Search Documents

By Y. A. Attia, D. K. Sengupta, H. A. Hamza

Increased recycling of waste paper has been emphasized in recent years in both the United States and Canada for environmental and economic reasons. Removal of ink particles from waste paper pulp is therefore necessary. One of the most promising methods for ink removal is froth flotation. This study investigated the feasibility of a simplified flotation scheme and found that about 90% to 92% ink removal can be achieved. Also, a 95% to 97% ink removal is achievable if a hydrophobic polymer is used ahead of the flotation stage. Clean paper pulp recovery was over 90%. The effects of pulping pH, flotation pH and concentrations of flotation and polymeric reagents are discussed in the paper.

Jan 1, 1995

By Y. K. Yen, J. D. Miller, C. L. Lin

Particle size segregation is a common phenomenon in many particulate processes and has many undesirable effects. The size segregation which occurs on a belt conveyor causes a serious problem for on-line particle size measurement using image-based techniques. Whether particle size distributions measured from the top layer of the belt are representative of the total particle population is largely dependent on the degree of size segregation. Therefore, it is important to understand the nature of such size segregation in order to make appropriate corrections for on-line particle size analysis. Monte Carlo simulation has been used to provide segregation information on particles with simple geometry and the results can help to determine important factors in experiments with irregularly shaped particles. It is expected that the relationship between the particle size distribution of the top layer and that of the entire particle population on a belt conveyor can be formulated as a model based function.

Jan 1, 1997

By J. W. Wilson, Y. P. Wang, M. H. Erten

The use of water is still the most effective and economical means for dust control in underground coal mines today along with dilution by the ventilation current. Studies have shown that the dust capturing capacity of water is a result of a balance of many intermolecular forces. Surfactants are known to reduce such forces by affecting both the surface tension of the liquid and its interfacial tension against a solid. Surfactants can be added to the water sprays to facilitate the dust capturing capacity. A laboratory scale model has been developed in which surfactants were added to the spraying water and preliminary data indicates positive results.

Jan 1, 1991

By Y. C. Kim, I. S. Roditis, P. K. Medhi

The strongly skewed grade distributions and the need to estimate the local recoverable reserves in a selective mining environment are the two problems that ordinary kriging (OK) cannot easily handle. With the recent introduction of the non- parametric, distribution-free technique of indicator kriging (IK), the above problems can be solved. This paper describes the result of performance evaluation of IK in an open-pit gold-silver deposit. For performance evaluation, the predictions of local recoverable reserves using IK were compared with the actual reserves based on blasthole information. The IK estimator, although a bit optimistic (or overestimating), performed very well in predicting the total recoverable ounces of gold from each panel on a test bench. The OK estimator was also used to try to predict local recoverable reserves, by treating each panel as either waste or ore, depending on the panel's average grade. Under this criterion, OK was found to be quite biased and pessimistic (or underestimating).

Jan 1, 1988

By J. A. Herbst, J. E. Bohrer, Y. C. Lo

A systematic approach has been developed to analyze a phosphate grinding circuit with a view toward determining promising alternatives for increasing mill capacity. This analysis was carried out and capacity increases were predicted in the context of detailed population balance models developed for the plant ball mills and classifier systems. Model development and verification was performed using data obtained in a series of batch tests and two plant test campaigns. The effects of feed rate, percent solids, ball size, and mill material filling, etc., on grinding were investigated in the laboratory and plant. Residence time distribution tests were also performed to determine the transport behavior in the mill. The population balance models were found to provide accurate predictions of full-scale grinding circuit performance. Based on the findings of this study, additional capacity in excess of 25% was predicted for these ball milling circuits by a proper combination of ball size change, mill dilution, and adopting screen classification in place of hydro-cyclones. These predictions have been confirmed by plant tests in which the recommended operating changes have been implemented. Understanding the effects of operating variables on breakage kinetics and the interplay between kinetics, transport, and classification has contributed significantly to increasing the mill capacity.

