Search Documents

By J. F. T. Agapito, G. P. Bratton

A 16 m by 4.7 m by 24.5 m (52 ft by 15.5 ft by 80.5 ft) underground ore bin was constructed at an 810 m (2660 ft) overburden depth in poor quality, faulted and altered intrusive rocks at Molycorp's block caving molybdenum mine. Geological engineering incorporated detailed structural mapping, rock quality classification, in-situ stress field determinations, numerical stress and failure analysis, and convergence monitoring. The ore bin was mined by conventional methods from the top down and utilized a bored raise for mucking. The initial ground support of rock bolts, lightweight steel sets, and reinforced concrete was later supplemented with an array of 6, 12 and 21 m tensioned, grouted rock bolts when wall closure was noted in the upper ore bin area. The supplementary support was optimized by computer analysis and monitoring.

Jan 1, 1985

By S. Ngidi

Palabora Mining Company operates a low grade underground copper mine situated in the Limpopo Province, South Africa. Full production was first reached in May 2005 after a successful transition from an open pit operation to an underground block cave operation. The operation faces a number of technical and operational challenges, not the least being fragmentation of a competent rock mass and external dilution. The cave is subdivided into three main sectors being the east, the west and the central sectors. Caving was initiated from the weaker central sector, which has the majority of its drawpoints located directly under the open pit bottom currently filled with about 130 million tons of waste material from the pit wall failure incurred in 2004. About 48% of the ore reserve has to be extracted from the western sector, which has a much courser fragmentation compared to the other two sectors and only 25% from the central sector with the finest fragmentation. The main constraint during the ramp-up stage has been secondary breaking of drawpoint blockages. Ground-breaking secondary breaking and cave management initiatives and practices have made it possible for Palabora to realize and sustain high production rates.

Jan 1, 2007

By T. V. Nguyen

The feedwell performance in gravity thickeners and clarifiers relies on the efficient mixing between solid particles and flocculant to achieve effective flocculation, as well as energy dissipation of the incoming feed stream. A population balance-computational fluid dynamics (PB-CFD) model has been developed and validated to provide new insights into the operation and performance of industrial feedwells. In particular, the PB-CFD model enables the efficacy of the main functions of a feedwell to be investigated for a wide range of feedwell designs and process conditions. This paper describes how PB-CFD was used in the design and development of a new feedwell concept for the flocculation of particles in a solid-liquid stream. The patented feedwell design includes an upwardly converging flow diverter to create two separate compartments for energy dissipation and flocculation. PB-CFD simulations of this simple and easy-to-retrofit feedwell design illustrate a superior performance in terms of flocculation and energy dissipation compared to typical feedwells over a wide range of flow conditions. The potential benefits include reduced flocculant consumption, better de-aeration, greater stability and the ability to cope with a wider variation in volumetric throughput, better flocculation and fines capture, and a more symmetrical discharge that may also offer improved overflow clarity in some applications. The new feedwell design has been installed in a full-scale thickener at an Anglo American Platinum site in South Africa. A number of operational factors complicate this application, but indications are that the new feedwell has led to improvements in stability and underflow properties.

