Search Documents

By Alex Lowson, Dan Tempelis

The Riverside Badlands Tunnel segment of the Metropolitan Water District of Southern California’s Inland Feeder Project, was lined with a segmented concrete primary lining and a welded steel final lining with the annulus filled with Low-Density Cellular Concrete (really a grout). The paper describes a numerical modeling technique that was developed to determine safe grout placement procedures to avoid pipe flotation, and shows the relationship between flotation and the rheology of the liquid grout. Design details of the steel liners are often not well suited to grout placement, and recommendations are given on how to improve this.

Jan 1, 2003

By Donald L. Gaughenbaugh

Under the terms of the 1970 amendments to the Clean Air Act, the EPA established national ambient air quality standards for a number of pollutants. Sulfur dioxide (SO2) was one of these pollutants. These ambient air quality standards have had perhaps their biggest impact on the power utilities. In an effort to meet the air quality standards set forth by the EPA, utilities using high sulfur fuels have been forced to install flue gas desulfurization (FGD) systems. The majority of FGD systems in operation today are nonregenerable systems, that is the by-product of the system is disposed of, usually into settling ponds. Limestone slurry is the most common reagent used to remove SO from the flue gases. The calcium carbonate (limestone) slurry interacts with the flue gas, absorbing the SO2 and forming a by-product of calcium sulfate/sulfite which is disposed of.

Jan 1, 1986

By Enrique Fernandez

The success of the excavation of a sewage tunnel in a very extreme geological conditions, from river deposits and sandy layers to hard dolomite, and several meters below the estuary under the sea water influence, shows that the choice of a right equipment together with the use of chemical products like foam and polymers enable to dig tunnels in unexpected areas and give solution to the environmental problems. The paper describes the excavation and support process as well as the adopted solutions in every material and during the cross through the intermediate shafts, also under sea influence.

Jan 1, 2003

By William R. Barton

The domestic portland cement industry consumes more than 12 million tons annually of raw materials chemically similar to fly ash. How these materials are used and how fly ash can serve in their place are discussed. Factors influencing whether or not a particular plant will use fly ash in place of an alternate material are discussed.

Jan 1, 1968

By D. Bahrami, G. Danko

Spatial and temporal temperature and humidity variations for 5000 years are simulated in an emplacement airway within the conceptual, high-level nuclear waste repository proposed to be built at Yucca Mountain, Nevada. A multi-scale model is configured using MULTIFLUX, a thermohydrologic-ventilation code. The predicted surface temperature of most waste packages during post-closure exceed 140oC, the threshold limit known for likely localized corrosion for Alloy 22 waste package material. Small amounts of infiltration airflow through the mountain in Panel 5 are found to transport liquid water condensate to some of the waste packages emplaced along the peripheral section of the drift due to edge cooling.

Jan 1, 2004

By Wayne P. Myers

Electricity, as normally thought of by a layman's definition, is a man- made force that has no color, no odor, is not visible, cannot be heard, yet man can control it and make it perform his work for him. A person dare not cheat on it, for it then will master him. It has laws, rules, and regulations that must be strictly adhered to if it is to perform in the safest, most reliable, and economical manner. In the early days of coal mining the power source was man himself. Later man employed steam and compressed air to reduce his muscle power requirements needed in the extraction of coal. By the turn of the 20th century, electricity had become the most common source of power for the coal industry. Steam and compressed air are still found in use in isolated cases today for specific applications; however, they are rapidly being replaced by electricity. Electrical laws and regulations are quite extensive and somewhat complex for the proper generation and use of electricity. Man-made laws, rules, and regulations for the care and handling of electricity, designed for man's safety, are rigidly enforced by Mine Safety and Health Ad- ministration (MSHA), as well as the various state departments of mines.

Jan 1, 1981

By D. Yadon, P. Lee, W. Kelly, C. Stilwell

Rico is a small town in an old zinc mining district in a mountain valley of southeastern Colorado. Mine waste rock and mill “tailings” remained after over 100 years of mining in the area, leaving associated surface water and groundwater impacts. Atlantic Richfield Company is proposing an innovative approach, which uses lime precipitation and wetland ponds (semi-natural system, also called treatment lagoon in a wetland setting) to treat adit water in the Rico area. Besides using a non-conventional treatment approach, a non-conventional (non-Superfund) regulatory/administrative approach is being proposed. This paper will focus on the water treatment issues and solutions, as well as describing the innovative “watershed” regulatory process.

