Search Documents

By J. H. Mallery, J. H. Keeler

THE crystal structure of Zral, the compound richest in zirconium (91.03 pct Zr by weight) in the system Zr-Al, has been found to be ordered face-centered-cubic. This compound is of particular interest, since it is encountered as the precipitated phase in potentially useful zirconium-rich alloys. It forms peritectoidally from body-centered-cubic zirconium and Zr,Al at about 975°C. The Zr-A1 constitution diagram has been reported by McPherson and Hansen.' For the primary determination a 100 g ingot was prepared by arc-melting in a water-cooled copper crucible under purified argon. The raw materials were crystal-bar zirconium (a purity of better than 99.7 pct) and spectroscopically pure aluminum. The ingot was double melted, examined metallographi-cally, and found to be quite uniform as shown in Fig. 1. The hardness of the as-cast button was VHN 390 to 445. A 20 mil diam specimen was prepared from annealed (900°C) filings of Zr,Al. The specimen was mounted in a 5 cm radius powder camera and an 8 hr exposure was taken using copper radiation with a nickel filter. The structure of the compound Zral was found to be ordered face-centered-cubic of the Cuau type, with an a,, value of 4.37220.003A. Its calculated density is 5.976e0.013 g per cu cm. The relative intensities for the lines were calculated using the formula 1+cos2 20 I oc----------------- • p • /F7 sin2 0 cos 0 1 + COS' 20 where----------------is the Lorentz polarization fac- sin2 0 cos 0 tor, p is the multiplicity factor, and F is the structure factor. The X-ray data are given in Table I. The compound has exhibited plasticity when present as particles in a matrix of a zirconium. During hot working at about 900°C, the compound has been found to deform plastically to the extent that some of the particles exhibit a length-to-width ratio greater than 4:1 as shown in Fig. 2. In answer to the discussion of ref. 1, McPherson and Hansen pointed out that the compound may be cold rolled and reduced as much as 33 pct. Zr,Al has also been found2 under certain conditions to precipitate in lamellar form at grain boundaries of the a phase of hexagonal-close-packed zirconium. Acknowledgment This work was carried out under Contract W-31-109-Eng 52 for the United States Atomic Energy Commission.

Jan 1, 1956

By W. C. Hagel, J. H. Westbrook

Usittg a sectioning technique with Agl10 as the tracer, the diffusion of silver in silver-excess (45.8 at. pct Mg), near-stoichiometric (49.8 at. pct Mg), and magnesium-excess (52.0 at. pct Mg) cylinders of CsCl-type AgMg was determined from 500" to 700°C. Diffusion coefficients conform to the expression D = Do exp (-q/RT) where the respective Do values are 1.53, 0.280, and 0.134 sq cm sec-I and the Q values are 41.3, 40.6, and 38.0 kcal g-atom-'. Lnttice-parameter and density measurements were performed on a more numerous assortment and wider range of compositions. Substitutional defects were found on both sides of stoichiometry. Activation energies for other rate processes in these alloys show related trends with changing composition, although silver may not be the rate-detemining species. KNOWLEDGE of diffusion coefficients is necessary for a quantitative understanding of the many rate processes (e.g., grain growth, precipitation, sintering, oxidation, or mechanical deformation) occurring in solids. Although these data are available for most metals and common alloys, they are quite limited for intermetallic compounds—a group of materials whose unique physical and mechanical properties are presently attracting great interest. From a fundamental viewpoint, diffusion in intermetallic compounds also offers several engaging aspects owing to: their ordering, the possibility of introducing large, stable concentrations of lattice defects, and the variety of bonding types and crystal structures which can be found. In the case of CsC1-type compounds, some previous work has been directed at examining the role of vacancy defects by changing their concentration compositionally. The diffusion of Co60 was measured in 0 NiAl1- and in P COA., Except for the results of Smoluchowski and Burgess, isothermal diffusion coefficients were found to pass through a minimum at the stoichiometric composi- they decreased sharply on what was reported by Bradley and co-wrkers' to be the vacancy-rich (aluminum excess) side of stoichiometry. This investigation of the diffusion of Agl110 in AgMg was undertaken both as an adjunct to a concurrent study of its deformation behavior and for the purpose of obtaining information on the influence of lattice defects and temperature on diffusion in another CsC1-type intermetallic compound. Bcc AgMg remains ordered up to and melts congruently at 820°C. Solubility limits at 300°C are about 41 at. pct Mg and 53 at. pct Mg. It is one of the Hume-Rothery electron compounds with a 3/2 electron-atom ratio. Previous investigations of its properties include hardress,' tenile,'-' electrical reistivity, and thermodyna-mic1',14 studies. Indications of a high bonding strength may be found in the large heat of mixing1' and in the 6-pct vol contraction on compound formaticp, as calculated using atomic radii of l.40 and l.55a for Ag and Mg. EXPERIMENTAL PROCEDURE Alloys were prepared by the induction melting of selected fine silver (99.95) and low-iron magnesium (99.95) in magnesia crucibles under 1 atm of A. Supplied by the Handy and Harmon and Dow Chemical Cos., respectivelv. Melts were poured under argon into graphite molds providing 1 1/8-in.-diarn. by 4-in.-long ingots. These were homogenized in evacuated and argon-filled fused-silica capsules by heating for 16 hr at 750'. Three 1 in.-diam. by 3/4-in.-long cylinders were machined from the mid-portion of each ingot for diffusion measurements. Three alloys, analyzing 45.8, 49.8, and 52.0 at. pct Mg were taken as representing the extremes of interest, with 49.8 at. pct Mg being very close to the stoichiometric composition of 50.0 at. pct Mg.

