Search Documents

By William A. Apel

Several different strains of bacteria have been shown capable of reducing hexavalent chromium, Cr(VI), to Cr(III), a less toxic, .. more readily recoverable form of Cr. This paper examined the Cr(VI) reduction efficacies of 3 different Cr(VI) reducing bacteria: Pseudomonas f1uorescens LB300., Pseudomonas aeruginosa PAOI, and Pseudomonas aeruginosa PAOI (pCROI) It was demonstrated that all three bacterial stratns reduced Cr(VI) primarily during their exponential growth phases while using glucose as their carbon and energy source. Significant differences in the three organisms' Cr(Vl) reduction capabilities depending on initial Cr(VI) concentrations were also demonstrated. P. aeruginosa PAOI showed superior Cr(VI) reducing capabilities over the. entire range of Cr(VI) concentrations tested while the Cr(VI) reduction capabilities of the other two strains were increasingly inhibited as Cr(VI) concentrations increased.

Jan 1, 1991

By Takeshita. Takuo

"In this work, the progress of the HDDR process is discussed mainly on the Nd-Fe-B magnet system. There are three technologies being used for the Nd-Fe-B permanent magnet production; the sintering technique, the rapid quenching annealing and the HDDR process. The HDDR process utilizes· the HDDR phenomenon, in which hydrogen absorbing intermetallic compounds go through as they are heated in hydrogen atmosphere, Hydrogenation - Decomposition Desorption - Recombination. In the HDDR process, these four steps in the HDDR phenomenon are processed by choosing suitable reaction conditions regarding to hydrogen gas pressure, temperature, rate ·of desorption and etc., and we can produce permanent magnet powders of good magnetic properties with microstructures consisting with sub-micron size crystalline grains. In the anisotropic magnet powders, the sub-micron size crystals are being mostly aligned in the crystallographic c-axis direction. Possible applications of the HDDR process to other systems are also discussed.Microstructures of the Nd-Fe-B Permanent MagnetsIt is well known that magnet properties of magnetic materials are very sensitive to their microstructures [l]. This is seen in almost all magnet materials from soft magnetic materials and hard magnetic materials to magnetic memory materials. In this regard, the production technology is very important for the control of microstructures of permanent magnets The Nd-Fe-B magnet is the most powerful permanent magnet as a practical permanent magnet, and its coercivity force is much dependant on the microstructure as is the case for other permanent magnets."

Jan 1, 2000

By Zhongliang Tian, Yun Cheng, Yexiang Liu, Ming Jia, Yanqing Lai

"A fundamental electrochemical study of Si ions in Na3AlF6-LiF melts and electrolysis using liquid cathodes was conducted. Cyclic voltammograms (CVs) clearly showed the depolarization of silicon deposition on liquid cathode by forming chemical complexes with the liquid solvent metals. Besides, co-deposition of Al and Si is possible when Si ions are insufficient in the molten salt. Based on the electrochemical results, silicon diffusion into liquid cathode is modelled and evolution of Si activity with concentration is deduced by a mathematic approach. Electrochemical study using liquid metals as working electrodes, can be used as an alternative approach for the acquisition of basic data on alloy behavior. Galvanostatic electrolysis showed that liquid cathodes are appropriate to collect the deposited solid silicon and the highest collection efficiency is almost 85%.IntroductionRecent years have witnessed an increasing demand for solar-grade silicon (Si) by the photovoltaic industry [1-4]. The preparation of high-purity metals through electrolysis and electrorefining offer many advantages such as low cost, low-energy consumption, and environment-friendly process, and thus has been widely used worldwide. From the perspective of electrochemistry [5-7], by utilizing the electronegativity difference between the impurities and Si and controlling the relevant process parameters, it is possible in principle to electrodeposit monatomic Si from a Si4+-containing compound melt. Moreover, because the carbon content of the high-purity Si obtained through electrolysis can be effectively controlled and used as a very ideal raw material in the preparation of electronic-grade and solar-grade Si, the preparation of high-purity Si through electrolysis has received widespread attention [8,9]. Monnier et al. [9] used a graphite electrode to obtain high-purity Si (99.9 %-99.99 %) from Si02/Na3AlF6 system through electrolysis; however, because the Si was precipitated in a solid form and showed poor conductivity, the deposition rate was too slow. Olsen et al. [10] obtained high-purity Si films via electrodeposition in K2SiF6/KF-LiF system by selecting electrode materials with high surface quality (such as Ag and graphite). However, in order to ensure the film quality, the deposition current density must be relatively low (10-50 mA/cm2), resulting in a low current efficiency and low deposition rate, which are not conducive to reducing energy consumption and applying to practical use"

