Search Documents

By Giuliana A. Zelada-Tumialan

Reduced workability and flowability of the concrete through the tremie tubes and drilled shaft reinforcement have been identified as the main causes of tremie-concrete drilled shaft concrete defects. This paper discusses two recent case studies of defective tremie-concrete drilled shafts. The defects (soft inclusions, aggregate segregation, and low concrete strength) were primarily caused by the combined effects of the tremie placing sequence, rapid concrete slump loss, and poor passing and blocking characteristics of the approved concrete mix design. The level of detail contained in the drilled shaft specifications varied between projects. However, even when the specifications incorporated several of the more recent recommendations for tremie-concrete placement, the case studies showed that typical provisions for concrete mix proportioning and placement can be further improved to minimize construction defects such as those described in this paper. Based on the findings of the case studies presented, recommendations for the development of more effective specifications are provided. The recommendations include requirements for mock-up testing of proposed concrete mix designs and evaluation of the tremie-concrete placement sequence. Performance of such testing and evaluation would greatly reduce the potential for drilled shaft defects and consequent time and financial burdens associated with them.

Jan 1, 2009

By Forrest T. Moyer

The National Safety Competition was inaugurated in 1925 by the Bureau of Mines, U.S. Department of the Interior, in cooperation with the Explosives Engineer. In the first nationwide contest, 210 mines and quarries were enrolled. In 1962, the thirty-eighth anniversary of the competition, 910 mines and quarries were enrolled. These participating plants were worked a total of 133,292,989 man-hours. Of the enrolled plants, 415 achieved injury-free operations for the year, the largest number of perfect safety records in the history of the contest.

Jan 1, 1964

By J. J. Jakosky, D. H. Zellers

"IntroductionThis paper is the seventh of a series describing an investigation being conducted by the Bureau of Mines on underground communication. A review of past work and results obtained has been published. The present paper deals with a study of line-radio or wired-wireless methods of communication, herein electrical energy is transmitted by metallic conductors.The use of line-radio over metallic conductors has been practiced for a number of years, and at present is being used on a large scale in long-distance carrier-current telephone and telegraph. The early work of the U. S. Army Signal Corps and the Bureau of Standards in using ordinary radio transmitting and receiving apparatus for communication over metallic conductors was been descried. Later publications describe commercial applications, and an excellent treatise and resume is given by E. Colpitts and C. B. Blackwell.Scope of ReportThis report contains (1) a discussion of the chief factors affecting carrier-current transmission, with particular reference in application to underground communication for mines; (2) a description of typical underground circuits used for power and lighting; and (3) description of apparatus used and results obtained in line-radio experiments in coal mines near Pittsburgh, with circuit diagrams, and conclusions as to power requirements and limitations for mine use."

Apr 1, 1925

By L. Bruce McDonald

This Federal Bureau of Mines publication is a statistical analysis of all surface and underground coal mine fires reported in the United States from 1950 to 1977. Accounts of selected nonreportable fires and opinion data gathered via interviews with mine safety directors were separately analyzed. Both reported and nonreportable fires were analyzed by time trends, State, ignition source, burning substance, location in mine, equipment, detection, duration, injuries, fatalities, and successful extinguishing agents. It was found that the majority of all mine fires were electrical in origin. The equipment most frequently involved in underground fires was conveyor belts, and in surface fires, it was crushers and/or breakers. Underground fires occurred most often near the working face. Water and hand-portable extinguishers were the most common methods of extinguishment.

Jan 1, 1980

By Stephen Tadolini

The annulus thickness, for bolts anchored with resin, effects the systems final performance. Recent developments in the manufacturing process of these support systems, coupled with improved resin characteristics, have resulted in design changes to minimize hole drilling requirements and reduce resin usage. The amount of resin to properly anchor a 7/8-SRD (Special Rolled Dimensions) bolt in a 25.4 mm (1-in) diameter hole has been reduced to about one-third of the resin required to anchor a No. 7 rebar bolt (22 mm (7/8-in) diameter) traditionally installed in a 35 mm (1-3/8-in) diameter borehole. More importantly, laboratory and field tests, indicate that higher bond strengths and anchorage capacities can be realized with reduced annulus systems. These factors have a direct bearing on reinforcement efficiency and subsequent roof support performance.