Jan 1, 1962

Edward Keller, Baltimore, Md. (communication to the Secretary): When, at the New Pork meeting, February, 1899, Mr. Douglas gave an abstract of his highly interesting paper on the Copper Queen mine, he invited the members of the Institute, in his usual progressive spirit, to make a full scientific investigation of the region of that mine during the prospective excursion to Bisbee, Arizona. I volunteered to examine some of the metallurgical processes and products of the works, and obtained from Mr. Douglas a valuable series of samples. Upon the issue of his paper, however, I found that he had already a considerable volume of analyses of those products, and that little was left for me to do in that respect, except to duplicate his results, the importance of which work would not have been commensurate to the time and labor involved. I selected, therefore, only some points which he had not made entirely clear, or concerning which I was skeptical. The details of most of my work will appear in a future paper. From Mr. Douglas's figures I have calculated the values for the elimination of impurities in the so-called Leghorn converter, introduced by him at the Copper Queen works, and have found them to be as follows: Percentage of Elimination of Impurities in Pour Blows of a Converter. No of ' Selenium Sulph'r Iron. Zinc. I Nickel. Lead. Antimony Arsenic. and Blow- ! Tellurium .. 1.......... 99.4 99.6 88.0 92.6 94.4 81.6 83.8 40.3 2.......... 99.0 99.6 98.1 92.5 96.8 71.9 76.6 38.1 3.......... 98.8 99.5 93.5 91.4 96.3 63.8 80.6 25.3 4.......... 99.8 99.5 95.8 95.8 97.5 65.3 76.9 36.3 Average 99.2 99.6 93.8 93.1 . 96.2 70.6 ! 79.5 35.0

Jan 1, 1900

THOSE NOT MARKED ARE MEMBERS; MARKED THUS ? ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. JUNIOR ASSOCIATES ARE MARKED II. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. ?AARONSON, ALFRED E Pres., Tuloma Oil Co., Unity Bldg., Tulsa, Okla. '18 ABADIE, EMILE R., Min. Engr Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Gen'l Supt., Iron Mines Div., Tenn. Coal, Iron & R. R. Co. 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, LOUIS BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div. Jenkins, Ky. 115 ABBOTT, ROBERT R. Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Fujitagumi Taiwan Office, Taipeh Formosa, Japan. '14 ABEEL, GEORGE H., JR., Cons. Min. Engr., 4111 Lafayette Ave., St. Louis, Mo. '18 ABEY, HIROSHI, Min. & Met. Engr., Arakawa Mine, Mitsubishi Co., Senpoku-gun, Akitaken, Japan. '17 ||ABOUCHAR, S. S., Cia. de Minerales y Metales, S. A. Santa Eulalia Unit, Apt. 70, Chihuahua, Chih., Mexico. '17 ABRAHAMS, A. I 1391 Madison Ave., New York N. Y. '14 ?ACKER, E. O'C., Met., 128 East Washington Lane, Germatown Philadelphia, Pa. '86 ACKER, WILLIAM L., Diamond Drill Contractor... Mears Bldg., Scranton, Pa. '18 ?ACKERMAN, ERNEST R., Pres., Lawrence Portland Cement Co. Plainfield, anion Co.. N. J. '15

