Search Documents

By G. Kugler, M. Tercelj

"The 1.2690 high alloyed tool steel is usually applied for cold working and is alloyed with carbide-forming elements Cr, V, W and Mo. It exhibits very poor hot deformability. Since there is no enough available data in literature for elucidation of this problem, hot workability and development of microstructure during hot deformation was studied. Hot compression tests were carried out in temperature range 850-1150 °C and strain rates range 0.001-6 s-1. SEM and OM were used for observation of microstructure. Results revealed very complex precipitation of carbides that depends on deformation temperature as well as on strain rate. It was found that especially at lower temperatures of hot working range the precipitation of carbides strongly depends on strain rate. Three different hot deformation behaviors’ were observed depending on temperature and strain rate range.IntroductionThe hot workability of highly alloyed high speed steels is usually described as relatively poor in comparison to other steels due to their tendency of cracking during hot working especially when inappropriate hot working conditions are applied. Alloying elements such as Cr, W, Mo and V in ledeburitic tool steels form carbides that improve hardenability, strength, hardness, wear resistance, etc., but they decrease hot workability and narrow hot working temperature range in comparison to conventional steels. The size, distribution, type and fraction of carbides, as well as the thermomechanical history of material and hot working parameters have major influence on the hot workability. The microstructure of ledeburitic tool steels during hot deformation can be characterized as a two-phase system consisting of an austenite matrix and a combination of ledeburitic carbides [1-4]. In the soft-annealed condition the total volume fraction of carbides is in the range 19-30% and in the quenched condition in the range 9-25%, depending on the chemical composition. During heating before deformation a large quantity of carbides dissolve, but non-dissolved carbides can have an extremely diverse influence on the hot workability due to variations in their composition, size, distribution, hardness and shape, and their different behavior during the deformation phase [5-7]."

Jan 1, 2011

By Peter G. Cooper

"During 1987, the feasibility of modernising the ER&S smelter at Port Kembla, NSW, Australia was studied. The selection of appropriate technologies to carry the smelter into the 21st century considered issues such as capital cost, existing infrastructure, feed mix, capacity, product quality, flexibility and potential for further development. Both hydrometallurgical and pyrometallurgical process schemes were considered. Some novel combinations were assessed but ultimately rejected. Final technology selections included proven smelting and anode furnace processes, pyrometallurgical slag cleaning and modifications to existing equipment. This process scheme balanced risk against development potential within the constraints imposed by the existing plant.BackgroundThe Electrolytic Refining and Smelting Company of Australia (ER&S) has operated a custom copper smelter at Port Kembla since 1908. Existing technology includes a sinter plant/blast furnace, three small Peirce Smith converters, two reverberatory anode furnaces and a conventional tankhouse. These process units were all installed prior to 1960 and have proven to be flexible enough to process the wide variety of domestic feed materials purchased by ER&S.However, by the early 1980s, threats to domestic concentrate supplies highlighted the need for major changes to reduce operating costs to world competitive levels. Various studies in the ensuing years failed to identify an economically attractive solution. Furthermore, pressures were increasing to improve the environmental performance of the smelter.During 1986 the options for redevelopment were again considered and by the end of 1987 technologies for the retrofit had been selected and a full feasibility study was completed."

