Search Documents

By H Aral

A rotating magnetic field can be produced in a magnetic separator by using a magnet rotor fitted with alternate north-south magnetic poles, similar to the rotors currently used in modern eddy current separators. Rotation of the magnetic field causes ferromagnetic particles to rotate during magnetic separation. The particle rotation can then be used simply to remove entrapment during a conventional attraction magnetic separation (RMF lift separation), or it can be used to roll particles away from non-rotating particles, and to move them out of the separator under their own rotation (RMF rotation separation). RMF (rotating magnetic field) separation is a separation for ferromagnetic particles. These particles have a very ordered magnetism that is locked into directions of easy magnetisation in the crystal. As a result, if the external field rotates, the particles attempt to rotate with it. RMF separation uses this fact to rotate the ferromagnetic particles in a rotating field. In contrast, paramagnetic particles have a magnetism that can point in any direction with almost equal ease, and these will not rotate in a rotating field. By making use of this difference in magnetic properties, RMF rotation separation can separate ferromagnetic particles from paramagnetic, even when the particles have similar susceptibilities. Some particles such as both chrome spinel and ilmenite can contain ferromagnetic regions within a paramagnetic matrix. These ferromagnetic regions can vary from very small regions dispersed throughout the crystal, through thin lamellae, to larger more bulky regions. Although most natural ilmenite is ferromagnetic and generally has a higher magnetic susceptibility than paramagnetic chrome spinel, the susceptibility ranges for the two minerals overlap considerably (Allen, 2000a) due to the presence of these ferromagnetic elements, frequently making the conventional magnetic separation of these two minerals impractical. It is known that roasting a mixture of ilmenite and chrome spinel particles increases the magnetic susceptibility of the ilmenite while leaving the spinel susceptibility substantially unchanged. This makes the use of conventional (susceptibility attraction) magnetic separation more practical for the separation of these two minerals. However, very little is known about the effects of roasting on the response of ilmenite and spinel particles to a rotating magnetic field. For example, although the optimal ilmenite roasting conditions for conventional magnetic separation are quite well established such conditions may or may not be optimal for RMF rotation separation. Low intensity conventional magnetic separation on the basis of magnetic susceptibility can be made more accurate if it is carried out in a rotating field, because the rapid spinning of the separating particles prevents the formation of magnetic flocs, and reduces entrapment and entrainment. Medium intensity RMF rotation-only separation (no attraction component) has the ability to separate rotating (ferromagnetic) from non-rotating (paramagnetic) particles, irrespective of their relative magnetic susceptibilities. RMF rotation separation is of particular interest in this case because ilmenite particles generally rotate much better than the mainly paramagnetic chrome spinel particles, and roasting could enhance this difference further. Further information on the use of RMF to separate minerals can be found in Allen (2000a; b and c). The aim of this series of tests on a number of Australian ilmenites was to compare some different oxidising and reducing roast methods and to establish whether the use of RMF rotation separation improves the chrome spinel rejection.

Jan 1, 2001

By P. Mbele

Iron ore concentrate is not easily transported to, or processed in, ironmaking plants, therefore it is necessary to agglomerate. This paper will determine the possibility of agglomerating Sishen concentrate into suitable ironmaking feedstock. Pelletizing is one of the conventional and preferred agglomeration processes for iron ore concentrate investigated at Kumba Value-In-Use Laboratories. Sishen concentrate was mixed with binder, and then pelletized using a laboratory pelletizing disc; afterwards the green pellets were indurated at high temperatures to give strength high enough to survive handling and lessen disintegration in the shaft during ironmaking. Sishen pellets have satisfactory physical and metallurgical properties which make them suitable feedstock for the direct reduction processes. These were tested under Midrex shaft operational conditions and performed well, with a metallization of 94.47% being attained.

Jan 1, 2012

By X. Bai

A new heuristic sublevel mining stope optimizer is presented. The optimizer seeks the best locations and lengths of a series of vertical raises that, together with the blocks linked to each raise, define a mining stope. Five design constraints ? the footwall angle, the hangingwall angle, the number of raises, the maximum distance of a block from a raise, and the minimum width required to move the farthest block towards the raise ? allow the shape of the sub-stopes associated with each raise to be controlled. The optimization is done on the locations and lengths of raises using a genetic algorithm to efficiently sample the parameters? space. For each raise, a local network is defined in cylindrical coordinates around the raise such as to impose the design constraints. A maxflow algorithm on the local network is used to determine the optimal sub-stope for each raise. All substopes are combined to define the global stope for the entire deposit. The best global stope is obtained using a genetic algorithm to find the raise parameters providing the best profit over the entire deposit. Two synthetic cases and one real deposit are used to evaluate the new algorithm and compare the results with the single-raise optimizer. The multiple raises approach leads to significantly improved economics compared with the single-raise stope optimizer, and the dilution is also substantially reduced compared to the single-raise case.