Jan 1, 1923

ALABAMA. Anniston.-Noble, A. E., 20th St. and Wilmer Ave. Auburn.-Brown, R. L., Box 0. Belle Ellen.-Hutcheson, W. C. Bessemer.-Abbott, C. E., T. C., I. & R.R. Co Dobbs, G. G., Box 97. Ferguson, V., U. S. C. I. Pipe & Fdy. Co. Williams, E. P., Tenn. C., 1. & R. R. Co. Birmingham.-Aldrich, T. H. Aldrich, T. H., Jr., 406 Woodward Bldg. Allen, A. W., 1616 S. 14th Ave. Bowron, J., 1401 S, 20th St. Burbidge, T. A., Brown-Marx Bldg. Coxe, E. H. Tenn. C., I. & R. R. Co. Crawford, C. G., Tenn. C., I. & R. R. Co. Crockard, F. H., Brown-Marx Bldg. Ellis, E. E.,1515 Brown-Marx Bldg. Fairbairn C. T., Woodward Bldg. Fies, M. H., 2316 Highland Ave. Geismer, H. S., Keiser-Geismer Engrg. Co.

Jan 1, 1917

By Gordon B. Brox, Joseph F. Mcaleer, Charles C. Goddard, Edward P. Shea, Robert G. Ingersoll, Lester G. Zeihen, George J. Burns, John M. Guilbert, Richard N. Miller, Charles Meyer

The Boulder batholith is a composite intrusive in which the Butte quartz monzonite is the dominant rock type. Quartz porphyry dikes intruded the quartz monzonite in directions which were subsequently followed by the eastwest- striking Anaconda system of veins, the earliest major veins in the district. Anaconda veins are faulted by northwest-striking veins of the Blue system, which are most prominent in the central third of the district. Anaconda veins are the major producers in the western third of the district and also in the eastern third, where the "horsetail" zones break off from them. Individual oreshoots are thousands of feet long as well as deep on both systems of veins, but they are generally more persistent and thicker on the Anaconda veins. Viewed broadly, the mineralization in the big veins is arranged in crudely concentric zones of zinc and manganese around a central zone of copper. Only slightly offset from these zones, but earlier structurally, is a zone in which quartz-molybdenite veinlets are prominent. This zone tops at about the 2800 level and widens downward. The pattern of distribution of Cu-Fe-S series minerals in the large veins of the copper zone is not symmetrical with respect to the metal zones. There is a fringe of chalcopyrite-bornite all around the copper front. However, within the copper zone, pyrite-chalcocite-enargitecovellite- digenite assemblages are prevalent near its eastern edge from the 3800 level to the surface, whereas deep on the large Anaconda veins in the western part of the copper zone, chalcopyrite is dominant. Here the chalcopyrite grades upward into bornite-chalcocite ores and eastward into the high-sulfur assemblages of the Leonard mine. Sericite-biotite-K-feldspar alteration envelopes, containing up to about 2 per cent copper as chalcopyrite, are present on some of the quartz-molybdenite veinlets at deep mine levels in the molybdenite zone. These envelopes contrast sharply mineralogically and chemically with the later sericitic and argillic alteration envelopes around Main Stage veins. K'0-Ar'0 ratios indicate that they may be older by about 4 m.y. Secondarily enriched copper ores are mined in the Berkeley pit in the southeastern part of the district. At the present time they account for about half of Butte's production of copper.

