temperature was undertaken to provide supplementary data. These data are useful in their own right but can in addition be used to evaluate an entropy of formation for CaMg2 which, because of the interrelation of free energy, enthalpy, and entropy, can be used as a check of the self-consistency of the composite of the presently available information. LOW-TEMPERATURE HEAT CAPACITY The heat capacity of CaMg2 was measured over the temperature interval 4.87° to 286.64°K in an adiabatic calorimeter. The physical details of the calorimeter and the experimental procedure for measuring the heat capacity of a specimen have been adequately described by Gerstein et a1.6 The source and purity of the calcium and magnesium are described together with the methods of sample preparation and chemical analyses in the accompanying paper.' Results of chemical analyses of the material which was used in the present investigation are shown in Table I. These analyses show that, on the basis of the published phase diagram,7 the heat capacity sample contained a slight excess of a calcium while the heat content sample contained a slight excess of magnesium. However, in both cases the excess was small, and X-ray diffraction patterns showed reflections which were without exception attributable to CaMg2. The sample which was used for heat capacity measurements weighed 69 g while the sample container and addenda weighed 132 g. The sample was in the form of annealed powder, 50 to 60 mesh, and was sealed into the sample container under 0.1 atm of helium. Copper fins inside the sample container facilitated thermal equilibrium of the powdered Sample. Time intervals of the order of 10 min were required for thermal equilibration, and such times are normal for this calorimeter regardless of the form of the sample. The observed heat capacities were corrected for the small excess of a calcium through use of the heat capacity values tabulated by Hultgren et a1.8 The corrected heat capacities are tabulated as a function of temperature in Table II. The free-energy function and the absolute entropy of CaMg2, which were calculated from the experimental heat capacity data, are listed in Table 111. A smooth curve was fitted to a plot of the experimental values of the heat capacity and in only two instances above 30°K did the plotted points deviate from the curve by more than 0.2 pct. Below 10°K the deviation of several of the points was as much as 50 pct. These large percentage deviations were attributed to the small value of the heat capacity and to the low sensitivity of the platinum resistance thermometer in this temperature range. The deviations in the region of 10°to 30°K were less than 5 pct. Although the percentage deviations of some of the low-temperature measurements are large, the actual value of these deviations is small since the magnitude of the heat capacity in that temperature range is small. The error in the value of the third-law entropy at 298.15°K was estimated to be less than 0.01 cal per (°K g-atom). A value of -0.25 ±0.06 cal per (°K g-atom) was obtained for the standard entropy of formation at 298.15°K from the relation:

Jan 1, 1969

By H. M. Strong

Nickel and carbon form a metastable nickel-nickel carbide eutectic system which was ohsen)able by freezing latent-heat arvests at pressures 210 khars. The eutectic freezing temperature Is pressure had a slope of -0.9°Cper kbar. At 50 khars, the nickel-nickel carbide eutectic was at 1297° * 5°C and 0.34 mole fraction Ni3C. The composition of the eutectic increased at an initial rate of 0.004 mol fraction per kbar. The carbon content of the a phase also increased with pressure. Seveval illustrations of nickel carbide microstruc-tures are given and data on the lattice expansion of nickel in terms of carbon content are included. IRON, cobalt, and nickel form a variety of carbides with compositions varying between MeC and MC. Of the three, the carbides of iron are most easily recovered. The nickel carbides are so unstable at temperatures above 900°C that their occurrence in Ni-C alloys is unusual. Under sufficient pressure, however, the temperature range for the stability of the ferrous metal carbides is likely to be increased, or their decomposition suppressed (e.g., see Hilliard' on FesC), providing an opportunity to study the unstable carbides more closely. This was found to be true for nickel carbide which, under pressure, formed a eutectic with nickel. This paper describes the conditions of formation of nickel-nickel carbide eutectic compositions and their subsequent recovery. Despite the comparative instability of the nickel carbides, something is already known about them through various chemical reactions at temperatures not exceeding a few hundred degrees, and from their recovery by the very rapid quenching of molten Ni-C alloys from temperatures of about 1450°C or above. At least four carbides of nickel have been reported: A discussion of the state of knowledge about Ni3C is given by ansen.' The studies of Morrogh and williams7 who obtained Widmanstatten nickel carbide structures and of sidorenko8 who first obtained nickel carbide eutectic structures are also of interest. Sidorenko used short heating times for molten nickel in a graphite crucible followed by very rapid quenching to obtain the eutectic structures. Long heating times produced only the nickel-graphite eutectic probably due to the presence of graphite crystals in the melt which nucleated graphite crystallization. According to the early work summarized by anssen,' nickel carbide may form at temperatures far above the melting point and may be recovered by very rapid quenching. More recently, Giardini and Tydings, working on diamond synthesis, found evidence for "free nickel carbide'' in high-pressure reactions carried to temperatures far in excess of the limit for diamond growth, followed by rapid thermal quench. They stated that nickel carbide was not found in association with diamond growth. In the present work, observations were made on the melting and solidification temperatures of Ni-C alloys as a function of composition, temperature, and pressure. The nickel-nickel carbide eutectic was found at pressures above 10 kbar and its variation with pressure followed up to 60 kbar. Nickel-nickel carbide microstructures were recovered by quenching under pressure from temperatures of about 1400°C and higher. The formation of nickel carbide structures under ordinary diamond-growing conditions was usually observed but the role of carbide formation as an intermediate step in diamond growth needs more study. EXPERIMENTAL METHODS The melting and solidification temperatures of various nickel-graphite compositions were observed by latent-heat arrests in the sample holder illustrated in Fig. 1. The samples were composed of mixtures of carbonyl nickel powder and National Carbon Co.'s SP-1 graphite packed to densities of about 6.4 g per cu cm. They were contained within