Jan 1, 2004

By W. Ghyoot, J. Boonstra, H. Dijkman, C. Buisman, M. Picavet

Paques and Umicore have demonstrated the feasibility of biological treatment of the highly complex Hoboken wastewaters in a1 m3/h pilot plant at Umicore Precious Metals, Hoboken, Belgium. In the first step arsenic was precipitated from copper smelter effluent as As2S3using biogenic produced H2S. Other metals such as copper, lead and cadmium were also removed as MeS to concentrations well below the discharge levels. Subsequently, sulfate and nitrate were removed to low concentrations (<300 mg/l and < 5 mg/l respectively) in high rate engineered bioreactors. Sulfide produced in the sulfate reduction process was recycled to step 1 for metals precipitation. Selenite/selenate was partly removed in the sulfide precipitation step, whereas the excess was biologically reduced and removed as selenium to concentrations <0.2 mg/l.

Jan 1, 2003

By J. D. Miller

On the basis of nonequilibrium zeta potential measurements by laser-Doppler electrophoresis, the sign of the surface charge of alkali halides in their saturated brines has been established. The results are generally as expected from simplified lattice ion hydration theory. This recent electrokinetic information coupled with the stability and prevalence of collector colloids in such soluble-salt flotation systems suggests that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by heterocoagulation. Experimental flotation results confirm this surface-charge/collector-colloid adsorption model and are presented herein.

Jan 1, 1992

By Rod Heath

The Saskatchewan industry has the advantages of an ore body of a size and consistency unmatched anywhere else in the world, and large, efficient mines with production costs that compare favourably with those in other countries. On the minus side, Saskatchewan is remote from most major markets, and producers face a distribution challenge to reach the offshore markets which is the main focus of this presentation. One of the characteristics of the world potash business is that all of the major sources of production are located in the developed areas of the world, while there is no significant production in any of the highly populated developing countries. The major potash producers are located in Canada and the United States, in West Germany, France, Spain and the U.K., in Russia and East Germany, and in Israel and Jordan. There is currently no significant production in any of the countries in Asia (with the exception of Jordan where a plant is currently in the start-up phase), Africa, Latin America or Oceania, and all of these areas must, therefore, import a11 of their potash requirements from the producing countries.

Jan 1, 1985

By Charles E. Weaver

A core from the La Camelia attapulgite mine in north Florida was studied in detail to determine the detailed vertical variability and the relations of the various parameters. The structural, textural, mineralogical and chemical data indicate there are two major depositional cycles represented within the minable interval. The sediments deposited during the two cycle differ in detail but in general are similar. The environments of deposition grade from shallow marine to lagoonal to tidal flat to marsh. The sedimentary structure (lamination, burrows, pebble conglomerate), mineralogy (attapulgite, montmorillonite, sepiolite, dolomite, calcite) chemistry (Al, Mg, Fe) are closely related to each other and their nature is determined by the depositional environments. Most of the clay minerals and carbonate minerals are authigenic and are therefore particularly sensitive to environmental differences. The variability and environmental features seen in this core are characteristic of the sediments in the general attapulgite mining area. A detailed understanding of the relationships discussed should be of value in prospecting, mining and processing.

Jan 1, 1972

By Chinmay Shingote, Robert Visintainer, Renjie Ke, Jaikrishnan R. Kadambi, John Furlan