Jan 1, 2014

By Claudia Gasparrini

Uranium occurs in a variety of minerals, the more common primary ones of which are uraninite-pitchblende, coffinite and a group known as the complex multiple oxides. Identification and description of the uranium-bearing and associated minerals in ore samples may give a preliminary indication of the potential economic importance of the deposit and may also suggest initial approaches to metal extraction. The present paper reviews the common uranium minerals, describes their manner of occurrence and compares the types of deposits with which they are associated. Methods and techniques for their identification are described and their leaching characteristics discussed.

Jan 1, 1981

By N. El-Kaddah, J. W. McKelliget

"A mathematical model for the analysis and design of hybrid plasma reactors for advanced materials synthesis is presented. The model is based upon a solution of the electromagnetic vector potential equation and is capable of predicting the two-dimensional velocity, temperature, and electromagnetic fields as well as the reaction kinetics inside the reactor for any axi-symmetric coil configuration. The model is used as a computer aided design tool for the design of hybrid plasma reactors consisting of a conventional DC torch augmented by an RF induction coil and it is demonstrated that the hybrid system possesses superior characteristics for materials synthesis over conventional DC or RF systems. The coupling between the RF and DC components is found to affect both the temperature field and the flow field and to have a significant effect on the reaction kinetics and on materials recovery. The model is used to study the thermal decomposition of silicon tetrachloride as a function of reactor design and operating parameters and it is demonstrated that through a CAD approach it is possible to significantly improve the operation of materials synthesis systems.IntroductionIn recent years there has been growing interest in the use of the inductively coupled plasma for chemical synthesis as a way of meeting the increasing demand for high quality, high performance materials for use in critical applications/l/. Although the basic feasibility of this approach has been demonstrated in the laboratory/2,3/ there still exists a number of operational problems that adversely affect system performance for some applications. In particular, the recirculation and back flow effects that arise from the electromagnetic forces in the plasma can result in the repulsion of the reactants from the hot plasma core and their subsequent deposition on the walls of the reactor. Another operational problem arises from the fact that the energy dissipated in the plasma has to compensate for the heat losses to the environment by conduction, convection, and radiation in order to maintain the ionization of the plasma and, hence, the stability of the plasma may be affected by the presence of the reactants and their products."

Jan 1, 1988

By J. N. Hryn

This paper describes some of the work done in Phase 1 of a multi-year, five-phase program aimed at demonstrating the economic feasibility of producing commercial-scale quantities of commodity materials derived from salt cake residue-oxide. The amount of salt cake generated annually in the U. S. is estimated to be 510,000 tons, including 340,000 tons of residue-oxide. Used beverage can (UBC) processing accounts for the majority of residue-oxiae that could be made available for further processing into commercial products. To characterize the composition of residue-oxide. eight residue-oxide samples from various secondary processors were obtained and analyzed. Surprisingly, the composition of residue-oxide was found to be independent of source or alloy family being processed, with? the exception of slightly elevated silicon levels in 3XXand UBC residue-oxide samples. Major phases detected in the residue- oxide were? alumina, spinel, and aluminum hydroxides. Preliminary economic analyses indicated that the refractory market appears to be the best choice for high value-added products produced from residue-oxide with minimum processing. Bench-scale tests indicated that low silicon containing residue-oxide is ready to enter this market, but the elevated silicon content of UBC and 3XX residue-oxide preclude this possibility. A separation technology should 'be developed to remove silicon-containing . species from the alumina and spinel values Present in residue-oxide. This technology would then allow UBC and 3XX residue-oxides to be converted to significantly higher value-added products.