Jan 1, 1998

By F. J. Plaul

The dominating technologies for steelmaking are the basic oxygen furnace (BOF or LD process, Linz-Donawitz) and the electric-arc furnace (EAF). The main iron input materials for both are liquid iron as hot metal, or solid iron as pig iron, DRI (direct reduced iron), HBI (hot briquetted iron) and scrap. Hot metal, pig iron (i.e., solidified hot metal) and DRI/HBI are virgin iron materials, which have to be produced from iron ore by so-called ironmaking technologies. The family of ironmaking technologies includes three process routes: blast furnace, smelting reduction and direct reduction. Driven by steadily increasing costs of raw materials in the last two decades, the sector has seen a number of new developments in ironmaking technologies, developments based on fluidized-bed technology. The main advantage of a fluidized-bed technology is that fine iron ore can be directly charged to the process without prior treatment; it does away with agglomeration and its concomitant cost, a step practised in blast-furnace, COREX® and MIDREX® processes. With Posco of South Korea, Siemens VAI Metals Technologies has successfully developed the FINEX® process, a smelting reduction based on the direct use of iron ore fines to produce hot metal. The key technology is the four-stage, bubbling fluidized-bed-reactor system, in which fine iron ore is reduced to DRI fines in a countercurrent flow with a reducing gas generated by coal gasification. Beside surveying the current state of the art, this paper discusses the technological principles of smelting-reduction and direct-reduction processes. The status of FINEX® and the outlook for further developments are described. Crucial to the successful development of the new ironmaking technologies for the direct use of fine ore was the scaling up of the fluidized-bed reactor system, which demonstrated new design features.

Jan 1, 2009

By Eugene Mirsky, Eloy Ramos, May ElKhattab, John Wise, Terrence Carroll, Jose Torres

In 2017, Nicholson Construction Company completed a $72.1 million design-build contract for Miami Dade Water and Sewer Department to replace an existing 54-inch diameter pre-stressed concrete force main that runs from the Virginia Key Central District Wastewater Treatment Plant, under the Biscayne Bay at Norris Cut, to Fisher Island. In order to install the new sewer pipe below the bottom of Biscayne Bay, a tunnel boring machine (TBM) was launched from a 42ft diameter and 89ft deep shaft on Virginia Key and a precast segmentally lined tunnel was constructed towards a 28ft diameter and 72ft deep retrieval shaft on Fisher Island. Both shafts were constructed through sand and highly permeable limestone, primarily the Fort Thompson Formation which is part of one of the most permeable aquifers in the United States and two different techniques were used to ensure a water-tight shaft at each end of the tunnel drive. The launch shaft structure was built using the secant pile technique, wet excavation and a tremie plug. For the tunnel break-in a soil freeze block was installed after the ground was treated with low mobility grout. The retrieval shaft was built using the Deep Soil Mixing (DSM) technique and excavated in the dry. Precedence of any other structure built this deep through hard layers (UCS over 3,000 psi) using this technique was not found. This case study addresses the challenges of constructing watertight underground structures in highly porous ground for launching and retrieving a TBM. Design challenges from complex asymmetric loading, selection and comparison of the construction techniques, the installation and excavation of both shafts, and their performance are also discussed herein.

Jan 1, 2018

The commercial application of electrolysis to zinc sulphate solutions for the production of metallic zinc is a development ·of the past twenty years. Earlier attempts failed to give satisfactory results, chiefly because certain harmful elements were either not recognised as being present in the solution, or, if recognised, suitable methods of removal had not been developed. The electrodeposition of zinc from zinc sulphate solution is extremely sensitive to the influence of a great many factors, all of which appear to be closely inter-related.Some of these factors tend to minimise the necessity for a high degree of purity of the solution, while other factors aggravate the harmful nature of certain impurities.The relationship existing betweBn the various factors in zinc electrolysis makes a general discussion of the injurious effect of impurities very difficult since, under one set of conditions a given concentration of an impurity may be of minor: importance, where its under another set of conditions the same concentration of that impurity may prove dangerous to successful electrolysis.