Jan 1, 1988

The ventilation of a mine is one of the key elements to a successful mining operation. It is, or should be, one of the primary concerns of the mining engineer at an underground mine. Too frequently, however, insufficient thought is given to future requirements. As a result, the mines suddenly find themselves with ventilation problems that cannot be corrected economically, or in short order, and have to suffer the consequences of being on the verge of having units shut down from time to time until the venlilaltion system can be improved. Insufficient ventilation in capital-intensive mining can cause production losses, the values of which far outweigh the significant costs of providing and operating an adequate ventilation plan. Many theories, and techniques in planning and control of underground ventilation systems have been developed over the years . It is the intent of this paper to point out some of the fundamental concepts, from the practical point of view, in the design and operation of a ventilation system, with special reference to underground mines using a room-and-pillar method.

Jan 1, 1986

By John W. Rozelle, David S. Bolin

INTRODUCTION During the normal course of a mining project, a feasibility study will be prepared that addresses all the aspects of the project including geology and mineral inventories, mining and geo- technical, metallurgical processing, infrastructure, environmental considerations and economic analyses. These studies are prepared for various reasons. Occasionally, a feasibility study will be prepared solely for use within a company as justification for development expenditures, however, these documents are frequently submitted outside the company either to raise funds from financial institutions or from public financing on one of the various securities exchanges. Mineral industry consultants are often called upon to participate in the preparation of feasibility studies or to conduct an independent audit and review of an internally prepared study. As the recoverable mineral resources form the foundation upon which the balance of a feasibility study is based, including the economic analysis of the project, the resource aspect of the study is examined very carefully by financial and securities organizations. The balance of this discussion is directed toward the various geological and resource estimation aspects of feasibility studies that experience has shown to be of particular importance. Much of this discussion will be directed toward open pit gold operations, although the principles are applicable to any type of deposit. 2.0 GEOLOGIC RESPONSIBILITIES IN FEASIBILITY STUDIES The principal geological effort in the preparation of a feasibility study is generally dedicated to the following areas: - Preparation of Geologic Reserve/Resource Estimates - Condemnation of Sites for Facilities, Access Roads, Leach Pads, Waste Dumps and Tailings Disposal - Collection of Geotechnical Data - Provision of Mineralogical and Petrological Data Pertinent to Metallurgical Processing - Selection of Appropriate Bulk Sampling Sites for Collection of Metallurgical Samples Each of these items will be addressed in detail in the following sections. 3.0 RESERVE/RESOURCE ESTIMATION An ore reserve estimate consists of the determination of a volume, or tonnage, and a grade for the deposit. There are numerous cases in the mining industry of projects that have experienced severe difficulties when operational ore grade, tonnage or metallurgical amenability have proven to be deficient compared to predicted estimates. An error in estimation of tonnage generally leads to more long term problems affecting mine life and production schedules. However, a significant error in the estimation of grade, particularly if mined grade is lower than anticipated, can have an immediate, and often disastrous, effect upon a project. The geologic preparation leading to an ore reserve estimate generally follows a logical sequence familiar to

Jan 1, 1987

By R. A. Jankowski

Although the number of operating longwall mining systems has remained relatively constant, longwall production levels during the last five years have increased significantly. In the United States, longwall mining now accounts for approximately 50% of all underground coal production. While longwalls are highly productive and offer other advantages, operations employing this method of mining continue to experience dust-compliance problems. This increased longwall productivity has meant that far more dust is being produced. An improved understanding of the longwall face-ventilation system and the advancement of face-ventilation technologies are necessary to ensure all face personnel are allowed to work in an environment that is free of excessive levels of airborne respirable coal mine dust. The Dust and Toxic Substances Control Branch, National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, examined several basic principles of the long wall face-ventilation system and has evaluated the effectiveness of numerous improved face-ventilation techniques for longwall mining systems. These include identifying improved techniques for measuring face-ventilation parameters on longwall mining sections and investigating the fundamental relationship between face airflow and the entrainment and dilution of respirable coal mine dust. Studies have been completed to determine the impact on face dust levels of using belt entry air to ventilate the longwall. Novel methods have been identified to increase the face air¬flow and to manage face airflow to effectively minimize dust exposure to face workers. Unique systems of auxiliary face ventilation have been developed and evaluated at full-scale, simulated longwall test facilities. The theoretical and applied aspects of each of these principles and technologies are discussed. Application of these results throughout the longwall mining industry, as documented from surveys conducted in the early 1980s and 1990s, have reduced the health hazard associated with excessive exposure to respirable coal mine dust.