Jan 1, 1995

By Jack S. McPartland

Historically, research on thiosulfate leaching of precious metals ores has been focused on processing of difficult to treat ores. Thiosulfate leaching of ores and concentrates containing sulfide minerals, copper, manganese and preg-robbing carbon constituents has been evaluated. Cyanide leaching is generally considered an efficient, environmentally acceptable means for processing of non-refractory precious metal ores, Consequently, commercial processing of finely disseminated, oxidized precious metal ores is normally accomplished using alkaline cyanide leaching. Recent changes in regulatory climate have, however, called into question the acceptability of cyanide leaching in a number of locations worldwide. In some cases where the use of cyanide is being questioned, thiosulfate leaching may provide an acceptable alternative. Developments in thiosulfate leaching of precious metal ores are reviewed in this paper.

Jan 1, 1999

By De-qing Zhu, Jian Pan, Tie-jun Chun, Dong Chen, Yu Cui

"A study of processing pyrite cinder and metallurgical slag using “one step” technology in strand grate - rotary kiln is presented, which aims to efficiently recover the valuable metals of iron, lead, zinc and copper. The effect of chloridizing roasting parameters including roasting time and temperature on the removal rates of nonferrous metals was investigated. It is shown that copper and zinc are difficult to remove and lead is removed more easily. The preheated pellets were reduced in a rotary kiln, where zinc and lead can be removed easily and high iron grade and good metallurgical performance prereduced pellets can be obtained. Furthermore, the chlorination and the reduction mechanisms of copper, lead and zinc are discussed. It is revealed that the phases of copper, lead and zinc in slag are complex and ferrite and silicate of metals are difficult to remove.IntroductionAs two kinds of significant secondary resources, metallurgical slag and pyrite cinder contain not only abundant iron but also considerable copper, lead, zinc and so on. Several tens of millions of tons of metallurgical slag and pyrite cinder are discharged in nonferrous metal and chemical industries annually in China [1, 2]. In addition, the accumulated waste slag in storage is more than one hundred million tons, which not only occupies much land but also pollutes the environment [3]. However, because the metallurgical slag and pyrite cinder are treated by high temperature processing, the properties are distinctly different from the properties of natural ores, and iron is in close association with copper, lead and zinc. So, metallurgical slag and pyrite cinder are difficult to efficiently utilize and only a small amount is used as additives in cement, paving, brickmaking and auxiliary additives [4-7]."

Jan 1, 2011

Direct electrowinning is an electrochemical process which has been developed for the extractive recovery of copper from dilute, acidic leach solutions. In passing through a thin particulate coke cathode. copper is reduced and electrodeposited in a thin layer forming a solid copper-coke sheet. The product is melted in a furnace to separate the coke, then the molten copper is fire refined to produce a salable product. A description is given of a prototype unit which is designed to treat 20 gpm leach liquor and recover over 100 pounds of copper per day. Economic analyses show that in a commercial facility producing about 25.000 TPY copper.*the direct electrowinning process has lower overall cost than either conventional iron-cementation or the newer liquid ion exchange-electrowinning when the leach liquors contain less than 2 grams per liter of copper.

Jan 1, 1976

By J. T. Stanley

The identification of crystal phases and crystal chemistry can be critical to understanding the mechanisms of waste material interaction with native soils. Understanding these mechanisms can suggest correct methods for remediation and treatment. A program is outlined and examples are given of the development of effective techniques for rapid phase identification of environmental samples using electron microscopy. The program concentrates on the development of integrated object oriented software to aid rapid searching of online databases and rapid simulation of potential crystal diffraction patterns. Examples come from dried sludge taken from a former hard-chrome plating facility.

