Search Documents

By Ghosh I, Vanangamudi M

Experiments have been made in a laboratory heavy media separator at various specific gravities of separation using zinc chloride solution and magnetite suspension as media for different types of coals. The results indicate that the magnetite bath gives at better separation than zinc chloride solution. Even though the probable error remains the same for most conditions of operation, the error area is found to have a wide variation which emphasises the importance of the error area over probable error in evaluating the performance of a cleaning unit.

Jan 1, 1981

By Tatsunori Matsumoto

In order to investigate the variation of the load-displacement relations of piles in a site, vertical load tests were carried out on 25 small diameter steel pipe piles. Out of 25 piles, 15 piles were close-ended pipe piles attached with a blade at the pile toe and 10 piles were open-ended pipe piles. To carry out these load tests in a short period, two types of rapid load test methods, Spring hammer load test and Falling mass load test, were employed. The load tests of all piles were completed in two days with 180 blows in total. In order to estimate a static load-displacement of a pile, non-linear damping method was used. It is shown from the test results that the performance of the pipe piles such as the ultimate pile resistance and the initial pile head stiffness is improved by re-driving.

Jan 1, 2006

Rutile Beach Sand from Hard Rock

Sep 13, 2010

By J. L. van Niekerk

The proposed Gautrain Rapid Rail Link (GRRL) will require approximately 15 km of double or twin high-speed rail track tunnels located for the greater part beneath the northern suburbs of Johannesburg, including Houghton, Rosebank and Sandton. During the Environmental Impact Assessment (EIA) it became clear that potential surface vibration above and in the vicinity of the tunnels was a matter of serious concern to the residents of the affected properties and that the impact required assessment. The general method proposed is based on a US Department of Transportation, 1998, publication in which abase vibration curve derived for typical high-speed passenger trains is adjusted for the topological, geological and other features to predict the surface vibration and the associated ground-borne noise. The predictions indicate that some isolated areas might be impacted but that the impact will likely be limited, and it is possible to mitigate the impact using suitable track construction methods and track support systems.

Jan 1, 2004

By J. Daavittila

In the latter part of the 1980s Outokumpu Chrome in Tornio, Finland, was in a situation when its twenty-year-old ferrochrome plant was becoming too inefficient to sustain economically sound production. The company made extensive studies on the then available processing methods to find out the best possible processing route. As a result, the whole plant was practically rebuilt and expanded. When equipment was proven in practical operation, an application for FeMn production was developed. Now as the Tornio FeCr-plant is considering expansion, the same type of exercise is to be performed with today?s challenges, which will be discussed in the paper. These challenges include increasing costs or decreasing quality of raw materials, increasing energy costs, stricter environmental regulations and demand for better working conditions. The possibilities of resolving to these challenges will be discussed in the paper. The future and continuing development with FeCr includes the better utilization of process dusts and a lower consumption of energy. By adapting the latest automation tools to better control the process, even higher efficiencies can be achieved with present technology. New processes are considered for development in the future and some possible technologies will be described.

Jan 1, 2004

By Turker L

The leaching of Tellness (Norway) ilmenite concentrate in hydrochloric acid and mixed aqueous HCl-alcohol solutions at boiling temperatures was investigated. It was found that the alcohols methanol, ethanol and ethylene glycol all substantially increased the leach rate and in the case of methanol and ethanol this was achieved at lower boiling temperatures compared with aqueous HC.

Jan 1, 1986

By Ashley P, Neale T

Alluvial gold was discovered on Sudest Island in 1888, and by 1893, an official production of 10 000 oz had been won by expatriate miners from shallow alluvial and colluvial workings. Hardrock sources were located and while one was developed at Mt Adelaide, production is unknown. Sudest Island comprises mostly phyllites and lesser coarse grained rocks which are cut by metamorphic quartz veins and basic (locally shoshonitic) intrusives. Sheared and altered basalts and serpent- inites represent are believed to be elements of an ophiolitic suite inferred to be associated with metamorphic core complex development and thus similar to tectonic environments on Misima and the D'Entrec- asteaux Islands. No epithermal-style quartz suggestive of a target similar to that on Misima Island has been identified on Sudest. A hardrock source for the alluvial and colluvial gold is interpreted to be metamorphic quartz veins similar to those in the Bendigo- Ballarat Zone of central Victoria, possibly remobilising gold derived from the meta- sedimentary and meta-igneous rock pile. The present focus is on development of a small scale alluvial gold mining operation in conjunction with exploration for hardrock targets. This latter programme remains at a reconnaissance stage.