Jan 1, 1988

By T. C. Goel, A. Venna, R. G. Mendiratta

"Processing of ferrites has gained tremendous importance in recent times to meet the high performance demands on ferrites in keeping with the fast emerging· technologies. The quality of ferrite powders has strong influence on ·the performance of final device. Fabrication· of high performing ferrite components requires starting ferrite powders of precise stoichiometry, purity and microstructure. It is difficult to obtain these attributes by the conventional ceramic method. The key to obtaining quality powders lies in the· solution techniques. With this in view soft ferrites have been prepared by a wet chemical process, known as the citrate precursor method, which involves the formation of citrate complexes of the constituent cations. The advantages of this process are the ease of preparation and close control of composition, homogeneity, purity and particle size. Electrical and magnetic measurements on lithium ferrites have shown resistivity higher by more than two orders of magnitude compared to that observed for samples prepared by the conventional ceramic method, and low magnetic losses, making the ferrites specially suitable for high frequency applications.IntroductionProperties of ferrites are known to be sensitive to .their processing technique. A small deviation in the compositional stoichiometry of the ferrite affects its properties greatly. Soft ferrites such as Ni-Zn, Mn-Zn and Mg-Mn. are well known ferrites covering wide-ranging applications [1,2]. Lithiiim ferrites have also assumed technological importance for microwave applications and are potential substitutes for the expensive garnets [3]. Lithium ferrites are often doped with zinc to tailor the saturation magnetization required at high frequencies. Lithium and lithium-zinc ferrites, however, present difficulty to processing due to the volatile nature of both the cation components, namely Li and Zn. These ions are volatile at temperatures > 1000°C which makes their processing difficult. One of the main considerations of high frequency performance of ferrites is the high eddy current losses which prevent the interaction of the magnetic field with the ferrite component and hence impair device performance. These losses can be reduced by having a material of high resistivity. Electrical conductivity in lithium ferrite has been attributed to electron hopping [4] between the two vaience states of iron, Fe2+ <=> Fe3+, on octahedral sites. Maintaining the + 3 valence state of otahedral- Fe ions is thus a prerequisite for achieving high resistivity. The resistivity of ferrites is normally found to be low when processed by the conventional solid-state or the ceramic method [5]. This is attributed to (a) extensive ball-milling employed in the method to mix the component oxides results in non-stoichiometric compositions due to introduction of additional Fe ions on abrasion of steel balls during milling, (b) high processing temperatures involved which result in significant volatilization of Li and Zn ions creating thereby oxygen non-stoichiometry which results in reduction of Fe3 + to Fe2 +, (c) large and non-uniform grain sizes. In the present work, preparation of Li and Li-Zn ferrites by a non-conventional method known as a citrate precursor method [6, 7] which requires lower processing temperatures and duration is reported. The method gives stoichiometric compositions on account of homogeneous atomic-scale mixing of the constituent cations via the formation of metal-citrate complexes mixed in solution state. The method is also capable of giving small grain size which aids the oxidation ofFe2+ ions."

Jan 1, 2000

By Nagy El-Kaddah

One of the emerging technologies for the production of ultra-clean metals is electromagnetic filtration. The theory and the mechanism of electromagnetic separation of inclusions from molten metal are briefly reviewed along with basic electromagnetic separation systems. This paper focuses on inclusion removal in the induced current separators, with specific reference to a new separator developed at the University of Alabama. A simple analytical model is presented for the analysis of particle separation in such a system. The role of the applied magnetic field on inclusion removal will be discussed. It is shown that particle velocity increases exponentially with increasing magnetic field strength. At moderate field strengths, the velocity of 50 to 100µ inclusions are an order of magnitude larger than those achieved by buoyancy. The separator developed at the University of Alabama is described together with experimental results of laboratory and large scale experiments on purification of molten aluminum. These results demonstrate ?the capability of the system for producing super-clean metals.

Jan 1, 1996

By Garrett May

We present a periodic technique for measuring the thermal conductivity of thin, disk-shaped samples. In samples of this type, temperature measurements must be made across the sample faces and are therefore subject to large error due to the interface resistance between the temperature sensor and the sample. The technique uses measurements of the amplitude and phase of the periodic temperature across both a reference sample and the unknown material at several different frequencies. Modeling of the heat flow in the sample allows the simultaneous determination of the thermal parameters of the sample as well as the interface resistance. The technique is demonstrated on nanocomposite samples less than 1.0 mm thick.

Jan 1, 2008

By E. Fockedey

he destruction of free cyanide on a Co3O4 doped carbon felt was studied. The experiments were done with an eiectrochemical filter press cell on dilute alkaline solutions containing 250 mg/l NaCN. No chloride ions were added to the solutions. The cobalt oxide protects the felt against corrosion and has a catalytic effect on the degradation of the cyanide. This kind of electrode allows working with current density as high as 1200 Aim without any visible degradation of the felt. The most interesting results were obtained with a current density of 400 Aim&apos; at which the cyanide concentration can be lowered to 5 mg/l with a current efficiency of more than 70 % and a specific energy consumption of about 10 kWh/ kg CN.