Jan 1, 1934

By Kerry Spickelmier

Editor's note: information for this feature was taken from the published APCOM proceedings. Computer trends, with special focus on the reasons for computer use, grabbed the lion's share of attention at the 23rd worldwide meeting on the Application of Computers and Operations Research in the Mineral Industry (APCOM 23). However, technical topics did not provide the meeting's sole focus. The last-minute inability of certain former communist countries to fund the travels of a few scheduled speakers was a reminder that science does not operate in a void. As with all technical progress, the APCOM presentations raised interesting questions regarding interrelated organizational dynamics and political and socioeconomic issues. Consider US Bureau of Mines (USBM) research to design an expert control systems to "duplicate" an experienced, "good" operator during automated underground roof bolting. In his presentation of the project, Takach, Jr. stressed the importance of preserving the ability to switch from automatic to manual drilling control. From a technical standpoint, this allows the expert system to "learn" from a good operator. As important, he said, is that this flexibility decreases the human operator's sense of being replaced by the machine. The question arises: Which will loom larger in union minds, increased operator safety through remote opera¬tion or the potential for total operator replacement? Like any new product, computer technology relies on marketing to aid its acceptance and use. Consider, too, a decision support system, by Schena and Gochin, for mineral resource management in a developing country. The authors said "the analysis permits the assessment of the overall socioeconomic consequences of mineral prospects and allows incorpo-

Jan 1, 1992

By G. Melcher

"A través de la introducción del proceso de flotación, el horno de cuba perdió su importancia como unidad de fusión en la metalurgia del cobre. El producto obtenido mediante este proceso de tratamiento de minerales constituye un concentrado de flotación de granulometría extremadamente fina. En ese sentido, el presente texto señala un proceso de fusión en el cual el combustible natural del concentrado: el azufre, se utiliza para el trabajo de fusión. Asimismo, la tostación y la fusión se realizan en una sola unidad de horno y la gran superficie natural del concentrado de flotación, se aprovecha para la fusión, de modo que el concentrado sea tostado en suspensión y al mismo tiempo, fundido. Finalmente, la cantidad de los gases que reaccionan con los sólidos, puede aumentar considerablemente y, por lo tanto, igualmente la velocidad de reacción. "

May 1, 1979

In this paper, the authors attempt to apply a simplified non-homogeneous void diffusion model (NHVDM) to predict surface subsidence for longwall mining in Illinois. A generalized error function subsidence profile is derived from this model. The model validation indicates that the NHVDM approach appears to fit the observed subsidence data as well or better than the error and the trigonometric functions, particularly around the trough edge areas.

Jan 1, 1990

A wide-ranging base of jig data was collected from various types of commercial jigs in 9 coal preparation plants in China, and a complete data analysis was made. It was found that the sharpness ofseparation was very variable, which demonstrates the complex interplay of the many factors which influence jig performance. Tests showed that there exist optimum frequency ranges in each compartment of a jig. Stepwise regression analysis indicated that the sharpness of separation is most sensitive to the intake fraction ofthe air cycle, the frequency, and the feed rate. By means of non-linear curve fitting techniques and statistical analysis, several mathematical models were developed to describe both partition curve and the jig performance, for simulation purposes.

Jan 1, 1986

By A. Moergeli

The Swiss are currently building the world’s longest tunnel, the 35-mile long Gotthard Base Tunnel. At Sedrun, for the first time in tunneling, four Roadway Support Machines will drive through most difficult ground, supporting variable diameters of up to 13 m. The machines are prepared for their first deployment. At Amsteg, two Hard Rock TBMs have successfully crossed a known fault zone by applying full circle steel arches and shotcrete immediately behind the cutter head. Comparisons between Drill& Blast and Hard Rock TBM are shown.

Jan 1, 2005

By S-L. Weeber

Ash fusion temperature is the temperature at which the mineral matter in coal begins to soften, flow and fuse. It is an important parameter relating to coal utilization. Optimum ash fusion temperatures derived from coal in the Witbank Coalfield region are approximately 1400°C, and higher, although temperatures above1300°C may be deemed acceptable. This study attempted to determine which factors, mineralogical or inorganic-chemical, influence variations in the ash fusion temperatures in certain coals. Coal was sampled from the Number 2 coal seam at opencast and underground workings at New Clydesdale Colliery, Witbank Coalfield, South Africa. The samples represented known low and high ash fusion temperature coal. Analyses performed included proximate analyses, calorific value determination, percentage sulphur, ash fusion temperatures, ash analyses (composition of ash), X-ray diffraction, scanning electron microscopy and petrographic studies. Results show that although a complex relationship exists between ash fusion temperature and the various geological and coal parameters, some positive correlative results were obtained. These indicate a possible relationship between low ash fusion temperatures and i) finer size fractions, ii) an increase in iron content present in the form of pyrite and iii) the form in which pyrite is present, namely cleats. High ash fusion temperatures tend to correlate with i) the absence of pyrite or ii) pyrite present as framboids.

