Search Documents

By Serge Rudchenko

A study to determine the potential use of retaining structures in open pit backfilling. Research and review of the open pit mine environment, mine waste disposal, and past and current use of retaining structures. A development of specific structures, the culvert/ tunnel concept, and an anchor block retaining concept. The cost benefit of retaining structures used for in-pit backfilled waste.

Jan 1, 1981

By Bauduin C. Besix

The Eurocode 7 "Geotechnical Design" is based on "Limit State Design", tackling the uncertainties as much as possible at their source through: - selection of characteristic values of variables (loads, soil properties, pile resistance,...); - partial factors applied on the characteristic values; - model factors to account explicitly for uncertainties of the calculation rule if necessary. Eurocode 7 will propose three "design approaches". The selection of one of them will be by National Determination. For pile design, the approaches are: - approach 1 is a "material factoring approach" at load side and a "resistance factoring approach" at resistance side. The structural and geotechnical design are checked for both of two separate sets of partial factors. - approach 2 is a "load and resistance factoring approach" and is in several aspects close to a deterministic approach. The design is checked for one set of partial factors. - approach 3 is a material factoring approach, at load as well as at resistance side. The design is checked for one set of factors. The aim of this paper is to introduce to the design of pile foundations based on pile load tests and on ground test results (semi-empirical and analytical methods) in the frame-work of the three design approaches. Detailed attention is devoted to: - the selection of the characteristic value of the pile resistance, accounting for spatial variability and stiffness of the structure; - the reliability of the prediction of the pile resistance using analytical or semi-empirical methods which may be accounted for through a "model factor". The results of a large test campaign on screw piles in OC Clay and a calculation example illustrate the proposed procedure when calculation rules using CPT results are used.

Jan 1, 2002

By S. E. Phillipson, P. L. Tyrna

Lineament analysis, a remote sensing application for geological structures, has been criticized for reliance on subjective interpretations. The Mine Safety & Health Administration’s Roof Control Division performs lineament analyses with a technique that removes much subjectivity. Study areas are viewed on satellite images with software that allows examination under artificial sun azimuths and elevations. Extraneous lineaments are removed through successive steps of superposition, resulting in selection of the most robust linear features. Field investigations revealed a strong coincidence of joint and fault zones that were parallel with projected lineaments. The Roof Control Division’s successful identification of lineaments associated with roof falls and highwall failures has prompted some mine managers to incorporate lineament analysis as a mine-planning tool. The identification of potentially hazardous ground conditions will allow mine operators to obviate safety concerns that might otherwise adversely affect miner health and safety.

Jan 1, 2002

By Antônio Peres, Rogério Guimaraes, Lauro Takata, Harold Wyslouzil

"Serrana’s concentrator, in Araxii, has capacity of producing approximately 800,000 tomes of phosphate rock per year, with a P205 grade of 36%, from ores grading between 13% and 14% P205. The annual mining rate is around 3.5 Mt and the apatite is concentrated according to the following sequence: crushing, grinding, desliming, flotation and low and high intensity magnetic separations.Two industrial flotation columns (3.0 m x 4.5 m x 14.5 m) were commissioned in 1993 as a replacement for circuits of barite and apatite fines flotation. In 1994, four additional flotation columns of the same dimensions were put into operation, replacing 42 Wemco mechanical cells (300 ft3 each), in the barite pre-flotation, coarse apatite (two columns) and tailings regrind flotation Circuits. Overall, 66 mechanical cells (300 ft3 each) were replaced by only six flotation columns, designed by Cominco Engineering Services Ltd - CESL.The present paper describes the stages of process development, pilot plant testwork and implementation of the industrial project, highlighting the most relevant aspects of each of them. The results achieved are related to improvements in flotation selectivity, gains in P205 recovery and better process control, resulting in better quality products and lower production costs. Other benefits included a decrease in flotation reagents, electrical energy and maintenance materials consumption. These factors contributed to a significant decrease in the cost of phosphate rock production at Serrana, in Araxa - M G."