Jan 1, 1968

By J. A. Richardson

J. A. RICHARDSON[t]-Mr. Stuckey's account of the geology of the kaolins of North Carolina suggests that they exhibit some features similar to those of the Malay Peninsula. About one half of British Malaya (some 26,000 square miles) is occupied at the surface by igneous rocks, of which granite and its associated derivatives constitute fully 90 pct. The average granite is a biotic variety. It is predominantly potassic but carries, in addition, notable amounts of soda and lime so that albite and albiteoligoclase are generally common constituents of the rock. The minor derivatives from granite "magma" likewise include potassic and sodi-potassic members. Decomposition of the granitic rocks has led to the formation of kaolin in many localities, but, in general, the deposits are rather small and, at present, none is exploited commercially. True primary or residual kaolins (as defined by Stuckey; p. 48 Vol. 173, p. 2 TP 2219) have been developed from feldspar veins, pegmatites and from other granitic differentiates which cut through the larger masses of granite; they are usually small and narrow. Kaolin has been derived from aplite, quartz porphyry, quartz micro-porphyry, felsites and microgranites belonging to a complex known as the Chegar Perah-Pulai intrusion in northwest Pahang and southwest Kelantan. The bulk of the component rocks has been more or less strongly sheared. Kaolin-like end products have been formed from both sheared and nonsheared varieties. Kaolin has been formed also by the complete breakdown of trondjemite flanking the northwestern and western margins of the complex Bukit Ranjut syenite intrusion in northwest Pahang. These trondjemites range in composition from essentially quartz-free albiteplagioclasites to quartz-free microcline rocks; they are, in effect, the syenitic homologues of white sodic and potassic granite-aplites. The granites in Malaya have generally undergone more or less severe surficial weathering leading to the production of a spongy and rather cellular or a soft "mealy" material (sandy clay) down to depths of about 100 ft; in places the granite is strongly decomposed down to 150 ft. There has occurred, therefore, widespread partial kaolinization, but, in general, no extensive deposits of good quality kaolin seem to have been formed by these processes of decay. Frequently, the katamorphic processes of desilicification have advanced beyond the production of kaolin towards the formation of lateritic end products. The more important Malayan kaoiins seem to be confined to the western alluvial plains, particularly in areas either where granite crops out at surface, or where it forms the bedrock of the alluvium. There are numerous excellent examples around Gopeng and elsewhere in the Kinta Valley of Perak. Such kaolins belong to Stuckey's groups of secondary deposits, and, like them, these also may be bedded. Field observations have established the existence of what for want of a better name is referred to by the Malayan Geological Survey as "granite wash." It is believed that granite, undergoing extensive deeply penetrative and probably rather rapid destruction under humid tropical weathering (temperature around 90°F; rainfall about 100 in. per annum; high humidity) "flowed," was moved by "creep" and, in addition, probably slumped in large waterlogged masses of sandy clay from topographic salients onto the adjacent flats. Either during this period of transmigration or later when the sludged granite detritus, after having more or less come to rest, was attacked by flowing water, differential sorting and erosion took place with the result that the resorted debris was moved and later deposited as bedded alluvium. In this way, banded "granite wash" was produced comprising alternating bands of clayey sand (resorted granite sludge) and white

Jan 1, 1947

By Thomas V. Falkie

Mining and exploration, in the year 1971, can be characterized as a year of politics and the beginning of an era of legislation. Certainly the activities of our state and federal lawmakers and international politicians over-shadowed technical developments, which are outlined in the following pages. The nationalization of the Chilean copper industry was the most far-reaching event of the year. Not only will it have an effect on international metal trade, but the nationalization will also affect the major mining companies in such a way as to cause strategic, managerial and technical adjustments in metal mining and exploration efforts in other parts of the world.

Jan 2, 1972

By Charles W. Bloomquist

The profitability of miscible flooding in a hypothetical target oilfield is examined. The major costs, including Windfall Prof it Tax, are identified and their re1ative importance are discussed. The sensitivity of profit to important physical and economic variables is evaluated and discussed, including variance in oil recovery, oil price, injectant requirements, injectant cost, and capital requirements. Economic sensitivities to important development and operating decisions such as timing, Spacing, Slug size, and gas recycling are also analyzed. The Windfall Profit Tax (WPT) as it applies to gas miscible EOR projects is reviewed. The effect of WPT on each of the various project cases is analyzed and the effect of reduced WPT on remaining production from existing operations is evaluated. Tax implications are compared for integrated vs. "independent" controlled projects and the alternative of expensing vs. capitalizing tertiary injectants is also evaluated. The impact of the Net Income Limitation in reducing WPT. during early and late project life is determined and discussed.