Jan 1, 2012

By J. F. Wilson

An experimental investigation has been made of gas-driven slug displacements in a system of high gas saturation to evaluate the process for use in a California reservoir. Fluid compositions, temperature, pressure and core permeability duplicated reservoir conditions as closely as possible. The temperature was above the critical of the slug materials. The slug composition required for 100 per cent oil recovery in the linear flow systems was found to agree with that determined from equilibrium phase studies. A qualitative theory for the slug displacement of two-phase systems is proposed and found to be in general agreement with the observed flow behavior. The theory predicts that the length of the reservoir fluid-slug transition Zone will increase with increased initial gas saturation and decrease with increased oil swelling accompanying the composition change from reservoir oil to the critical composition. The precipitation of small amounts of an asphaltic phase during the formation of the transition zone had no adverse effects on the flow behavior of otherwise miscible systems. INTRODUCTION Despite the large number of recent publications relating to oil recovery by miscible displacement, little information is available concerning the behavior of crude oil-natural gas systems at conditions likely to be encountered in field application. The laboratory data reported here were obtained during an investigation of the possibility of using a gas-driven LPG slug in a partially depleted California reservoir. Seven gas-driven slug displacements employing slugs of different compositions and sizes were made in 26- to 27-ft long sandstone cores. The equilibrium phase behavior of the systems was also determined. The features of primary interest in this study are the following. 1. Data were obtained on the displacement of reservoir fluids at reservoir conditions. 2. A high gas saturation existed in the long cores at the start of the displacements. 3. The temperature of the studies was above the critical of the slug materials. 4. A comparison between the flow behavior and equilibrium phase behavior, as illustrated by a pseudo-ternary phase diagram, is afforded for a system of considerable complexity. THEORY Phase Behavior The use of the pseudo-ternary phase diagram to illustrate the phase behavior in miscible displacements has been discussed by Clark, Schultz and Shearin. Sie-vert, Dew and Conley and Arnold, Stone and Luffel' have presented both phase equilibrium and flow data for true ternary systems. For the true ternary, the application of the theory is straight-forward; for a reservoir system represented as a ternary, the theory undoubtedly gives a qualitatively correct picture. One purpose of this investigation was to see if the pseudo-ternary phase diagram could be used to predict with reasonable accuracy the conditions necessary for miscible displacements with actual reservoir systems. MiscIBLE Displacement of Two-Phase System A large number of papers "I3 have treated the miscible displacement of a single-phase fluid from both an experimental and a theoretical viewpoint. However, the normal field application of the process will be in a partially depleted reservoir. Often the state of the system will be such that the mobility of the gas phase is greater

Despite the current economic downturn that is now decimating iron ore production, Minnesota?s mining operators remain optimistic about the long-term prospects for the industry. Reflecting this optimism, the development of several new mining projects continues in the state. The future of mining in Minnesota was the featured topic at the combined 82nd Annual Minnesota Section of SME Meeting and 70th Annual University of Minnesota Mining Symposium. More than 500 mining industry professionals, including engineers, executives, mining managers and equipment suppliers from the around the world, attended the meeting, which was held April 14 and 15, 2009, in Duluth, MN. The combined meeting featured a keynote session with three distinguished speakers plus a panel discussion by representatives from several of Minnesota?s taconite producers. The keynote speakers were Curtis Clark, president and chief operating officer, Behr Dolbear, who gave a presentation on the ?State of the Mining Industry.? Phil Newman, chief operating officer, CRU Strategies, spoke about challenges facing the mining industry and James A. Skurla, acting director, Bureau of Business and Economic Research, Labovitz School of Business and Economics, University of Minnesota Duluth, discussed the importance of mining to northeastern Minnesota?s economy. The taconite producers panel discussion included Jonathan Holmes, vice president and operations manager, ArcelorMittal; Ed Latendresse, vice president and general manger, Hibbing Taconite; John Tuomi, vice president operations services, United Taconite and Mike Mliner, vice president and general manager, Northshore Mining. The mangers provided updates on their respective operation The meeting included concurrent technical papers sessions on mining, processing, environmental and nonferrous mining. The sessions included technical papers that provided information on the status of a number of new mining projects in the state. The conference also offered a SME short course titled ?The basics of iron mining.? A tradeshow that featured about 100 companies and organizations offering products and services to Minnesota?s mining industry ran in conjunction to the conference. It was estimated that more than 900 people, including conference registrants and special invited guests of the vendors, attended the tradeshow opening reception. This was the largest trade show in many years. The Minnesota Section of SME also held its annual business meeting during the conference.

