Search Documents

By Rodrigo Alberto Moreira Gomes

Uma planta piloto de 600 kW térmicos implantada para avaliar e testar vários combustíveis líquidos e sólidos foi utilizada para avaliação do desempenho de queima de dois tipos de biocombustíveis líquidos em chama oxidante e redutora. Os testes contaram com a parceria entre a Votorantim Metais e a EMBRAPII. Foram avaliados nestas condições de queima quatro biocombustíveis líquidos derivados de óleo vegetal e de pirólise rápida de biomassa. Os resultados mostraram que os óleos avaliados apresentam excelente desempenho em chama oxidante permitindo o ajuste de ar e temperatura de entrada do combustível para otimizar a queima, podendo os mesmos serem utilizados em processos industriais.

Jul 31, 2018

By Gil Ribeiro Vilela Neto

Na busca por se tornar cada vez mais sustentável, a indústria mineral vem recorrendo às soluções tecnológicas que minimizem o impacto ambiental gerado pela disposição dos rejeitos resultantes dos processos de beneficiamento de minérios. Neste cenário, umas das soluções é a aplicação de tecnologias de separação sólido-líquido com o objetivo de maximizar o desaguamento dos rejeitos e, consequentemente, diminuir o volume ocupado por eles quando dispostos e aumentar a recirculação de água. Este trabalho tem como objetivo, determinar a influência da concentração de sólidos em polpas de rejeitos denominados de “lamas” no desempenho do espessamento e a determinação da concentração de sólidos ótima para atingir o melhor desempenho do espessador.

Aug 16, 2017

By Otaviano Donizeti Valadão de Freitas

Ruídos elétricos afetam os circuitos lógicos e conseqüentemente podem comprometer a confiabilidade nos controles de processos, e para minimizar as influências desses ruídos, algumas medidas básicas foram tomadas, com instalações adequadas de todo o sistema, como padronização do aterramento, encaminhamento de cabos, etc. Depois que as medidas foram implementadas, o resultado foi um sistema mais confiável. Se apenas um fio for encaminhado de forma incorreta ou se o aterramento estiver inadequado, pode ser suficiente para causar problemas. A experiência mostra que é muito difícil que todas as medidas sejam aplicadas integralmente, mas se não forem tomadas pelo menos as medidas básicas, o sistema ficará suscetível.

Sep 25, 2017

By Tamilis Rodrigues Braga

Embora a indústria de fundição recicle toda espécie de sucata metálica, usada como matéria-prima no processo, é uma grande geradora de resíduos sólidos, devido, principalmente, à elevada quantidade de areia empregada no processo. As fundições precisam adotar alternativas que minimizem o descarte das areias. A reciclagem interna, por meio da recuperação mecânica, se estabelece como uma opção com benefícios econômicos e ambientais. Neste trabalho foi avaliada a influência da utilização da areia de cura a frio recuperada nas propriedades mecânicas do molde e no acabamento do fundido. Verificou-se que é possível a utilização de até 50% de areia recuperada no processo de moldagem, mantendo propriedades adequadas de desempenho.

Oct 30, 2017

By William Lemos Bevilaqua

No presente trabalho foi avaliado, por meio de ensaios dinamométricos em um motor de combustão interna, o desempenho dos anéis de compressão em diferentes materiais de camisa de cilindro, sob alto regime de carga. Dois materiais foram utilizados nas camisas: Ferro fundido cinzento e um revestimento eletrodepositado de Níquel carbeto de silício. Os ensaios tiveram duração de quatro horas com cada configuração anéis/camisa. Parâmetros de análise, como a rugosidade média (Ra) e o aspecto superficial foram aferidos antes e após os testes. Os resultados apontam que o primeiro anel ensaiado na camisa revestida de Ni-SiC apresentou maior redução de Ra na condição estudada.

Aug 16, 2017

By Luiz Antônio da Silva

Este trabalho tem como objetivo apresentar os resultados do procedimento de geração de energia elétrica adicional a geração econômica na CTE2 com gás natural, visando a redução de custo no grupo CSN.O estudo foi efetuado através da avaliação dos preços do mercado de curto prazo de energia elétrica e análise do processo de geração da planta, aos quais permitiram diagnosticar as melhores praticas e definir a melhor configuração operacional.Os resultados apresentados foram significativos para as condições de operação, o que representa redução do custo de energia elétrica para o grupo CSN e aumento da segurança operacional da planta da CTE2.