Jan 1, 1982

Jan 1, 1948

Jan 1, 1948

By D. J. DeLazaro, W. Rostoker, R. E. Riley, M. Hansen

KNOWLEDGE of the isothermal transformation behavior and the TTT chart method of graphically summarizing such information has been of invaluable aid to the ferrous metallurgist in understanding and developing heat treatments intended to provide specific mechanical properties. It is to be expected that similar lines of study directed to titanium-base alloys will be as profitable. This paper summarizes, on conventional TTT charts, the isothermal transformation products and pertinent reaction rate data for binary alloys of titanium containing 1, 3, 5, 7, 9, and 11 pct Mo, respectively. The results so presented were derived from metal-lographic examination. Some X-ray diffraction work was done to clarify certain points of question. Ti-Mo System To the authors' k.nowledge, TTT charts have only been used to describe the reaction rates of eutectoidal decompositions. It would seem that the kinetics of decomposition of any unstable solid solution might be conveniently described in this manner. The equilibrium diagram of the Ti-Mo system' is shown in Fig. 1. The similarity with the Fe-Ni system will be recognized. Additions of molybdenum serve to stabilize the /3 phase to increasingly lower temperatures. The solubility of molybdenum in the a phase is restricted to less than 1 pct at 600°C. Under normal conditions. a homogeneous ,8 structure quenched to a, temperature in the a f & field will reject a of invariant composition. The rate at which this occurs depends on the degree of undercooling and the degree of supersaturation of /3. The structural character of the rejected phase may also be expected to be related to the undercooling. Materials and Experimental Methods A sponge titanium was used which has a nominal impurity content as reported in Table I. The nominal composition of the molybdenum used is also included. The alloys were prepared in 150 g melts by arc melting in an evacuated water-cooled copper crucible of the type reported in an earlier paper.' The pancake-type ingots were forged to 1/4x1/4 in. bars and homogenized for 24 hr at 1000°C in evacuated Vycor bulbs. Specimens Vi in. thick were cut from these bars for heat treatment. The heat treatment cycles followed an invariant procedure. The specimens were soaked at 1000°C for 20 min under a helium protective atmosphere prior to quenching into a lead bath held at a temperature corresponding to a chosen degree of undercooling. After a prescribed period of time at this temperature, the specimen was removed and water quenched. A series of specimens so treated for progressively longer periods served to establish the times for initiation and completion of the decomposition of the /3 phase at a particular temperature. Although heat treatment of unprotected specimens in a lead bath does permit surface contamination by lead diffusion, this method is necessary to insure sufficiently rapid quenching rates. As long as the bath treatments were of less than 1 hr duration. the contaminated surface was not unduly deep and could be removed without excessive grinding. Metal-lographically, the contaminated zone could be readily distinguished from the pure binary alloy. Transformation Characteristics of Ti-Mo Alloys Metallographic examination showed that a supersaturated p phase may decompose by one of two processes. Alloys containing 1 to 9 pct Mo, when quenched in water from the homogeneous /3 field,

Jan 1, 1953

Members whose deaths were reported from Apr 7, 1923, to Apr 5, 1924 Elected Died 1918 ADKINSON, HENRY M 1923 1900 AGNEW, WILLIAM C 1923 1894 ASHLEY, H H 1923 1897 AUSTIN, KENNETH 1924 1903 AYERS, EMMA L C 1923 1913 BAECHTOLD, CHARLES A 1924 1900 BAIN, HUGH A 1924 1919 BASHORE, E GORGAS 1923 1920 BATTELLE, GORDON 1923 1923 BAYLES, GERARD L 1924 1881 BROCK, CHARLES 1923 1903 BROOKE, HENRY 1923 1876 BROWN, HARVEY H 1923 1904 BROWN, THOMAS E 1923 1919 BUCK, DANIEL M 1924 1906 CHALMERS, THOMAS S 1924 1881 CLEMES, JOHN H 1923 1896 COLLINS, HENRY F 1924 1871 COURTIS, WILLIAM M 1923 1915 CRESSON, B F, JR 1923 1921 CROWE, WALDO P 1923 1920 DARNELL, J ORA 1923 1911 DAVIS, HENRY G 1924 1918 DAVIS, ROBERT S 1923 1916 DEANE, WILLARD A 1924 1901 DEMPSTER, WILLIAM 1924 1911 DEVEREUX, W B, JR 1923 1895 DICKENSON, F M 1924 1904 DRUM, FRANK G 1924 1875 DUDLEY, P H 1924 1916 EATON, ARTHUR 1923 1919 EATON,SHERMAN 1924 1911 GRIFFITH, WILLIAM 1924 1919 HILSDALE, PAUL 1923 1922 HODGES, I F 1923 1916 HOFIUS, MAX, T 1924 1914 HUGHES, HOWARD R 1924 1919 HUMMEL, CARL B 1923 1874 HUNT, ROBERT W 1923 1921 JONES, ERNEST EVANS 1923 1917 JOSLIN, CHARLES T 1923 1918 KASJENS, JACOB G 1923 1899 KIRKEGAARD, PETER 1924 1920 KLAUS, HARRY C 1923 1892 KNOERTZER, HENRI1924

Jan 1, 1923

By C. R. Kuzell

IN COMPARISON with recent years 1932 has yielded much less tangible evidence of progress in copper reduction and refining. The industry has been extremely quiet, especially in the United States. Design and construction has been throttled by lack of new capital expenditures. The excess producing capacity of the whole industry and the extremely gloomy outlook for the future have made it unwise to tie up more capital except under special conditions. The plants built during the previous year have, however, been placed in operation. Older plants have been abandoned, temporarily shut down, placed on part time operating basis, or continue to operate at a low percentage of normal capacity. In the United States the Phelps Dodge Corporation at Douglas, Ariz., has completed the remodeling of the former Calumet & Arizona smelter. A new roaster and Cottrell plant chimney was completed this year. Though operations have been limited the new equipment has been found to justify all expectations. The reverberatory plant addition consists of two furnaces 26 by 107 ft. inside dimensions, with a high arch, and modern steel binding of excellent design. Natural gas fuel gives good results. One of these furnaces will treat 1000 tons of solid charge per day with a fuel consumption of approximately 3,000,000 B.t.u. per ton. The larger converters have not only yielded the expected lower costs, but have simplified operations in the converter department. One of the noticeable results is the greater cleanliness in the environment and the absence

