Search Documents

By Alan Campoli

Approximately 100 million fully grouted rebar roof bolts are installed each year in the United States, 80% are B-Series (5/8 inch fully grouted rebar in a one-inch borehole). The lesser used more expensive A-Series (3/4-inch fully grouted rebar in a one-inch borehole) maximizes resin performance. Standard B-Series provides only 60% of the pull out resistance of A-Series. The Eclipse System was developed by Minova USA Inc. and marketed with Excel Mining Systems to improve the performance of B-Series. A 1/8-inch offset bolt head combined with a specially formulated Eclipse Lokset resin cartridge results in increased mixing efficiency and more uniform resin anchorage. Over two million units have been sold to date; the majority of these Eclipse bolts have been sold to coal mines in the Illinois Basin. Pull testing has demonstrated that a Grade 60 Eclipse bolt provides equal or superior pullout resistance as compared to a Grade 40 No. 6 rebar. Short encapsulation pull tests have yet to consistently demonstrate the superior pullout strength of Eclipse to standard B-Series, however 12 inch Eclipse grouted columns have successfully held in excess of the bolt yield load. The successful substitution of Eclipse bolts for A-Series has significantly reduced the primary roof support costs by approximately $0.18 per foot of bolt. Recent over coring analysis of various anti-gloving methodologies performed in New Zealand has confirmed the superior mixing of the Eclipse system (5).

Jan 1, 2004

By John C. Stankus

In this paper, an innovative concept in longwall tailgate support is discussed. This new concept utilizes a new high capacity roof truss system in lieu of conventional wooden crib block. The first field test was conducted at Bailey Mine and was very successful. Similar tests have been installed in other mines and seams. An extensive instrumentation plan was designed and implemented in the truss test area. The test data has shown that the dynamic roof truss system effectively controls the various abutment pressures caused by longwall mining thus maintaining a stable tailgate entry.

Jan 1, 1994

By Peter Griesenbrock

In German underground coal mining mostly arch and some rectangular roadways are used in the development work. Due to its positive results from numerical and physical modeling techniques as well as good underground experiences, the numbers of rectangular roadways has increased significantly. Today the bolt support - independent of its cross-sectional shape - represents an undeniable support element. During the introduction of new bolt techniques a detailed investigation of the rock and support mechanical effectiveness of bolt support in roadways at all operation stages is of basic importance. This effectiveness can be predicted and verified using different simulation techniques. For the planning of rockbolted roadways two supplementary simulation techniques are presented in this paper. By combination of all available planning tools the best result for planning assurance can be achieved. Keywords: numerical modeling, physical modeling, arched roadway, rectangular roadway, roofbolting, advancing longwall.

Jan 1, 2002

By Olayemi Akinkugbe

As coal production in the United States continues to increase, the availability of unexploited or virgin fields continue to diminish. As a result, mine operators are forced to mine in unfavorable or multiple seam conditions. The safe, productive exploitation of coal in multiple-scam conditions requires specific design technology. At present, there are two general design approaches that the mining engineer can use to analyze the multiple-seam problem in question, either simple empirical relationships or complex numerical models. Often, the empirical approaches are too general for the specific problem and the numerical models require too much time and expertise for the practicing engineer. This paper introduces a new computer program, Lam2D, designed specifically to enhance multiple seam mining operation by quickly and easily calculating, stress, displacement, subsidence, horizontal strain and safety factors associated with multiple seam mining situations. The program implements a simplified, two-dimensional boundary-element method in order to model the complex multiple-seam stress and displacement interactions. Most importantly, the program is greatly simplified by incorporating automatic overburden, interburden, coal and gob property generation thereby reducing typical modeling and solution time to a few minutes.

Jan 1, 2004

By Lorraine Kent

Comparison of in-situ stress overcore measurement results with those determined from laboratory evaluation of Acoustic Emission (AE) testing on oriented sub-core samples has been carried out for a variety of mining environments. These include UK and German Coal mines at moderate depth, shallow-level South African Coal mines and deep-level South African gold mines. Results show that the `Kaiser Effect' or 'Stress Memory-Damage is readily determinable throughout the brittle deformation process, although particular care is required in interpretation of results during the 'bedding-in' phase of testing and the region associated with unstable crack growth prior to failure. The results suggest that AE provides a useful complimentary method for comparison with existing methods of stress determination. The success of the method can, however, be dependent on both rock type and the likely magnitude of in-situ stress in comparison to the strength of the rock. Keywords: in-situ stress, acoustic emission, Kaiser Effect