Jul 31, 2018

By Amanda Cristina Medeiros da Silva

Este trabalho tem o propósito de avaliar a temperabilidade de um aço SAE 1040 através da utilização do ensaio Jominy e posteriormente promover tratamentos térmicos, gerando nos corpos de prova condições de arrefecimento diferenciadas para avaliar a influência da severidade de têmpera da salmoura e óleo. A curva de ensaio Jominy gerada apresentou um comportamento coerente para um aço com médio teor carbono. Já os tratamentos térmicos que foram realizados posteriormente revelaram que o meio que gera o maior acréscimo nas propriedades mecânicas é o resfriamento em salmoura, haja vista que os corpos de prova submetidos a este resfriamento apresentaram o maior de dureza.

Aug 16, 2017

By Leandro Mendes Pinto

Este artigo apresenta um estudo de analise da viabilidade da substituição de 1 motor padrão utilizado em uma torre de resfriamento por 1 motor de alto rendimento Premium acionado por um Inversor de frequência interligado ao controlador de temperatura. Nas Torres de Resfriamento, ao implantar uma solução que pode a variar a velocidade dos ventiladores de acordo com a temperatura ambiente e a exigência de resfriamento do processo, pode-se obter grandes ganhos em economia de energia. Neste cenário, os motores elétricos têm papel determinante pelo amplo uso na indústria devido a sua versatilidade e eficácia. Por isso, melhorias e inovações são sempre necessárias para otimizar processos e aumentar a lucratividade.

Sep 25, 2017

By Leandro Scheffer Cipriani

A microestrutura e as propriedades mecânicas de um aço de alta resistência submetido a resfriamento rápido empregando equipamentos (Roller Quench e CLC - Continuous On-Line Control), presentes na linha de laminação a quente da Usina de Ipatinga – Usiminas, foram avaliadas nesse estudo. A microestrutura obtida foi composta por bainita e ferrita, com frações desses constituintes variando em função do equipamento utilizado. Devido a essa diferença, os valores de limite de escoamento e de resistência foram maiores no aço submetido a resfriamento via CLC. O resfriamento imposto via Roller Quench propiciou ao aço uma maior tenacidade, medida pela energia absorvida em ensaio de impacto Charpy.

Oct 30, 2017

By Pedro Cunha Alves, Wagner Viana Bielefeldt, Vinicius Cardoso da Rocha, Augusto Lachini Pereira, Julio Aníbal Morales Pereira

The capacity of steelmaking slags (CaO-SiO2-Al2O3-MgO) on inclusion removal from liquid steel was investigated through experimental conditions. Laboratory experiments with slag and steel samples (with inclusion population known) were performed using a vertical electric resistance furnace at 1600 ºC. After the melting experiments, slag and steel samples were separated and analyzed regarding their chemical composition and inclusion population evolution. The capacity of slags on inclusion removal was evaluated based on the thermodynamics (solid and liquid phases proportion, phase composition and effective viscosity of slags) calculated using the FactSageTM 7.2. Results indicated that changes in the composition of slags (regarding CaO/SiO2 e Al2O3) presented effects on the steel cleanliness. The total inclusion density decreased in all steel samples and the removal of inclusions by slags shows a tendency to improve as their viscosity decreases (< 0.23 Pa.s).

Oct 1, 2019

By Werner Klein

The utilization of production facilities in an optimum way, with reliable due date fulfillment, reducing raw material and energy consumption, are challenges iron and steel companies are facing in their business every day. By using an APS system such goals can be achieved to increase the competiveness of iron and steel producers. A sophisticated APS supports the overall planning process by applying complex rules based on product and order mix, its production routings with corresponding processing and transport times and resource availability. Specific technological as well as steel grade and energy related constraints are also considered to meet company specific KPIs. A core feature of APS solution is to react online on deviations to plan during the production process. Deviations such as nonconformance of intermediate material attached to an order, sudden production delays, unavailability of important production resources, makes it necessary to update the production plan. In general the task of APS is to support the preferred work-to-order concept, by assigning work-orders to available production facilities along the product specific process route and generate optimized material sequences for critical work centers.

Aug 17, 2017

By Melina Gamis da Silva

A evolução microestrutural que ocorre durante o processo de laminação a quente pode ser modelada em termos dos tamanhos de grão da austenita e de suas frações recristalizadas ao longo dos passes. Este artigo apresenta uma metodologia que permite a análise da cinética de recristalização e precipitação durante a laminação, com base na composição química do aço e parâmetros do processo. Essa metodologia pode ser utilizada na criação de modelos computacionais. Neste trabalho, as simulações apontaram para a alteração do teor de Nb e da temperatura de reaquecimento da placa como solução para otimizar o processo, resultando em melhorias no produto, ganho de produtividade e redução de custos.