Jan 1, 1993

By R. H. Rubisov

Sulphuric acid pressure leaching of nickeliferous laterites has attracted considerable attention from the nickel industry during the past five years. The process is especially advantageous for limonitic laterites that mostly contain goethite, because iron precipitates releasing acid and thus rendering low acid consumption. It is also applicable to mixtures of limonites and saprolites, although at higher acid consumption due to magnesium. Effective process design requires the solubility of metals that precipitate during the process to be known. In the present work, determination of metal solubilities is based on a simple speciation program that assumes the presence of only one dominant complex for each metal. The thermodynamic data for the precipitation reactions are extracted from high-temperature experiments with monometallic systems published previously. The validity of the approach is then tested against mixed bimetallic systems, and finally applied to calculate the solubility of aluminium, iron and magnesium in laterite leaching effluents "at temperature". In both cases of limonitic feed and limoniticfsaprolitic blends, the prediction closely follows metal solubilities measured experimentally at temperatures from 230 to 270°C and at terminal he acidities ranging from 10 to 75 g/L.

Jan 1, 1999

By C. Beckermann

"A diffuse interface model is derived for the direct simulation of two-phase flows with surface tension, density differences between the phases, and phase change. The derivation starts from the balance equations for a sharp interface and uses a formal averaging procedure on an atomic scale to obtain diffuse interface versions of the equations. Two approaches are considered: (i) the two phases have different velocities inside the interface and separate conservation equations are solved for each phase, and (ii) the two phases have the same velocity inside the diffuse interfuce and mixture conservation equations are solved. Based on a superposition of microscopic (atomic-scale) and macroscopic interface morphologies, an expression for the interfacial momentum source term is introduced that models surface tension effects and accounts for immiscibility between the phases.IntroductionDiffuse interface methods have been a popular tool in the direct simulation of two-phase flows [I]. In diffuse interface approaches, the interface between the two phases is characterized by a rapid but smooth transition in the properties, such as density and viscosity. Usually, a phase function ? is introduced to represent this transition, and the evolution of ? in the domain is computed from a separate equation or recipe. A unique set of conservation equations (e.g., mass and momentum) is solved on the entire domain, irrespective of the phase present, by accounting for the transition in the properties and introducing terms that account for interfacial sources. The continuum surface force (CSF) model of Brackbill et al. [2], which accounts for surface tension, is an example of the latter. The volume-of-fluid (VOF), level set, and phase-field methods are all examples of diffuse interface approaches. The major advantage of diffuse interface methods is that explicit tracking of the interface and the application of traditional sharp interface conditions are avoided. A disadvantage can arise from the artificial smearing of what is in reality an interface of atomic-scale width; however, techniques have been developed to overcome this problem."

Jan 1, 2004

By Bo Zhou

During secondary aluminum recovery, complex aluminum scraps are melted and refined often in a rotary melting furnace and the aluminum metal has to pass through a molten salt layer and melt down in a bottom aluminum bath. Previous experimental study and industrial observations have indicated that salt shell formation and re-melting on the metal solids in the early stage plays a critical role in the overall melting process of the scrap. In the present paper, mathematical models are developed to simulate the process of salt shell formation and its re melting, as well as aluminum melting in the molten melt. Influence of the salt layer properties, the residence time of the metal particles in the salt layer, the particle size, the temperature of bulk melt were investigated. Reasonable agreement with the measurement data was reached. The developed melting model will be used to construct a population balance model of the scrap melting behavior for a rotary melting furnace, taking into account the distributed characteristics of the scrap. Finally, an overall process model based on Computational Fluid Dynamics (CFD) for the rotary furnace will be constructed, coupling with the population balance model for the scrap melting.

Jan 1, 2003

By Toyohisa Fujita

The effect of variables on the gold extraction with ammonium thiosulfate was investigated on sponge gold and ore samples. The Effects of CUS04, (NH4hS203, NH40H, (N~hS04' pH, stirring speed and retention on gold leaching rate and thiosulfate oxidation (consumption) have been studied. Almost 100% of gold was leached from sponge gold and over 96% from ore sample at optimum conditions. Trioctylmethyl ammonium chloride was used to recover gold from thiosulfate pregnant solution. It was found that more than 99% of gold was recovered by the extractant diluted with n-octane at 01 A ratio of 1: 1 without the re-adjustment of pH or others. Also, the gold cementation was conducted without de-aeration by using zinc, copper and aluminum powders. The result indicated that the gold was effectively recovered from a solution of low ammonia and copper concentrations and higher thiosulfate concentration. The gold recovery process by using ammonium thiosulfate is an environmental friendly method comparing to conventional cyanidation process.