Hydrocyclone separators are widely used in various industrial applications in the oil and mining industries to sort, classify, and separate solid particles or liquid droplets within liquid suspensions, which are considered to be multiphase systems. Numerous valuable studies have been conducted in recent years to investigate the flow fields inside hydrocyclones. However, much of the information regarding the performance of cyclones in the literature has limitations and much of it cannot be considered as completely applicable to most real-world applications; many of the studies investigated the flow fields within extremely simplified hydraulic designs that are not representative of the complex geometries or large sizes which are typical in industry. Therefore, in this study, the two-phase flow system inside the actual hydraulic geometry of a milling circuit hydrocyclone is explored with the aid of both computational and experimental techniques (particle image velocimetry (PIV)). More specifically, the flow field with an air core has been investigated. In addition, the air-liquid two phases flow in a hydrocyclone might cause some challenges on both the computational and experimental sides. Two turbulence models are utilized in the numerical calculations: the Reynolds stress model and large eddy simulation. The computational studies are mainly focused on the local flow behavior and the prediction of the dimensions and shape of the air core. Different section planes of hydrocyclone are selected as planes of interest and divided into several fields of view (FOV) for PIV measurements. Two-dimensional experimental velocity vector maps are obtained in each of the fields of view. The computational results are validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles.

By W. F. Mullen

Within the scope of this discussion, artificial dimension stone is defined as any manufactured product used as a substitute for natural dimension stone. The history of the development of these substitute materials is reviewed briefly, representative characteristics of each product are listed, several analyses of their market position are presented, and suggestions are made for recapturing markets lost to these products and preventing additional inroads.

Jan 1, 1959

By S. C. Sun

The grinding of coals for coal preparation has been studied extensively by previous investigators, but no similar work has been done on coal lithotypes (l-4). However, the different natural breakage characteristics of coal lithotypes have been recognized and utilized by the coal industry (5,6) to develop the Longway Burstlein process (7) for the concentration of macerals(8). The specific objective of this research was to determine the relative grindability of lithotypes, obtained from both anthracite and bituminous coals. An attempt was made to relate the findings, wherever possible, to the chemical and physical properties of the tested lithotypes. Another aspect of this research was to ascertain the size distribution and grindability of lithotypes ground at a various number of revolutions in a Hardgrove mill.

Jan 1, 1970

By Gy. Deák

The Romanian mining and especially the salt mining industry is going through a restructuring phase; among others it has to respect the European Environment Act. One of the most important deficits of the salt mining industry is the implementation of monitoring systems for geomechanics phenomena, in order to develop an important information database and form a real base for salt mines stability, prediction and prevention measures. Monitoring system solutions, involving discontinuous and continuous measurements of displacement / deformation fields, around underground excavations, are presented and discussed. In addition, a case study for the stability prediction of an experimental salt off-set, located in the Praid salt mine, using DKRControl method, is presented. The two monitoring systems use different tools, namely measuring tapes (to determine distance between markers in T-D station) and ultrasonic transducers (SM-TDA equipment).

Jan 1, 2006

By G. Robert Moorehead, Peter T. Luckie, Harold L. Lovell, David J. Akers, James K. Kindig

Jigging is a process of particle stratification in which the particle re- arrangement results from an alternate expansion and compaction of a bed of particles by pulsating fluid flow. The vertical direction of fluid flow is reversed periodically. The rearrangement results in layers of particles that are arranged by increasing density from top to bottom of the bed. This response, developed from the many and continuously varying forces acting upon the particles, permits a solid-solid separation more related to particle density and less to particle size than any other "hydraulic-type" process. The stratification is usually carried out in a rectangular, open-top container called a jig, in which the mass of particles (termed a "bed") is supported on a perforated base through which the water flows in alternating directions. The coal particles, in addition to the vertically expanded and compacted bed motion, move continuously, horizontally across the supporting screen. Following the particle stratification, the particle bed is physically "cut" at a desired horizontal particle density plane to separate the desired clean coal product from the more dense refuse. The jig system includes means for continuously introducing the raw coal and for moving the water through the coal bed in a controllable manner, as well as for separating and removing the stratified particles from the system as two or more product streams. In coal preparation, this highly versatile unit operation is applied preferably to a wide size range of particles with top sizes up to 8 in. (20 cm) rather than to a closely sized fraction. In gravity ranges, the process has been applied to gold particles with a density of 19.3 and to coal particles having densities less than 1.30. Single jig washers have capacities from 5 (4.6) to greater than 700 tph (637 t/h) of feed coal. The separation results attainable by jigging have favored this unit operation as optimum for creating a clean coal product as required by steam coal specifications. Al- though the jig is used in preparing coals which are difficult to separate, its limitations to achieve both quality products and high recovery are being recognized in comparison with heavy media-based processes which make sharper separations from feeds having high "near-gravity" contents. The accu- racy of the densimetric stratification in the upper portions of the jig bed are less precise. It follows that coals with more than 10% near-gravity material