Jan 1, 2000

By Y. L. Su, S. Vongpaisal, H. A. Smith

"It is extremely difficult for a mine's central control room operator to control peakpower demands and to maintain normal materials handling operations at the same time. An investigation of the Falconbridge Strathcona Mine 's central control room has revealed that there are more than eight thousand possible combinations of ""situations"" that can arise. For such a circumstance, an expert system can become a very valuable tool to assist the operator in taking the most appropriate and timely action.A forward chaining expert system module has been developed for this application. The module is based on Level 5 ObjectTM software. It is graphics oriented and user-friendly. Training requirement is minimal.ForewordThis paper has arisen out of work carried out by YLS Associates and Falconbridge Limited as part of a contract between Falconbridge and the Department of Energy, Mines and Resources, Government of Canada, on the application of expert systems in mining operations.IntroductionThe electrical bill charged to large consumers by Ontario Hydro is based upon two elements: demand and energy consumption. The demand is the peak kilowatt level that the consumer has required during a monthly period. It is not uncommon for the demand portion to be as much as one third of the monthly bill. Energy consumption is the total kilowatt-hour s (kWh) consumed during the period.Ways to reduce the energy consumption part of the electrical bill involve utilizing energy-efficient equipment and operating machines in off-peak hours when a lower energy rate is charged. Maintaining the peak power below a critical level may require that simultaneous usage of major pieces of equipment be avoided. A 3000 kW skip run at an inopportune time could cost a company an extra $30,000 in that month's power cost.Potential disadvantages associated with peak power control are lost production due to work stoppage and increased operating costs due to the need to employ extra personnel. Most companies find these matters relatively easy to deal with and with incentives provided by Ontario Hydro, actively pursue this facet of energy savings (Harju , 1991)."

Jan 1, 1993

By G. E. Perry, R. D. Seba

The steam soak process is the most widely applied and most successful thermal supplemental recovery process in use today. This process, which consists of injection of steam in various quantities into a well that is subsequently used as a producer, can be repeatedly applied to the same well. The treatment, if successful, will increase the production rate of the well for a given period. For this reason, the steam soak process should be considered primarily as an acceleration method rather than as a method for producing oil that could not be recovered by primary means. However, application of this process to reservoirs containing viscous crude may produce oil that otherwise would have zero present value or would be produced at such low rates by primary methods that it would not be profitable. A major necessity for the successful application of the steam soak process is a source of natural energy. This source of energy may exist in one or more of the following forms: expansion of fluids, compaction, gravity drainage. This study was undertaken to determine the effect of gravity drainage on steam soak production and recovery and to develop a method for predicting production rates, ultimate recovery, and heat requirements when applying this process to a reservoir in which the primary driving mechanism is gravity drainage. (For additional discussion of some of the factors that affect recovery of viscous oils by the steam soak process, see Ref. 5.) Model The model developed for analyzing the performance of the steam soak process in gravity drainage reservoirs is a modified form of that developed by Matthews and Lefkovits.1,2 The model used in this study consists of two concentric cylindrical volumes of productive formation with cap and base rock of impermeable material. The inner cylinder, extending from the radius of the wellbore to some predetermined radius, is referred to as the hot zone; and the outer cylinder extending from the exterior boundary of the hot zone to the outer drainage boundary will be referred to as the partially heated zone. Fig. 1 is a schematic cross-section of the model, indicating its thermal properties. Horizontally the reservoir is divided into two regions, the upper region having a high gas saturation and residual liquid saturation, and the lower region containing a high liquid saturation. The boundary between these two regions is referred to as the free surface, which drops and changes shape as fluid is produced from the reservoir. The model was used to analyze the steam soak process by applying the following assumptions: 1. The horizontal formation is composed of one or more homogeneous noninterconnected layers containing incompressible fluids. Each layer is treated separately. 2. The hot zone is heated by the initial soak and is maintained at the steam temperature corresponding to atmospheric pressure by resoaking. 3. The height of the free surface at the producing well is at all times zero (producing well is pumped off). 4. The position of the free surface at the start of