Jan 1, 2014

The Round Hill gold-scheelite deposit is located three kilometres from Macraes Flat and approximately 60 kilometres due north of Dunedin, New Zealand. A mining feasibility study is currently being undertaken on the deposit by BHP Minerals (New Zealand) Limited, who are the managers and operators of a Joint Venture with Home Reef Mining Limited. BHP has a 70 per cent equity in the project area.

Jan 1, 1987

By Robert B. Bittner

"AbstractLarge diameter tubular piles offer significant advantages in terms of design performance and economy for major marine structures. This is particularly true for foundations of major overwater bridges in regions of high seismicity such as the west coast of North America. The use of large diameter piles in the range of 2 to 3 m diameter means that fewer piles are required, and the size and mass of the pile caps can be significantly reduced, thereby greatly reducing lateral load demand during seismic events. Another advantage of using larger diameter piles is increased pile stiffness that allows the pile caps to be located at or near the waterline rather than being positioned at or below the mud line. This elevating of the pile cap offers significant cost savings by eliminating the need for deep cofferdams. However, relocation of the pile cap creates new problems and opportunities in regard to the means and methods used to construct the pile cap. With the pile cap at depth, conventional steel sheet pile cofferdams with thick tremie seals are typically used to isolated the cap location and allow dewatering for construction of the cap. However with pile caps positioned up off the bottom, conventional bottom founded cofferdams are no longer cost efficient. Float-in or lift-in cofferdams have been developed to address the need for a more cost efficient method for cap construction. This paper describes the key features of the concept and provides three case history examples of its successful implementation.Pier Construction Using Conventional Sheet-Pile CofferdamsCofferdams are temporary structures used in the construction of bridge piers and other marine structures. Their primary purpose is to hold out water and unstable soil from the construction area, and thereby, allow in-the-dry construction of the permanent structure below the water line and quite often below the mud line. Typically, cofferdams consist of long interlocking steel sheet piles driven through water into the bottom of the waterway. The sheet piles form temporary exterior walls which are typically braced internally with wales and struts. The bottom of the cofferdam is typically sealed with tremie concrete or an impervious clay layer if one exists. The depth at which this type of cofferdam can be used is typically limited by the length of steel sheet pile that can be transported and handled by conventional marine equipment."

Jan 1, 2014

By J. D. T. Steyl, C. A. Biley

"The chemistry of electrolyte systems containing iron remains generally poorly understood despite their prevalence in many natural and industrial processes, particularly in hydrometallurgy. These systems are typically challenging to study and model due to their affinity for complex formation and precipitation even at low pH. Recent developments in the hydrometallurgical processing of nickel laterites at Anglo American have called for a deeper understanding of the fundamental chemistry of the Fe2(SO4)3–FeSO4–H2SO4–H2O system. This paper details the development of an internally consistent, Pitzer ion-interaction model of this system, with explicit recognition of important contact ion pairs (CIPs). The primary application of this model is a thermodynamic framework for the interpretation of kinetic processes occurring during iron(III) reduction with SO2. Adopting a rigorous thermodynamic basis for the system chemistry facilitates the formulation of simple rate expressions that are capable of inherently capturing complex effects. While the iron(III) reduction case study remains the focus of this work, the developments have more universal applications and the thermodynamic speciation model can be extended into other systems containing acidic ferric sulfate.INTRODUCTIONIron is present in nearly all hydrometallurgical refining circuits typically as both a necessary and unwanted impurity and needs to be removed and disposed in a safe and efficient manner. This is generally performed by precipitation to form a range of solids such as hematite, goethite or jarosite. Numerous studies in the open literature have focussed on the removal of iron from refractory gold sulfide ore (Berezowsky & Weir, 1989; Berezowsky et al., 1991) and zinc pressure leaching (Buban, 1999; Ismael, 2003), and PGM matte sulfide circuits (Dutrizac & Monhemius, 1986). Moreover, since ferric iron is a strong oxidizing agent, it has been used extensively as a leaching agent for sulfide minerals (Dreisinger, 2006). Given the outlook of challenging economic conditions, declining ore grades and increasing levels of impurities, effective iron management is going to become increasingly critical to all hydrometallurgical processes.Against this background, and considering the widespread importance of acidic iron sulfate systems throughout natural and industrial processes, it is unexpected that the knowledge of the fundamental solution chemistry of these systems contains such significant gaps, particularly at the conditions typically found in hydrometallurgical applications. Existing literature describing the measurement and modelling of solution speciation in these systems have highlighted their significant chemical complexity (Magini & Caminiti, 1977; Magini, 1979; Lee & Tavlarides, 1985; Stipp, 1990; Papangelakis et al., 1994; Gil et al., 1995; Majzlan & Myneni, 2005; Kormanyos et al., 2008; Yue et al., 2014). Partially responsible for the lack of quantitative speciation measurements is the strong tendency of ferric to hydrolyse at even low pH (Flynn, 1984), complicating the laboratory study of such systems. Moreover, the large number of aqueous species that may co-exist simultaneously makes the study of individual species and the modelling of the numerous interactions between these species extremely difficult (Dry & Bryson, 1988; Stipp, 1990; Majzlan & Myeni, 2005; Kobylin et al., 2007)."

