Search Documents

By M. Wasel

The Gross Rosebel gold deposits are located in theGuiana Shield of northcentral Suriname in South America. The property lies 80 km (50 miles) south of the capital city of Paramaribo. Gross Rosebel covers 170 km2 (65 sq miles) in an area of small hills covered primarily with secondary tropical rain forest, separated by discontinuous savannah (Fig. 1). The concession is accessible from Paramaribo by a 120-km (75-mile) paved and all-weather gravel road. Surficial gold was discovered in 1880 by local artisanal miners. This was followed by small-scale mechanized mining from 1885 to 1939. Placer Development carried out the first systematic exploration program from 1974 to 1977. In May 1992, Golden Star Resources optioned the property. Initial shallow reconnaissance diamond drilling of the extensive surface geochemical anomalies intersected sporadic gold mineralization with no apparent continuity between drill sections. Successive deep augering, trenching and systematic grid drilling, based on information from surface mapping, allowed the development of a preliminary geological model. Further drilling of specific structural-lithologic targets and more complete synthesis of geological data from the trenching and deep auger sampling added to the geological model and defined the multiple controls of gold mineralization. Carefully planned infill drilling on a tighter grid spacing resulted in progressive definition of reserves within six discrete gold deposits. Reserves based on $11.25/g ($350/oz) gold now stand at 35.5 Mt (39.1 million st) of 1.8 g/t (0.053 oz/st) gold, or 62.2 t (2 million oz) of gold.

Jan 1, 1998

By J. A. Herbst, Z. Rogovin, Lo. Y. C., K. Rajamani

Knowledge of the amount of time material spends in a continuous mill in a closed grinding circuit is essential for circuit performance analysis and scale-up design. A convenient method for acquiring this information involves the use of pulse tracers in residence time distribution (RTD) experiments. In typical grinding circuit experiments, RTD measurements are done by injecting a pulse tracer into the mill inlet and detecting it in the circuit exit. In this article, an easy mathematical method for calculating mean residence time and the degree of mixing of material in a mill present in a closed grinding circuit is developed. There are no restrictions on the location of the tracer injection or detection points with this method. Any convenient location in the circuit can be chosen without affecting the residence time distribution measured. The analysis of impulse response data obtained from several commercial grinding circuits using this method is presented.

Jan 1, 1988

By M. Takayasu, J. Y. Hwang, F. J. Friedlaender, G. Kullerud

Al unite has been used as raw material for producing alumina and potassium sulfate fertilizer in Russia for many years. In the United States, this mineral has not been commercially processed though reserves of 5 to 10 billion tons of alunite ore have been estimated. Major constituents of these ores are quartz and alunite. The minerals are finely intergrown and liberation occurs below 10 µm. Adequate separation techniques for such ultrafine particles have not been developed. A new method for the beneficiation of al unite ore is proposed in this study. This method utilizes a small amount of fine magnetite upon which the liberated quartz is selectively flocculated. The co-flocculated magnetite and quartz are then separated from the alunite in a high gradient magnetic separator. Clean products, e.g., an al unite concentrate of 90% grade with 80% recovery, has been obtained from Utah ore. Techniques for selective co-flocculation of magnetite and quartz, separation of the carried quartz, and recovery of magnetite after separation are discussed.

Jan 1, 1987

By B. R. Reddy, Y. V. Swamy, B. V. R. Murthy

Chromitiferous overburden containing nickel in oxide form is reduced with CO-CO2-N2 gas mixtures. This converts the nickel oxide to metallic nickel and restricts the iron oxide to the magnetite state to extract the nickel. Reduction experiments were carried out on 500-g samples in a bench-scale vertical reactor. The tests were run to establish the process parameters, including the optimum partial pressure of CO, the reducing gas flow rate, granule size and roasting time. The reduced calcine is then subjected to an ammonia-ammoniacal carbonate leach to extract nickel selectively as its amine complex. More than 90% of the nickel could be extracted with a volumetric CO/(CO+CO2) ratio of 0.57 at 750°C and a roasting time of 90 min. The addition of 2.5% (by weight) charcoal to the granules improved nickel extraction by 11 % to 19%. Nickel leaching efficiency with ammoniacal solution is compared to the bromine-methanol method.

Jan 1, 2000

By D. X. Tang, G. Wilson, Y. Luo, S. S. Peng

Knowing the location of voids/fractures in roof rock will be greatly helpful for roof support design. The drilling parameters obtained during normal roof bolt installation cycle provide a fast and economic way for determining void location in roof rock. In this research, feed pressure and rotation torque are found to be good indicators for identifying the voids, based on the results of a series of laboratory experiments. A set of computational rules has been developed to locate voids in mine roof using the measured roof drilling parameters and implemented in MRGIS, a software package developed to allow mine engineers to make use of the large amount of roof drilling parameters for predicting roof geology properties automatically. Anew feature, 2D map+3D figure display, is also added to MRGIS.