Jan 1, 2000

By T. B. Whitmoyer, J. E. Sneckenberger, M. A. Jerabek, C. F. Stanley

The measurement of acoustic impedance at frequencies up to 6,400 Hz has been proposed as a diagnostic tool to yield more detailed information about lung condition. A three generation branching system of plastic Y-tubes has been constructed. The impedance of the branched system is measured by an impedance tube using the two-microphone technique. The impedance spectrum is used to calculate the reflection coefficient spectrum, which is converted to an impulse response by an inverse FFT. The area function is extracted from the impulse response by the Ware-Aki algorithm. Measurements of acoustic impedance of the branched system were made for several different end conditions of the eight terminal outlets. The outlets were either blocked with modeling clay, plastic packing material, or aluminum blocks or were unblocked. Six measurements were made of each configuration. In general, the more outlets blocked, the larger the shift to the right of the impedance magnitude peaks for frequencies above 3000 Hz. The impedance magnitude peaks for the plastic packing material were shifted in frequency to the right relative to the peaks of the other system terminations. The impedance magnitude peaks for the clay and aluminum system terminations were significantly different in magnitude but not shifted in frequency. The area functions at the end of the branched system were significantly different (a > 99%) for most of the end conditions. Area functions for the modeled branched lung systems between the end of the impedance tube and the termination outlets of the branched system were similar but distinctively different for the various end conditions. These results indicate that the two-microphone technique can sense small changes in the terminating end conditions of a rigid system of branched tubes and thus may sense impedance changes due to lung disease in the conducting airways. Keywords: acoustic impedance, lung model, area function.

Jan 1, 1991

By Anibal Gajardo

Because of the Chilean Ministry of Mining's interest in the development of industrial minerals, the Chilean Geological and Mining Service (Servicio Nacional de Geología y Minería, SERNAGEOMIN) has carried out a research program during the last two years to identify projects that represent interesting investment opportunities for small- to medium-scale operations in Chile. Most important of these projects are: (1) Quebrada Lluta aluminum sulphate, for drinking- and industrial-water treatment, with a potential domestic and foreign mar- ket of almost 43,000 tonnes per year and investments of about US$1.8 million; (2) Quebrada Lluta-Quebrada Cardones pumice, for abrasives, filters, fillers, and light- weight aggregates, with a potential market of about 30,000 tonnes per year, and in- vestments of US$2.0 million; (3) El Maule dolomite, for soil conditioner and iron smelting, with a total potential domestic market of some 60,000 tonnes per year, and estimated investments of US$2.0 million; (4) Las Escaleras bentonite, for animal feed, pelletising, and oil absorbents, with a potential market of almost 6,000 tonnes per year, and investments of about US$2.4 million; (5) Laraquete-Carampangue andalucite, for alumina refractories, with a future total domestic and foreign demand of about 15,000 tonnes per year, and estimated investments of US$2-2.5 million; (6) Rio Lía garnet, for fillers and sand-blasting abrasives, whose domestic market represents 10,000 tonnes per year, with investments of US$2.3 million; and (7) Munilque pumice, for building bricks and panels, with a potential domestic market of 250,000 tonnes per year, and investments of US$1.4 million. The development of these projects will represent an important increase and a significant diversification in Chilean industrial-minerals production.

Jan 1, 1999

Because the Environmental Protection Agency has identified methane as a greenhouse gas, the importance of de gasification through gob wells has become more critical. It has been observed that the degree of methane emission is closely related to the geomechanical characteristics of coal bearing strata, roof, floor, and surrounding coal seams. Monthly production data from 250 gob wells were collected from the Warrior Basin in Alabama, and many interesting correlations were observed between methane production with longwall face width, face advancement rate, number of gob wells in a panel, and geologic columns. Extensive finite element analyses were performed to estimate the characteristics of the emission zone in an attempt to corroborate these findings. This paper describes an investigation for developing correlations between the geomechanical behavior of the methane emission zone with methane production.

