Search Documents

By A. D. Davis, G. A. Zabolotney

A ground-water flow model was developed to simulate the postmining recharge rate from precipitation at the Belle Ayr surface coal mine, which is located in the Powder River Basin near Gillette, WY Wyoming state regulations require that reclaimed lands should provide a rate of recharge that approximates the premining rate. Steady-state calibration and transient simulations showed that the postmining recharge rate through spoil is at least 50 mm (2 in.) per year, exceeding the original infiltration rate of 4 mm (0.16 in.) per year to shallow overburden aquifers. Major reasons for the increase include the flat topography of the reclaimed areas and the decreased spoil density. It is expected that the backfill will disaggregate and settle over time, eventually resulting in a nearly constant recharge rate that is less than 50 mm (2 in.) per year but still somewhat greater than the premining rate.

Jan 1, 1997

By Malcolm J. McPherson

This paper describes the algorithm used in a BASIC program for an IBMXT microcomputer, to simulate the underground mine climate. The program called CLIMSIM has been developed and refined over several years as a result of considerable use at operating mines. The program has been designed to be easy to use and be understood by the practicing mine ventilation engineer. It provides predictions of the work place climate, so that the optimum ventilation/cooling system can be designed to obtain a certain air cooling power or effective temperature at the work place. An example is given of the application of the program to a mechanized cut and fill stope at the Homestake gold mine in South Dakota.

Jan 1, 1986

By R. Harris, M. Misra

Column flotation technology has a demonstrated potential for recovering clean coal from high-ash waste fines. The effect of different variables such as air flow rate, frother addition, depressant addition, percent solids and particle size on the quality of separation are discussed. Results indicate that air flow rate and depressant addition are the important variables which control the selectivity in the flotation of fine coal in a column cell. Separation efficiency achieved with column cells is significantly better than that with conventional flotation cells. Under appropriate experimental conditions with a deep column, more than 80 percent coal can be recovered in the concentrate containing 10 percent ash from waste fines containing over 60 percent ash.

Jan 1, 1988

By D. R. East

Recent experiences within certain sectors of the international mining industry suggest an underestimation of the environmental risks associated with the design of mine waste-management facilities. These experiences show that the technical and managerial challenges of responsible mine waste management is not always fully appreciated. Unfortunately, the image of the mining industry's environmental performance is negatively impacted by a relatively few number of failures. This negative view overrides the many positive contributions made by the majority of mining companies. The fact that these failures continue to occur in developed and developing countries is indeed re¬markable and indicates a degree of risk-taking approaching unacceptable levels. The design requirements for tailings storage facilities are, in many cases, more demanding than those of conventional water dams because seepage of fluids that contain dissolved metals may pose a greater threat than the mere loss of water.

Jan 1, 2000

By Stephen G. Whittaker, Rosalind A. Schoof, Martha J. Steele

In determining remedial action objectives for metals in soils, the U.S. Environmental Protection Agency typically assumes that the metal concentrations in house dust are the same as the metal concentrations in soil. Data now available from several studies that were conducted in mining communities suggest that for some metals, concentrations in house dust may be lower than those in soil. This paper reviews available data on the relative soil and indoor dust concentrations of arsenic and cadmium and examines how changing assumptions regarding indoor dust concentrations of arsenic affects risk assessments and determination of cleanup levels.

Jan 1, 1992

By L. S. Leal Filho, L. A. F. Barros, S. M. Assis

Zeta potential determinations and microflotation tests (with starch, sodium oleate and flotigan EDA-B) versus pH, pCa and pMg were performed with apatite and typical silicate minerals that occur in Brazilian phosphate ores: schorlomite, diopside, quartz and micas. Unlike quartz and micas, schorlomite and diopside were depressed by cornstarch during anionic flotation with sodium oleate (pH 1 9). The selectivity of the separation apatite/quartz and apatite/micas by flotation with sodium oleate was adversely affected by the presence of calcium (pCa) and magnesium (pMg) in flotation pulp. Solubility/cation exchange capacity of micas is an important source of dissolved calcium and magnesium in the system.

Jan 1, 2002

By Wojciech Suwala

The transition from centrally planned to market economy affects methods of economic analysis. The models which were used in the past are riot valid presently, however they we're the seed which initialized the development of methods and applications. There is more than twenty years of experience in modeling of coal mining development. The first attempts were devoted to select the moment of mine construction commencement in order to meet planned output. In Poland significant development of such models began in 1986. Within the Central Research and Development Program there has been a continuous development of models. These models from econometric to optimization ones, were a certain sequence which, in accordance with changing economy system, led to the last version of the model. It is the most suitable one for contemporary problems of coal mining in present Polish circumstances.