Jan 1, 1998

By J. Howarth

Two electrochemical processing methodologies have been used to electrogenerate bromine-laden solutions for gold-leaching purposes. In the first process, a laboratory-scale cell in which the anode and cathode compartments were separated by a cation-exchange membrane was employed. The bromine produced by electrolysis of a 4% bromide solution was used to leach gold from a low-grade ore. The pregnant leach solution was then returned to the cell to recommence the cycle. High current efficiencies (90-93%) were maintained over six cycles. In the second process, an undivided hypochlorite generating cell (Chloropac"&apos;) was used to generate bromine from a simulated leach solution. Electrolyses were performed on a pilot-scale (100-150 gallons) with solutions containing different levels of bromide ion. The current efficiencies were also high (80-90%) and unaffected by the bromide concentration (over the range 2.5-5%) provided the electrolysis was run to low conversion « 15%). The Chloropac module was capable of delivering 0.6 kg bromine per hour at a power cost of $0.09 per kg. Using these figures, a detailed economic assessment for a 1000 metric tonnes (MT) per day gold ore processing plant was made. Electrolytic regeneration of bromine in a gold leach/recovery circuit dramatically improves the process economics over cyanidation.

Jan 1, 1991

By William D. Riley

The U. S. Bureau of Mines has developed technology to recover by-product materials from aluminum scrap using engineered scavenger compounds (ESC). ESCs are structural oxides with a channel or tunnel structure that allows them to hold ions of a specitksizes and charges. The scavenging reaction is easily reversible allowing the ESC to be recharged for continued use and the ion is recovered as an electro deposit. Key features of this novel technology are; a) ESC ,systems are designed to have a high degree of selectivity for a desired ionic species. b) The recovered mater.ial requires little or no additional reprocessing prior to reuse. Two current uses for the ESC technology that are described in this paper are the removal and recycle oflithium (Li) from lithium aluminum (Li-AL) alloys; and, using ESCs as a replacement for the conventional demaging (magnesium removal) technology used by the secondary casting industry. Research indicates that the ESC technology proposed for both these applications has either &apos;distinct economic and/or environmental advantages over previously employed methods of recovering. metal values from aluminum scrap.

Jan 1, 1995

By Ray Y. Lin, Sunil G. Warrier

"Low cost processing of metal matrix composites is an essential requirement for this class of materials to be acceptable in commercial application. In an effort to reduce the cost of processing of metal matrix composites, an infrared pressureless liquid infiltration technique has been developed. The salient features of infrared infiltration are that it is rapid, simple and a low cost process. The rapid processing capability causes very little oxide formation on the alloy resulting in both improved wetting and flow characteristics and reduced oxygen contamination in the composite. Thus, vacuum is normally not required. Using infrared inflltration, aluminum and titanium matrix composites have been prepared under an ambient argon atmosphere. Reinforcements in these composites include carbon fibers, silicon carbide Nicalon fibers and Textron's SCS fibers. Microstructural and mechanical test results indicate that completely consolidated composites with good fiber distribution, limited interfacial reaction and high mechanical properties can be manufactured by this process. IntroductionAluminum and titanium matrix composites reinforced with ceramic reinforcements are strong candidates for numerous applications in the aerospace and automotive industries. Aluminum matrix composites are commonly fabricated by either solid state vacuum hot pressing, liquid state pressure infiltration or squeeze casting [1]. Although liquid state pressure infiltration and squeeze casting has significant advantages over solid state processes, the requirement for pressure makes these composites uneconomical for large scale industrial application. Titanium matrix composites are primarily fabricated by solid state diffusion bonding [2]. Pressureless liquid infiltration can significantly reduce the cost of fabrication in both the composite systems. However, during pressureless infiltration processes, several complications concerning the wetting characteristics and chemical compatibility arise."