Jan 1, 1996

By A. G. Mayton, L. Adler

The paper under discussion provides an excellent and concise study of compartment ergonomics for thin seam equipment. However, in accomplishing this, some very important operational aspects were ignored. Since these are likely to be determinant, the authors' response is solicited. The novel shuttle car with its cross-car, end-mounted compartment is operationally very different from the current one. The latter can be considered a highly mobile extension of the continuous miner or loader, with a pass-through conveyor, dump boom, and extra storage. As such, the vehicle's kinematics are the simple "I," or shuttle pattern, bent for going around pillars, with an intermediate stop at the "change-out point" (Adler, 1986 ). The action of the cable reel adjusts well to this pattern. The proposed shuttle car's motion either superimposes a "Y," time is lost (5 seconds) for each cycle, space is needed, line of sight is compromised, and a cable anchor is probably required at the dump. A chute is almost prohibitive in construction time and cost. The lack of a dump boom further curtails flexibility in the proposal. The value of a standard hand and opposite standard hand configuration also needs consideration. Many front-end loaders have a rocker (overshot) capability that is designed to achieve an "I” pattern. And crawler loaders sometimes use a side dumping bucket variant for the same purpose. These examples indicate the pattern's importance. For underground, thin seam application, the ram car has become popular. This is an articulated truck, battery-powered, and with an ejector dump. Its operational patterns would be similar to the novel shuttle car, except without the loading flexibility provided by a conveyor. Since the cab location of the proposed shuttle car largely obviates some of the major advantages of the present shuttle car, the question arises whether this configuration could be adapted to the current ram car and scoop

Jan 1, 1991

By Victor J. Scaravilli

This report is based on experience developed on the construction of one contract for the Buffalo, New York subway. The Buffalo subway is under construction for the Niagara Frontier Transportation Authority and is called the LRRT-Light Rail Rapid Transit or more commonly the Metro. The Initial Route of the Buffalo subway construction started early in 1979 and is scheduled for completion in May, 1984. The initial system includes 5.2 miles of underground construction, 1.3 miles at grade for a total of 6.5 miles of subway system. A total of fourteen stations, eight underground and six at grade are included on the system. The Initial Route has a planned expansion to 17.3 miles in the future. On January 15, 1979, a Joint Venture of S & M Constructors, Inc., Solon, Ohio, James McHugh Construction Co., Chicago, Illinois, and Kenny Construction Company, Wheeling, Illinois, was awarded contract 100031, the Line Tunnels from Amherst Street to South Campus in northcentral Buffalo between Delaware Park and the State University, (see Fig. 1, Location Plan) This $35,000,000.00 contract was designed by Hatch Associates Consultants, Inc., Buffalo, N.Y. The Notice to Proceed was issued January 15, 1979 and the scheduled completion date is August 18, 1981. The project consists of two parallel rock tunnels with a minimum excavated diam of 18 ft 0 in. and a final concrete lining of 16 ft 0 in. diam. The tunnels total 14,630 linear ft. In addition to the tunnels, contract C-31 includes four shafts, an underground pump station, three cross passage connections, and other minor work items. (see Fig. 2, C-31 Project Plan and Profile) The tunnels were constructed primarily within the Bertie Formation, an approximately 50 foot thick moderately fractured to massive, dolo-

Jan 1, 1981

By L. Adler

The paper under discussion provides an excellent and concise study of compartment ergonomics for thin seam equipment. However, in accomplishing this, some very important operational aspects were ignored. Since these are likely to be determinant, the authors' response is solicited. The novel shuttle car with its cross-car, end-mounted compartment is operationally very different from the current one. The latter can be considered a highly mobile extension of the continuous miner or loader, with a pass-through conveyor, dump boom, and extra storage. As such, the vehicle's kinematics are the simple "I," or shuttle pattern, bent for going around pillars, with an intermediate stop at the "change-out point" (Adler, 1986). The action of the cable reel adjusts well to this pattern. The proposed shuttle car's motion either superimposes a "Y," time is lost (5 seconds) for each cycle, space is needed, line of sight is compromised, and a cable anchor is probably required at the dump. A chute is almost prohibitive in construction time and cost. The lack of a dump boom further curtails flexibility in the proposal. The value of a standard hand and opposite standard hand configuration also needs consideration. Many front-end loaders have a rocker (overshot) capability that is designed to achieve an "I" pattern. And crawler loaders sometimes use a side dumping bucket variant for the same purpose. These examples indicate the pattern's importance. For underground, thin seam application, the ram car has become popular. This is an articulated truck, battery-powered, and with an ejector dump. Its operational patterns would be similar to the novel shuttle car, except without the loading flexibility provided by a conveyor. Since the cab location of the proposed shuttle car largely obviates some of the major advantages of the present shuttle car, the question arises whether this configuration could be adapted to the current ram car and scoop.