Jan 1, 1992

The purpose of this paper is to describe two systems designed to provide estimations in stratigraphic orebodies for the purposes of detailed mine planning. The first is a completely geostatistical approach and the second is a combined geostatistical/deterministic approach. The essential features of both systems are the estimation of stratigraphic ore boundaries and the subsequent use of those boundaries to provide stratigraphic (or zonal) control for block and point grade estimation (kriging). Both systems are illustrated by application to a section of, the Hilton orebodies, Queensland, Australia.

Jan 1, 1989

By Mark E. White, John H. McCowan, Michael C. Costello

Minproc Engineers has carried out the design construction and commissioning of thirty two process plants in the period 1978-87. Twenty eight are gold silver recovery plants, and of these twenty two were gold alone and six were gold and silver. In most plants carbon was used for gold adsorption. Desorption has been carried out using the USBM Homestake method, the Anglo American Research Laboratories method, and the Micron Methanol method. Electrowinning has utilised steel wool, stainless steel wool, and aluminium cathodes. Electrorefining using polished stainless steel cathodes is practised. This paper summarises the experience gained in these operations

Jan 1, 1987

By T. P. Weldum, B. J. Mahoski, R. S. Rasmussen

A case study of a systematic approach to grinding circuit steady-state optimization is presented. After an overall review of the flow-sheet, two operating circuits were prepared for detailed testing. Functional performance analysis was chosen as the primary modeling system, and, on this basis, a quality-assurance program for data gathering was implemented. A number of circuit-design and operating variables were investigated. Statistical analysis of plant-test results revealed relationships previously unquantifiable by any other modeling technique. Improvements in the classification system and in mill grinding efficiencies were demonstrated. As a result, there was significant energy cost savings.

Jan 1, 2000

By Margaret Armstrong, Chris Roth

One advantage of kriging is that it provides both an estimate of the block or point grade, and an indication of the local precision via the kriging variance. If one assumes that the estimation errors are normally distributed, then confidence intervals for the grades can be calculated. But in mining, grades are rarely normally distributed; in general, they are skew. This is particularly true for precious metals. In this paper we study confidence intervals for variables with non-normal distributions. Using a non linear geostatistical technique, the grades are transformed into their normally distributed equivalents. Confidence intervals are obtained for these normal variables, and back transformed to give the corresponding confidence intervals for the grades, for either points or blocks. This approach is applied to gold data from the Witwatersrand basin in South Africa.

Jan 1, 1996

By H. L. Ford

Flocculant testing should be initiated for economic or performance reasons. When the decision has been made to test, the laboratory can provide valuable information concerning the various products under consideration. Properly conducted laboratory tests can determine: 1. If two flocculants are needed to achieve clarity or density. 2. Ease of mixing. 3. How quickly the material goes into solution. 4. Stability of prepared f locculant solution. 5. Stability of the floc formed. 6. Amount of mixing required for proper floe formation. 7. Optimum flocculant concentration. 8. Optimum pulp density. 9. Approximate location of the point of addition. 10. Single or multiple addition points. When a flocculant shows promise in the laboratory, a plant test should be scheduled. During the plant trial, arrange for normal conditions and start testing with a crew that is most familiar with the unit operation where the flocculant will be applied.

Jan 1, 1986

By M. S. Klima, A. Simard, M. L. Turek

Laboratory testing was carried out to evaluate several devices for recovering clean coal from bituminous coal refuse material. The bulk of the testing focused on using a dense-medium cyclone to process -0.6-mm refuse material. A hindered-settling column and a spiral concentrator were also used to process nominal 1.2 x 0.15-mm material. Product yields and ash contents were obtained for all tests, while partition curves were generated for selected tests from which the characteristic performance parameters (relative density of separation and probable error) were determined. The results indicated that the dense-medium cyclone was capable of cleaning down to 0.037 mm, while the other devices were effective to 0.15 mm. Keywords: Coal recovery, Coal refuse, Dense-medium cyclone, Hindered settling, Spiral concentration

Jan 1, 2003

By J. A. Dille, J. P. Hand, J. D. Brown

The purpose of this paper is to inform members of the coal producing and consuming community about techniques used by The Carter Mining Co. to control product quality at a large surface coal mining operation. During the early years of mining operations, coal quality received adequate attention but the company's main emphasis was to build up its production rate and minimize mining costs. While these goals are still of prime importance, coal quality has received additional attention in recent years. An objective that no coal shipment should exceed any contract or company-imposed coal quality specification has been successfully met. To implement this guideline, geology and coal quality modeling procedures were improved, in-pit drilling and blending programs were refined, and detailed shipment procedures were developed.