Jan 1, 1994

By Y. C. Avniel, T. E. Warner

"It is important to be able to measure sulphur and nitrogen in molten iron and steel on-line. Unfortunately, there are no solid electrolytes which are stable under oxidising conditions and in which the ions of these species are mobile. In this paper, novel applications of beta alumina electrolytes are described and the results compared with data in the literature. Excellent agreement was obtained confirming this approach as a viable method of detecting elements whose ions are not mobile in solid electrolytes.IntroductionIn the past two decades, the rate of many processes in steelmaking have increased substantially. The sophistication of chemical analysis has also increased but analytical equipment is frequently positioned a significant distance from the operating plant which dictates that time is spent taking a sample, sending it to the analytical facility, preparation of the analytical sample prior to insertion into the equipment. In many cases, the time taken for analysis can exceed the time taken for the actual process and is now the rate defining step. Furthermore, most analytical methods are unable to distinguish between the amount of element which is dissolved in the steel and that contained in precipitates. Even if the analytical equipment could separate these two, the distribution would have changed between the molten steel and the cast sample. It would be an advantage to analyse on-line for impurities in molten metals."

Jan 1, 1997

By Y. Houbaert, L. Kestens, R. Decocker

"A magneto-elastic model is presented to calculate the orientation dependence of the magnetostrictive strain, observed at saturated magnetisation in ferromagnetic materials with a cubic crystal structure and an arbitrary crystallographic texture. The formula of Becker and Doring is used to express the anisotropy of magnetostriction for a single crystal. In order to simulate the macroscopic average magnetostriction of a polycrystalline aggregate (with an arbitrary texture) the Reuss assumption of the elasticity theory was applied. According to this assumption the various orientations of the polycrystal can defonn without constraints, producing local strain incompatibilities in the microstructure but observing total stress equilibrium. The macroscopic strain is calculated as the weighted average of the individual strains of all orientations composing the polycrystal. The weight factors are determined by the volume fractions of the corresponding orientations of the given texture, which can be measured by standard X-ray diffraction techniques. The model is applied to simulate the variation of magnetostriction (at saturation) with respect to the rolling direction for a standard grade of Goss-oriented electrical steel. A brief comparison with experimental data allows validating the basic model assumptions. IntroductionBecause of tougher environmental constraints, the noise reduction in transformer cores has become increasingly important. It is generally accepted that the main source of noise is magnetostriction, which is known to be caused during the magnetisation process by the movement of 90° magnetic domain walls and the rotation of the magnetisation vector out of the easy directions. Therefore, it is obvious that when a ferromagnetic body is magnetised to saturation, the resulting magnetostriction will be dependent on the distribution of magnetic domains in the initial state.In the literature two coefficients are used to describe the resulting magnetostriction at a saturating magnetic field. The total strain, measured from an arbitrary demagnetised state to technical saturation, is called the saturation magnetostriction, and is denoted by (~)s. The tenn magnetostriction coefficient will be employed to designate the strain measured from the ideal demagnetised state (i.e. one in which no preferred orientation of domains exists) to technical saturation. Failure to recognise the difference between these two quantities has led to considerable confusion in the literature.The magnetostriction coefficient for a single crystal is a well-known property for ferromagnetic cubic materials. In 1939 Becker and Doring [1] have derived the following relation, describing the magnetostriction coefficient for single crystals with a cubic symmetry:"