Jan 1, 1991

By Eder Villarreal

La metodología presentada en este artículo permite valorizar propiedades mineras que se encuentran en etapa de prospección o de exploración básica, considerando el cálculo de un costo base y una evaluación cualitativa (en una escala de 0 a 5) de diez variables geológicas y económicas. Asignadas las calificaciones y otorgado un peso o grado de importancia a cada variable a través de un proceso analítico jerárquico (PAJ); finalmente se cuantificará la evaluación cualitativa mediante una operación matemática con dos ecuaciones, para obtener un rango de valor de la concesión minera en evaluación.

Feb 28, 2019

By L. R. Raymond

With the trend toward deeper and consequently hotter holes, measurements of drilling mud properties at atmospheric temperatures are becoming increasingly inadequate.' Both the prediction and control of down-hole mud properties depend in part upon our knowledge of temperatures in the wellbore. Consequently, a better understanding of factors that affect temperatures during circulation and trips could improve drilling operations. It was toward the goal of obtaining this understanding that this study was directed. Other investigators2 have studied the response of fluid temperature in the borehole during trips. However, all of these studies have used an assumed formation temperature profile at the conclusion of circulation and have provided no means to calculate this profile directly. In this study, the formation profile during circulation was calculated. Other investiga-tors3-5 have also studied bottom-hole temperature during circulation. However, they have developed neither general techniques for calculating the entire temperature profile in the system nor generalized methods for predicting bottom-hole fluid temperatures during circulation. Such techniques and methods have been developed and are discussed briefly in the following pages. Temperature Behavior During Circulation Circulation of fluid during the drilling operation is represented schematically in Fig. 1. The process of circulation has three distinct phases: (1) fluid enters the drill pipe at the surface and passes down the drill pipe; (2) fluid exits the drill pipe through the bit and enters the annulus at the bottom; and (3) fluid passes up the annulus and exits the annulus at the surface. To simulate the thermal behavior of the fluid in the system, each of the phases of circulation must be described mathematically. In Phase 1, the fluid enters the drill pipe at a specified temperature, TDo. As the fluid passes down the pipe, its temperature is determined by the rate of heat convection down the drill pipe, the rate of heat exchange between the drill pipe and the annulus, and time. Phase 2 of the circulating process merely requires that the fluid temperature at the exit of the drill pipe be the same as the fluid temperature at the entrance of the annulus; i.e., TD(L,t) = TA(L,l). Thus in Phase 3, the fluid enters the annulus at TD(L, t). As the fluid flows up the annulus, its temperature is determined by the rate of heat convection up the annulus, the rate of heat exchange between the annulus and the drill pipe, the rate of heat exchange between the formation adjacent to the annulus and the fluid in the annulus, and time. These rates of heat exchange and the time dependency of mud temperature are described by well known heat-flow equation.6 Consequently, as shown in the Appendix, the temperature profiles in the drill pipe, annulus, and formation can be obtained by solving Eqs. 1 through

Jan 1, 1970

One of the most common critical areas of longwall mining in terms of ground stability are the gateroad and bleeder entries. These critical entries provide much-needed safe access for miners and allow for adequate ventilation required for dilution of hazardous airborne contaminants and must remain open during mining of a multi-panel district. This paper focuses on the stability of the longwall entries subjected to a single abutment load such as bleeders, first tailgate, and last headgate. First tailgate and last headgate are also referred to as blind headgates and tailgates. A study of a longwall district through conditions mapping, support evaluations, and numerical modeling was conducted and evaluated by researchers from the National Institute for Occupational Safety and Health (NIOSH). The condition mapping and support evaluations were performed on entries that spanned the previous five years of mining and relied on a diverse selection of supports to maintain the functionality of the entry. Numerical modeling was also conducted to evaluate various support types with further investigation and comparison to the condition mapping. The study demonstrated the importance of the abutment load decay versus distance from the gob edge, the potential for a reduction in material handling related injuries, as well as optimal usage of secondary and standing support.

Jan 7, 2020

By Christopher Mark

A coal burst is defined as the sudden, violent ejection of coal or rock into a mine opening. Coal mines in the North Fork Valley (NFV) of Colorado?s Gunnison River have a long history of coal bursts in a wide variety of settings. These have included longwall and room-and-pillar, development and retreat, and single- and multiple-seam mining. In contrast to other coalfields, where bursts are typically associated with strong, massive sandstone and extremely high stress, many bursts in the NFV have occurred beneath shale roof and some distance from the most highly stressed locations. The goal of this paper is to attempt a systematic study of the entire burst history in the NFV, in order to gain insight into their characteristics and causes. The primary sources of information are the reports of investigations conducted by the Mine Safety and Health Administration (MSHA) Roof Control Division over the past 15 years. This paper provides details on the geologic mapping conducted as part of these investigations, as well as a regional plot of burst locations using a Geographic Information System. The mapping indicates that many of the NFV bursts have been associated with structural features, including low-angled faults and well-defined zones of high-density jointing that exhibit little or no displacement. Some of these features appear to extend for several miles, impacting more than one mine.