Jan 1, 1987

By R. C. Ford

The advent of solvent extraction-electrowinning (SX-EW) technology for recovery of copper from low grade oxide ores has extended the operational lives of many historic mines in the western United States, and made many other orebodies economically viable worldwide. Many of these operations are mature and face closure within the next decade, depending on market conditions. Closure of a large copper heap leach operation has not been undertaken, and differs in some important chemical respects from closure of gold leach pads. Challenges for closure include prediction of solution chemistry and draindown characteristics, determining the benefit of cover placement in semi-arid climates and evaluation of solution management strategies once the economics of copper recovery are no longer favorable. This paper discusses issues pertinent to copper heap closure in semi-arid and arid climates, and strategies for their management.

Jan 1, 2000

By W. J. Wuest, M. J. DeMarco

The US Bureau of Mines (USBM) recently developed a rock-mass classification system for evaluating the structural competency of bedded roof strata. The system is called the coal-mine roof rating (CMRR), When compiled with the companion Lotus 1-2-3 spreadsheet, CMRR data are a useful tool with applications to longwall gate-road pillar design, safety-hazard mapping and artificial roof-support analysis. This paper gives a review of some applications under actual conditions found in current US mining operations.

Jan 1, 1997

By M. Rossi

The use of service variables in geostatistics (grade-thickness) is common in industry when developing block grade models and geologic resource estimates. This is particularly true in the case of sedimentary and stratabound-type deposits. The approach has proven merits when assessing ore reserves. However, there are cases where its application for preliminary data analysis produces biased estimates. One such case is encountered in uranium disequilibrium studies. This paper demonstrates the inadequacy of service variables when performing uranium disequilibrium studies. Disequilibrium analysis is a necessary preprocessing step when radiation counts are used as raw data to calculate uranium reserves. Typically, a probe is used to obtain the gamma counts from open drill holes. These counts are then regressed (and corrected) against chemical assays obtained from core samples. During this process the grade-thickness variable produces an optimistic image of the relationship between probe grades and chemical (true) grades, causing overestimation of the final geologic resource. The problem is analyzed through a case study.

Jan 1, 1993

By V Leus, J. Kallioinen

The large size of the modern flotation cells and the high product flow rate from them has increased the importance of optimal flotation of all the particle sizes and of process control. By treating all the subprocesses of flotation separately a new family of flotation cells and a new concept of optimizing the flotation of coarse and fine particles in separate units but in the same row of flotation cells has been developed. The paper discusses the possibility to enhance coarse particle flotation by varying the froth residence time. A function has been developed between the residence time of the froth, air rate and the froth removal rate of coarse apatite particles. The response of apatite flotation to different control variables has been studied and modelled. The results show that the BPL assay response depends not only on the control variable used but also on the feed assay to the cell. There exists an feed assay dependent region within which the froth assay can be controlled by using the froth residence time as the control variable. These regions can be used to tune a rougher-multistep cleaner circuit to optimal.

Jan 1, 1993

By Victor F. Hollister

This section on case histories of discoveries of volcanic-associated and volcanogenic massive sulfide deposits is divided into a preliminary discussion of models and then into three parts: Kuroko- type, Anyox-type, and shale-hosted. The separation is made to accommodate the use of exploration models, and these may not coincide with genetic models discussed in the literature. The exploration models grew as knowledge was gained concerning ore guides and ore controls in the volcanic-related deposits. The evolution of the genesis of massive sulfide deposits in volcanic terranes from a replacement to a syngenetic hypothesis in the 1950s and 1960s necessitated changes in exploration approaches in ore search. The acceptance of a syngenetic origin for conformable or concordant sulfide masses led to more widespread adoption of stratigraphic ore guides. 'The occurrence of epigenetic stringer ore with and stratigraphically below many conformable massive sulfide deposits did not diminish the importance of stratigraphic ore controls. Proximal conformable sulfide masses were formed near their seafloor hot spring source and normally are underlain by epigenetic sulfides: whereas. distal conformable sulfide masses were deposited away from the hot spring and may have no associated feede; zone. Industry groups that early recognized the syngenetic nature of volcanogenic massive sulfides were responsible for discovery of some of the large and economically significant deposits. Ultimately, the rest of the geological profession accepted the leadership of the early iconoclasts.

Jan 1, 1991

By S. Zaman, John Bulter, M. E. Defoe, Franklin T. Davis

This section deals with the carbon minerals and materials: graphite, tar sands, gilsonite, and diamond. as well as sulfur and the sulfides of mercury, arsenic, antimony, and bismuth. Table I contains the production figures for each of these commodities in the United States and in the world. Specifications for concentrates are also summarized as are prices for concentrates at the time the section was written. In each chapter an attempt has teen made to describe the more common commercial mineral involved with the commodity, the processes used to recover and concentrate the minerals, as well as geographical areas where these processes are utilized.

Jan 1, 1985