Jan 1, 1990

By Joseph E. Worthington

The announcement of a high-grade ore intercept near Wenatchee, Chelan County, WA, by Asamera Minerals in 1983 triggered widespread interest in this old gold mining district. The district has a long history of exploration and production and was actually one of the few underground gold mines that operated in the post World War I1 years in the US. Gold occurs in a north-trending structural zone in folded and faulted Eocene arkose intruded by andesite and dacite dikes having dates in the 42 to 50 m.y. range. Ore has been mined selectively from ladder veins perpendicular to the trend, from the south end of the trend near Squilchuck Creek. These veins narrow and silicification becomes pervasive northerly where wider zones were caved later in the operation. Recent discoveries at "B" reef at the north end are also in wide zones of silicified arkose. The gold lodes originally cropped out as prominent silicified and iron-stained ridges that were described in the early days as "reefs." The early discoveries were made in out- crop about a hundred years ago, and two claims, the Gold King and Macbeth lodes, covering the most prominent out- crops on the north side of Squilchuck Creek, were staked in 1885 and patented shortly thereafter. A five stamp mill was erected in 1894, but failed to liberate gold for amalgamation. The two patented claims were acquired in 1934 by J. Keegan, who carried out limited exploration and shipped small amounts of flux ore to Tacoma during the next few years. There was no substantial exploration or development of the claims, however, for several years after that time, and ownership of the claims eventually passed to a series of trusts administered by a bank in Seattle.

Jan 1, 1990

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

This paper describes the scientific data acquisition, data interpretation, and sophisticated 3-dimensional modeling processes of an ongoing gas well stability research program by the National Institute for Occupational Safety and Health (NIOSH). Results from the NIOSH field instrumentation programs and the parallel 3-dimensional numerical modeling programs indicate that overburden depth, overburden geology, surface topographic relief, strata dip of the coal measure rocks, and casing cementing alternatives are the dominant factors affecting longwall-induced subsurface deformations and gas well casing stresses. Topographic relief could produce localized longwall-induced deformations if weak-to-strong rock interfaces are present near the bottom of stream valleys. Strata dip has significant impact on longwall-induced subsurface deformations. Cementing alternatives are found to have significant impacts on longwall-induced deformations and gas well casing stresses.

By P. K. Kaiser, M. Cai

When designing an efficient and effective support system for burst-prone ground, it necessary to select the most appropriate, i.e., the ‘right’ support components, including areal and reinforcement components. For this paper, it is assumed that the areal support is not the weakest link and the support performance is controlled by the rock reinforcement and holding components (bolts). We discuss the loading modes of rockbolts under static and dynamic loadings and analyze published data from laboratory and field tests. The mechanisms of energy absorption of dynamic rockbolts are presented and rockbolts are categorized based on factors such as energy absorption capacity, energy absorption rate, direct and indirect energy absorption capacities, rock mass bulking or displacement control, and shearing resistance capacity. Guidelines for selecting the ‘right’ rockbolts to build an effective rock support system for burst-prone ground are provided.