Jan 1, 2009

By M. Foguenne, A. van Lierde, P. Henry

Leaching experiments were carried out on a spent catalyst sample with a honeycomb structure, containing 47.5% Ti, 5.8% Mo, 2.7% Si, 2 035 ppm As, 52 ppm Pb and 8.8 ppm Hg. More than 93% of the Mo and As was removed by direct alkaline leaching after grinding to 80% -36 micrometres. The residue contained 0.3% Mo and 60 ppm As. To obtain a TiO2 matrix with 30 ppm As, acid leaching at controlled pH with 90 kg/t Al scrap was followed by oxidising alkaline leaching. Treatment of the direct alkaline leach solution or of the mixed solutions from the two-stage process involved two successive operations: purification by neutralisation with Al(OH)3 addition to raise the Al concentration to 4 g/l, and ion exchange on Amberlite IRA 94 S resin. Whatever the type of solution treated, elution with 200 g/l NH4OH solution gave an eluate of very high purity containing 164 g/l Mo, less than 70 mg/l V and less than 2 mg/l As

Jun 19, 1905

By K. Coleman, C. Visser, N. Selby, X. W. Pan, T. Letwaba

A prototype weightometer soft sensor is under development at DebTech, De Beers in partnership with Venetia Mine. Its main function consists of an online data source; data validation; dynamic weightometer models; online detection of weightometer failure; alarming and replacing a weightometer when it fails. 31 dynamic models have been developed. All models with R2>= 85%are accepted as good models and they generally have satisfactory results with a daily error of less than 8% within 90% confidence level. By using those models, a set of soft sensors can be set up to cover all weightometers in the entire processes starting from primary crushing to the stock piles of dense medium separation (DMS). Some practical issues and concerns on model development are discussed, including data collection, data analysis, data pre-processing, variable selection, time delay, model training and model validation. When deploying the weightometer soft sensor system, the potential benefits could include: reduction in plant downtime; reduction in unplanned maintenance and even replacement of non-critical weightometers, particularly where nuclear weightometers are used. Keywords: soft sensor, weightometer, dynamic modelling, neural network modelling

Jan 1, 2003

The uptake of nickel into the lattice of pyrrhotite, Fe1 _1J S was studied experimentally in the temperature range 200°C to 760°C. Nickel from both aqueous solutions and salt melts diffuses rapidly into the sulphidelattice with an accompanying release of iron into the solution or melt. The rate of uptake of nickel and its diffusion into the sulphide lattice were followed by optical microscopy and by analysis with an electron probe microanalyser. Some geological consequences of this phenomenon affecting the distribution of nickel in rocks associated with nickel-iron sulphide ores are discussed.

Jan 1, 1972

By L A. Maslov

We have considered the following characteristics of the crust and upper mantle of the Pacific Belt: seismic wave velocity anomalies, mechanical stress and shear deformation rate fields, heat flow and the pattern of metallogenic provinces of the Belt. It has been noted that there exist certain .regularities in distribution of the above mentioned geophysical characteristics and metallogenic zones within the Belt, displayed by prevalence of the lithophile elements in the Asia-Australian part of the Belt, and of the chalcophile ones within the American part.

Jan 1, 1995

In this paper a numerical formulation is presented for determination of the axial load along a cable bolt for a prescribed distribution of rock mass displacement. Results using the program CABLE indicate that during excavation, the load distribution that develops along an untensioned fully grouted cable bolt depends on three main factors: (i) the properties of the cable itself, (ii) the shear force that develops due to bond at the cable-grout interface (i.e. bond stiffness), and (iii) the distribution of rock mass displacement along the cable bolt length. In general, the effect of low modulus rock and mining induced stress decreases in reducing bond strength as determined from short embedment length tests, is reflected in the development of axial loads significantly less than the ultimate tensile capacity even for long cable bolts. However, the load distribution is also dependent on the deformation distribution in the reinforced rock mass. Higher cable bolt loads will be developed for a rock mass that behaves as a discontinuum with deformation concentrated on a few fractures, than for one which behaves as a continuum, either due to a total lack of fractures or a very high fracture density. This result suggests that the stiffness of a fully grouted cable bolt is not simply a characteristic of the bolt and grout used, but also of the deformation behavior of the ground. In other words, the same combination of bolt and grout will be stiffer if the rock behaves as a discontinuum than if it behaves as a continuum. This paper also explains the laboratory test programme used to determine the constitutive behavior of the Garford bulb and Nutcase cables bolts. Details of the test setup as well as the obtained results are summarized and discussed.