Jan 1, 2012

Simulation and Analysis of Media Behaviour in the Tower Mill by Discrete Element Method for Estimating the Power Draw and Spatial Distribution of Grinding Process The trends to the Tower Mill (TM) for grinding the materials are increased recently due to its unique merits. Among the various considerations of this machine, the main important items are increasing the efficiency of grinding as more as possible while keep the power consumption, manufacturing and maintenance costs as less as possible. Because this grinding process includes a huge numbers of media particles (ball or other shapes) that are interacted with each other and body of the machine, the DEM (Discrete Element Method) way is a very useful and essential step to getting confident evaluations. Because the DEM simulation is a very young scientific field and proper commercial software are very rare and still under modification, at first step, a FORTRAN code is developed for DEM simulation of two laboratory Tower Mill models (KM5 and KD5). The simulation and experimental results matched each other properly. Then one another DEM software was implemented to perform simulation of bigger models (huge numbers of balls), meanwhile could handle the complex 3D geometry data. The simulation and experimental results were compared and analysed in detail for not only laboratory but also for industrial models (KW5, KWD5, KWD50, KW300F, KW700F and KW1500) without any manipulation or compromising of the parameters of simulation. Some numeric data of industrial models are hidden here due to confidential reasons. The relative velocity of balls (ball-ball and ball-TM body), dissipate energy, interacted forces and stresses during the process are the key outputs of DEM simulation for design this machine. Therefore the main important processes in a Tower Mill machine are recognised and consequently some horizons of development of this machine are distinguished.

Sep 13, 2010

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of copper cementation with zinc in sulphate solution. For copper concentrations of the order of 10 p.p.m., a porous, adherent deposit is formed on the zinc surface and this has a significant influence on the reaction rate. When the specific mass of deposit is less than about O· 35 mg/cm2 the surface may be considered as smooth and the rate is described by simple convective counter diffusion of zinc and copper ions through a laminar diffusion boundary layer to the deposit-solution interface. In the presence of additional deposit, the diffusional mass transfer rate is increased by increased surface roughness.The rate under these conditions is first order, with the degree of enhancement independent of further increases in the specific deposit mass. The enhancement in rateis, however, directly related to the initial mass flux and the species involved in the reaction.Preliminary work showed the same mechanism to apply to cementation from chloride solution, solutions of high zinc concentration, and cementation of copper with iron..

Jan 1, 1970

The domestic mineral and material industry grew in some key sectors and declined in others during 1993; overall, the industry was poised at yearend for stronger growth in 1994. Metals production is expected to increase with anticipated growth in U.S. motor vehicle sales. There also may be increased demand for industrial minerals in 1994 based on domestic highway and building construction. Additional information on events, trends, and issues in the mineral and material industry is presented below and in the commodity sections that follow. Overall Industry Performance The value of processed materials produced from minerals in the United States during 1993 is estimated to have been about $326 billion, an increase of 5% compared with that of 1992. The estimated value of U.S. raw nonfuel minerals production in 1993 was $31.6 billion, about 1 % less than in the preceding year. The value of domestic minerals production has risen in 28 of the last 33 years.

Jan 1, 1994

By Barry Olson

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries to be developed in recent years. Goldcorp Inc. acquired the gold-silver-lead-zinc property with the acquisition of Glamis in 2006. The company has since committed US$1.5 billion to construct the mine, mill and associated facilities. The first of two 50-kt/d (55,000-stpd) mill and flotation lines is currently being commissioned while engineering and construction continues on the second line. A high-pressure grinding roll (HPGR) will ultimately take total throughput to 130 kt/d (142,000 stpd). The Peñasquito property is located in the northeast corner of Zacatecas state, Mexico. The elevation of the property averages 1,900 m (6,200 ft) above sea level and it is situated in a wide east-west valley. Except for one small outcrop (Peñasquito), the area is covered by up to 30 m (98 ft) of alluvium.