Jan 1, 2002

By Eric R. Bauer

Skin failures of roof and rib in underground coal mines continue to be a significant safety hazard for mine workers. Skin failures do not usually involve failure of the support systems but result from rock or coal spalling from between the support elements. For instance in 1997, over 800 miners were injured by roof and rib falls, of which 98 pet were the result of skin failures. Also, nearly 80 pct of the roof and rib failure injuries occurred at or near the working faces in development sections. The face area is a zone where the potential for skin failure accidents and injuries and roof and rib failures, in general, is high because of mining activity, ground readjustment due to changing stress conditions, and the higher exposure of mine workers. In addition, failures occur where the roof and rib are unsupported. This paper features a review of the roof and rib accident statistics resulting from skin failure, highlighting the incidences by average days lost, in-mine location, state, MSHA District, and worker activity at the time of injury. A detailed analysis of recent fatalities caused by skin failure is included. Also discussed are the causes of roof and rib skin failures, current methods and support materials for skin surface control, as well as a historical literature review of skin failures and control methods.

Jan 1, 1999

The purpose and current practice of cable trusses in underground coal mines is briefly outlined and details of various cable truss designs are presented. The main part of the paper describes the in-situ performance of cable trusses installed as secondary supports in gateroads and recovery roads of longwall coalfaces. The performance analysis is based on the results of in-situ monitoring carried out at a number of sites at two underground coal mines within Australia. Truss performance has been assessed as load developed in relation to roof convergence, face position and time. Additionally, the influence of strata conditions, installation pattern/density, roadway layout and geometry have been taken into account. An analytical model has been developed to predict truss loads. The principal variables are listed and the basis of the model is described. Based upon behaviour observed in the field the model has been progressively upgraded and validated against measured performance. Guidelines on truss performance and factors which influence it are presented and the implications of these to the use of cable trusses is discussed. Possible methods for improving truss performance in certain strata conditions are outlined and some comments are made on the value of cable trussing compared to cable bolting in these situations,

Jan 1, 1992

By Stephen C. Tadolini

A new innovation in coal mine roof support has been developed by the Bureau of Mines at the Denver Research Center. The technique, called "Thrust Bolting,"1 converts a traditional passive roof support system, a full or partial column rebar bolt, into an active support system by following a specific installation process. The thrust bolting system provides two advantages from a ground control standpoint. First, because the system is active, no roof movement is necessary to put the bolt into tension. This eliminates the possibility of strata separations in sedimentary roots, minimizing progressive-type roof failures. Secondly, the tension placed on the system is independent of mechanical devices or torques. This eliminates the highly variable frictional losses that occur between the bearing plate and the bolt head and in the threaded portions of traditional active support systems. These two improvements create a safer working environment for mining personnel. An additional advantage of this improved support system is the reduced cost of installation and maintenance. The initial support cost is reduced by a minimum of 30 percent per bolt when compared to similar conventional support systems. The labor intensive and potentially hazardous torque¬tension test, required for most tensionable active support systems, is not required for thrust bolts. The potential for improved support performance and cost reduction of thrust bolting has generated a considerable amount of interest from both industry and MSHA. This paper will describe, in detail, the theory and application of thrust bolting and present the results of two underground coal mine case studies.

Jan 1, 1990

By Brian Clifford

Thoresby Colliery is in the process of recovering an old roadway that was flooded following the closure of an adjacent mine. The aim is to re-use the roadway as a gate road for a longwall retreat panel and it is therefore important to establish the condition of the existing rockbolt support during the recovery operation. Two NDT methods, ultrasonics and RMT's newly developed RF (Radio Frequency) system were used in combination to interrogate the rockbolts to determine their condition. This paper describes the condition of the rockbolt supports, the NDT methods used and the problems that had to be overcome to successfully apply the two methods.

Jan 1, 2002

By Syd Peng

It is necessary to fully understand roof geological features in order to design a proper roof support system for underground coal mines. These geological features include: rock type, rock strength. rock layer interfaces, voids, cracks, and bed separations. Traditionally, engineers have relied heavily on the use of surface borehole log data to identify geological features. Since surface boreholes very expensive to be drilled in close spacing, log data are often insufficient to provide detailed information on the roof geology. Recent advances in control technology have made a large amount of roof bolter drilling data available to mine personnel. These data can be obtained during normal roof bolt installation cycle with little or no interruption in mining operations. This research project has developed several methods to identify geological features in a mine roof from measured drilling parameters. Power trend line analysis can be used to locate discontinuities and interfaces in mine roof. Power averaging can be applied to determine the relative strength of roof strata. Thrust trend line analysis can be used to locate fractures in mine roof. The results of these methods are combined to produce a mapped roof geology In a production environment, manually interpreting and managing collected drilling parameters is not practical since hundreds of holes will be drilled during a production day. A new software package, MRGIS, has been developed to allow mine engineers to make use of the large amount of roof drilling parameters for roof support design. An actual underground test site is presented to demonstrate the analysis and display capabilities of MRGIS.