Aug 16, 2017

By Fábio Dian Murari, Antônio Adel dos Santos

The effect of reheating temperature of slabs on the precipitates dissolution and mechanical properties of Ti-Nb microalloyed steel was investigated in pilot scale. It was verified, by means of transmission electron microscopy, a significant decrease in precipitates formed during the solidification of the steel as the reheating temperature increased from 1100°C to 1200°C. No significant changes in size and shape of the precipitates were observed with further temperature increase up to 1280°C. In line with the precipitates dissolution behavior, an increase in strength was observed with the elevation of the reheating temperature up to 1200°C, due in part to the reprecipitation of fine Nb-rich precipitates during the hot rolling. At 1200°C the presence of deformed ferrite on the microstructure contributed to the additional increase in strength. After reheating above 1200°C up to 1280°C, a decrease in strength of the rolled plates was noticed. This effect has been credited to the absence of deformed ferrite grains and also to a small increase in the low angle grain boundaries size. The results were in agreement with Thermo-Calc and Dictra simulations.

Oct 1, 2019

By Andreas Jungbauer

Two Arvedi ESP plants going into operation in 2015 will allow a Chinese steel producer to better serve the extremely attractive local and export markets for high-quality, thin-gauge strip products. The energy consumption and the related costs are reduced by up to 45% compared to conventional casting and rolling processes. This also means a major reduction in CO2 emissions. The new plants are designed for an annual production capacity of 2 x 2.55 million tons of high-quality, ultra-thin, hot-rolled strip products with widths of up to 1,600 mm and thicknesses down to 0.8 mm. The project scope also features a comprehensive training and assistance package for plant start-up and operations by personnel from the existing ESP plant at Acciaieria Arvedi SpA, Italy. The plant setup, the trainings and assistance program as well as latest results from the ESP plant in Italy will be presented. While this project is under execution three further ESP lines have been ordered by the same customer summing up now to five ESP lines at the same location.

Jul 30, 2018

By Patrícia Mundim Campos Faria

The process of particle size reduction by grinding is inherently inefficient and involves high capital and operating costs. In particular, ball milling is one of the important unit operations in the iron ore pelletizing process. The mill product, due to its physical properties, determines the efficiency of subsequent stages of classification, filtration and pelletizing, thus impacting the quality of iron ore pellets. The work demonstrates the application of the population balance model in the optimization of a full-scale ball mil circuit grinding pellet fines with the aim to evaluate the optimal solids concentration to improve iron ore pellet quality. Initially, detailed experimentation was carried out in a 25.4 cm diameter batch mill and a relationship for mill scale-up using a linear population balance model in wet grinding systems was established. The selection and breakage parameters and the specific selection functions were determined for pellet feed iron ore. It was possible to identify the non-normalizable nature of the breakage functions of the ore studied, which were modeled properly. Afterwards, as a result of incorporating the specific selection functions and breakage functions into the linear population balance model, it was possible to predict product size distributions in the pilot and plant scale mills (0.416 and 5.18 m diameter, respectively) from data obtained in the 25.4 cm diameter mill. Finally, with this scale-up procedure it was possible to appraise the plant scale optimization via laboratory scale grinding mill tests. The effects of changing percent solids were assessed in order to improve the industrial mill performance and the optimal value should be in the range from 76 to 80%.

Aug 1, 2018

By Elham Kordzadeh

As the world’s reserves of coarse and high-grade iron ores continue to shrink, beneficiation is becoming increasingly important. The resulting concentrates cannot be used directly as feedstock for iron making, but require an additional agglomeration step. Pelletizing is preferred, because the uniform chemical, physical, and metallurgical characteristics of pellets make them a more desirable feed for the iron making processes. The heat hardening or induration of pellets is typically done in shaft furnaces, grate-kiln systems or on straight grates. Rotary kilns were originally developed in the late 19th century for Portland cement production [1]. The main development work for the successful adaptation of the process to the thermal treatment (induration) of green balls from iron ore was performed by Allis Chalmers in Milwaukee, Wisconsin, USA in the 1960’s [2].The straight grate process, which was first used in 1955 at Silver Bay, Minnesota, was a dedicated development with the aim to pelletize and indurate magnetite (taconite) concentrate [2]. There are various important technical and economical distinctions between the two pelletizing technologies. The most important differences include that a grate-kiln has three distinct pieces of equipment, a preheat grate, a rotary kiln and an annular cooler, whereas in the case of a straight grate, the entire indurating process is done on one piece of equipment only. In addition, both technological solutions have differences in their recuperation systems, direction of air flow in drying, number of burners, form of pellet movement, etc., which cause differences in raw material suitability, process control, economical aspects, plant operation and product pellet quality.