Apr 26, 2022

By W. M. Kidd, P. J. Duport

INTRODUCTION The enquiry of the Royal Commission on Health and Safety of Workers in Mines of 1976, known as the Ham Commission after its chairman, Dr. J. Ham , now president of the University of Toronto, was one of the activities surrounding the upturn in the fortunes of the Canadian uranium industry and its markets in the mid-seventies. Although the regulation and licensing of Canada's ten major mine/mill facilities employing six thousand or more uranium mines is a federal concern under the Atomic Energy Control Act, this Commission, which paid particular attention to health and safety in uranium mines, was appointed by the Province of Ontario. Further provincial enquiries in British Columbia, Saskatchewan and Newfoundland have been aimed at quantifying, reducing or eliminating the environmental and health impact of uranium production. This work has created a mosaic of provincial regulation in what is essentially a field of federal jurisdiction. Various organizations of the federal government related to its regulatory function in the uranium industry are outlined in Figure 1 showing the matrices of regulatory, advisory and research activities associated with the exploitation of Canadian uranium resources. A more detailed examination [ ] of the governmental (federal and provincial) activities, commissions, etc., in the Canadian uranium industry indicates a definite parallelism of effort, if not of scale between the two levels of government in the execution of their roles in occupational and environmental health and safety and is presented here to explain the complex stage onto which the Canadian Institute for Radiation Safety has just entered. The development of the Institute and its precursors together with current and planned research activities are described. BACKGROUND Traditionally and constitutionally, natural resource exploitation and its regulation is under provincial jurisdiction; however, the uranium industry has been under federal control since the Second World War when security measures necessitated the creation of the Atomic Energy Control Board (AECB). Health and safety aspects, in terms of inspection, compliance and environmental monitoring are performed on behalf of the AECB by provincial labour inspectors (Saskatchewan and Ontario) and Ministries of Environment. Non-radiation health and safety matters are also enforced under the federal Canada Labour Code by provincial inspectors. In support of licensing and standard-setting functions, major research programs have been initiated and expanded at both the AECB and the Canada Centre for Mineral and Energy Technology (CANMET), formerly the Mines Branch of the Federal Department of Energy, Mines and Resources). CANMET established a Mining Research Laboratory at Elliot Lake, Ontario in 1965 to conduct research and development aimed at improving production capability, providing information on the security of uranium supply and investigating the hazards of mining and their implications for the health and safety of the miners. The provincial route in assessing the costs and benefits of uranium production has attempted to be far more conclusive in nature. While some on-going studies are funded, periodic inquiries by Royal Commission have become the accepted practice. Six such inquiries have been conducted in four provinces and widely differing policies have resulted from their findings and recommendations. For example, while the government of British Columbia in the Fall of 1980 declared a seven-year moratorium on(2) uranium mining and exploration in the province, the province of Ontario's crown utility "Ontario Hydro" financed the rehabilitation of a mine/mill complex at Elliot Lake. The latter instance is not surprising considering that the final report of Ontario's "Royal Commission on Electric Power Planning",(3) concluded that nuclear energy has a continuing role to play in the expansion of Ontario Hydro.

Jan 1, 1981

By W. R. Penney, J. M. Richardson, J. Y. Oldshue

Introduction The mining industry has for years underrated the value of mixing in mineral processing unit operations. In present-day operations where leaching is playing an ever increasing role in the total profit picture, the need for good mixing is becoming more obvious. The engineer in the research laboratory and in the operations is by necessity becoming more familiar with the concepts of mixing. This section is designed to provide the engineer with mixing data and correlations sufficient to assist in the general planning of simple mixing systems.

Jan 1, 1985

By J. A. Herbst, A. E. Oblad, Y. C. Lo

The major cost in comminution is energy consumption, which can be as high as 50% of the operating cost. Improvements in plant operations have resulted in up to a 15% reduction in energy usage (kw-hr/t). These improvements have been made through the optimization of grinding efficiency and the use of expert model-based control systems. Optimization involves the determination of the levels of the critical-operating conditions that result in the most efficient breakage of ore in the mill. These optimal levels are identified through plant/laboratory test work and through computer simulation using advanced process models. Model-based expert control achieves the maximum performance from the grinding circuit by identifying the characteristics of the ore in the mill with an optimal on-line estimator. Using this information, the control system dynamically determines the operating point that will yield the optimal performance. Two industrial applications of grinding-circuit optimization and model-based control are presented to demonstrate the power of this new technology.

Jan 1, 1997