Jan 1, 2004

By Bing Wang, Jingli Fan, Qinying Song, Fengyu Li, Xian Zhang

"With the background of water shortages and serious water pollution, issues of water involved in energy exploration and utilization have become critical problems affecting urban water usage. In order to identify the relationships of the energy-water nexus, this paper characterizes the energy-water nexus literature using a bibliometric method and based on the Chinese National Knowledge Infrastructure database platform. The results reveal that 1) Scientific outcomes in this field have increased sharply since 2003, with a slightly higher growth rate than that of general disciplines. 2) China Water Resources, Yangtze River and Express Water Resources & Hydropower Information are the dominant journals, and the main research fields include industrial economics, environmental science, and management, among other disciplines. 3) Hohai University, the Chinese Hydraulic Engineering Society, the Institute of Geographic Sciences and Natural Resources Research, and the Changjiang Water Resources Commission are the main research institutions in this field. However, the proportion of publications of these institutions is not high, which suggests that there is no institution dominating this field. 4) According to the keyword analysis, the hot spots in this field include ecological environment, sustainable development, environmental protection, climate change, etc. Energy-mining related keywords have increased over time, implying that the energy-water nexus from the perspective of the energy exploitation industry can become a key issue. At the same time, the frequency of keywords related to sustainable development has been maintained at a high level, and the studies concerned with the impacts of climate change were introduced into this field relatively late. The conclusion of this study provides a foundation for a comprehensive understanding of the current situation as well as for further research in the energy-water nexus field.Introduction As an important strategic resource for national economic and social sustainable development, water has been increasingly focused on by the Chinese Government. Over the next decade, the total water demand of China will continue to grow steadily, which lead to a significant trend of increasing water consumption in the future (Zhang 2013). To reasonably exploit, utilize, conserve and protect water resources, the Water Law of the People's Republic of China was enacted by the members of the 9th National People's Congress Standing Committee in 1988 and after multiple revisions, the latest of which, in September 1, 2016, has involved water infrastructures in the national economic and social development plans of the government at all levels and regulated the rationale for water engineering construction. Thus, in the context of serious water shortages and water pollution, China’s government has taken several measures to make rational use of water resources."

Jan 1, 2017

By P. Muduli, Y. Xi, T. M. Yegulalp, A. J. Arias

A short review of current practices and recent developments is followed by a description of a newly developed approach for solution of the optimum, ultimate pit limit problem. The new approach utilizes network modeling of the problem for solution by maximum flow algorithm. The latest developments in the implementation of maximum flow algorithm present significant time and memory savings as compared to initial development due to Ford and Fulkerson (1956). Results of a series of computational tests are presented to demonstrate how this approach performs as compared to the well-known Lerchs Grossman algorithm. It is also shown that the solution by the new method automatically includes several optimal solutions based on a predetermined number of benches to be included in the analysis.

Jan 1, 1994

By D. Bizier, B. H. Gardner, Y. P. Wang, S. Serata

As part of an ongoing effort to develop more cost-effective and “user friendly” hardware for geomechanical measurements required for underground mine design, Serata Geomechanics, Inc. (SGI) has investigated the potential of borehole pressure cells (WCs) for in situ measurement of stress states and continuous monitoring of changes in ground stress. In particular, because of certain advantages gained thereby, WCs utilizing an elastomer, instead of metal (e.g., copper), for the skin of the pressure cell have been developed. A data analysis technique for determining ground stress state directly from BPC data has been developed. This technique has been tested for salt ground through both in situ applications and computer simulation analysis of the BPC/borehole boundary interaction. This paper discusses the data analysis technique, the results of field and computer simulation testing of its validity, and evaluates the advantages of elastomeric BPCs in relation thereto. It utilizes field data from recent elastomeric BPC applications in the salt mine at Goderich, Ontario operated by the Sifto Division of Damtarn Inc.

Jan 1, 1986

By Y. Kurokawa, R. Kurosawa, I. Iwata, I. Fukuoka, N. Sugita

INTRODUCTION The Ningyo-toge Mine is located in the western part of Honshu, about 800 km from Tokyo. Since the discovery of uranium ore deposit at Ningyo-toge in 1955, different kinds of mining and milling tests have been carried out. A new pilot plant of milling and UF6 conversion is also being under construction. Operations are scheduled to start by the end of this year. In 1979, the uranium enrichment pilot plant was constructed at Ningyo-toge and test operations have started. Thus, the Ningyo-toge area is assigned to undertake the Research and Development of the upstream of the nuclear fuel cycle in Japan. PNC has been strengthening its security measures more than ever. This paper will focus on the disposal of wasted material, especially on the disposal of heap leaching residue, in Japan. URANIUM ORE DEPOSITS The uranium of the Ningyo-toge Mine is characterized genetically by epigenetic sedimentary type deposits. They occur in the host rock of Neogene tertiary fluviatile conglomerates and sandstones which unconformably overlies the Mesozoic-Palaeogene granitic basement covered with lucustrine deposits and volcanic ejecta. More than 12 deposits have been found over the area of approximately 160 km2, and distribution of the deposits are strongly controlled by the so-called channel structure, probably remnants of paleo-streams on the denudation surface of the underlying grantic basement. Each ore body has different shape and dimension respectively, but about 2-3 meters thickness with the average grade of 0.05-0.2% U308 is common feature of the ore bodies. The ore is soft and loose, and it is composed of common rock forming minerals of allogenic origin and their altered products. The chemical composition of the ore depends on the constituents of the country rocks or the pebbles. A primary mineral, ningyoite and secondary mineral, autunite are major ore minerals, although three primary tetravalent minerals and thirteen secondary hexavalent minerals have also been detected. MINING EXPERIMENT Since 1959, various types of underground mining tests have been carried out at Ningyo-toge Mine. The room and pillar method was safe and simple, although the uranium ore recovery was below 70%. After experiment of the retreating long-wall method and slicing mining method, it was found that the modified long wall method was the most appropriate for the underground mining of the Ningyo-toge uranium deposits. This method was completed successfully to increase efficiency up to 2 or 3 times, as compared to conventional methods. MILLING EXPERIMENT In 1964, a small test mill was constructed at Ningyo-toge, and a milling experiment using the Ningyo-toge uranium ore was started. Re-modelling of equipments and improvement of the process lead to the establishment of the technique of the so-called wet process, and produce UF4 directly from the ore. The flow diagram is shown in Fig. 1.