Jan 1, 1991

By S. Yap, F. J. Sotillo, L. P. Irwin, F. M. Utsey

Slimes, especially clays, are detrimental to several processes in the Mining Industry. The efficiency of classification, clarification, gravity separation, and flotation decreases significantly in the presence of slimes and clays. This problem is particularly critical in the Phosphate and Sulfide Industries. To reduce the effect of slimes in mineral processing, several desliming techniques and chemical additives are used, such as sodium silicate, sodium carbonate, sulfuric acid, tripolyphosphate, hexameta phosphate, etc. Lately, the Mining Chemical industry has shift to more “Specifically Developed” reagents that offer the most efficient and cost effective performance, mainly using organic polymers. For this purpose, the Mining Chemical Industry needs to understand the crystal chemistry of minerals, the chemistry of the aqueous media, the interactions in solids-aqueous-gas interfaces, the rheology of the system, and the plant operation conditions and parameters. This paper describes the use of surface chemistry fundamentals on the design of an organic polymer capable of modifying the rheology of clayish slurries of a phosphate ore. The change in the rheological characteristics of the clayish phosphate slurries allow fine ore particles to settle faster by reducing the slurry viscosity. Thus, abetter separation of the ore from the slimes is possible using gravitational or centrifugal forces. As examples of the application of this reagent, industrial and pilot plant tests on desliming using tanks and hydrocyclones are presented. These tests showed the reduction of 32%-36% in ore losses for different phosphate ores during desliming operations, and the increase of cyclones desliming efficiency to 80%. Tests were also carried out to improve the rejection of unwanted iron bearing slimes in phosphate feed. These tests demonstrated that it is possible to reduce by 0.25%-1.23% Fe2O3content in the flotation feed product. As a result, significant economical benefits are observed with the use of this new technology without any adverse effect on down stream operations, such as clay settling or phosphate flotation.

Jan 1, 2003

By Michael Deutscher, Jozef F. Zurawski

Part of Capital Improvement Project SE-754 tendered by New York City Department of Design and Construction included installation of a 96-in. (2.47 m)diameter sewer by pipe jacking methods. The pipe selected by the Contractor, EIC Associates, Newark, New Jersey, was a glass-fiber-reinforced thermosetting resin pipe installed in two reaches: 72 m (235-ft.) and 222 m (728-ft.). The machine selected for the excavation was an open face shield. This paper describes the set up of the tunneling operations, subsurface conditions, progress of excavation, pipe performance and other details of the project including unexpected difficult ground conditions that were encountered during excavation and how these conditions were overcome.

Jan 1, 2003

By Marco D. Boscardin

During subsidence, the ground surface may settle, change slope, change curvature, go into tension, and/or go into compression. In response to these ground movements, buildings and buried utilities in the subsidence area may settle, tilt, bend, distort, and sustain extension, compression and/or torsion. In order to develop measures to protect existing structures and utilities, or to design new structures and utilities to withstand potential movements in areas of subsidence, it is necessary to understand the interaction between the ground and the building or buried the utility. This paper reviews subsidence-induced ground movements, how these ground movements are transmitted to and accommodated by buildings and buried pipelines, and how these structures may alter ground movements relative to free field subsidence-induced ground movements.

Jan 1, 1986

By Michael R. Birkos

A new electrotelluric prospecting technique allows the mapping of ore body distribution, lithologic contacts, and voids with accurracy comparable to core drilling. Data is available almost immediately and presented in a format similar to a downhole log. This is done with a passive surface receiver that transduces electrotelluric radiation into an audible signal. Changes in the character of the audible signal lends insight into lithology, porosity, fluid type and medium. Three case histories are presented. The first delineated a paleochannel within a coal seam. The second traced old mine workings and backfill areas. The third identified a high-pressure karst void.

Jan 1, 1986