Jan 1, 1965

By M. T. Hepworth, T. P. Papazoglou

Hydrogen diffusion in hcp and bcc titanium in the temperature range 610° to 900°C was measured by reacting cylindrical specimens of high-purity titanium at constant temperature with small constant pressures of hydrogen of the order of a few Torr. In the range 0 to 6.7 at. pct H in hcp titanium, the diffusion coefficient D in sq cm per sec is given by: where T is in °K and R in cal per g-atom OK. Only three measurements of diffusivity in bcc titanium were made: at 900' : the diffusivity in ß titanium was found to be 1.8 x 10-4 sq crn per sec. McQUILLAN1 has studied the constitution of the Ti-H system and reported the concentration of hydrogen as a function of pressure of hydrogen and temperature. He found hydrogen absorption was reversible and rapid at temperatures above 500°C in both crystallographic modifications, the a (hcp) phase and the ß (bcc) phase, with the latter phase stabilized by hydrogen additions. Wasilewski and Kehl 2 measured the diffusivity of hydrogen in hcp and bcc Ti-H alloys. For bcc alloys, they reacted cylindrical specimens of titanium with hydrogen gas at 1 atm pressure. They measured the rate of absorption of hydrogen isothermally on specimens ranging from zero hydrogen content when above the transformation temperature to hydrogen contents sufficient to stabilize the bcc phase when below the transformation temperature. By integrating Fick's second law for a cylindrical geometry, assuming a diffusion coefficient independent of composition, they calculated diffusivities as a function of temperature. In the range 650" to 1000°C their results in bcc titanium yielded the expression: where D is in sq cm per sec, T in OK, and R the gas constant in cal per g-atom-OK. Their studies on the hcp a phase were conducted by exposing long cylindrical titanium specimens to hydrogen at a sufficiently high pressure to establish a surface layer of fl phase 80 to 120 u thick for the duration of an isothermal experiment. Concentration profiles were then determined by hydrogen analysis from chips obtained upon machining quenched specimens. The diffusivity of hydrogen was then calculated yielding the expression: The present investigation was undertaken principally to redetermine the diffusivity data on a titanium by a direct absorption from the gas phase at sufficiently low hydrogen pressures to avoid the presence of a surface bcc phase and also to check the diffusivity data at low hydrogen concentrations in the bcc stmcture. EXPERIMENTAL PROCEDURE High-purity electrolytic sponge titanium (99.9 pct) of BHN 91 was arc-melted, forged, rolled, and machined into cylinders of final hardness, upon annealing, of BHN 92. Cylindrical specimens of two sets of dimensions were used: 1.524 by 2.931 cm and 1.905 by 3.663 cm diam and length, respectively. The experimental apparatus used for annealing specimens and for admitting known amounts of hydrogen at constant pressure is shown in Fig. 1. In a typical experiment, a specimen was lightly abraded with fine-grain silicon carbide, washed with water and detergent, and then thoroughly degreased with reagent-grade tri-chlorethylene and acetone. The specimen was suspended by a Chrome1 wire in the center of a quartz furnace tube, without contact with the tube, and heated to 925°C (as measured by a thermocouple adjacent to the specimen, outside the tube) for a period of at least 4 hr under a vacuum of from 10-6 to -7 Torr as measured by an ionization gage. The furnace temperature was then adjusted to the temperature chosen for the particular diffusion study and the specimen allowed to equilibrate thermally. Hydrogen was then ad-

Jan 1, 1969

By J. M. Smith, G. P. Willhite, J. S. Dranoff

Heat transfer rates were measured in sandstones with flow of gases perpendicular to the direction of energy transfer. Effective thermal conductivities ker ranged from 0.7 to 1.7 Btu/(br)(ft)(°F). The contribution of the solid phase appeared to be the most important in these consolidated materials, although the thermal conductivity of the gas had some effect. The velocity of the gas through the pores of the sandstones had no influence upon ker up to values of 168 lb/(br) (sq ft) in agreement with data obtained for unconsolidated beds of glass beads. The present results indicated that gas mixing, and hence heat transfer by convection in the pores, is less for perpendicular transfer of energy than when fluid flow and energy transfer are in the same direction. HEAT TRANSFER PERPENDICULAR TO FLUID FLOW IN POROUS ROCKS Heat transfer in porous media with pore sizes in the micron range depends upon the fluid in the pores and the geometry of the solid phase. The best characterized system is a bed of solid spherical particles. Heat transfer in this system has been studied extensive1y (Ref. 8 summarizes the literature up to 1959) when the pores contain stagnant fluid. When the fluid is in motion the directions of flow and energy transfer have an effect on the heat transfer rates, as demonstrated by comparing the work of Willhite, et al l3 for perpendicular flow and that of Kunii and Smith9 for parallel flow of energy and fluid. For perpendicular flow, no increase in effective thermal conductivity ke was noted up to mass velocities G of 77 lb/(hr) (sq ft). In contrast, for parallel flow ke, increased with G in the same range of flow rates. These higher values of ke in the direction of flow also have been observed3,4,10 in beds of larger particles, 0.1- to 0.5-in. diameter. For beds of consolidated materials, such as porous rocks, data are not available for these compar- isons, although Adivarahan1 reported results for the parallel case. Hence the primary objective of this work was to measure ke values for perpendicular flow of fluid and energy in porous rocks. Of interest also was the variation in effective conductivity with fluid velocity. APPARATUS AND PROCEDURE In the experimental method, a constant heat flux was applied to the inner surface of an annular section of the porous rock. By cooling the outer wall, a temperature gradient through the annular sample was established and measured with thermocouples placed within the sample at various radial positions, and at three elevations (A,B.C). The location of the 2-in. O.D., 3.75-in. long sample in the apparatus is shown in Fig. 1. Fluid entered the bottom (1) of the 3-in. I.D. (approximate) steel shell, flowed upwards through the sample and out at the top (3). pressure taps (2,4) were used to check the permeability of the sample. The energy flowed radially from the centrally-located electric heater through the sample and was absorbed in the water-cooled jacket. The samples studied were naturally occurring sandstones from different locations with the properties given in Table 1. These materials are identical with those used by Adivarahan 1 for the parallel flow of energy and fluid. Prior to use they were refluxed with toluene to remove hydrocarbons and leached with distilled water to remove soluble salts. Each sample was visually examined and discarded if large nonhomogeneities, such as cracks or stone particles, were noted. Eight copper-constantan thermocouples were inserted in holes drilled radially into the sample with