Oct 30, 2017

By Kyle T. Chomyn

Multi-disciplinary engineering analysis and advanced modeling techniques were used to identify and develop low cost design modifications to improve a blast furnace hot blast air distribution main that experienced frequent refractory failures. Piping flexibility analysis helped identify the root causes of refractory damage and determine the need for new expansion joints. Finite element analysis was used to optimize a custom-designed elbow-to-elbow tie-rod system, which ensures thermal expansion loads are not placed on connecting piping. Heat transfer coefficients through the elbows were estimated using computational fluid dynamics (CFD) flow modeling. The cast refractory design was changed to a more reliable brick refractory design. Excessive draft was occurring during furnace back-drafting, so the system was assessed using CFD, and a passive flow-reduction spool was designed. This firstprinciples engineering design approach allowed for optimization and verification, ensuring that the new design addressed the root cause of the previous deficiencies.

Aug 17, 2017

By Dr. Steven G. Jansto

The market demand for reduced fuel consumption and CO2 emissions in the automotive, energy and construction sectors have further increased the demand for new and advanced higher quality microalloyed grades produced via TMCP. The technological integration of the process and physical metallurgical advancements of value-added niobium (Nb) microalloyed thermo-mechanical controlled process (TMCP) steels continue to be developed and is an important element for these more demanding end user requirements and cost-effective steel production. The reheat furnace process step has a profound effect on the TMCP performance, final hot rolled steel quality and mechanical property consistency during the production of hot rolled steels. The uniformity of heating applied across the entire width, thickness and length of the slab or billet is essential in the successful achievement of consistent customer properties regardless of the chemistry. The resultant ferrite grain size in the final hot rolled product is significantly governed by the initial prior austenite grain size. However, the transition from laboratory melted and TMCP hot rolled heats to the production scale is often quite challenging. Aberrations in the reheating process step at the industrial furnace are often the root cause of mechanical property quality issues. These combustion process metallurgy parameters connect directly to the resultant TMCP product quality and is defined as Combustion Metallurgy

Oct 1, 2019

By Silvio Cecchini

State-of-the Art Mould Level Control Solutions for continuous casting applications face different challenges. On the one hand, technological phenomena such as clogging and unclogging, unsteady bulging or waving can create unpredicted meniscus disturbances by completely changing the casting channel geometry and the flow behaviour of liquid steel to the mould. On the other hand, from the viewpoint of caster operations, long lifetime, quick interchange-ability and integration capability into existing systems must be achieved. In the present contribution, the overall development of INTECO TBR’s mould level master – a comprehensive mould level control solution for all continuous casting applications – will be introduced. The basis for the presented system is a development over several years which includes investigations of all critical components such as shroud, stopper, stopper mechanism, servo actuator and mould level control program. These investigations finally resulted in a new-ly developed control algorithm for a highly dynamic servo actuator. The control algorithm with its basic functionality such as the prevention, identification and removal of clogging impacts with the associated automation functions to reduce their influence onto the overall mould level control performance will be presented. The scientific basis, the resulting control functions and their related automation implementation will also be illustrated. Finally, a patented control algorithm and control functionality for unsteady bulging and waving effects with the associated automation functions to reduce their influence onto the overall mould level control performance.

Aug 16, 2017

By Günther Staudinge

Aperam is a global player in producing of stainless, electrical and special steel qualities. The steelmaking plant in Timoteo Brasil is equipped with one AODconverter for stainless steel and one MRPL-converter for special steel production. After almost 20 years of operation Aperam decided to exchange the existing 80 t MRP-L converter by a new one including a new trunnion ring and a state of the art suspension system. Due to an optimized design the inner volume of the new converter could be increased which comes along with improved production. A special feature is a flange connection in the barrel section of the converter. This allowed to avoid any critical site welding and the time between shut down of the old and cold commissioning of the new converter could be done with 17 days only.

Aug 17, 2017