Jan 1, 1999

By R. A. Westin

[Polychlorinated biphenyls (PCR's) have been widely utilised as fire-resistant dielectric coolants; in electrical equipment used in mining applicants, including transformers, capacitors, electric motors, and electromagnets. In addition, PCB's have been used in hydraulic fluids and heat-transfer fluids and are present in many oil-filled transformers. The U.S. Environmental Protection Agency (EPA) recently banned the manufacture of PCB's and equipment using PCB's, and imposed strict requirements on the continued use and disposal of existing PCB equipment. This manual discusses the EPA requirements, suggests ways to decrease the risks resulting from continued use of PCR equipment, and surveys the non-PCB equipment that is available as replacements for the PCB electrical equipment presently used in mines.]

Jan 1, 1980

By Daniel Valente Guimarães

Este trabalho tem como objetivo apresentar os resultados alcançados através do planejamento, por meio do agendamento com hora marcada, no processo de expedição de produtos acabados, que estão permitindo a Votorantim Siderurgia atratividade na contratação de veículos, redução de custos e confiabilidade no processo.

Aug 17, 2017

By G. R. Fitterer, E. A. Krockenberger, B. E. Sockman, R. B. Meneilly, J. F. Eckel, E. W. Marshall

"Steel manufacturers have noticed a decided tendency on the part of many of their customers to become more exacting in their steel specifications. Under these conditions, the steel must not only meet the specifications of physical properties (tensile strength, reduction of area, elongation, impact strength, grain size, normality, etc.) and the chemical analyses, but must also pass the inspection test of ""cleanliness.""By cleanliness is commonly meant the absence of oxide and sulphide inclusions. Other foreign particles such as furnace or ladle slag, ladle and runner brick, etc., must also be absent. The determination of cleanliness at present is usually made by microscopic inspection or macroetching.The rejection of steel for lack of cleanliness is increasing, out cleanliness is one of the most difficult requirements for the manufacturer to fill. The reason for this is that every steel inspector has a different conception of a. clean steel. A material which does not pass the examination of one inspector way be regarded as entirely satisfactory by the metallurgist of an¬other company. The cause of this confusion and disagreement concerning the definition of a clean or a dirty steel is simply that as yet no standardized procedure for the determination of impurities has been proposed and generally accepted, since many variables are encountered which interfere with the development of a satisfactory method. An idea of the complexity of this situation will be obtained from the following pages.A Survey of Proposed Analytical MethodsAlthough no analytical method has been accepted, many procedures have been proposed, as may be seen in Table 1. Therein are listed 16 of the better-known processes, pith references to the work of their originators, their mechanisms of determination, and their applicabilities. Among these is included the electrolytic method developed by one of the present authors, and some comparison between this and previously proposed procedures may be obtained by a study of the table. It appears that this new method Las many advantages over the others, and this paper presents a critical Study of its value."

May 1, 1933

By M. G. Maruma

The effect of the amount of cold reduction and annealing temperature on the evolution of the texture of AISI 441 steel is reported. The steel was cold rolled by 62%, 78%, and 82%, followed by isothermal annealing of each sample at 900°C, 950°C, and 1025°C for 3 minutes. The crystallographic texture was determined by Phillips X?Pert PROMPD texture diffractrometer. Microstructures were characterized using optical microscopy and scanning electron microscopy (SEM).The results show that sample that received 78% cold reduction and annealing at 1025°C presented the highest Rm-value and lowest ?R-value, which would enhance its deep-drawing capability. In addition, this sample showed the highest intensity of shifted ?-fibre, notably {554}<225> and {334}<483>. It can therefore be concluded that the ?-fibre, which favours deep drawing, is optimal after 78% cold reduction and annealing at 1025°C.

Jan 1, 2013

By T. Gerritsen, R. C. Delgado, J. Janzen, E. R. Veloza

The paper describes the components of an Integrated Furnace Control system for covered-arc (shielded arc) smelting with results from the recently started 75 MW Cerro Matoso Line 2 Furnace. The paper starts with a review of the mechanisms of power and feed input and heat losses in the shielded-arc smelting process, and describes how the details of the control system are tailored to the process. The control modules of a covered-arc smelting furnace are described including measured results and screen captures. This paper focuses on Integrated Furnace Controls tailored to shielded-arc smelting, but similar approaches have been recently applied to other furnace processes including immersed-arc smelting.