By P. M. Robinson, M. B. Bever

THE heats of formation at 273°K of the compounds InBi, In2Bi, and TIBi2 have been determined by metal solution calorimetry with bismuth as solvent. The published information on the thermody-namic properties of these compounds is limited. The structure of the compound InBi (mp, 383°K) is tetragonal of the PbO (B10) type.1 The compounds In2Bi (mp, 362°K) and TIBi2 (mp of highest-melting composition, 486°K) are now believed to have structures of the NizIn (B8) type273 and not the A1B2 (C32) structures reported earlier.4, 5 The compounds In2Bi and TIBi2 have limited homogeneity ranges at room temperature, while the compound InBi has no detectable homogeneity range.' Samples of the compounds were prepared from 99.99 pet Bi (Mallinckrodt Chemical Works), 99.999 pet in (American Smelting and Refining Co.), and 99.99 pet Tl (Amend Drug and Chemical Co.) by melting the components in sealed, evacuated Vycor tubes. The compounds InBi and in2Bi were of the stoichiometric compositions. The compound TIBi2 contained 40 pet T1; this composition was chosen because at room temperature the alloy of stoichiometric composition does not lie within the homogeneity range.' The melts were held approximately 50°C above the liquidus for 8 hr and then quenched into iced brine. The samples were homogenized for 48 hr at temperatures 20°C below the temperature of complete solidification. Metallographic examination of sections taken from the center and the ends of the ingots did not reveal second phases or segregation . The heats of formation were determined as the difference in the heat effects on solution of a compound and of a mechanical mixture of its components added from the reference temperature of 273°K to liquid bismuth at 623°K. The details of the calori-metric procedure and method of calculation have been described elsewhere? The calorimeter was calibrated by adding bismuth at 273°K to the bismuth bath at 623°K. The calculated values of the heats of formation of the compounds, listed in Table I, are based on a value of 4.96 keal per g-atom for the difference between the heat contents of bismuth at 273" and 623oK7 No published values are available for the heats of formation of the compounds InBi and In2Bi. Hultgren et a1.7 have calculated a value of -0.50 i 0.10 keal per g-atom for the heat of formation at 423°K of the compound TIBi2 containing 40 at. pet T1 from heat-content measurements in the range from 398" to 700°K and the heats of formation of the liquid alloy. The difference between this value and the value of -0.66 * 0.01 keal per g-atom at 273°K is too large to be attributed to a difference between the heat capacities of the compound and the components over the temperature range 273o to 423oK7 However, the direct determination of the heat of formation by a calorimetric method should give a more accurate value. The heats of formation at 273°K of the compounds InBi and In2Bi lie on a straight line when plotted as a function of composition, Fig. 1. The compound In2Bi, therefore, appears to be barely stable with respect to its neighboring phases. In order for the free energy vs composition curve to be concave towards the composition axis, the entropy change on formation of In2Bi must be more positive than that on formation of InBi. As the compounds are ordered,2, 3, 8 there is no configurational entropy change on formation. The difference between the entropy changes on formation of the two compounds, therefore, is probably associated with the vibrational entropies. In view of the low heats of formation, the changes in vibrational entropy, due to changes in bond strength on formation of the two compounds, are likely to be small. Owing to the volume contractions on formation of the two compounds,5 the vibrational entropies probably decrease slightly but the decrease of the vibrational entropy of InBi is expected to be larger than that of In2Bi.

Jan 1, 1965

By AIME AIME

OPPORTUNITY may not be knocking but it, at least, is waiting for you, your family and your friends in that amazing republic south of the Rio Grande. For the first time we are able to publish the official itinerary for the forth-coming Mexico City meeting of 1936. As shown on Page 351, the deluxe special train leaves St. Louis on Thursday. Nov. 5 at 5:30 p.m., returning to St. Louis on Nov. 18 at 8:15 a. m. The schedule provides seven days and six nights in Mexico City with numerous excursions to nearby towns and resorts. The oldest surviving city in' North America is Mexico City, dating back at least to the twelfth century. It was the Aztec capital when Cortez arrived in 1519. The famous cathedral still standing was built on a foundation of sculptured Indian images and the remains of a great Aztec temple. Today it is a city of romance.