Jan 1, 1981

By Günter Strappler, Max John

When tunneling through karstic terrain, diverse and complex karst structures are to be expected. By means of drilling ahead of the face using drill jumbos, these structures can be detected to such a degree that by applying proper support measures both open karst cavities and karst holes surrounded by boulders embedded in soft rock can be mastered without causing any break-outs. Support measures such as spiles ahead of excavation, sealing off cavities, back?lling with sand, etc. have to be planned schematically and adapted to the dimensions and formations of the karst structures on site. An essential requirement for a smooth excavation procedure is the availablility of all necessary tunneling equipment for excavation by drill and blast as well as for excavation of soil, with experienced tunnel engineers being in charge of any adaptions on site.

Jan 1, 2003

By A. Porvali, V. Agarwal, M. Lundström

Hydrometallurgical recovery of rare earth elements (REE) from NiMH battery waste can be performed using sulfuric acid leaching followed by selective precipitation as double salt (REENa(SO4)2•H2O) by adding Na2SO4 as a precipitating agent. The formed double salts can be treated further with NaOH solution to form REE hydroxides. This study focuses on metamodeling of a simulated flowsheet with design of experiments (DOE). Based on literature survey, a process flowsheet was developed using HSC Sim software. The created flowsheet focuses on circulation of solution containing Na+, K+, SO42- ions and impurities liberated in the NaOH treatment of double salt precipitate. The effect of seven parameters (P1-P7) on seven responses (R1-R7) were modeled using central composite design (CCD). INTRODUCTION Nickel metal hydride (NiMH) battery waste can be considered as an urban mineral due to the presence of valuable metals like: Ni, Co and rare earth elements (REE) (Larsson et al., 2013). In NiMH battery waste leaching experiments, sulfuric acid has often been employed as a lixiviant (Pietrelli et al., 2002,Zhang et al., 1999,Rodrigues and Mansur, 2010,Porvali et al., 2018). The key advantages of sulfuric acid are its stability and cost-effectiveness compared to other mineral acids such as HCl and HNO3. However, the usage of sulfuric acid in NiMH battery waste leaching poses simultaneous challenges and advantages. Limited REE solubility can be taken as benefit when recovering REEs double sulfates after solid-liquid separation. However, sodium and potassium hydroxide, present in electrolyte residues in the battery waste, can cause in-situ precipitation already during leaching due to limited solubility, thus decreasing the total REE recovery (Porvali et al., 2018). However, this problem can be circumvented by washing the electrolyte residues off the raw materials. Subsequently, the REEs may be precipitated in bulk as a mixed double salt out from the solution at very low pH with minimal co-precipitation of Ni and other metals. This relatively easy separation method can be extremely advantageous in the case of such a complex solution matrix with relatively high REE concentrations (conc.). Once REEs have been precipitated as double sulfates as per eq. (1) (Porvali et al., 2018), the resulting double salt precipitate lacks applications without further treatment. Direct thermal treatment would generate sulfur dioxide emissions and likely require high temperatures in order to transform double sulfates into REE oxides. Furthermore, the precipitate contains Na ions, which would need to be removed by chemical treatment from the calcined REE product. In the context of circularity of raw materials, it can be taken of a remarkable benefit if the sodium and sulfur present in the double salt could be reused instead of wasting them into the side streams. To that end, in this simulation study, the double salts are converted by dissolution and precipitation to hydroxides which are readily treatable, e.g. with total dissolution and solvent extraction, for further purification (Abreu and Morais, 2010):