Jan 1, 1933

By Henry M. Otte, Ralph P. I. Adler

The changes of line position and integral line breadth in the X-ray diffraction pattern of a polycvys-talline Cu-30Zn tensile test piece, incrementally loaded (and unloaded) up to fracture, have been an-alyzed in detail. The stacking-fault probahility, cv, increased linearly with increasing strain, E, wheveas the effective domain size, De(hkl), decreased with decreasing E-1 Over the greater part of the stress-strain curve the rate of work hardening was essentially constant (about 86 kg per sq mwz), and could be correlated with the slope of stage II of the single-crystal stress-strain curve. Consequently the theories of work hal-dening (particularly those parts relating to stage 11) as developed by Mott and Hivsch and others could be applied to the observations made on the polycrystalline brass. A relationship of the form Aa = Aao - MhklEhkl between the change, Aa, in the extrapolated lattice pararneter and the rvns strain, Ehkl, was derived and found to fit the results acceptably well. From this and other relationships developed in the papev it was estimated that the equilibrium stacking-fault energy of Cu-30Zn was between 8.4 and 12.5 ergs per sq cm, in fuirly close agreement with the (corvected) value obtained by Howie and Swann (1961)43 using transmission electron microscopy. The theory of work hardening in the jorm developed and recently presented by Hirsch (1964)3 successfully described all the pvesent observations. In order to test certain aspects of the theories of work hardening, as developed by Mott,1 Hirsch,2,3 Seeger et el,4-7 and others (for review see Nabarro, Basinski, and Holt8), several recent investigations have been concerned with relating the dislocation density, p, with the shear stress, 7 (and strain, y), applied to the specimen. The results of these investigations have shown that the square root of the dislocation density appears to be linearly related to the applied shear (or flow) stress for fcc as well as bcc metals and alloys. Furthermore, the relationship appeared to apply not only to the deformation of poly-crystalline specimens, but also to stages I and I1 of the deformation of single crystals. An expression of the form has thus come into wide use. Here b is the Burgers vector for a total dislocation, G is the shear modulus, and 70 and q are constants. A review9 of available values of q shows it to have values (at room temperature) in general between 0.3 and 0.6. Forms of Eq. [1] can be deduced from, or predicted by, the current theories, and the various constants adjusted so that they are compatible with the experimentally found value of q . No unique relationship has yet been found between the dislocation density and the applied shear strain. There are several serious objections to the use of Eq. 11]. In the first place, it relates the shear stress to the density of the dislocations without regard to their arrangement, type, or distribution; the significance of the relation may therefore be justly questioned.5 In the second place, the values of the experimental quantities usually substituted into Eq. [11 are those of the applied shear stress and the total dislocation density measured after unloaditzg. The dislocation density value that should in fact be used is that for the mobile dislocations present in the specimen when under the applied load.* Finally, in cases where the values used for p, the dislocation density, are those obtained by electron microscopy, p is subject to considerable error,' both systematic and random. The corrections to be applied are still controversial. Dislocation densities can also be measured by etch-pit and other techniques,'' each having their specific limitations. An objective of the present investigation has been to obtain information about the dislocation configyration and distribution by analyzing the changes in the position and shape of X-ray diffraction profiles as a function of deformation. The X-ray techniques employed, also open to criticism, have certain advantages, however. Thus, although the X-rays diffract only from the surface layers to an effective depth of about 20 p, the measurements can be made while the specimen is under load. The value of the dislocation density obtained by the X-ray method is also subject to errors, which are different from those of the electron microscope. Though a considerably larger volume of material is sampled by the X-rays, thereby reducing some of the statistical errors inherent in the electron microscope data, the information obtained is less detailed and is dependent on the method of analysis used to obtain a value for the dislocation density. Nevertheless, important observations can be made because the aforementioned advantages outweigh some of the limitations. In the present paper the X-ray method is briefly described and applied to a brass specimens deformed in tension. The results are then discussed in terms of some of the current concepts of work hardening. 1) EXPERIMENTAL PROCEDURE Details have already been extensively published elsewhere11-14 and therefore will only be dealt with briefly here. 1.1) Materials and Specimen Preparation. Commer-