Jan 1, 2016

Future metal prices play a direct role in both the economic evaluation and short to medium planning of a mine scheduling sequence. It is difficult to predict with accuracy the future price of volatile metal commodities, however, it is possible to fix some future metal price, outside of long term contracts by the selling of futures contracts through a commodities exchange. The futures contract represents a fixed amount of a specified quality of a commodity for future delivery at a predetermined price. Several different types of hedging are possible, one in particular which is best suited for mining companies. There are relative advantages and disadvantages when trading in futures contracts and particular reference is made to gold contracts on the Sydney Futures Exchange.

Jan 1, 1980

By Floyd G. Anderson

This report reviews and summarizes information on prevention and suppression of dust in mining, tunneling, and quarrying published in the United States from 1961 through 1967. Unpublished pertinent data developed or assembled by the Bureau of Mines during this period also are included.

Jan 1, 1969

By Steve Chorley

Open-type, or main beam, tunnel boring machines (TBMs) can achieve impressive rates of production. This type of TBM typically outperforms other types of TBMs currently in use around the world. In good ground conditions, main beam machines have achieved production rates of more than 1 km/month (0.6 miles/month). However, installing effective ground support in poorer rock conditions on main beam machines can be a major cause of concern. The design of main beam machines is such that installation of ground support equipment, particularly at the front of the machine in what is commonly known as the L1 support zone, has traditionally been limited to rock drills and basic working platforms. Personnel working in the L1 zone have, until recently, been protected by roof supports and extended fingers, often with restricted access to working areas.

Jan 1, 2011

By Alonso Marchena, William Martínez

El estudio que se ve reflejado en el presente artículo tuvo como objetivo mantener actualizado el mapa metalogenético del Perú y desarrollar conceptos sobre el origen de los yacimientos minerales, basados en datos geocronométricos, geoquímicos, isotópicos, estratigráficos y estructurales, en la Cordillera Occidental entre Ica y Tacna. La zona de investigación comprende las franjas metalogenéticas IV, V, VIII, IX y X. Se destaca el valor de herramientas tales como la litogeoquímica en la discriminación de pórfidos de Cu (Mo-Au) y se muestra la efectividad de nuevos parámetros de elementos traza en la discriminación y reconocimiento de magmatismo fértil vinculado a pórfidos en el sur del Perú.

Oct 30, 2020

By Maurice Bottiau

It is a quite challenging objective to aim at covering in one paper the most recent evolution in piling and deep foundations technologies. This report has to be understood within the limits of the session 2b. It will therefore concentrate on the technological evolution of deep foundation techniques, addressing design issues only when directly related to execution aspects. For the same reason, it will not address the related codes, as a separate session of this conference is specifically dedicated to this topic. Monitoring and deep excavations being covered in other sessions, they will only be addressed when clearly relevant. We will try to show, from a practical viewpoint what are the main changes and the most exciting or critical issues over the last years, as they appear from the topics addressed in the literature or in the papers published in this session of the conference. As the paper mostly intends to explain trends and critical topics, it cannot be exhaustive, neither can it give the full description of the case studies. The author invites the reader to read the full papers, for a more complete description. We have divided our report in three main topics: Piling, soil improvement and treatment and retaining walls. Anchors and tie-backs will not be treated, neither tunneling.