Jan 1, 1970

By T Grenne, R. B. Larsen

Paper presented at the conference on Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. Paper originally entitled: Processes in a newly discovered sulphide-PGE mineralisation in Norway. The Stormyrplutten mineralisation is hosted by a minor tholeiitic metagabbro of low-Ti composition intruded at a high level in the volcanic lithology. It is thought to be the subvolcanic counterpart of submarine basalts generated during an extensional episode of ensimatic arc evolution. The sulphide-PGE mineralisation occurs as stratabound pyrite, pyrrhotite and chalcopyrite disseminations with average grades of 376 ppb Pd, 313 ppb Pt, 40 ppb Au, 0.5% Cu and 0.08% Ni in a deposit 15-25 m thick. Locally the PGE content peaks at 2 ppm over 1 m. Microprobe analysis isolated 14 different platinum-group minerals, dominated by sperrylite, temagamite and borovskite and occurring as 1-20 micron compounds embedded in the main sulphide minerals or along the sulphide/silicate grain boundaries. Mantle-normalised plots reveal strong depletion in Os, Ir and Ru and enrichment in Pt, Pd, Cu and Au. The general decrease in Pd and Pt and increase in S up through the stratigraphy is similar to PGE distribution in the Darwendale subchamber of the Great Dyke in Zimbabwe, and may reflect strong fractionation of Pd and Pt in favour of the first droplets of sulphide melt; two reversals of the trend at the 4 and 12 metre levels represent replenishment with fresh magma and repetition of the cycle. In contrast to the Darwendale system, Cu and Ni also show peak concentrations in the first-formed liquids and Pt appears to have fractionated more strongly into the sulphide melt than Pd

Aug 1, 1995

By W. L. Falke

The Bureau of Mines has developed a system that permits the "soft" soldering of aluminum and aluminum alloys with standard tin-lead solders. The method employs application of a thin nickel-copper-alloy coating to the substrate, which enables the tin-lead solders to wet readily and spread over the areas to be joined. With conventional technology, aluminum and aluminum alloys are extremely difficult to solder because tenacious surface oxide films prevent wetting. With the Bureau-developed method, the aluminum substrate is mechanically or chemically cleaned to facilitate bonding to a minute layer of zinc that is subsequently applied with an electroless zincate solution. The nickel-copper-alloy (30 to 70 pct Ni) coating is then applied electrolytically over the zinc, using immersion cell or brush-coating techniques. Development of acetate electrolytes has permitted deposition of the proper alloy coatings. The coated areas can then be readily joined with conventional tin-lead solders and fluxes. The joints so formed are ductile, strong, and relatively corrosion resistant, and exhibit strengths equivalent to those formed on copper and brass when the same solders and fluxes are used. The method has also been employed to soft-solder magnesium alloys.

Jan 1, 1983

By Mark S. Sanders

This report presents recommended visibility requirements for continuous miner, shuttle car and scoop operations and details the methodology used to generate them. A task analytic approach was used to define information requirements and visual features which served as sources of information. Information requirements were prioritized and the location of visual features determined. From this analysis, visual attention locations, containing one or more important visual features, were identified. A total of 71 locations-were identified for continuous miners, 54 for shuttle-cars and 54 for scoops. A procedure was developed for assessing whether operators in existing machines could be expected to see the visual attention locations. The procedure makes use of a Human Eye Reference Measurement Instrument (HERMI) designed for this project and an outside-in photographic procedure for documenting compliance with the recommendations. A sample of continuous miners, shuttle cars, and scoops were used to test the procedure. Results are presented in the report.

Jan 1, 1981

By Daryl R. Tweeton

This Bureau of Mines publication ill scribes present practices of making injection wells for in situ uranium leaching. Casings, screens, drilling fluids, coring, logging, cementing, and developing are discussed with the objective of aiding those who are starting an in situ leaching operation. Improper choices of materials or techniques can result in wells that are either useless or wells that have an undesirably high resistance to injection. Important factors include careful selection of screen slot size, use of logs for choosing the cementing basket depth, proper cementing techniques, and careful choice, use, and flushing of drilling fluids. The information was obtained through observation of well construction and through discussion with in situ leaching companies, drillers, and suppliers.

Jan 1, 1978