Jan 1, 2004

By C. A. Ozturk

The compressive strength of rock (sc) has an important effect on design of structures in rock engineering. Compressive strength can be determined in the laboratory using the uniaxial compressive strength (UCS) test. Some other index tests, such as the point load test, are also used, particularly when suitable samples for UCS are not available. The quantification of rock texture has introduced a new method in rock engineering for estimating the mechanical and physical properties of rock materials from microscopic investigations. The aim of this study is to quantify rock texture to estimate rock strength from the texture coefficient (TC), which is determined from a statistical assessment of thin section images. Rock texture is quantified by twelve different images from a single thin section to increase the reliability of texture analysis. A data-set is prepared to investigate correlations between TC and sc. The statistical correlations are computed after classifying of the rock samples based on their lithology as well as grain features. Equations derived based on the results of this study are used to predict the approximate value of compressive strength from the texture coefficient. This method is particularly useful for preliminary studies in rock engineering projects prior to detailed site investigation.

Jan 1, 2014

By Robert Gannicott

??A mining company without the burden of operating a mine ??Management focused on marketing a high-quality, run-of-mine range of Canadian diamonds ??Robust revenue stream ??Specialist diamond knowledge ??Canadian exploration and development expertise ??BUT ??Single asset revenue base from depleting ore reserve ??Limited influence on production plans

Apr 1, 2005

Sulfidisation Promotion Effect of Ammonium Sulfate on the Flotation of Copper Oxide Ores

Sep 13, 2010

By John C. MacCartney

In the Pennsylvania anthracite region, the principal source of U.S. anthracite, refuse disposal problems are common since cities and towns are located over the anthracite measures. The Bureau of Mines surveyed refuse banks in the area, determining that 863 banks containing aver 910 million cubic yards of material occupy a total area of about 19 square miles. The vast bulk of the refuse is located within 2 miles of the traffic centers of incorporated c unities which have a total population of 625,000. Twenty-seven banks are burning, causing considerable distress in a number of communities.

Jan 1, 1969

COALTECH 2020 initiated a research project to provide the coal mining industry with a modelling tool to determine the expected types of subsidence, risks and the investment required in post-closure funds to cater for subsidence associated with bord and pillar mines. A detailed literature review was conducted to determine the most important parameters in calculating the cost associated with surface subsidence. A subsidence prediction model was developed to determine the likelihood of different types of subsidence. The study made use of current knowledge of failure mechanisms and its aim is to assist the industry and government in arriving at the most suitable arrangements when authorities require financial instruments to assure compliance with environmental regulations.

Jan 1, 2003

By P. A. Plunkert, D. E. Morse, L. McCartan, J. F. Papp

The mineral sector is a fundamental part of the U.S. economy. It contributes to the real gross domestic product (GDP) at several stages —basic (mining), intermediate processing, manufacturing of finished goods and construction. The real GDP increased by 3.5 percent from 2004 to 2005. The nominal GDP was $12.5 trillion at the end of 2005. Housing starts were up by more than 5 percent for the year, and the unemployment rate decreased to 5.1 percent in 2005 from 5.5 percent in 2004. The prime interest rate increased from 5.25 percent at the beginning of the year to 7.25 percent at the end of the year. The value of minerals mined in the United States in 2005 rose significantly because of increased unit prices for some metals —particularly molybdenum — and significantly increased production for some industrial minerals, mainly cement, construction sand and gravel, and crushed stone.

Jan 1, 2006

By Peter B. Dowden, Robert A. Robinson

Boulders, frequently found in tunnels excavated through soils, can pose major problems for full face TBMs in terms of slowing or halting the tunnel advance, cutter damage, and abrasive wear. The paper aims to consider the problem as a whole, from the geological characteristics of boulder sites, to the appropriate physical design of theTBM, and its operation in boulder-laden soils. In addition, visualization of boulders and other subsurface obstructions by seismic methods and ground penetrating radar are reviewed. The paper will assist the construction planner in assessing the risks and preparing appropriate specifications.

Jan 1, 2001

By A. Dave Mackintosh

In 2001, at the CIM AGM in Quebec, a paper discussing poor ground conditions in a newly opened area at Agrium?s Vanscoy Potash Operation?s, suggested load transfer around old workings as a possible reason for the early room failure. High closure rates are expected in deeper regions however the rapid failure of walls immediately behind the face resulted in protective guards being mounted on and behind the borer. The high closure and early rib failure continued well past any reasonable distance to be explained by load transfer around old workings and investigations continued into possible reasons other than simply depth. Detailed investigations into the mineralogy and crystal fabric of the ore zone provided one possibility, which combined with a changed borer cutting profile are now believed to have contributed greatly to the poor conditions.