Jan 1, 2001

By S. -H. Jeon, Y. -S. Choi

"The three dimensional current distribution on the rectangular cathode is predicted using a boundary element method with a linear element of trigonal type. The effect of cell geometry and anode shape on current distribution is simulated. Calculated results compare well with experimental results. The proper combination of anode size and distance between electrodes increase the current uniformity.The importance of electrodeposition as a fabrication technology in the electronics industry is large and growing. The main advantages of this wet processing method, in comparison to other dry processing methods, lie in its high yield, rapid processing and low cost. In nearly every application of electrodeposition the pursuit of deposit uniformity, especially thickness uniformity, has been technically imperative. The thickness uniformity of the deposit depends largely on the current distribution over the cathode. The current distribution is primarily determined by the geometrical characteristics of the electrodes and the cell. Also the polarization at the electrode surface and the mass transfer affect the current distribution.The current distribution is an important consideration for those involved in designing electrochemical systems and electroplating systems in particular. Although it is important, the common practice in industry is to use trial and error method to design the cell that optimize the uniformity of current distributions in electroplating. The purpose of this paper is to illustrate the useof boundary element method to predict three-dimensional current distribution in rectangular cell.The calculation of the current distribution is possible by various numerical techniques, which include the finite difference method (FDM)1, the finite element method (FEM)2, and the boundary element method (BEM)3,4. These methods of the numerical calculation have various problems, respectively, but the BEM is considered to be the most efficient. This is due to the fact that the BEM has the advantage of solving field equations only on the surface of a calculation domain. A good comparison between the BEM and the FEM for the secondary current distribution in a Hull cell was made by Matlosz et al.5The fundamentals on the theory of current distribution in electroplating are well-established in the literature by a number of authors.6, 7, 8 However, a small fraction of these works have been specially addressed to three-dimensional analysis, and, mostly thel·10 have focused on the problem qualitatively rather than quantitatively.Extending the previous work to three-dimension, we developed the program for the quantitative calculation of 3-dimensional current distribution using a boundary element method with a linear element of trigonal type. Integrals with singularity from the fundamental solution have been analytically computed and it is shown in detail in the Iiterature11. This paper deals with the three dimensional current distribution for the electrode position of copper in a cubic type cell and the effect of anode shape, size and the distance between electrodes on current distribution is studied."

Jan 1, 1997

By Mingchun Lu, Zhe Wang, Mingming Cao, Xiangdong Xing, Shan Ren, Jianliang Zhang, Zhengjian Liu

"The effect of reduction temperature on the vanadium titano-magnetite carbon composite pellets was investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM), and the discussion has put emphasis upon the enhanced reduction mechanism of additives containing CaF2 and NaF in this paper. The results showed that the reduction temperature of 1350°C was needed for the generation, mergence and growing up of metallic iron as well as monomer dissociation between metallic iron particles and slag phase in the vanadium titano-magnetite metallization pellets. The iron compound was completely reduced into metal iron, and Fe2Ti04 was mainly transformed into metal iron, (Fe,Mg)Ti205 and FeTi03 at 1350°C. The maximum metallization ratio was only 88.5% at 13500 for 30 min without any additive. However, with the addition of 3.0% CaF2 or NaF, the metallization degree of pellets could reach up to 94.8% and 92.5%, respectively.IntroductionVanadium titano-magnetite which is mainly distributed in the area of Panxi, Chengde and Maanshan in China is a kind of complex iron ore which contains various valuable metal elements such as iron, vanadium, titanium, etc. Among the above areas, Panzhihua (Sichuan Province in China) area possesses the largest deposits of vanadium titano-magnetite and the future reserves are more than 100x108t, and the reserves of Ti existing as Ti02 reach to 8.7x108t which occupy over 91% of the whole nation and ranked No.1 in the world[1]. Lots of researches on the comprehensive utilization of vanadium titano-magnetite have been conducted in the world. And many technological processes have been applied successfully in industrial production. Among these processes, the process of rotary kiln-electric furnace is employed to recover iron and vanadium in South-Africa, while the process of blast furnace-rotary furnace is widely used in Russia and China. Besides, many researchers have made efforts on employing new direct reduction process to realize the effective comprehensive utilization of vanadium titano-magnetite[2-4]. However, the direct reduction process is only researched in laboratory and it has not been used in industry."

Jan 1, 2013

By K. A. Brunk

Newmont&apos;s research, operations, history and experience with pre-treatment of preg-robbing carbonaceous ores are described, with emphasis on the chemistry, physics and kinetics of chlorine treatment. Present operations, control strategy and projected changes are also described, including a summary of the adsorption of chlorine into pulps and off-gas scrubbing. Conditions of chlorination have been optimized by the use of Eh-pH diagrams of the gold-chlorine-water system, and have resulted in significant increases in gold recoveries and decreases in chlorine consumptions.