Jan 1, 2006

By Karsten Beckhaus

"Abstract Tremie concrete for special geotechnical works needs special properties, especially during the casting process. Today’s execution standards for bored piles and diaphragm walls, EN 1536 and EN 1538, as well as the draft version of concrete standard EN 206, all comprise regulations for deep foundation concrete which have not been changed for decades. Considering the recent development in concrete technology at the same time and its actual state-of-the-art, it is essential to develop new normative specifications and specification requirements.GeneralTo allow the required integrity and quality after placing and hardening, concrete for structural elements like bored piles or diaphragm walls, used as foundations of high-rise buildings or as retaining structures for large and deep building pits, must have adequate workability and stability.In addition to requirements on mechanical properties and on durability, both of which have increased within the last decades, concrete must be suitable for being cast in deep or extremely deep excavations, see figure 1. Today’s specialist foundation engineering machinery makes it possible to drill or cut down to in excess of100 m depth. Concrete technology has developed and allows the use of high performance concrete for deep foundations. But is this capability represented by actual regulations?It has become very common for the industry to supply or use concrete with low water cement ratios, nevertheless highly flowable and set-retarded for several hours if needed. Very low water cement ratios allow design strength of 60 MPa or higher (Larisch, 2011), and a very low porosity which is required for a long service life in aggressive conditions, e.g. by chlorides.To achieve best performance, it is obvious that the concrete must completely fill the excavation and fully embed the reinforcement. As vibration of deep foundation concrete is (usually) not allowed and was anyway inefficient, deep foundation concrete must be designed to self-compact under hydrostatic pressure. Generally, it must be considered that after placement the concrete’s quality cannot be influenced anymore. Therefore, both the pouring procedure and the concrete quality must be adequate."

Jan 1, 2014

By Benkendorff P. N

Cement production in Australia approximates 6.5 million tonnes per year. Cement clinker is sourced from 15 plants which operate 28 kilns. Cement grinding is conducted at 14 of the clinker plants plus 7 grinding plants. Average annual capacity per kiln or plant is lower than in many overseas countries, but kilns introduced since 1970's have been of larger size more in keeping with size trends overseas, although still smaller than the large units overseas. Substantial economies in capital and labour costs can be achieved in large production units, particularly with dry process kilns using precalcination techniques in which part of the fuel is introduced in the static preheater section ahead of the kiln while the balance is added to the kiln in a conventional manner. Precalcination techniques have been introduced to the Australian cement industry but as cement transport costs form a major part of supplying diverse market areas, the size of kilns is likely to remain less than maximum owing to balance with distribution costs. The cement industry uses significant amounts of thermal and electrical energy which can be minimised by proper selection of equipment and technology. Labour costs are also significant and can be contained by automation and computer control of the process.

Jan 1, 1989

By Tae-kyeong Yeu, Jong-Choi, Cheon-Hong Min, Hyung-woo Kim, Jae- Won Oh, Sup Hong, Minuk Lee, Sung-Soon Kim, Chang-Ho Lee, Ki-Young Seong

"Collecting mineral resources from the seabed using a seafloor crawling robot is the firststep in the mining operation. The second-step is lifting the collected ore up to the water surface. For lifting through a riser pipe, prevention of pipe clogging (flow assurance) and economic and eco-friendly up-transferring is of the utmost concern.During collection of mineral ores, the production rate can be highly variable because of the variability in the distribution of the mineral deposit, variations in seafloor topography, fluctuations robot speed, and variations in performance of the mining robot, etc. Direct transfer of the collected ore to the riser pipe might cause unpredictable and serious problems such as over-loading of the lift pump, reduction in the life of the equipment, pipe clogging, severe increase of down-time, critical damage of equipment, further propagation of damages, and total failure after all.As a counter measure to these potential problems, a buffer station has been adopted, which is capable of storing the collected ore for a certain time and simultaneously regulating the transfer of the ore into the riser pipe. A pilot buffer has been developed by KRISO/KIOST (see Fig. 1)."