Jan 1, 1936

By AIME

The following corrections (in italics and bold face) were received too late for the September issue of Transactions: Page 270, Abstract, line 1, spelling should be goethite. Page 270, column 1, authors' box, authors' affiliations should read: L. A. BAKER, formerly Principal Research Scientist, is Pellet Plant Superintendent, Cliffs Western Australian Mining, Cape Lambert, W. A., Australia. C. G. THOMAS is Experimental Officer, Minerals Research Laboratories, C.S.I.R.O., North Ryde, N.S.W., Australia. R. J. CORNELIUS and K. S. LYNCH are General Superintendent, Product and Process Development, and Superintendent, Pellet Plant, respectively, Hamersley Iron Pty. Ltd., Dampier, W. A., Australia. G. J. ARMSTRONG, formerly Chief Metallurgist, Hamersley Iron Pty. Ltd., is Mill Superintendent, Samin Ltd., Burra, S. A., Australia. Page 271, column 2, line 41, should read "highest possible spalling temperature and to adjust the. . :' Page 275, column 1, line 1, should read "(LOI) figures are shown in Table 1 and vary from 2.61..." Page 275, column 1, line 16, spelling should be goethite. Page 276, column 2, line 6, should read "Predicting Grate Speed and Production Rate: The cor-..." Page 276, column 2, line 8, should read "basis of Blends A, B, C, D, and Plant Ore 1, shown in Table..." Page 276, Table 3, heading under "Prediction Method" should read Blend E. Page 277, column 1, line 38, should read "=293 tph of specification pellets (see Table 1 for loss-..." Page 277, column 2, replace caption for Fig. 14 with the following: Fig. 14-Example of calculation of hood temperature profile during downdraft free-water drying, given plant free-water drying time. Page 277, column 2, replace caption for Fig. 15 with the following: Fig. 15-Example of calculation of hood temperature profile during drying, given plant goethite drying time.

Jan 1, 1974

By B. H. Bergstrom, Will Mitchell, T. G. Kirkland, C. L. Sollenberger

IN a previous article' the authors outlined a study of the variables in rod milling and also reported data from a series of open circuit grinding tests on a massive limestone in a 30-in. x 4-ft end peripheral discharge rod mill. As a second part of the experimental program, an analysis is now presented for the 30-in. x 4-ft overflow rod mill grinding under identical conditions, except that discharge ports on the periphery of the mill shell have been sealed so that the products from the present series overflowed through a 9-in. diam .opening in the center of the end plate. A variance analysis has been made of the combined data for the two experiments, and performances of the two mills are compared here. Included in the first report' were descriptions of feed preparation, rod mill circuit, instrumentation and controls, and techniques used to evaluate data. Dependent and independent variables were defined, and variance analyses were made to test the relative significance of variables and to establish magnitude of error for the experiment. Significant data were plotted in various combinations, and conclusions were drawn from the graphs. The procedure and analysis in this series of tests follows the first tests and is not repeated. Data from the second series are recorded in Table I. Listed in the first three columns are the independent variables of feed rate (1000, 2000, 3000, 4000, and 5000 1b per hr), mill speed (50, 60, 70, 80, and 90 pct of critical), and pulp density (50, 60, 70, and 80 pct). The dependent variables, Pso, P100, reduction ratio, slope of the log-log sieve analysis curve, power demand, and Bond work index follow. Of these, only the reduction ratio and the Bond work index were analyzed for significance. Production of new surface as calculated from sieve analyses has not been included for this series because of the questionable assumptions that have to be made to satisfy the formulas involved. The large number of products obtained during the runs precluded the use of surface measurement techniques by the gas adsorption methods at this time; however, samples of all products have been stored for future reference. To test the consistency of the reporting of the sieved products, an averaged sieve analysis was calculated from the wet-dry plots obtained from the three product samples of each run. The resulting averaged analysis was plotted and the P80, selected. The relative deviations of the P80's from each of the three product samples with respect to the P80 of the averaged analysis were then calculated. In only two sets were the relative deviations (6.2 and 9.9 pct) considered excessive. In each of these two sets, one sieve analysis was obviously out of line; hence that analysis was ignored and new averages were computed. This reduced the relative deviations to 1.2 and 2.7 pct respectively. The relative deviations of the product analyses with respect to their averages ranged from 0.1 to 1.4 pct at 1000 lb per hr, 0.0 to 1.1 pct at 2000 lb per hr, 0.2 to 3.0 pct at 3000 lb per hr, 0.3 to 4.3 pct at 4000 lb per hr, and 0.5 to 5.2 pct at 5000 lb per hr. The relative deviation of the 80 pct passing point for 96 dry sieve analyses of the feed with respect to that of the averaged analysis was 7.6 pct. This slightly higher percentage can probably be attributed to a greater proportion of tramp oversize in a crusher product than is ordinarily found in a rod mill product. The last column on Table I lists the adjusted work index, which has been used as the measure of efficiency for the various combinations of operating conditions investigated. Efficiency increases as the index becomes lower. It was reported in the previous paper that the work indexes for the Waukesha limestone used in these experiments decreased as the product size decreased (as calculated from Bond grindabilities). That is, this limestone becomes easier to grind as the material becomes finer. This is unusual, because the work index for most materials as calculated from the Bond grindability has remained constant as the product size decreased or has increased slightly. Table II lists the results of Bond grindability tests at all mesh sizes from 3 to 200 and the work indexes calculated from them. To remove this variation of work index with product size from the data so that results would apply to any material of constant work index, the work index values shown in Table II were plotted against product size on log-log paper. From this curve (a straight line function in this case), the expected work index for the product size for each of the runs of the experiment was obtained. The work indexes as calculated from the reduction ratio and energy consumption were then divided by the corresponding expected work index. The results obtained are reported in percentages on Table I as adjusted work index and are actually percentages of the work index for the Waukesha limestone at the size in question. Multiplication of the work index value for a material of constant index by these percentages should allow the application of the adjusted work index curves to the material. Only the adjusted work index values, not the actual experimental values, were used for the variance analyses and for the graphs.