Jan 1, 2003

By Zuoliang Xiu

Experience indicates that rockbolting is the most efficient and cost effective means of supporting gateroads of retreating longwalls. However, gateroads supported solely by rockboltiug currently accounts for less than 16% of the 4500km of annual gatemad drivage in China According to a stated target of the Ministry of Coal Industry, this percentage should be at least 50% by the year 2000. Since the learning stage of the technology which is indicated by low drivage rates and frequent roof falls in rockbolted gateroads must be overcome , strategies for the application of rockbolting to gateroads have become the focus of discussions on this topic. This pap presents the recent development on longwall gateroad rockbolting technology in China The development work has concentrated on understanding the mechanism of rockbolting; establishing new design procedures of bolting parameters fix gateroad support upgrading the consumable; optimizing bolt installation procedures; adopting better roofbolting machines; and developing adequate secondary reinforcement technique. The authors believe that this development work together with the on-going wok in other aspects of gaterosd rockbolting, as discussed in this paper 9 represent the rational strategies for the application of rockbolting technology to a wider range of longwall gateroads in Chinese d mines .

Jan 1, 1997

By Asmaa Yassien

Finite element models were developed to study the effect of tensioned and fully-grouted bolts on the stability of the mine opening in a three-entry development system using a typical geological column for the Pittsburgh Coal Seam. The models were used to study the effect of each bolt type on the stress distribution in the immediate roof, yield zone development and the vertical deformations. Comparison of all of those features show that the effect of a tensioned bolt on the stress distribution in the immediate roof is restricted to limited areas, whereas the fully-grouted bolt has a much wider effect on the stress distribution. Both types of bolts can reduce the yielding and deformation in the immediate roof to different degrees. The fully-grouted bolt reduces the sliding along the bedding plane more than the tensioned bolt. Both types of bolts were able to maintain the bedding planes without separation. The induced forces in both types of bolts are analyzed. A rapid increase in the shear force and bending moment occurred in the fully¬grouted bolt due to the relative motion of bedding planes.

Jan 1, 2002

By Michael Gauna

In 2010, the number of fatal rib falls in U.S. underground coal mines exceeded fatal roof falls for the first time ever. While recent trends have seen roof fall fatalities reduced by about 62% since the 1990s (from an average of 9.6 per year in the 1990s to 3.6 per year during the last five years), the incidence of rib fall fatalities has remained approximately constant (about 1.5 per year). In addition, injury incidents associated with pillar rib failure have been steady at approximately 100 per year. The persistence of rib fall injuries, underlined by the recent increase in rib fall fatalities, has led to this investigation of the coal rib failure parameters and methods available to mitigate rib failure in U.S. underground coal mines A detailed study of the 21 fatal rib fall incidents that have occurred since 1995 (excluding coal burst incidents) indicates that the two most important risk factors are the mining height and the depth of cover. The depth of cover was 700 ft (213 m) or greater in 81% of the fatalities, and the mining height was at or exceeded 7 ft (2 m) in every instance but one. Other risk factors included multiple seam interactions, rock partings in the seam, and retreat mining. The accident history reveals that joints or slickenside features within the rib increase the hazard. Approximately threequarters of the rib fatality victims were roof bolting machine operators and continuous mining machine operators. This paper includes a brief overview of techniques for rib control; including bolts, standing support, bent steel straps, and rib strapping. The available mining equipment features for installing rib support and protecting operators from rib falls are also discussed. A proactive approach to rib control using available technologies will lower the risk to miners and is an endeavor that must be pursued to reduce rib fall accidents.

Jan 1, 2011

By Paul Cartwright

A rockbolted roadway risk assessment procedure has been developed specifically for the Parkgate seam at Thoresby Colliery by Rock Mechanics Technology and colliery engineers. The purpose of this assessment is to identify any areas of significant risk in relation to roof instability due to potential failure or overloading of the rockbolt support system. This allows appropriate additional support to be installed in sections of roadway considered to be at increased risk. The assessment of risk in rockbolted coal mine roadways, in terms of fall of material, has to be based on an understanding of the rock mass behaviour at that site. The development of an appropriate risk assessment system is therefore site specific. A consistent approach to developing such a system can, however, be applied by adopting the same general logic to each individual site. The use of risk assessment to categorise areas with increased risk of roof instability has been undertaken for four longwall panels at Thoresby. The procedures used for these assessments are discussed and the operational benefits examined. The approach successfully used at Thoresby has been developed into a routine tool to assist mine personnel in assessing areas of potential roof instability in rockbolted roadways and as a means of communicating the position of these areas to both supervisors and workmen. The system provides a rational and objective interpretation of the current underground conditions based upon a logical, consistent and structured approach.