Jan 1, 2019

By Armine F. Banfield

Selection of a plant site is becoming increasingly more difficult and important, mainly due to advances in technology, antipollution laws and changing economic, social and community conditions. Discussion falls naturally under three headings: economic considerations, terrain considerations and environmental considerations. Aside from acquisition of surface rights, problems having to do with terrain, or topography, usually can be dealt with by management alone. Economic considerations largely involve decision-making by management plus negotiations with government regulatory agencies acting under set rules. Environmental considerations, such as air and water pollution, townsites, housing, schools, noise abatement, appearance, surface rehabilitation and the like usually are under the control of federal, state or municipal bodies with a large degree of decision-making. Successful solution of environmental problems often requires lengthy negotiations, during which public relations by the mining company play an important part. Existing union regulations or customs may confine decision- making and the establishment of wage rates, working conditions and regulations. These usually require considerable planning and negotiation. Initial production often is delayed by formal negotiations involving environmental considerations. Surface facilities usually can be divided into two broad categories: those for concentrating ores--such as gold, silver, base metals, low-grade iron ore and potash-which should be close to the mine to reduce ore-transportation costs to a minimum, and those where the ore is shipped elsewhere for treatment, such as direct-shipping iron ores, complex high-value ores requiring specialized treatment and ores from which special products are derived for local markets. The long-term aspects of plant-site selection too often are given no or insufficient consideration because of immediate financial limitations. As a result, additional capital expenditures may be required later for relocation of townsites, roads, railroads and plants to provide additional room for extension of open-pit operations, tailings disposal, storage, or danger to foundations through underground subsidence or open-pit mining. In the past, hillside sites for concentrating plants were preferred to take advantage of gravity-feed methods The modern trend, however, is to place as much equipment as possible on approximately the same level. Some costs relating to plant sites are included in this section. They are ranges as of the year 1970, and are offered only as general guides. Such costs will vary widely with geographical location and, of course, are subject to escalation due to increases in wage rates and cost of materials. Items in the bibliography contain more detailed and comprehensive data on specific subjects. Most contain bibliographies of their own.

Jan 1, 1973

By Michael Chender

The rapid and continuing expansion of computer and communication capability is giving birth to profound changes in the business environment. Some commentators hold that the basis of the world economy has already shifted from industry to information. Regardless of the overall implications of these changes, it is now clear that every company potentially has both access to and a need for much more information for decision making than was the case a few years ago. The importance of information to the mining industry has been underlined by the rash of unexpected economic and political developments and by the accompanying market volatility that have marked the past decade. It should be abundantly clear to even the smallest mine operator that the price for his output can be instantly affected by unexpected developments halfway across the world. Nevertheless, many mining companies still are much less sophisticated about information than they might be. For many, the historical feeling that information is an unnecessary luxury for a production-oriented business still seems to linger. On the other hand, the overwhelming volume of source material, uncertainty as to its accuracy, and the problems of finding relevant material when needed, presents stumbling blocks to viable systems of information management. Introduction When a company needs certain information, it has two basic alternatives. It can either research and develop the information in-house or pay for someone else to do it. Few mining companies have the in-house capability to assemble information needed for careful planning. On the other hand, companies often engage consultants to find information that is in fact easily accessible. All too often companies give up on procuring needed information because of the frustration of not being able to find it, and of not wanting to pay seemingly exorbitant sums for someone else to produce it. The result is poor planning. This article addresses two aspects of the information problem-finding the right sources and then accessing the particular information desired, especially as it pertains to nonferrous metal exploration and development issues. In the first section, major English-language sources that report on exploration and development (excluding primary sources of geological information, such as technical journals) are discussed.* In the second section, some available techniques for efficiently accessing this information are presented, focusing on the new MINESEARCH database system. Part One: The Information Following the News The most obvious way to follow exploration and mining developments from a distance is through regular mining media. Many active mining districts have local newspapers, usually published in the district's major towns, that give extensive coverage to miningrelated activities. For instance, to follow activities in Idaho's Coeur d'Alene silver district, one might subscribe to the Kellogg Wardner News and/or the Wallace Miner. Similarly, one might get the Sacramento Bee for news of current mining developments in north-central California. The American Metal Market, published in New York, is the daily newspaper that covers the metals industry as a whole, both in the US and abroad. Its coverage is weighted towards the refining, manufacturing, and consumption end of the business, but it frequently carries stories on mining activity, company dealings, and market outlooks. For news of major mining companies, the daily Wall Street Journal provides occasional coverage of North American companies, while the Financial Times of London serves as probably the best single source for worldwide company information. International Coverage There are three metals industry weeklies that have broad international coverage and readership. These are Metal Week, Metal Bulletin, and Mining Journal. Each has its strengths. Metals Week, a McGraw-Hill newsletter, focuses primarily on news of the metals markets, concentrating on those developments that are seen to most directly affect the price of nonferrous metals. Metals Week is strongest on North American news. Metal Bulletin, published in London, is particularly strong on

Jan 4, 1983

By E. Harrison

The Greens Creek Ore Bodies are located approximately 18 miles southwest of Juneau, Alaska in an area on Admiralty Island classified as a non-wilderness national monument. An area-wide stream sediment geochemistry program targeted the deposit in October of 1973. Today, after 37,000 meters of combined surface and underground diamond drilling, three ore zones are known to exist with total reserves approaching 4.1 million tonnes. Lying within moderately folded metasediments of an undetermined age, these orebodies are thought to be of seafloor exhalite orgin and contain unusual and impressive amounts of gold, silver, lead, zinc and copper.