Jan 1, 1956

By H. R. Page, A. E. Jr Lee

From the inception of zinc retorting on a commercial scale in the United States in 1890,' the retort employed has undergone wide variations in its composition and manufacture, facilitating in part equally remarkable improvements in furnace capacities. The early day hand made clay retort was charged with carbonates or silicates or with coarse dead roasted concentrates mixed with a large proportion of charge fuel resulting in a relatively low zinc burden and fired 24 hr in direct coal fired furnaces. Its modern counterpart is fabricated in hydraulic presses from clay mixtures containing sizeable amounts of either silicon carbide or silica flour, charged with sintered flotation concentrates to more than three times the early day zinc burden and fired 24 to 48 hr in gas fired furnaces. This paper does not attempt to describe in detail the early day clay retort practice as it is well outlined in treatises by Ingalls,2 Lodin,3 Liehig,4 Hofman5 and others. A brief review of clay retort practice is presented together with a description of the major developments since 1912. Clay Retorts The Belgian type retort, both in the circular and elliptical forms, has been used almost exclusively. Typical dimensions of press made clay retorts around 1910 are shown in Table 1. Variations in these dimensions were used at different plants according to local conditions to a maximum inside diameter of 9 in. and inside length of 54 in. However, the effective heat penetration in a 24 hr firing cycle and the tendency of the retort to bend limited the retort size. Use of the elliptical vessel was an attempt to present a stronger cross-section resisting the tendency to bend and to increase the burden without increasing the depth of heat penetration. One exception to the 48-54 in. length was the 60 in. retort used as early as 1905 at Palmerton by means of supporting the last 12 in. at the butt end with a specially designed furnace back-wall. This backwall construction with the 60 in. retort had been developed and used at Bethlehem by G. G. Con-vers and A. B. DeSaulles. An attempt was made at Blende, Colo. to use even larger retorts of the Rhenish type based on European practice and requiring much higher furnace temperatures. Satisfactory plastic clays capable of withstanding these temperatures were not available, and the plant never operated successfully. PREPARATION OF BATCH Composition of the clay retort by weight was 40 to 50 pct raw clay and the balance "grog." Generally speaking the mix consisted of 7 parts plastic clay to 9 parts grog by volume. Principal source of the clay used was the Cheltenham vein—sometimes referred to as "St. Louis city clay." A typical analysis was A12O3-31.0 pct, SiO2-50.0 pct, Fe2O3-2.5 pct, MgO-0.3 pct, CaO-1.5 pct and loss on ignition 14.0 pct. At the smelter the clay was weathered whenever possible and then crushed to 0.08 in. or finer. Grog consisted of calcined adobies, cleaned retort scrap and cleaned refuse fire brick such as old furnace brick, blast furnace linings, and others. Saggers from ceramic plants and calcined flint clay were later used. The grog materials were ground to 0.12 m. or finer. Occasionally coke dust up to 10 pct of the mix was substituted for a part of the grog following European practice.² Particle size of the grog has a major influence on the retort properties—the larger the grain, the better can the retort withstand thermal shocks, resist bending at furnace temperatures and resist corrosion from slag; the smaller the grain, the lower the loss of zinc vapor through the retort walls. Grog forms the skeleton of the retort, and the clay shrinks around its grains to act as a binder. In the drying process, the grog has a stabilizing effect on the drying rate, decreasing shrinkage and giving up previously absorbed water to the surrounding clay to minimize the danger of cracking or checking.² Grog and clay were mixed through a horizontal pug mill with 10 to 20 pct water added, depending on whether the retort was to be formed by hand or mechanically, more water being required for the hand process. The batch or "mud" extruded from the pug mill was cut in convenient lengths for handling, stacked in piles or in special rooms, covered with wet burlap and allowed to "rot" or age from 1 to 8 weeks to increase plasticity. HAND MOLDING If the retort was to be molded by hand, the mud was repugged after the rotting period and given to the molders. Their molds consisted of 3 sheet iron or wood cylinders, each one third the retort length and defining the outer shape of the retort. Beginning with the bottom section, mud was placed in the form and tamped with a rammer

Jan 1, 1950

By D. J. McAdam, G. W. Geil, R. W. Mebs

AS shown in previous papers by the authors 9-l7† the resistance of a metal to fracture, like its resistance to plastic deformation, is a function of all three principal stresses.‡ A technical cohesion limit is the technically determined resistance to fracture under a specific stress system. The technical cohesive strength thus comprises an infinite number of technical cohesion limits corresponding to the infinite number of possible combinations of the principal stresses. The technical cohesive strength, therefore, may be represented by a surface in a diagram with the three principal stresses as coordinates. As shown in previous papers, 9-I8 the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress, § namely, the stress system, plastic deformation, temperature, and the strain rate. More- over, the influence of each of these factors on the technical cohesion limit has been shown to be qualitatively similar to the influence of the same factor on the flow stress.9-18 Advance of knowledge about the conditions determining fracture, of metals has been retarded by the reluctance of some investigators to abandon preconceived ideas about how metals "should" behave. The incorrect idea is still prevalent that the conditions determining resistance to fracture are very different from those determining the flow stress. Attempts are still being made to express resistance to fracture in terms of a single parameter, such as a limiting value of the greatest principal stress, the maximum shearing stress, or the volume stress (one-third the algebraic sum of the three principal stresses). In these attempts, a sharp distinction is sometimes made between a ductile or "plastic fracture " and a "brittle fracture." In making this distinction, however, the meaning attached to the term "brittle fracture" sometimes is not made clear. The term could mean fracture after very little plastic deformation or it could be used to designate the type of fracture. An ordinary fracture of a ductile metal at room temperature starts as a cleavage, generally transverse to the direction of the greatest principal stress, but eventually changes to a shearing fracture. In some conditions, however, the metal fractures entirely by cleavage, with no evidence of plastic deformation during the fracture; the surface of such a fracture may have a