Jan 1, 2003

By David J. Howard, Christine Broadbridge, David C. Paine

"High pressure vapor/solid reactions offer an opportunity for novel synthesis and processing of thin film materials and structures for electronic, optical, and magnetic applications. In this paper we review the use of two high pressure techniques that operate from 25 to 1000 atm (2.5 to 100 MPa) to fabricate thin film oxide structures from Si1-xGex deposited on Si wafers. High pressure synthesis enables temperature-independent control of reaction rates in the oxidation of this multicomponent semiconductor system and hence offers the opportunity to form thennodynamically metastable Si1-xGex<h from the alloy. The thermodynamics of the Si-Ge-0 system are reviewed and a method is described that utilizes selective chemical reduction (via H2 gas) of Si1-xGcx<h to form Ge precipitates in an SiO2 matrix. IntroductionAlloys of Si1-xGex grown epitaxially on Si substrates by chemical vapor deposition (CYD) and molecular beam epitaxy (MBE) have been used to create high performance microelectronic devices1. These devices show improved performance over conventional Si technology because they exploit the Si/Si 1-xGex band-gap discontinuity and take advantage of higher hole mobilities in the Ge containing alloys. While a range of devices based on heteroepitaxial systems have been demonstrated, the Si1_xGex alloys are of particular interest because they are most closely compatable with standard Si device processing. One disadvantage of Si-based materials systems is that they are not typically useful emitters of light. This is important since the use of light (rather than electrons) for transmitting and processing signals into, out of, and within Si-based microelectronics would represent a major technological advance in microelectronics-based communication and computer technologies. Nevertheless, through the use of innovative processing techniques it may be possible to use the Si1_xGex/Si heteroepitaxial system in integrated microelectronic/light-wave technologies."

Jan 1, 1994

By R. Boom, C. F. Balentina, J. H. L. Voncken

During vitrification of bottom ash generated from the combustion of municipal solid waste (MSW), a Fe-Cu based alloy phase with great value was formed. In order to find proper commercial use in metallurgical industry, it is necessary to separate Cu and Fe. The present study focuses on the sulfide treatment at temperatures of 1400 – 1500oC, in particular with FeS containing minerals. Various sulfide compounds such as Na2S, Al2S3 and Ni3S2 were added to promote the copper removal. Pyrite and zinc sludge (containing ZnS) as waste streams were studied with specific interests. The results showed that both zinc sludge and pyrite are effective for copper removal with the highest removal efficiency of 95% by using pyrite. The copper content drops from 12 wt% to about 2 wt%. However, it is still difficult to remove copper completely from the alloy in one step, and a multi-step operation is needed.

Jan 1, 2008

By Yong Zhao, Yan-hui Sun

Behaviors and evolutions of MgO·Al2O3 in non-oriented silicon steel during calcium treatment were investigated by thermodynamic calculations and high-temperature experiments. MgO·Al2O3 inclusions were the main type of inclusions before calcium treatment, which is also confirmed by the stability diagram of MgO/MgO·Al2O3/Al2O3 from thermodynamic calculations. After calcium treatment, the majority of original MgO·Al2O3 inclusions were mainly modified to CaO-MgO-Al2O3 system inclusions, this would be beneficial to improve castability and product quality of silicon steel. But there was no modification happening to some MgO·Al2O3 spinels which were directly surrounded by CaS inclusions. The content of Al2O3 occasionally existed a sudden increase besides a common decrease in the product layer of CaO·MgO·Al2O3. Then the evolution mechanisms of MgO·Al2O3 inclusions were proposed in present work. Thus, Al/Mg atom ratio had a significant influence on the modification of MgO·Al2O3 spinel.