Jan 1, 1986

By Jon C. Yingling

A control system for reducing peak loads on mine conveyor networks is proposed. The system involves continuous monitoring of flows into the conveyor network and section feeders with variable discharge capability. The control strategy uses differences in material transit times from various production units to the transfer points in the network to forecast load levels that will be intersected by the discharge of the controlled feeders over future time intervals. Feeder setpoint adjustments are made to prevent excessive peaks in the combined flows at the transfer points, while maintaining adequate feeder throughflow to avoid production bottlenecks.

Jan 1, 1992

By Thomas D. Henderson, Wayne R. Hopkins, Arthur Lynch

Brought on stream in 1975, the 10,000-tpd copper oxide processing plant of Anamax Mining Co. at Twin Buttes, Ariz., is now at design capacity. Based on acid agitation leaching, solvent ion exchange, and electrowinning, the Anamax plant bridges an ore to metal gap by producing mine site copper cathodes from lime-bearing oxidized feed. Until recently, such material was considered submarginal because copper recovery was uneconomic using conventional methods. The new Twin Buttes oxide plant, the largest of its kind in North America, is one stage in the expansion of Anamax, a joint venture owned equally by The Anaconda Co. and Amax Inc. Other phases include an accelerated stripping program in the pit, an expansion of the sulfide concentrator from 32,000 to 40,000 tpd, and construction of a 57 MW diesel generating station for the oxide plant. Once the basic oxide flowsheet had been selected, Anamax awarded a contract to a joint venture of Arthur G. McKee and Co.' (Western Knapp Engineering Div.) and Davy Powergas' (a member of the Davy International group). The contract covered process design, engi¬neering, procurement, and construction. The property, identified by Banner Mining Co. in the 1950s and developed by Anaconda, was put into production in 1965 as an open pit mine equipped with a 32,000-tpd sulfide flotation concentrator. The Twin Buttes mine has since become one of the largest earth¬moving operations in the world, excavating some 10 tons of waste per ton of ore. At the original sulfide mill feed rate, the mining fleet moved 375,000 tpd of material (225,000 tpd alluvium and 150,000 tpd of rock). The most significant copper mineral in the ore body is chalcopyrite, which is scattered in pockets of weak mineralization. Cap oxidation has progressed to depths of several hundred feet, principally as chryso¬colla. Present estimates place minable reserves at 347 million tons of sulfide ore grading 0.6% copper and 55 million tons of oxide ore grading 0.9% recoverable copper from 1.25% total copper. The nonre¬coverable fraction is composed of native copper and insoluble copper oxides and sulfides. The oxide ore has been partially stripped, and 25 million tons having a copper content greater than 0.6% have been stockpiled. The stripping of oxide ore to expose sulfides will continue for several years. The copper oxide studies launched by Banner Mining in the 1950s were continued by Anaconda. Process routes investigated included: acid leaching; cyanide leaching; segregation roasting; chlorination, oxidation, and reduction; flotation in combination with leaching; cal¬cite flotation plus leaching; copper oxide flotation; and sulfidization flotation. By late 1968 test work favored a low temperature roast followed by an ammonia-ammonium carbonate leach of the ore. During this period, acid leaching had been discounted because of excessive con¬sumption of expensive acid by the high limestone ore matrix. Restric¬tive SO2 emission controls in 1971 suggested an increase in acid production and availability at a lower cost. Research then switched to acid leaching, resulting in development of the present flowsheet. Mechanically agitated leaching in a cascaded series of tanks was selected in preference to vat leaching after piloting a stirred-tank system. Preliminary testing of vat leaching indicated that inter-vat solution clarification problems could be caused by gas evolution from leaching of high limestone ore. Lack of research time for resolution of this problem, plus success of the pilot agitation system, dictated the final flowsheet selection. In 1973 Anamax decided to proceed with agitation acid leaching to produce liquor for a solvent ion exchange (SIX) and electrowinning (EW) installation. At that time, such systems were proving their eco¬nomic viability, and they allowed direct recovery of high quality cath odes while bypassing the smelting and refining of lower grade cement copper precipitates. The Anamax oxide plant processes a grade of about 1% recovera¬ble copper from stockpiled sources and new mine production. Unit operations include size reduction, agitation leaching, countercurrent decantation washing of residue, pH adjustment of solution, clarifica¬tion, solvent ion exchange, and electrowinning of copper, with a mini¬mum of environmental impact. The feed to the primary crushers is composed of: 1) -10-in. stockpiled oxide ore, which has passed through the mine crusher and has been grade-segregated to allow blending for a consistent feed material. 2) -4-ft ROM oxide ore stockpiled in the early mining operation. 3) -10-in. ore currently being mined. Ore is delivered in 100-ton mine trucks to a dump pocket, where an apron feeder transfers the ore to an inclined 6-in. fixed grizzly. The grizzly oversize passes through a 48 x 60-in. primary jaw crusher, where it is reduced to -6 in. The fixed grizzly undersize and the crusher product are conveyed to a 4-in. vibrating grizzly. Oversize from this grizzly reports to a 7-ft Standard cone crusher, where it is reduced to -1 in. The crusher product and the vibrating grizzly undersize are conveyed to two 8 x 20-ft double-deck vibrating screens that operate in closed circuit with two 7-ft short head cone crushers. Screen undersize (-1/2 in.) is delivered to a covered conical fine ore stockpile with a designed live capacity of 15,000 st. Beneath the stockpile are ten Pioche belt feeders feeding two conveyor belts that supply the milling circuits. Each group of five feeders has two variable speed and three fixed speed drives. Grinding to 95% -48 mesh is done in two parallel lines, each consisting of an 111/1 x 18S -ft rod mill and a 12' x 30-ft ball mill in open circuit. Water is added to maintain a pulp density of 72% solids in the mills. Further water additions are made to the ball mill discharge sumps to create a 60% solids slurry for transfer to the leaching reactors. The nominal grinding rate is 440 tph solids. A splitter box on the product from the mills separates the incoming slurry into two streams, one for the leaching reactors and the other for the pH adjustment reactors. This split is determined by the lime content of the feed material and the pH of solution entering the pH adjustment reactors. Five 30-ft diam by 31-ft high mechanically agitated, rubber-lined leach tanks are arranged in cascade, with gravity transfer from one to another by enclosed launders. Concentrated sulfuric acid (93.2%) from storage is added to the pulp principally at the first leach tank, and the reacted slurry leaving the cascade after a 5-hr residence time at 50% solids is pumped to countercurrent decantation (CCD) wash thickeners.' At this point, most of the soluble copper has been leached from the ore. Up to 250 lb of sulfuric acid is consumed per ton of ore, the acid being supplied in tank cars from a nearby smelter. Leached slurry at 50% solids is washed countercurrently with return raffinate from the SIX plant in a series of four Doff-Oliver center caisson, 400-ft diam thickeners. Solids advance from thickeners No. I through No. 4 to the tailings dam. SIX raffinate advances from thickener No. 4 to thickener No. l, where a pregnant solution overflows to pH adjustment. To optimize solvent extraction, the pH of the pregnant solution from CCD thickener No. I is adjusted from 1.5 to 2.5 by adding unreacted ground slurry (split from the grinding circuit) to the preg¬nant overflow of No. I CCD thickener. The resulting slurry is retained for 45 min in three mechanically agitated leach tanks. CO, generated during leach and pH adjustment is ducted to a demister, where entrained acid droplets are removed. The cleaned CO, and the No. 4 CCD underflow are the only effluents from the plant. The underflow of No. 4 thickener mixes with tailings from the sulfide concentrator and is neutralized. Slurry exits the pH adjustment vessels at about 10% solids and