Jan 1, 1947

By Thomas T., Read

T HE preceding chapter has recorded the initiation of mineral industry education during the period 1890-1910 in numerous institutions that had not previously offered it. It should also be emphasized that in many institutions where instruction had begun before 1890, as recorded in earlier chapters, but had not yet become firmly established,, this period was one of marked growth and development. This was not universally true, however, for at the Universities of Pennsylvania, Michigan, Illinois, Wisconsin, Washington (St. Louis), Iowa, Vanderbilt and Tennessee, and at the Polytechnic College of Pennsylvania, mineral industry instruction was being dropped during this period, instead of gaining in strength. It is necessary to emphasize this, because writers on the subject have not infrequently , attempted to make a much too simple correlation between mineral -discovery or production and the intensity of student interest in mineral industry curricula. It would naturally be true that periods of large mineral production would, in general, coincide with cycles of business prosperity, and the latter are conducive to starting new ventures, educational as well as business. It should be equally evident that opportunities for business and professional success might, in such periods, appear to increase at a more rapid rate in industries other than mineral, or in the utilization of minerals rather than in their production. The author has not been able to perceive any simple and clear relation between interest in mineral industry education and mineral discovery, production, and utilization, or general business prosperity. On the contrary, the more the problem is studied the more complex the factors involved in it appear to be. In a later chapter an attempt will be made to analyze them in more detail.

Jan 1, 1941

By Gerhard Bockstiegel

Kuczynski's formula has been derived for the case of nonspherical particles. TWO formulae of Kuczynski's type have been derived, one describing the increase in tensile strength, the other describing the progress of shrinkage of a powder compact. It has been strength,shown that the exponents of all three formulae each contain two magnitudes of different physical characters, viz, the geometrical factor a and the kinetic factor ß. The interrelationships between the three exponents are stated. SOME years ago Kuczynski1 experimentally showed that the radius, x, of the area of contact between very small spherical metal particles and a metallic block is related to the time of sintering, t, by the following equation x = constant tk [11 where k has the value 1/5 or 1/7. Assuming that the metal particles were perfect spheres and the metallic block was perfectly flat, he derived the foregoing equation from theoretical considerations of the process of material transport in metals, and he showed that exponent k is different for different mechanisms of transport, e.g., k = 1/2 for viscous flow (according to Frenkel2), k = 1/3 for evaporation and condensation, k = 1/5 for volume diffusion, and k = 1/7 for surface diffusion. From this Kuczynski concluded that the mechanism of transport was either volume diffusion or surface diffusion, depending on whether the value of k, as found in his experiments, was 1/5 or 1/7. Subsequently. Cabrera8 corrected Kuczynski's calculations with regard to surface diffusion, showing that the theoretical value of exponent k is 1/5 for both volume and surface diffusion. He supposed that the different experimental values of k were due to slight differences in the shape of the metal particles. An exponential relationship similar to the aforementioned was found by Okamura, Masuda, and Kikuta,4 Masuda and Kikuta, and Takasaki8 when studying the rate of shrinkage on powder compacts during sintering. The authors measured the shrinkage by means of the fraction w = Vp — V./Vp — V,,,, where V,, is the volume of the green compact, V, is the volume of the sintered compact, and V,,, is the volume of the compact in its densest state. This fraction, w, they found, is related to the time of sintering, t, by the equation w == constant tm. [21 Further, Bockstiegel, Masing, and Zapf7 observed that the tensile strength, s, of sintering iron powder compacts can also be related to the time of sintering, t, by an equation of the foregoing type, i.e., s = constant tn. [3] For exponent n the values 0.28 (S=2/7) and 0.35 ( 2/5) were obtained, and the authors pointed out that there might exist a simple interrelation between exponent n as found in their experiments and exponent k in Kuczynski's equation. The authors supposed that 2k = n, since the strength of adhesion between a metal sphere and a block (as in Kuczyn-ski's experiments) must approximately be proportional to their contact area, p. x2. Theoretical Considerations This paper is an attempt to correlate the fundamental experiments of Kuczynski's type with the results obtained with powder compacts as represented by Egs. 2 and 3. In particular, the paper is to show how the rate of sintering is influenced by the geometry of the sintering particles and by the type of material transport. As the geometry of particles conglomerating in a powder compact is very complex, some simplifying assumption has to be made, of course, in order to adapt the problem to mathematical treatment. In the following paragraph a suitable simplification is introduced, and Kuczynski's formula is derived for the case of nonsphcrical particles. Relation Between Area of Contact and Sintering Time—As the face of contact between two particles in a sintering powder compact is not necessarily a circle (as in the case of spheres sintering to a block), Kuczynski's formula is modified as follows: Let the perimeter of the face of contact be described by means of polar coordinates R, 4, as shown in Fig. la, so the area of contact, f, is determined by f= 1/2 . S112p[R(Æ) ]2 dÆ [4] Then, let the two particles be intersected by a plane perpendicular to area f. The intersection is shown in Fig. lb. According to the nomenclature in this figure, the distance, h, between the surfaces of the two particles is a function of T and Æ: h = h(r,Æ). For the particular case of spherical particles, as in Kuczynski's theory, this function becomes: h = constant r2. It shall be assumed here that in the close neighborhood of their

Jan 1, 1957

By George B. Langford

ON THE QUESTION of postwar controls there are today three schools of though ; some advocate state control of everything the socialists ; second are those who advocate the removal of all governmental control over industry - the freedom of enterprise ideal ; and third are those who advocate a middle course - sufficient control to stabilize economic and industrial life, and to prevent violent fluctuations such as we saw in the interwar years. I advocate this third course. I firmly believe un free enterprise, but not in freedom of enterprise, or laissez faire, and there is a great and significant difference between these two.