Jan 1, 1996

By T. A. Klinefelter

KYANITE and the related minerals sillimanite, andalusite, dumortierite, and topaz are natural aluminum silicates that can be used in production of mullite (3A1203?2Si02), a superduty refractory material. Kyanite and sillimanite are the dominant ones because of their greater abundance. The only other kyanite-group mineral presently used for mullite production is andalusite. Mullite is not an absolutely essential material as other refractories can be used in the same heat range. However, it is a highly satisfactory one. It is the only compound of silica and alumina that is stable at high temperatures. It has low thermal expansion and is very resistant to corrosive melts and to thermal shock. For these reasons mullite refractories have a much longer life than standard fire-clay refractories under the same conditions. Worldwide, excluding U.S.S.R., the refractories industry consumes about 150-000 short tons annually of kyanite group minerals and synthetic mullite.

Jan 1, 1961

By D. S. F. Silva

A survey of 120 recent NI 43-101 technical reports was conducted to evaluate the current state of practice regarding resource classification techniques. The most common classification techniques are based on search neighbourhoods (50% of recent reports), drill-hole spacing (30% of recent reports), and/or kriging variance (6% of recent reports). Two new techniques are proposed. The first is based on kriging variance and involves removing one or more drill-holes with the highest weights while performing kriging and using the resultant kriging variance for classification. This technique has the advantages of variance-based techniques and reduces artifacts. The second technique is based on conditional simulation and uses a moving window approach for classification at the desired selective mining unit resolution based on larger production volume criteria. This technique has the advantage of accounting for heteroscedasticity, which is a common characteristic in mineral deposits, and also reduces artifacts since a production volume scale is considered for the actual classification. The drill-hole spacing, search neighborhood, kriging variance, and simulation-based techniques are described and compared for 2D and 3D examples with regular and irregular drilling patterns to highlight the advantages and disadvantages of each method.

Jan 1, 2014

By Dean Nichols, Matt Ortel

Explosive accidents in the United States have brought increased attention to emergency operation plans (EOP) at all facilities that manufacture, transport, or store hazardous materials – particularly explosive materials. Explosions are sudden, powerful, and complex events that are difficult to characterize in terms of the thermal, over pressure, and debris effects. Industry, regulatory, and public officials require emergency response planners to not only anticipate the blast effects of an explosion, but also to prepare an appropriate response.