Jan 1, 1985

By S. L. Bessinger

Introduction Extensive testing in the past ten years has shown that where a uniform natural gamma background is present in the strata bordering a seam, the thickness of the boundary coal left in place after mining can be determined by measuring the attenuation of that radiation (Nelson and Bessinger, 1989). Measurements made by the authors in underground mines in Pennsylvania, West Virginia, Ohio, Illinois and Kentucky and by others in Wyoming and New Mexico have shown the presence of such a gamma background (Nelson. 1989). Natural gamma coal-thickness sensors of several configurations have been tested in mines owned and operated by the Consolidation Coal Company (Consol) in Pennsylvania and West Virginia (Nelson and Bessinger, 1988). This paper describes the installation of a natural gamma coal-thickness sensor on an operating continuous miner. Previous tests had shown that the NGB-1000 coal-thickness sensor manufactured by American Mining Electronics, Inc., of Huntsville. AL, is an accurate, mine-worthy instrument. This large gamma detector consists of a sensing head and a control panel. The sensing head contains thallium-doped, sodium iodide scintillating crystal, which is coupled to a photomultiplier tube. The control panel contains the electronic components required for calibration, count conversion and display to the operator. Methods Conditions at a Consol mine in northern West Virginia require that 10 to 15 cm (4 to 6 in.) of coal be left at the roof boundary of continuous miner development sections. This roof coal is required because the shale of the immediate roof is friable and unstable. In the past, operators have used a dirt band that is usually visible near the top of the seam as a guide in maintaining the proper cutting horizon. However, this is not always reliable. Earlier observation showed that the actual thickness of the coal left on the roof varied widely; further, it was noted that occasional, accidental excursions into the immediate roof required supplementary roof control measures, such as installation of planks or center bolts. Thus, it was concluded that operators needed a better source of guidance for control of the cutting horizon, and a roof-coal thickness sensor was scheduled for installation. The NGB-1000 sensor was installed on a Joy 12CM10 continuous miner in June 1988. The sensing head was mounted on the cutter boom of the miner, and the control panel was mounted in the operator's cab. Power for the sensor was initially derived from an intrinsically safe battery power supply. Initial measurements with the sensor showed that the calibration was the same as that used in earlier tests at two other mines, indicating the uniformity of the natural gamma background above the Pittsburgh seam. Operating personnel were initially skeptical of the instrument's accuracy, and were hesitant to use its readings as a guide in maintaining a proper cutting horizon. Because gamma attenuation, the instrument's operating principle, is somewhat abstract, attempts to demonstrate the instrument's accuracy by explaining that principle were generally ineffective. It was found, however, that an operator could usually be convinced of the usefulness of the instrument by placing a large piece of coal of fairly uniform thickness over the instrument's sensing head and allowing the operator to see that the instrument reading increased by an amount very near his estimate of the thickness of the piece. The mine was provided with seven battery power supplies and a charging station. The charging station was kept in the lampman's office, and the mechanic on each shift was instructed that he was responsible for two battery power supplies each day: a freshly charged one to be taken in at the beginning of his shift and a depleted one to be brought out at the end. This system worked well for a few weeks, but eventually some battery power supplies were left in use so long that their batteries were discharged too deeply to allow recharging. In addition, transport and recharging of the batteries represented an additional task for the mechanics, who were already very busy. Consequently, a request was filed with MSHA to allow the sensor to be powered through intrinsic safety barriers by an electronic power supply connected to machine power. The permit was granted, and the sensor was connected to machine power. After the sensor was connected to machine power, the only operating problem experienced was occasional failure of cables. A supply of the required cables was made and delivered to the mine so damaged cables could be quickly replaced. Much of the cable damage could be eliminated by slight modifications to the miner during a rebuild, so that cables could be installed in more protected locations. After the sensor had been in operation for about two months, a survey was made to determine its effect on continuous miner operations. In previous research, coal thickness measurements made in 88 locations by the natural gamma method were compared to measurements made in the same locations by observing drill cuttings and by inspections of drill holes with a borescope. That research showed that the gamma method is at least as accurate as the other two methods (Nelson and Bessinger, 1989) and is also much easier to use. The object of the survey described here was not to assess the accuracy of the natural gamma measurements. but rather to determine the effectiveness of the sensor output as a guide for the operator in maintaining control of the cutting horizon. Thus a smaller, hand-held gamma detector