Jan 1, 2009

By M. K. G. Whateley, W. Hatton

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 20pp., 31 refs. Estimates of coal tonnage on UK open cast mining sites often vary from the recoverable tonnage. This is because the estimates depend on the geological variability of the coal measures. Geological parameters, such as thickness, quality and disturbance of the seam, have a direct control upon this variance. Risk analysis techniques have been applied using commercially available software to combine each parameter's variability into a cumulative variance, resulting in a tonnage distribution. Sensitivity modelling has also been used to identify the geological parameters which have the largest influence on the variance of the simulated tonnage distribution. An understanding of the relationship between the tonnage and geological variability has helped to focus exploration more efficiently. A cost to risk relationship can now be monitored, helping management to avoid negative consequences on site

Aug 1, 1995

By Walter C. Lorenz

In connection with its renewed study seeking solutions to problems created by release of acid water from bituminous coal mines, the Bureau of Mines recently surveyed reports already written on the subject. This publication is based on that search. The Problem Poor distribution of water is evident on an ordinary geographic map of the United States. The more abundant supplies of surface water appear to be centered in the northeast, the southeast, and the central humid areas of the country. It is in the midst of this abundant surface water, in the Ohio River Valley, that most of the bituminous coal is mined. Varied industry has located in the valley to use the coal and the river. The coal is a source of power and o raw material. The river provides transportation for raw and finished materials; equally important, it provides the water that is used for cooling and processing in manufacturing. It also serves as a vehicle for the disposal of waste.

Jan 1, 1962

THE choice of a pumping plant for the drainage of a mine is a matter of such importance that it is obvious that in a short paper it is impossible to go fully into the reasons governing the adoption of any particular type. The author, therefore, proposes to briefly discuss the methods.in vogue, and, as far as possible, to point out the advantages and disadvantages of the numerous systems. The probiem is of extreme importance to the mining engineer, and it appears that in the past sufficient thought has not been given to this branch, as shown by the numerous failures which are encountered.When water is met with in large quantities, the development of the mine depends upon the pumping plant to such a great extent that the most careful consideration should be given before deciding on any particular scheme for drainage. The pumpingplant in a mine should be looked. upon in the light of an insurance policy, and should be treated as such, care being taken that the premium is as low as possibl~, and to ensure this it is necessary that the most efficient plant be secured. Local conditions play such an important part ill the design of a plant that no hard and fast rules can be laid down. When the amount of water to be handled is small, and there is no possibility of any increase...

Jan 1, 1912

A process was developed, on a laboratory scale, for the removal of iron oxides from Weipa pisolitic bauxite. The technique involves the chemical reduction ofthe iron oxides by carbon, followed by selective removal of the iron species by acid leaching or chlorination.To remove more than 90 per cent of the iron it is necessary to reduce the iron oxides substantially to iron metal by heating the bauxite, pre-calcined at 650-800°C, with reactive carbon at 1040-1100°C. Reduction proceeds via the intermediate formation of hercynite (FeO.Al2O3) and difficulties have been encountered in reducing hercynite formed under less favourable reduction conditions.Following reduction, efficient selective removal of iron species is readily effected by acid leaching using dilute hydrochloric acid at 100°C, or chlorination at 500-750°C using Cl2, Cl2/N2, or Cl2/N2/CO mixtures.After removal of unreacted carbon, the final products contain 0·5-1.0 per cent Fe203 and 87-92 per cent Al203.

Jan 1, 1971

By B. J. Dave, Ashok J. Desai, Allen J. Hulshizer

This paper presents various design and construction considerations involved in developing an underwater installation of lined, large diameter shafts not known to have been previously accomplished for the diameter size, depth or ground conditions identified with the Seabrook Power Station. Outlined approach provides for driving tunnels independent of shaft sinking operation, permits the use of prefabricated shaft lining and incorporates a safe dry tap method for connecting the shafts to the tunnels. INTRODUCTION The Seabrook Power Station, located two miles inland from the Atlantic Ocean, at Seabrook, New Hampshire, is a two unit, nuclear powered, electric generating plant, each unit having a capacity of 1150 megawatts (electric). Typical to all steam driven generators is the requirement for large quantities of water. Requirements for the Seabrook Plant will be met by intaking and discharging approximately 850,000 gpm of ocean water at a considerable distance from the shore line in water depths that render the environmental impact inconsequential. Obtaining, conveying and discharging such large quantities of water represents a major undertaking, particularly under today's environmental controls. Tunnels are well suited to reducing the environmental impact at the Seabrook site by conveying the water about 250 feet deep under the salt marsh (a valuable ecological feature) and under the beach well out into the ocean without any noticeable ground surface disturbance. An alternate approach utilizing trenched piping would have created some disturbances and was environmentally less desirable. The tunnels connect to intake and discharge

Jan 1, 1976