Jan 1, 2016

By T. K. Mukcherjee

The importance of the processing of secondary resources such as solid industrial wastes and liquid effluents as well as byroducts for the recovery of the associated metal values hardly needs any elaboration. Such processing contributes in no small measure.towards the augmentation of the availability and the supply position of resources. As an added benefit, it leads to a reduction in environmental pollution caused by the undesirable waste materials. As some typical examples of secondary resources in the Indian scenario, mention&apos; can be made of spent catalysts, metal/alloy scrap, ash, consumed batteries, flue dust, slag, sludge and slime, pickling solutions, spent acids; plating rinse solutions, spent etchants, waste water from synthetic fibre manufacture and from tanneries etc. These wastes constitute a source of a variety of non ferrous metals. In the processing of secondary resources like these, the techniques of hydrometallurgy such as solvent extraction play a pivotal role. This paper outlines the efforts made to use solvent extraction to recover(1) base metals. such as copper, zinc, nickel and cobalt from a number of secondary resources like cake, and sludge(2) refractory metals like molybdenum and vanadium from sulphidic byproducts and spent catalyst and (3:) nuclear metal like uranium from phosphoric acid. In the case of base metals, process flowsheet involving the use of acidic extractants such as DEHPA and PC88A have been optimised. The problem of iron removal from the leach liquor, "which influences the metal recovery process significantly, has drawn a special emphasis. hi the case of refractory metals, basic extractants .like Alamine 336 has been pressed into service to produce kilogramme. quantities of pure salts of molybdenum and vanadium, Finally, the paper gives a brief account of plant experience in recovering uranium from phosphoric acid, using &apos;a solvent system comosed of DEHPA and TOPO.

Jan 1, 1996

By F. Leuzzi

Asbestos is a natural mineral fibre which has been known and utilized commercially for about a century. From the forties, it was employed on an ever-increasing scale throughout the mechanical engineering, building, paper-making and plastics sectors, to name but a few. There are essentially five minerals which provide fibres for industrial applications, namely, the chrysotile variety of serpentine and the amphiboles such as riebeckite, anthophyllite, cummingtonite-grunerite (amosite) and tremolite. About a fifth of the world&apos;s asbestos output was once taken by Europe for the manufacture of asbestos-cement products, reinforced plastics, paper and cardboard, panels, soft insulation and spray-on powders. However, in the sixties and seventies the hypothesis regarding the pathogenic nature of asbestos fibres started to gain ground. Moreover, between the sixties and eighties the EU issued a series of regulations designed to bring about a steady decrease in asbestos consumption. This line of action has culminated in recent years in a whole set of directives banning the use of asbestos in all products. This created a major problem, namely, how to clean-up the several million tons of various types of asbestos products in various states of conservation existing in Western Europe. CORDIAM (Pat. RM95 A 000269 and Pat. RM96 A 000782 in the name of ECOTEC S.r.1.) is one of the thermal inertization techniques recently proposed for this purpose. The process provides for the low-temperature ceramization of the toxic-harmful material. Of course, with such a great variety of waste materials and the volumes to be treated, as well as the need to ensure the correct dimensional design of the thermal sections of the treatment plant, it is necessary to know as much as possible about the thermal behaviour of the wastes concerned. This paper details the steps taken firstly to ascertain the thermal behaviour of such materials as may be encountered in day-to-day practice and secondly to examine the influence of the main process parameters on the preliminary design of gas- or fuel-oil-fired rotary kilns of the kind used for waste treatment.

Jan 1, 1999

Gas flow and heat transfer phenomena in two industrial-scale waste-heat boilers of the Outokumpu copper flash smelting process were analyzed with a commercial computational fluid-dynamics (CFD) package Phoenics. Various operating conditions were simulated for the first boiler and particularly for the second boiler. The gas flow pattern was compared qualitatively with the physical laboratory models, and the general flow pattern was consistent with the laboratory visualization. The heat transfer simulation was validated with, temperature measurements for both boilers, and good agreement was reached between the computed temperature profiles and the measured data. The computational results indicate that gas flow in both boilers is of three-dimensional and recirculating nature. The numerical tracer experiments indicate that some dead volume is present in both boilers, and the boiler modification reduced the dead volume from 38% to 15% under basic operating conditions. Radiative heat transfer accounts for 65-90% of the total &apos;heat transported in the radiation sections of both boilers under different operating conditions. The modified boiler is very efficient for cooling the off-gases at almost doubled volume flow rate. The CFD modeling proved to be a useful tool for numerical experiments and analysis of boiler performance for process: optimization.

Jan 1, 1998