Jan 1, 1944

By Norman Lamont

The evaluation of certain reser-voir properties, such as porosity and fluid saturation, from electrical well surveys has been widely accepted in petroleum engineering. Various investigators have established relationships between these properties and certain parameters which affect the response of the electrical log. Among these are the resistivities of the mud, its filtrate, and its filter cake. In 1949, Patnode1 established a relationship between the resistivities of the mud and filtrate. The well logging service companies have contributed relationships for the mud-mud cake resistivities2,3 These have been valuable since it was the practice to measure only resistivity of mud at the well site. During the mid-1940's the industry began drilling wells with oil-emulsion drilling fluids. These were conventional aqueous muds with a dispersed oil phase. Since 1950, oil-emulsion muds have been used on an increasing number of wells each year. However, the practice of measuring only the resistivity of the mud at the well site has continued, and the mud filtrate and mud cake resistivities have been determined by the above-mentioned relationships. Service companies are now equipped to measure all three resistivities at the well site. An investigation was conducted on the resistivities of oil-emulsion muds, mud filtrates, and mud cakes to determine if these values conformed to the relationships for aqueous muds. TYPES OF MUDS Fifty-one oil-emulsion mud samples were prepared in the laboratory following a standard manual' published by a leading mud company. The diesel oil in the samples varied from 5 to 50 per cent, the majority of the samples being in the 10 per cent region. The basic aqueous mud types which were converted to oil-emulsion muds were commercial clay and bentonite muds, low pH and high pH, caustic-quebracho treated muds, and lime treated muds. The emulsions were stabilized by dispersed solids, lignins, lignosulfo-nates, sodium carboxymethyl cellulose, or sulfonated petrolatum. It is worthy of note that after a quiescent period of two weeks at room temperature all samples, regardless of emulsifying agent, remained stable. The make-up water for the muds was from the laboratory tap. Resistivities were varied by the addition of table salt to the water. A range of mud resistivities from 0.44 to 3.9 ohm-m was obtained in this way. Twenty-three field muds were tested. These covered the same range of mud types as did laboratory muds. Oil provinces of the Gulf Coast, South Texas, West Texas, Oklahoma, Montana, and Canada were represented. MUD TEST PROCEDURE Each mud was tested for density, viscosity, pH, and filter loss by standard testing techniques. The resistivity measurements were obtained with a Schlumberger EMT meter. This meter required small volumes of sample, e.g., 2 mm. Filtrate was obtained from a Standard Baroid fil-ter press at the end of a 30-minute test. The filter cake from the same test was used for cake resistivity measurements. Mud, filtrate, and cake samples were heated to 100" F in a constant temperature water bath prior to measurement of resistivities. RESULTS The relation between mud resistivity (Rm) and mud filtrate resistivity (Rmf) is shown in Fig. 1. The solid line represents an average for the data. The equation of this line is Rmf =0.876 (Rm) 1.075 . . (1) Arbitrary limits, indicated by the dashed curves, have been set. The majority of the data falls within these limits, but some points do lie outside the limits. The approximate equation Rmt = 0.88 Rm , . . . . (2) will give satisfactory results within these limits. The data on mud cake resistivity Rmc is shown in Fig. 2. The solid line is an average for the data. The equation for the line is Rmc = 1.306 (Rm)0.88 The dashed lines are arbitrary limits on the data. Within these limits, Eq. 3 may be simplified to Rmc = 1.31 Rm . . . . (4) DISCUSSION The limiting curves in Figs. 1 and 2 represent maximum deviations of ±25 per cent. Thus the use of the average curves can introduce considerable error. There is no substitute for accurate measurements of mud, mud cake, and mud filtrate resistivities at the well site. The mud sample tested should be representative of the mud opposite the formation being logged. The average mud filtrate resistivity curve of Fig. 1 is reproduced in Fig. 3 with two curves which have been published for clay-base aqueous muds2,3. The latter curves were determined from average values of a large number of drilling fluids. The three curves have essentially the same slope and the differences between them are from 7 to 22 per cent. Comparison is made only to illustrate the possibility of error

Jan 1, 1958

By Michael J. Messel

OF the various minerals that occur in fibrous form known as asbestos, chrysotile is the variety most in demand for commercial uses, and, last year, over 683,000 tons of the various grades were produced in Canada and United States, exclusive of African and Russian production, which figures are uncertain. Production has not been able to keep up with the increased demand, and an acute shortage exists. Canada, Russia, and Africa are still the most important producers. However, Russia consumes most of its production at home and exports very little. The United States consumes over 60 pct of the total production and produces only about 4 pct of the total from deposits in Vermont and small quantities from Arizona. This paper will review mainly, some of the more recent developments concerned with the extraction and processing of this fibrous mineral for various industrial uses, such as textiles, insulation, building materials and brake linings.

Jan 1, 1949

By Albert Ladd Colby

PAGE I. Introduction,...........577 11. PRocess of Manufacture. 1. American Specifications. 2. Foreign Specifications, . ......... 580 III. Chemical Properties. I. Chemical Composition: (a) American Specifications ; (b) Foreign Specifications. 2. Chemical Analysis: (a) American Specifications ; (b) Foreign Specifications ; (c) Number of Analyses Required ; (d) Sample for Analysis ; (e) Check-Analyses Impracticable ; (f) Rejection Solely on Variation in Com-' position,............581 IV. Physical Properties. 1. Drop-Test and Drop-Testing Hachine: (a) American Specifications ; (b) Foreign Specifications ; (c) Limits in Deflection. 2. Tensile Test: (a) American Specifications; (b) Foreign Specifications ; (c) Test-Pieces are not Representative ; (d) Specified Tensile Strength is Affected by the Section ; (e) BpeciBed Tensile Strength is Often Inconsistent with Specified Chemistry ; (f) Specified Tensile Strength is Often Inconsistent with Specified Elongation ; (g) Amount of Tensile Testing Required is Excessive ; (11) Conclusions. 3. Dead-Weight Test: (a) American Specifications; (b) Foreign Specifications; (c) Number of Tests Specified. 4. Bending-Test: ((1) American Specifications ; (b) Foreign Specifications,..........589 V. Section. 1. American Specifications. 2. Foreign Specifications: (a) Templets ; (b) Sample Piece of Rail; (c) Allowable Variation from Templet,...........601 VI. Weight. 1. American Specifications. 2. Foreign Specifications,. . 603 VII. Length. 1. American Specifications. 2. Foreign Specifications, . . 604 VIII. Drilling. 1. American Specifications. 2. Foreign Specifications, . 604 IX. Finish. 1. American Specifications. 2. Foreign Specifications, . . 50.5 X. Branding. 1. American Specifications. 2. Foreign Specifications : (a) Data to be Rolled in Raised Letters on Web of Rail ; (b) Marking of the Blow-Number on Each Rail; (c) Additional Marking and Painting of Rails,........605 XI. Inspection. 1. American Specifications. 2. Foreign Specifications: (a) Prior Notice of Rolling; (b) Free Access to the Works ; (c) Cost of Inspection, Analyses and Tests to be Borne by the Manufacturer ; (d) Rails after Inspection by Manufacturer to be Sorted into Lots Prior to Inspection by the Engineer ; (e) Disposition of Rejected