Jan 1, 1999

By Hamid Maleki

This study presents a historic overview of the role of mobile roof support (MRS) technologies in improving stability and worker safety and presents the results of recent field evaluations of the MRS load rate monitoring device and other remote deformation-monitoring techniques. Field studies were implemented at two sites in cooperation among researchers from the National Institute for Occupational Safety and Health (NIOSH), Maleki Technologies, Inc., and J. H. Fletcher & Co. The objective of the field programs were to (l) study the interaction between MRS's and coal mine strata and (2) develop and test suitable monitoring systems for assessing roof and pillar stability. An MRS consists of a roof canopy, four hydraulic cylinders, a caving shield canopy, and associated electromechanical systems mounted on crawler tracks. The machines are controlled by radio from a remote location and operate on self-contained power units. Typically, MRS's have capacities of 5,340 and 7,120 kN (600 and 800 tons). In comparison to posts, an MRS is capable of maintaining the yield load after significant amounts of roof-floor deformation. Because the mining cycle is accelerated, MRS's help reduce the potential for time-dependent roof falls. MRS performance has been monitored in the laboratory under controlled static loading conditions and in the field under deep, two-scam mining conditions. Laboratory studies have quantified support capacity and system stiffness as a function of machine height. Field investigations have focused on determination of optimum operating conditions and development of warning systems that indicate excessive load on the machine and/or impending roof-pillar stability problems. Analyses of field data show that roof instabilities are influenced by (1) pillar failure, (2) pillar yielding, (3) mine seismicity, (4) geologic structures, and (5) panel layout designs and mining practice. Pillar yielding and failure (unloading) and seismicity can be conveniently monitored by the load rate monitoring device, but for consistent detection of roof falls, additional deformation measurements directly within the cuts ate needed.

Jan 1, 2001

By Stephen C. Tadolini

The U.S. Bureau of Mines (USBM) is conducting research to provide alternatives for traditional secondary support methods. These cost-saving methods are proving to afford safer installation, improve entry stability, eradicate material-handling injuries associated with crib supports, and enhance ventilation. In cooperation with Mountain Coal Company, the USBM replaced timber cribbing with high- strength cable supports to provide stability in a gate road that was used for two longwall panels. The support design consisted of 2.1-m (7-ft) full-column resin-grouted bolts and 4.8-m- (16-ft-) long high-strength resin-grouted cable supports. Three support concepts were evaluated: passive, stiff, and tensioned systems. Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during panel extraction. The stress and loading histories for both panels and the abutment and yield pillars were monitored to assist in evaluating the stress transfer and pillar performance in conjunction with the roof behavior. The test results indicated that resin- grouted cable support systems successfully maintained the immediate and main roofs during the extraction of two longwall panels. This paper describes the theory, application, and advantages of resin-grouted cable supports and presents the mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1994

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP), Version 1.0, was released at the 19th Gmund Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (I) including uncontrolled convergence into the design requirements for standing roof supports, (21 the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capabilily to define ground reaction curves through convergence measurements alone wthout having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (I) additional graphics capabilities to facilitate rapid assessment of support comparisons. (2) an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and measure of roof coverage for the design layout of the support system These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions whlch could not be fully analyzed in the original version of the program.

Jan 1, 2001

By M. Ashraf Mahtab

A feature of interest in stability of excavations in domal salt is the phenomenon of gas outbursts which has occurred in five of the six mines in Louisiana salt domes. Gas outbursts are sudden erruptions of salt and gas from the face or roof of a mine opening. They are associated with anomalous zones in salt, depth of mining, and the method of excavation. Potential risks from gas outbursts include an unplanned connection to a reservoir of water or hydrocarbons and, possibly, a loss of the mine. It is proposed that a gas outburst is initiated by disking in biaxial compression and propagates by spalling of the cavity walls and further disking. The outburst is terminated by a combination of dilatancy hardening, increase in stress along the cavity axis, and enlargement of the cavity to the boundaries of the pressure pocket. Identification of burst- prone areas will require research into in situ measurement of material characteristics and further under- standing of the mechanism of gas outbursts. Shock blasting in advance of mining appears to be a promising technique for controlling gas outbursts.

Jan 1, 1981

By Thomas Barczak

Longwall shields provide essential ground control in Iongwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of¬the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (I ) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield's capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

Jan 1, 2002

By Lorraine Kent

Excessive floor and side deformation are major problems in deep coal mine entries in Europe, and in particular in the UK where rockbolt support is used at depths of working of around 3000 ft. This has major economic and safety implications for the industry resulting in the potential for sidewall instability, disruption to mine infrastructure, (belt conveyors, floor mounted transport systems and powered supports), and the requirement to safely manage excavation of large quantities of floor material. European research aimed at improving deformation control is described. The outcomes include innovations in support systems, materials and installation practices, as well as better methods for predicting and monitoring deformation levels. As coal mines get deeper, some entry deformation is inevitable, and methods for mechanised removal of floor lift and repair of sidewalls have been developed to allow production to continue as mining clearances are re-established.

Jan 1, 2014