Jan 1, 2016

By M. J. McLeod, S. Watters, G. G. Lutes, S. Castonguay

"Gold-bearing mineralization at Anomaly A occurs in polydeformed Ordovician turbidites of the Kendall Mountain Formation of the St. Croix belt in southwestern New Brunswick, and is hosted by WSWtrending, shallow-dipping, brittle-ductile high-strain zones associated with the latest stage of the second of four regional deformation events. Gold-bearing syn-deformational stockwork, massive, and multiply brecciated quartz-sulfide veined zones form irregular pods and sheets up to several meters thick, which contain arsenopyrite, pyrrhotite, pyrite, stibnite, and a variety of rare minerals that are gold-bearing. Mineralized zones are enveloped by locally auriferous, weakly to intensely altered wall rock. Vein paragenesis includes: (1) early (pre- to syn-D2) quartz-chlorite veins that are largely the product of migration of quartz by pressure solution; (2) crosscutting, multiphase, vuggy quartz-sulfide veins that contain most of the gold and are interpreted to be structurally controlled; (3) late, crosscutting, nondeformed, non-gold-bearing veins containing laumontite, chlorite, muscovite, quartz, fluorite, and base metal sulfides. Carbonate-poor alteration associated with zones of gold mineralization is lithology-specific, and appears to reflect overprinting of multiple events. Major elements removed during alteration include Si, Na, Mn, and Mg. The minor and trace elements removed include Co, Li, Sc, and possibly Sr, Ni, and Zn. Minor and trace elements added include Au, Ag, As, Sb, S, and possibly F, Cu, Pb, and Zr. On the basis of proximity, time constraints, and a similar ore mineral assemblage, gold mineralization at Anomaly A is interpreted to be a distal equivalent of the intrusion-related gold mineralization at the nearby Clarence Stream Main zone deposit. La minéralisation aurifère de l’Anomalie A se trouve dans des turbidites Ordoviciennes polydéformées de la Formation de Kendall Mountain, dans la ceinture de Ste-Croix du sud-ouest du Nouveau Brunswick, où elle est contenue dans des zones de déformation fragile-ductile à faible pendage de direction OSO associées au dernier stade du second de quatre épisodes de déformation régionale. Les zones aurifères syn-déformationelles se présentent en forme massive, de stockwork, ou de veines de quartz-sulfure bréchifiées à répétition formant des lentilles irrégulières et des couches de plusieurs mètres d’épaisseur contenant de l’arsénopyrite, de la pyrrhotite, de la pyrite, de la stibine, ainsi que divers minéraux aurifères rares. Les zones minéralisées sont entourées d’une enveloppe de roches faiblement à intensément altérées, localement aurifères. La paragénèse des veines comprend : (1) des veines précoces de quartz-chlorite (pré- à syn-D2) qui sont principalement le produit de la migration du quartz par solution-pression; (2) des veines polyphasées de quartz drusique et de sulfures contenant la plus grande partie de l’or, celles-ci sont considérées comme étant sujettes à un contrôle structural; (3) des veines tardives stériles, sécantes et non déformées contenant de la laumontite, de la chlorite, de la muscovite, du quartz, de la fluorite et des sulfures de métaux usuels. Les zones de minéralisation aurifère sont associées à une faible altération en carbonate contrôlée par la lithologie et semble résulter de la superposition d’événements multiples. Les éléments majeurs perdus durant l’altération sont le Si, le Na, le Mn et le Mg. Les éléments mineurs et traces perdus durant l’altération sont le Co, le Li, le Sc et possiblement le Sr, le Ni et le Zn. Les éléments mineurs et traces enrichis comprennent l’Au, l’Ag, l’As, le Sb, le S et possiblement le F, le Cu, le Pb et le Zr. Étant donné sa proximité géographique, les contraintes temporelles et les similitudes de leurs assemblages minéraux, la minéralisation aurifère de l’Anomalie A est interprétée comme un équivalent distal de la minéralisation aurifère associée aux intrusions du gisement avoisinant de la zone principale (Main"

Jan 1, 2008

The AusIMM/AMIC code for reporting Reserves seeks to improve the calibre of professional reporting on this subject. But have they gone far enough? Should the code appreciate that the degree of reliability of estimates required will vary with the type of mining planned? How does one "confirm continuity" as required by the code? The aim of optimum development drilling is to achieve appropriate ore zone definition for acceptable estimates of reserves and their economic extraction. Can this procedure be in conflict with the code? How does it affect finance decisions?

Jan 1, 1989

By Alfredo C. Gurmendi

Perú, como parte de los países en desarrollo económico (PED, se caracteriza por las regulaciones en los sectores industriales y consorcios entre capitales extranjeros y nacionales. En este sentido, los cambios surgidos en este sector, deben buscar beneficiar a las generaciones futuras con los recursos naturales y encontrar balances entre la necesidad de una operación rentable y la de una adecuación ambiental, social, y descentralizada. Sin embargo, existe todavía una historia de centralismo de parte de los gobiernos centrales respecto al ámbito económico de las economías regionales y locales. Por ello, el presente trabajo describe la base para lograr una economía sostenible después de que la actividad del sector minero desaparezca a través de un entorno legal estable que incluya regímenes especiales e incentivos y administre los recursos naturales eficientemente, de forma que los protege y a su vez entrene a la población para los desafíos de la nueva globalización.