Jan 1, 1992

By James Watson Baxter

Fluxes are used to promote pyrometallurgical processes that rely on adhesion (soldering or brazing) or fusion (gas and arc welding) to join metallic surfaces. In the adhesive processes, the metal surfaces to be joined are not melted; the join is formed using a filler metal with lower melting point than the base metal. Fusion welding involves use of heat in excess of the melting point of the base metal. The fused joint may be achieved either by simply fusing together metal surfaces brought in contact with each other or by introducing additional molten metal of similar composition to form a fused joint. ADHESIVE PROCESSES--SOLDERING AND BRAZING In order for molten filler metal, solder or braze, to spread in a manner that creates a successful join; the work surfaces on the base metal must be thoroughly cleansed. Fluxes remove stubborn oxide films and other surface contaminants, promote wetting of the work surfaces, add fluidity to the solder or braze, and enhance workability and ease of spreading. Brazing processes involve higher temperatures than those reached in soldering. Brazing fluxes, which must remain active and effective at the higher temperatures, differ from those employed in soldering. Some common fluxes used in adhesive processes are rosin for soldering tin and electrical connections, hydrochloric acid for use in soldering galvanized iron and other zinc surfaces, and borax for brazing. Soldering and brazing are similar processes, the primary difference being the temperature at which the joining operation is carried out. Soldered joints, produced with low-melting-point fillers (solders) that melt and flow at temperature less that 450°C (Althouse et al., 1988) can sustain loads of 1 to 1.7 MPa for extended periods of time (Anon., 1966). Brazing involves the use of filler materials with melting points commonly above 500°C and generally provides stronger joints than those obtained with solder. Both processes require local application of heat to melt and spread the filler so that the molten filler can wet (adhere to) the base metals by alloying and diffusion. Soldering Soldering is a means of joining metals by adhesion using a metallic bonding alloy as the filler, commonly a mixture of lead and tin. However, the adhesion of solder depends more on its ability to be keyed into minute surface irregularities than on alloying. The most familiar application is to provide and secure electrical connections. Soft solders can range from 1 to 70% tin with the remainder mostly lead. However, for general-purpose, soft-solder work, the alloy is commonly 50% lead-50% tin. Higher lead contents provide a wider range in the melting temperature and, for this reason, a 60% lead-40% tin alloy, which yields a mushy mixture, is used for wiped joints in lead sheet and pipe work. Conversely, 40% lead-60% tin alloys are used in soldering tin and other low- melting-point materials for which a narrower range of melting temperature is required. There are numerous other solder compositions such as tin-silver, 95% tin-5% silver and antimony-tin, 95% tin and 5% antimony (Carlin, Jr., 1992). Heat needed to melt and spread the solders is commonly provided by electrically heated, copper-tipped soldering irons or by means of torches; the solder is applied by hand, usually face-fed by means of wire. For wiped joints in plumbing and lead-cable splicing, the solder is manipulated with cloth pads. The molten solder wets the joint surfaces and is drawn, by surface tension, into minute fissures and capillary openings. Other applications involve use of induction heaters and furnaces with pre-shaped solder appropriately placed prior to fluxing and heating. In some processes, the joints are immersed in molten solder. Constituents and Role of Soldering Fluxes: Soldering fluxes generally fall into one of three categories: highly corrosive fluxes, intermediate fluxes, and noncorrosive fluxes. These same categories are sometimes designated inorganic, organic and rosin-based respectively (Althouse et al., 1988). Common constituents of each group are discussed briefly below. Corrosive Fluxes (Inorganic). Work with aluminum, magnesium, stainless steel, high alloy steel, aluminum bronzes, and silicon bronzes is carried out at temperatures in the upper portion of the range for solder operations. Soldering these materials requires use of highly active, corrosive fluxes to remove and prevent the formation of the especially stubborn, hard, oxide films that form on these materials upon exposure to the atmosphere. The corrosive fluxes consist of inorganic acids and salts that are applied either as pastes or dry. They are active at elevated temperatures and, since they remain active after the soldering is completed, must be completely removed. The main constituent of most corrosive fluxes is zinc chloride with a melting temperature well above the solidus temperature of most commercial tin-lead solders. It is made by the action of hydrochloric acid on zinc. When zinc chloride is used alone, un- melted particles of this corrosive salt get caught up in the joint and weaken it. For this reason, other inorganic salts such as ammonium chloride (NH4Cl) or sodium chloride (NaCl) may be added to lower the melting temperature. A mixture of zinc chloride and ammonium chloride is very effective because the excellent oxide reducing properties of ammonium chloride and the protective action of the molten zinc chloride combine to produce a fluxing action superior to that achieved when either is used alone. In addition to zinc chloride, ammonium chloride, and sodium chloride; common con-