Jan 1, 1968

By Paul M. Tyler

NOW that the dust of World War II has settled and we and our allies are faced with extravagant losses of men, money, and materials, virtually the only hope that the United States and Britain have in the way of reparations lies in the capture of industrial, technical, and scientific secrets. Even during the war American and British scientists and technicians gained access to German factories, questioned German personnel, studied German documents, and endeavored generally to keep pace with new discoveries in science, industrial technology, and process development. Under various agencies this work continued for two years after the war. Altogether at least 600 American scientists and industrialists have gone to Germany and brought back reports and several times as many British, Canadian, and. Australian investigators have been similarly engaged under co-operative arrangements designed to assure the maximum of coverage with a minimum duplication of effort. As a result of these investigations and document studies, about 500 or 600 reports have been prepared on metallurgical and allied subjects. Those by American authors or joint teams have been listed in the annotated Bibliography of Scientific and Industrial Reports, issued by the Office of Technical Services in the U. S. Department of Commerce. Many of the British reports are also available in this country through the same office or through a British representative in New York. Since it was my duty to read most of these reports for

Jan 1, 1948

By J. R. Morison, M. P. O’Brein, J. W. Johnson, S. A. Schaaf

The force exerted by unbroken surface waves on a cylindrical object, such as a pile, which extends from the bottom upward above the wave crest, is made up of two components, namely: 1. A drag force proportional to the square of the velocity which may be represented by a drag coefficient having substantially the same value as for steady flow, and 2. A virtual mass force proportional to the horizontal component of the accelerative force exerted on the mass of water displaced by the pile. These relationships follow directly from wave theory and have been confirmed by measurements in the Fluid Mechanics Laboratory of the University of California, Berkeley. The maximum force exerted by breakers or incipient breakers is impulsive in nature, reaching a value much greater than that produced by unbroken waves but enduring for only a short time interval. This impulsive force represents the ultimate development of the accelerative force and is produced by the steep wave front and large horizontal acceleration at the front of a breaker. This impulsive force greatly exceed. the drag force computed from the particle velocities of the breaker. The reader is cautioned that these preliminary results are applicable only to single piles without bracing and are likely to be modified somewhat where multiple piles are driven, one within the influence of the other or where multiple piles are connected by submerged bracing. This paper is essentially a preliminary report submitted at this time because of the current importance of wave forces in the design of offshore structures. An extended series of additional experiments is planned for the near future. Theoretical Relationships For the sake of simplicity of treatment, the theory will be developed from the equations for waves of small amplitude. The horizontal displacement of a water particle is described by the equation 2p cosh — (d + z) H L 2pt X =----------------------sin ----- . , (1) 2 2pD T sinh------ L The horizontal component of the orbital velocity is obtained by differentiation with respect to time as 2p cosh — (d + z) pH L 2pt u = ------------------- cos— .... (2) sinh- L The acceleration of the water particles at any position is obtained by again differentiating with respect to time as 2p cosh — (d + z) 9 u -2vH L 2pt -----=----------------------------sin ----- . . (3) 3 t T2 2pd T sinh------ L where H = wave height — ft L = wave length — ft d = still water depth — ft z = depth below the still water measured negatively downward — ft. T = wave period — sec t = time — sec The force exerted on a differential section, dz, in length is pD2 s u pD 1 dF= [CM (p/4) st + Cn/2 u2] dz • • (4) where D = pile diameter — ft p = water mass density — slugs/ft3 C, = coefficient of mass C,, = coefficient of drag Substituting for a s u/s t arid u2 from Eqs. (3) and (2), the force per unit length at any position z is dF p2 pD H2 &apos; / = — [- fM sin ? ± fD cos2 ? ] . . . (5) dz 2T2 fM D fD 2pt Cm = pA/H:CD = A2;? = T [+ cos2 ? for 0 < ? < p/2 cosh— (d+z) 3p L — < o < 2p Sin L -cos2 ? for p/2 <? <3p/2 The sin 9 term (inertia) i- negative for 0 < 0 < p and positive for p < ? < 2p. Values of A and A&apos; appear in Fig. 1