Jan 1, 1987

By Yuanpei LAN, Minren XU, Deliang NIU, Zhu WANG, Qingcai Liu, Shan Ren

Removal of gas is the major function of RH degasser. To optimize the RH refining craft in Chongqing Iron and Steel Co. Ltd, the degassing effect of RH degasser at different degrees of vacuum was investigated using a vacuum induction furnace. In addition, the effect of processing time on the gas content dissolved in molten steel was also studied. The results showed that degree of vacuum was one of the important factors that determined the degassing efficiency in RH refining process. High vacuum degree is helpful in the removal of gas, especially in the removal of [H] dissolved in molten steel. The processing time could be reduced from 25-30 min to 15 minutes and gas content could also meet the demand of RH refining

Jan 1, 2015

By M. Tokumasu, T. Mutoh, Y. Sugawara

"In October 1986, a process computer was introduced in order to achieve an optimum combustion of pulverized coal at the reverberatory furnaces. The secondary combustion air volume is controlled based on the nitrogen oxide concentration of the off-gas from the reverberatory furnaces. The carbon monoxide concentration has strong relation with the concentration of nitrogen oxide under the situation of using alternative fuels, such as chipped tires and p,ulverized coal. Using this computer aided combustion control system, both nitrogen oxide and carbon monoxide concentrations were stabilized and conventional monitoring and controlling apparatuses were absorbed into this computer system. Due to this easily operated system, labor cost was reduced and the operation of the reverberatory furnaces and the off-gas treatment plant became stable.IntroductionOnahama Smelter and Refinery started its operation in April 1965 as a large scale copper smelter and refinery in Japan. The green charged reverberatory furnaces were introduced and bunker C oil was chosen as the fuel for the reverberatory furnaces. After the oil crises, Onahama was forced to use cheaper fuels such as coal and waste tires, i.e., alternative fuels instead of the expensive oil. As the amount of the alternative fuels fed to the reverberatory furnaces increased, the concentrations of nitrogen oxide and carbon monoxide in the off-gas became unstable. Consequently, the fluctuation of the combustion condition became not to be negligible in view point of a combustion efficiency and pollution regulations. A process computer has been introduced to overcome these off-gas troubles and to reduce the operating cost of the smelter.Outline of Operation HistoryInitially, the operation started by one reverberatory furnace and then the capacity was expanded almost twice by additional furnace in December 1972. As shown in Figure I, the smelting throughput was depressed after oil crises in 1973 and 1978. From 1983 to 1985, some copper mines stopped their operations because of low price of copper metal. During this period, Onahama suffered from the shortage of concentrate production levels were depressed."

Jan 1, 1989

By B. Wasmund, K. Adham, K. O'Keefe, C. Lee

"Metal chlorides (e.g. iron and nickel) can be pyrohydrolysed at elevated temperatures to yield an HCl rich off-gas and a metal oxide product. Typically, the high energy requirement for pyrohydrolysis is provided by the combustion of a hydrocarbon fuel with air. Here, it is demonstrated that the use of oxygen-enriched combustion can result in lower fuel requirements and higher HCl concentrations. In addition, the oxygen enrichment can result in a smaller volume of off-gas and thus, smaller and less expensive process equipment. This new concept can be applied to both the spray roaster (SR) and the fluidized bed reactor (FBR). Similar to the aircombustion case, the oxygen-enriched process can use a direct contact venturi scrubber, to recover energy from the roaster off gas, but at a higher efficiency. The new process also uses an absorption tower for capturing HCl from the roaster off-gas, but generates a stronger HCl solution than is possible with pyrohydrolysis in air.BackgroundIn recent years, the metallurgical industry has become increasingly involved with developing methods for extracting metals, upgrading products or cleaning metallic products by using hydrochloric acid. These applications of chloride metallurgy often result in metal chloride solutions, which should be processed to regenerate HCl for reuse, and to recover the metal value as a product or by-product oxide [2, 3, 4].The pyrohydrolysis of metal chloride solutions has been done in two types of air roasters: spray and fluidized bed. The existing roasters burn a hydrocarbon fuel in air, to provide the required energy for evaporating the feed solution and to provide an elevated temperature for the chloride pyrohydrolysis to occur, according to the following reactions:"