Sep 1, 2014

By K. C. Garner

The visit reported was made with support from the 1997 J.C. Boyle travelling scholarship. The management and control of hazardous gases released into the underground environment are an integral part of coal mining. The power-generations stations at Appin and Tower collieries, with a combined electrical output of 94 MW, have been operating for some time and have demonstrated a technology that is able to exploit the available gas fully. Contributory factors have been the development and introduction of directional drilling techniques, pre- and post-drainage of coal, relatively high seam permeability, a high gas content of the worked seam, high production rates and a willingness to embrace new ideas and technology

Jun 21, 1905

Longwall mining has existed in Utah for more than half a century. Much of this mining occurred at depths of cover that significantly exceed those encountered by most other U.S. longwall operations. Deep cover causes high ground stress, which can combine with geology to create a coal burst hazard. Nearly every longwall mine operating within the Utah’s Book Cliffs coalfield has been affected by coal bursts.

Jan 7, 2020

The Electricity Generating Authority of Thailand (EGAT) Mae Moh coal mine is an open-cut coal mine in Thailand that produces about 16 Mt of lignite annually to generate 2400 MW of electricity. The surface mine pit covers is 4 km by 7 km with mining depths ranging up to 260 m. A large pit slope is formed with the progression of the mining operation. However, massive slides in the pit slope occur often due to the existence weak planes such as faults and bedding, and the weak mechanical properties of the rocks. Hence, 200 m to 300 m boundaries of rock block including coal seams are left in front of faults in order to prevent slides and maintain the stability of the pit slope. As a result, there are significant coal reserves beneath the abandoned area along the pit slope. Moreover, the mined coal seams are very thick and their thickness range from 15 to 30 m.This paper discusses the application of multi-slicing highwall mining system with stowing to this very thick coal seam left around large pit slopes by means of numerical analysis.

Dec 6, 2010

By Paloma Lazaro, Moe Momayez

Heat-related illnesses (HRI) are relatively common in both hot surface and underground mining operations. When workers are exposed to extreme heat or strenuous work in a hot environment, they become prone to heat stress. Heat strain is the result of the body’s response to external and internal heat stress. It is therefore vital for the conditions leading to heat strain be detected and treated in a timely manner. Heat-related illnesses are manifested by exhaustion and heat stroke. The predicted heat strain (PHS) [ISO 7933 (2004)] model has been developed to predict the health condition of the worker in terms of core body temperature and water loss. The PHS model tested in this study is based on eight physical parameters that are measured at different intervals during a work shift. They include air temperature, humidity, radiation, air velocity, metabolic rate, clothing insulation, posture, and acclimatization. The model predictions are then compared with a direct physiological measurement, such as core body temperature. We present the results of an extensive study that monitored and predicted body’s response to heat stress under different environmental and working conditions. The PHS model provided reliable results in most instances in comparison with other prediction methods currently in use in the field.

By Paloma Lazaro, Moe Momayez

Heat-related illnesses (HRI) are relatively common in both hot surface and underground mining operations. When workers are exposed to extreme heat or strenuous work in a hot environment, they become prone to heat stress. Heat strain is the result of the body’s response to external and internal heat stress. It is therefore vital for the conditions leading to heat strain be detected and treated in a timely manner. Heat-related illnesses are manifested by exhaustion and heat stroke. The predicted heat strain (PHS) [ISO 7933 (2004)] model has been developed to predict the health condition of the worker in terms of core body temperature and water loss. The PHS model tested in this study is based on eight physical parameters that are measured at different intervals during a work shift. They include air temperature, humidity, radiation, air velocity, metabolic rate, clothing insulation, posture, and acclimatization. The model predictions are then compared with a direct physiological measurement, such as core body temperature. We present the results of an extensive study that monitored and predicted body’s response to heat stress under different environmental and working conditions. The PHS model provided reliable results in most instances in comparison with other prediction methods currently in use in the field.

By Rob Farnfield, William Birch, Douglas A. Anderson

In the blasting industry, even to the most safety conscious shotfirer, misfires are a constant source of concern. In the United Kingdom, there are two types of misfire, as classified by the Health & Safety Executive. Type A occurs when testing a shot before firing reveals broken continuity that cannot be rectified. However, due to the fact that a majority of quarries use non-electric initiation [i.e. shock tube] that cannot be tested, this type of misfire is very unusual.

Jan 1, 2016