Jan 1, 1907

By R. Maddin

IN analyzing the relation between the orientation of new grains and that of the deformed matrix of axially extended and recrystallized single crystals of face-centered cubic metals, a two-stage rotation process" is generally used where the first rotation is made in order to account for an "adjustment of orientation to the environment of strain."&apos; It has been argued that in spite of the difference of orientation, which may amount to as much as 12" (in a brass),&apos; between the octahedral plane as observed in the parent lattice and in the recrystallized grain, it is believed to be a common plane in the sense that it constituted the nucleus in the parent strained crystal from which the new grain grew.&apos; A possible source of the deviation in orientations of a common pole in the new grain and that of the deformed single crystal matrix from which it has grown may be found in the distribution of strain resulting from the plastic deformation. It might be expected in view of the incongruent nature of shear&apos; that the perfection of the octahedral plane along which glide has occurred is disrupted and that this disruption constitutes the strain from which nuclei of new grains can grow during recrystallization. Evidence for the existence of strain along glide planes was first detected by Taylor" in 1927 and substantiated by Collins and Mathewson&apos; in 1940. In their investigations, however, the deformed single crystalline specimens (aluminum) were cut mechanically along the glide planes followed by mechanical polishing. X-ray exposures (glancing angle) of only 8 min with filtered radiation were used. It was later shown&apos; that this type of surface preparation did not remove with all certainty the mechanically disturbed surface. It was felt that a re-investigation of this phenomenon using more refined techniques might reveal a more correct extent of the strain resulting from the deformation which might correlate the deviation of the common pole of the recrystallized grain with the acting slip plane of the matrix crystal. In accordance with these thoughts, a single crystal of a brass (70/30 nominal composition) M in. in diam x 5 in. long, tapered as in previous experiments,&apos; was extended and carefully documented with respect to elongation and shear. Disks about % in. thick paralle&apos;l to the primary slip planes were cut from the specimen by means of an etch cutter." These disks represented volumes of the specimen which had been extended 0, 5, 10, 15, and 20 pct. Copper Ka monochromatic radiation was obtained by reflecting 35,000 v copper radiation from the c-cleavage face of a pentaerythritol crystal. The monochromatic radiation was collimated and led on to the disk set at the proper 0 angle for reflection from the primary (111) planes. The monochromatic beam was aligned in a plane containing the active slip direction. Following a 10 hr exposure at the theoretical Bragg angle, the disk was reset at 0 + 1°, 0 — 1", 0 + 2", 0 — 2", etc., until no Bragg reflection was obtained. The disk was then rotated 90" about its polar axis, and the same X-ray procedure was used. The results are shown in Table I. It may be seen from the results in Table I that the plastic deformation (20 pct elongation) produces fragments of the glide plane which are rotated or tilted as much as 25 " from the normal position on a purely block slip model. In addition to the large variation in 0 angle in the slip direction, there is a variation in 0 as much as 20" in the direction at right angles to the direction of slip, i.e., <110>. In view of the results shown, it may now be argued that the strain distribution finds its origin in the incongruent nature of the slip process.&apos; The use of the two-stage rotation process seems valid in attempting to explain the relation between the orientation of recrystallized grains and the matrix from which they have grown. Acknowledgment This work was sponsored by the ONR under Contract Number N6 onr 234-21 ONR 031-383. The author would like to thank N. K. Chen for reading and correcting the manuscript. References &apos;R. Maddin, C. H. Mathewson, and W. R. Hibbard, Jr.: The Origin of Annealing Twins. Trans. AIME (1949) 185, p. 655; Journal of Metals (September 1949). &apos;J. A. Collins and C. H. Mathewson: Plastic Deformation and Recrystallization of Aluminum Single Crystals. Trans. AIME (1940) 137, p. 150. eN. K. Chen and C. H. Mathewson: Recrystallization of Aluminum Single Crystals After Plastic Extension. Unpublished. 4 C. H. Mathewson: Structural Premises of Strain Hardening and Recrystallization. Trans. A.S.M. (1944) 38. :&apos;C. H. Mathewson: Critical Shear Stress and Incongruent Shear in Plastic Deformation. Trans. Conn. Acad. of Arts and Science, (1951) 38, p. 213. "G. I. Taylor: Resistance to Shear in Metal Crystals, Cohesion and Related Problems. Faraday Soc. (1927) 121. &apos;R. Maddin and W. R. Hibbard, Jr.: Some Observations in the Structure of Alpha Brass After Cutting and Polishing. Trans. AIME (1949) 185, p. 700; Journal of Metals (October 1949). &apos;R. Maddin and W. R. Asher: Apparatus for Cutting Metals Strain-Free. Review of Scientific Instruments (1950) 21, p. 881.

Jan 1, 1953