Jul 31, 2003

By M Shaffer, D C. Grant, D J. Goudie, P Sylvester, C Voisey

Scanning electron microscope–Mineral Liberation Analyser SEM-MLA can be used to discriminate between hematite/magnetite in iron ores, but achieving backscattered electron (BSE) segmentation between the two minerals is difficult for particles =75 µm using typical preparation and analysis methods for the MLA based on a tungsten filament SEM (Quanta 400) with 25 kV high voltage. Preparing iron ore sample mounts using a slow-speed polishing method, and conducting the experiment on a field emission gun SEM-MLA (Quanta 650) with the high voltage (HV) setting lowered to 15 kV reduces instrument noise and results in very clean BSE images and segmentation. This method requires new X-ray standards to be acquired for each mineral identity at 15 kV because of major changes in the spectra at lower kV. However, once these X-rays are added to the mineral reference list, effective segmentation can be achieved and a proper analysis obtained.CITATION:Grant, D C, Goudie, D J, Voisey, C, Shaffer, M and Sylvester, P, 2017. Discriminating hematite/magnetite via scanning electron microscope–mineral liberation analyser in the - mesh size fraction of iron ores, in Proceedings Iron Ore 2017, pp 541–548 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By C. Taschereau, G. A. Vickell, A. R. Laplante

Evidence in support of an iron-gold corrosion cell during the high-temperature/highpressure elution of loaded carbon is presented herein including, but not limited to, its discovery, mode of genesis, and confirmatory laboratory testwork. A discussion of metallurgical and economic impacts, remedial investigations, plant design considerations, and future work including mitigative possibilities is presented.

Jan 1, 2006

By Ian Thomson

The Social License to Operate ? We are operating in an era where social license in the resource industry is as important ? if not more important ? than mineral potential ? Concept proposed by Placer Dome executive Jim Cooney in 1997 as essential requirement for the future survival of the mining industry ? ?You don?t get your social license by going to a government ministry and making an application or simply paying a fee? It requires far more than money to truly become part of the communities in which you operate.? Pierre Lassonde, President of Newmont Mining Corporation (2003). What it is ?Granted by the local community ? Intangible, informal, non-permanent ? Has to be earned and then maintained ? Defined as ? Ongoing Acceptance (a lower level) ? Ongoing Approval (a higher level) ? Expression of the quality of the ?relationship?

Aug 1, 2013

By Gary B. Glass

Seventeen percent of US coal production now comes from the 19 surface coal mines in the Powder River Basin of northeastern Wyoming. The Powder River Coalfield, which coincides with this topographic and structural basin, is unique to the conterminous US, in that it contains an estimated 934.4 Gt (1.03 trillion st) of in-place coal resources. At least 13.2 Gt (14.6 billion st) is a compliant, strippable reserve base. In 1993, an estimated 162 Mt (179 million st), or 98% of the coal mined in this Wyoming coalfield, came from the thick - average 30.5 m (100 ft) - subbituminous, Wyodak coalbed, or from the Anderson and Canyon coals in the one mine where the Wyodak is split into two separate coalbeds. The other 2.7 Mt (3 million st) of coal mined in the Powder River Basin in 1993 came from the School, Badger, Monarch and Deitz No. 3 coalbeds. In this "world class" coalfield, there are at least 13 other persistent, 3 to 15 m (10 to 50 ft) thick, coalbeds as well as the Big George and Lake De Smet coalbeds, which are each 61 m (200 ft) or more thick in places. None of these latter 13 coals are mined at this time.

Jan 1, 1994