Apr 1, 2005

By P. A. Rey

Water recycle is an important part of the coal preparation process. This study was directed toward: (1) a survey of current practice and an evaluation of both the solid and liquid components of blackwater, (2) an experimental study of blackwater flocculation, and (3) a fundamental analysis of the flocculation process. The solids contained in the blackwater discharge to the fine refuse thickener of a coal preparation plant were found to contain, on average, 56% coal and 44% mineral matter. The mineral matter was largely illitic clay, while the water phase contained relatively large amounts of S04 and Ca++. Detailed studies were made of both natural and synthetic flocculants and the influence of polymer type and pH on the settling rate, turbidity of the supernatent liquid and sludge volume of the settled solids. More tundamental studies were made that clearly indicate the need for controlled mixing of polymer into the suspension to be flocculated, and the need to evaluate, more closely, the structure of the flocs formed during the process. Research recommendations are given.

Jan 1, 1983

By S. J. Schatzel

In order to better understand the effects of longwall mining on the methane reservoir overlying the panel, the National Institute for Occupational Safety and Health/Pittsburgh Research Laboratory (NIOSH/PRL) designed and implemented a vertical borehole monitoring experiment (BME) on an active longwall panel. The mine operates in the Pittsburgh Coalbed in Greene County, Pennsylvania. The BME site was located away from either end of the panel to avoid mechanical influences caused by the draping of overburden in this region and was positioned at the same distance from the tailgate gateroad as the mine?s gob gas venthole sites. The borehole drilling depths and monitoring intervals were chosen to address a different stratigraphic zone in each of the three planned holes. The monitoring boreholes were positioned perpendicular to face advance using a close spacing pattern of about 15 m (50 ft) between collars. Boreholes were instrumented downhole and on the surface for various measurements. It was observed from the field data that the gob gas venthole fracture network formed 24-46 m (80-150 ft) ahead of the mining face. Overburden permeability?s within the same test zones increased 100 to 500 times following undermining. The borehole test interval within the fractured rock responded to overburden gas pressure while the test interval in the caved zone responded to mine ventilation conditions. Eight months after the boreholes were undermined, slug testing indicated permeabilities had increased further in the fractured rock zone. Measurements of surface movement indicate that the permeability development observed in the boreholes is a product of vertical subsidence without lateral movement within the tensional rock mechanics zone on a supercritical longwall panel. Results from this study suggest that maximum permeability in the longwall panel overburden is achieved 58 to 190 m (190 to 620 ft) behind the longwall following maximum compaction of the overburden.

Jan 1, 2009

By K. Woodward

"SynopsisSeismically active mines generally experience an increase in seismic hazard due to rock mass instability following blasting. Re-entry protocols commonly include measures to limit the spatial and temporal exposure of personnel to increased seismic hazard induced by blasting. The management of periods of increased seismic hazard requires the development of re-entry protocols for a unique mining environment. Identifying mining conditions that may result in significant seismicity following blasting relies on retrospective analysis, which is often focused on seismicity occurring within a certain period after blasting and within a certain radius of the blast in the broader context of site-specific experience.The analysis of seismicity without considering blasting times and locations allows for the relationship between seismicity and blasting to be investigated without prior assumptions concerning dependency. To achieve independent analysis, seismicity that is clustered in space and time (referred to as a seismic sequence) must be identified by assessment utilizing only seismic parameters. An automated algorithm is implemented that assesses the timing, location, and quantity of seismicity to identify seismic sequences, represented by the time of the first event and mean location of all events in the sequence.The relationship between sequences and blasts is assessed by calculating the distance and time from each sequence to the closest blast in space and time. Establishing an independent classification between sequences and blasting provides insight into the unique cases where seismic sequences are remote and/or delayed with respect to blasts and identifies cases when sequences exhibit a weak relation to blasting. The nature of seismic responses to blasting has direct implications for the management of the increased seismic hazard associated with seismic sequences.The approach presented in this study contributes to the management of seismic hazard by providing empirical support for the relationship between seismic sequences and blasting. These relationships indicate the portions of sequences that can and cannot be practically managed using tactical approaches. Furthermore, the analysis of sequences reveals the nature and evolution of rock mass responses to blasting. These results have implications for the extent of spatial or temporal re-entry restrictions required for the optimal management of time-dependent rock mass response to mining."

Jan 1, 2015