Jan 1, 1994

By L. T. Larson

Had the blank on the Abstract form been sufficiently spacious a more appropriate title for this paper would be: Neogene Tectonism, Magmatic Activity and Hydrothermal Precious Metal Mineralization in Anatolian Turkey; an Analog with the Basin and Range Province of the Western U.S.? Like the alternative title no thing in Turkey is simple. Its history is long and convolute; its culture fascinating; its metallogeny diverse and its geology very complex. This paper will focus only on the geology of western' Anatolia and the precious metal potential of this third of Turkey. The argument is in the article but to save the reader time and suspense I'll put my conclusions up front- the potential is great and the possibilities exciting.

Jan 1, 1989

Introduction The objective of the design and operation of a mine is to make as much money as possible within certain reasonable and responsible constraints. The imposition of constraints on the objective of maximizing profits can result in an optimum mine design. This paper deals with the maximization of profits. Optimization will be discussed in a future paper. In the mining industry, it is generally accepted that the maximum economic recovery is defined by identifying the reserves and the sequence of mining that results in maximum net present value (NPV) or discounted cash flow-rate of return (DCF-ROR), as indicated in Fig. 1 (see Lemieux, 2000). Current parametric analyses techniques, such as varying the mining costs; profit reservation; sales price or metal content, to define pit limits and mining sequence technically referred to single, double or triple parameterization, do not assure that the curve in Fig. 1 will be maximized. In defining the sequence, the first material to be mined should be the first grouping of recoverable mineral that has the highest after-tax unit value and that forms a feasible mining unit. The assumed mining of the first pit should be followed by the assumed mining of the second most profitable and practical pit or pit expansion. If this process of grouping and sequencing is followed until the profitability approaches zero, the general sequence required to extract the maximum economically recoverable reserve is identified. The curve in Fig. I is constructed by calculating the NPV for a series of sequences, each assuming operations are terminated on successively lower profit pits. If the operation ceases on a pit with too high of a profit, opportunity is lost, and the NPV is lower than the maximum. The NPV curve peaks and then starts to decline before the zero-profit pit is assumed mined. This occurs because the money invested in advanced stripping would have produced a greater return if it was invested at the dis¬count rate. The maximum economically recoverable reserve is defined by the pit limit corresponding to the maximum NPV or DCF-ROR. Pit and phase definition The real challenge of reserve definition is identifying the phasing and after-tax profit per ton, so that the curve in Fig. 1 can be plotted. The after-tax profit cannot be properly addressed until after the pits are designed, the production is scheduled and the cash flow is estimated. Throughout the years, many investigators have ad¬dressed this problem. A major thrust of the famous paper in which Lerchs and Grossman (1965) presented their algorithm was to identify a sequence that would produce a result similar to that identified in Fig. 1. Whittle's (1988) four-dimensional analysis is designed to address this issue. The author addressed this same issue in a paper presented to the 1968 Canadian Institute of Mining national convention (Lemieux, 1968). Without a relatively simple methodology to con¬struct the curve in Fig. 1, the number of iterations in a trial-and-error method becomes prohibitively burden-some. The pit designer seeks a simple pit-planning parameter that will serve as a proxy for the after-tax profit per ton used in defining the curve in Fig. 1. The designer's goal is to apply this pit-planning parameter using standard pit-wall location techniques to design a series of pits that will provide a guide to the sequencing. Common techniques used to position pit walls are strip-ratio limits, highwall incremental analysis, floating-cone methods or "maximizer" applications1. Costs, revenues, noncash charges, taxes and profits are usually structured on a unit basis for use in the pit-wall location analysis. Application of the proxy parameter using the pit-design tools should, ideally, result in the definition of pits and sequences that will maximize the curve in Fig. 1. 1 The pit-design tool frequently referred to in the literature as an "optimizer" defines a pit boundary that maximizes the value contained within based on the input parameters and the safe pit-wall angle. The optimization of the pit design involves selection of rate of production, cutoff grade, product quality and other considerations. These considerations constrain the maximization of value. Therefore, pit-design tools that maximize value should be called "maximizers."

Jan 1, 2000