Jan 1, 1950

By Tasuku Fuwa, John Chipman

Equilibrium data on the reactions of gases with carbon and oxygen dissolved in liquid iron are reviewed and correlated. A source of error in oxygen analysis of graphitic samples is exposed. New experimental data on the oxygen content of high -carbon iron in equilibrium with carbon monoxide indicate that the activity coefficient of oxygen is decreased by additions of carbon. The carbon-oxygen product decreases slightly with increasing carbon content. In recent years a number of investigations have been reported dealing with the equilibria between carbon and oxygen in liquid iron and gases containing carbon oxides. The laboratory study of these reactions dates back to 1931 with the publication of a paper by Vacher and Hamilton&apos; on "The Carbon-Oxygen Equilibrium in Liquid Iron". The principal object of this study was to obtain data on the reaction shown by Eq. [3] below; their data and others by vacherZ permit evaluation of the other equilibrium constants as well. Subsequent studies have been reported by Matoba, Phragmen and Kalling and by Marshall and Chipman.5 The equilibria may be expressed by the following three equations: C + CO,= 2CO;Kl = Pc° [1] 0-+CO = CO,;K2=-P co, "0.PCO c + O = CO; K3 = In the equilibrium constants, ac and a0 are taken as equal to [% C] and [% 0] respectively in the infinitely dilute solution. At finite concentrations an activity coefficient is introduced such that ac =fc [%C], and so forth. It is to be noted that these equations represent only two independent relations, the third being derivable from any two. Richardson and Dennis have determined the conditions of equilibrium in reaction [I] at temperatures of 1560" to 1760°C. Their results have been confirmed by Rist and chipman7 who have shown how the data may be extended to cover the entire range of liquid compositions at temperatures from the eutectic up to 1760°C. An approximate confirmation has been reported by Fuwa and chipman.&apos; These investigations also established the activity coefficient of carbon which was shown to increase rather rapidly with increasing concentration. For the very dilute solutions the value of Kl is expressed in the equation: log^i = - 7280/T+ 6.65 This equation leads to a value of Kl = 430 at 1540° C in excellent agreement with the average value of Marshall and Chipman.5 It is shown as line 1 in Fig. 1 together with the experimental observations. In the case of reaction [2] the direct experimental results can be supplemented by observations on the corresponding reaction with hydrogen, namely reaction [4]:

Jan 1, 1961

By Davis M. Lapham

Ore bodies at Cornwall, Pennsylvania, have been mined since 1742 principally for iron from magnetite, but also for copper (in chalcopyrite), silver (in chalcopyrite), gold (in chalcopyrite), cobalt (in pyrite), sulfur, and crushed limestone aggregate. Metallization occurs as a limestone replacement above the essentially conformable, south dipping portion of a discordant saucershaped diabase sheet. Pre-Triassic and Triassic faulting have emplaced host Cambrian limestone and two Ordovician(?) hornfels units, now for the most part resting above diabase. Thermal metamorphism of carbonate-bearing country rocks largely to calc-silicates, is ubiquitous. Metasomatism, particularly of potassium, is unique to ore zones. Associated magnetite- actinolite mineralization replaces, in a preferential sequence, all earlier metamorphic and metasomatic minerals and rarely diabase chilled margin. Mineralogical (diopside, actinolite, mica, sulfides, oxides) and chemical (Fe, Cu, S, Co) zoning of the eastern ore body is focused down dip, near its western edge, along a major vertical fault through diabase. This zoning is spatially related to magnetite veins in diabase, to an ore body within diabase, and to a shear zone that probably extends through the sheet.

Jan 1, 1968

By C. A. Heberlein

C. A. HEBERLEIN,* New York, N. Y.-The results stated by Rey and Brevers are so startling that they are of great interest, as the concentration of a low percentage of cinnabar by differential flotation yields a high-grade concentrate in the presence of either arsenical or iron pyrite. The authors say: "Cyanide can thus be used to depress arsenopyrite and make a good cinnabar-arsenopyrite separation. A cinnabarpyrite separation could probably be effected in the same way." Corrosive sublimate at the present price of mercury would be a very expensive reagent but the expense would be justifiable if a high rate of concentration could be obtained with a high extraction. On my request, special tests were made in the Punitaqui mill in Chile along the line suggested by the authors, without any improvement of either grade or extraction. As the recovery of the cinnabar in a complex sulphide of chalcopyrite and pyrite gave unsatisfactory results, I had tests made at the testing laboratory of the American Cyanamid Co. at Stamford, Conn. As these tests turned out to be highly satisfactory, not only at Stamford but later at the mine, they are presented here. [AMERICAN CYANAMID TEST FEED PER CENT Si02 66.54 A12032.08 CaO0.70 MgO 0.00 Alkalis1.78 Fe15.63 Cu0.44 S9.42 Hg0.45 OZ. PER TON Ag0.95 Au0.151 Screen Analysis of Tailings, Per Cent Plus650.0 Plus 1001.32 Plus 15020.75 Plus 20019.85 Minus 20058.08] The pulp had a density of 22 and a pH of 7.8. Total time of conditioning was one minute. The reagent added was Texas fuel oil, 0.116lb. Of 33.7 Bé. gravity containing 0.9 per cent sulphur. Frother, 0.062 lb. of No. 5 pine oil. Rate of concentration of mercury was 25.7: 1 [ ]

Jan 1, 1941