Jan 1, 2011

By M. Wu, A. Kharicha, A. Ludwig

"The droplet formation during melting of a 400 mm diameter electrode is simulated with a multiphase-MHD approach. The computational model includes a layer of slag and a layer of liquid steel. A VOF approach is used for the interface tracking and a potential formulation is used for the electric and the magnetic field. The Lorentz force and the Joule heating are recalculated at each time step in function of the phase distribution. The first results provided by this model are presented.IntroductionThe Electro-Slag-Remelting (ESR) process is an advanced technology for the production of components of e.g. high quality steels [ 1-9]. An alternating current (Figure 1) is passed from a conventionally melted and cast solid electrode through a layer of molten slag to the baseplate. Because of the electrical resistivity of the slag, Joule heating is generated and the slag transfers this energy to ingot and mould surfaces and to the melting electrode tip. The molten metal produced in the form of droplets passes through the slag and feeds a liquid pool from where directional solidification takes place. The slag and the ingot are contained in a water cooled copper mould. As also the baseplate is water cooled, a heat flow regime is imposed that gives controlled solidification, and this results in improved structure characteristics of ESR ingots.This process involves two liquids, a liquid metal and a liquid slag. Each liquid is subject to a phase change due to melting and/or solidification. From a fluid dynamic point of view, the ESR process is clearly a multiphase process, with free interfaces (slag/pool, gas/slag), and with a mixed area (slag and falling steel droplets) [ 10-15].Physically, the development of the heat and mass transfer at the slag/droplet interface is important for the final ingot quality, composition and cleanliness. Visual observations of the droplet formation just under the electrode being melted is almost impossible. Due to the presence of high temperatures, opacity of the materials, and the presence of the mould it is not possible to directly observe the behaviour the slag/pool interface. Although usually assumed flat [1-9], a previous work [10] using a Volume of fluid (VOF) model has shown that the interface shape between a layer of slag and steel layer in a cylindrical cavity is highly coupled with the distribution of the electric current. A full scale simulation of the ESR process using a VOF model has shown that the shape of the pool interface is likely to be non flat."

Jan 1, 2011

By Fjeldstad Karin Jusnes

Two quartz types used in the silicon and ferrosilicon industry were heated to temperatures of 1600 and 1700 °C. The parameters varied were the temperature and the holding time at maximum temperature. The amount of quartz, cristobalite and intermediate amorphous phase were measured using XRD and the internal standard method. Type P showed a much larger ability to transform to cristobalite at lower temperatures than type A. Type P had a larger amount of alkali and alkaline earth impurities. This could have enhanced the transformation to cristobalite. For quartz type A the amount of cristobalite was larger at 1600 °C than 1700 °C. This can also be seen for some of the samples of type P at shorter holding times.

By Muhamad Firdaus

There is a growing interest in Magnetoelectric (ME) materials in view of both fundamental understanding and novel desirable applications. The application potential for multiferroic materials with the possibility of reversing the magnetization by applying an electric field (or vice versa) is quite promising especially in data storage application. The rare earth ortho-ferrites (REFeO3), such as NdFeO3, have been studied extensively in recent study in the context of discovery of magneto-electric (ME)/multiferroic nature materials. In this paper a potential high temperature recovery of rare earth elements in the form of REFeO3 from waste permanent magnets using direct oxidation in air was investigated. It was found that REFeO3 (NdFeO3) phase can be separated from the other oxide phases by thermal treatment of NdFeB magnet waste at 1100 °C in air atmosphere. The REFeO3 also found to have different physical characteristic (density) from the other layers and can be separated physically. This paper will include a proposed flowsheet to recover Nd as NdFeO3 through powder separation. The technique can be beneficial and favourable for RE recycling and recovery from waste permanent magnets.