Search Documents

By P. A. Schmitz

The characteristics of gold leaching from carbonaceous matter by sodium cyanide, and sorption of gold cyanide to carbonaceous matter in autoclaved and non -autoclaved gold ore from Barrick Goldstrike Mines Inc. (BGMI), Nevada, was investigated. Much greater gold cyanide complex sorption was observed for the carbonaceous matter in high preg-robbing ores relative to the low preg-robbing ores. This observation corroborates previous reports that have attributed observed preg-robbing behavior to the carbon in the ore. Gold cyanide complex sorption was found to be reversible for carbonaceous matter from low preg-robbing ore, but was irreversible for carbonaceous matter from high preg-robbing ores. Autoclaving the ore appeared to enhance the sorptive behavior of the carbonaceous matter from both high and low preg-robbing ores.

Jan 1, 1999

By E. R. Bauer

The trend in underground room-and-pillar coal mining is to employ remote-control continuous mining machines and extended cuts, 12 m (40 ft) deep or more. This system of coal extraction, adopted by over 435 mines, can create additional worker-safety hazards. To address the ground control and worker-positioning hazards, a combination of statistical analyses and numerical modeling was conducted. Initially, the reported roof-fall incidents and fatalities were reviewed to delineate the ground-control hazards. Then, the application of the Coal Mine Roof Rating (CMRR) for estimating safe extended-cut depths was evaluated. Finally, computer modeling to predict roof displacements during extended-cut mining was completed. The paper describes the results of these studies and their impact on the safety of extended-cut mining.

Jan 1, 1999

By G. Włoch, E. Rudnik

The oxide fraction of industrial zinc ash was characterized in terms of chemical and phase composition, leaching behavior in sulfuric acid solutions, and leaching thermal effect. The waste product contained about 68 percent zinc (Zn), 7 percent chlorine (Cl), 2 percent aluminum (Al) and less than 1 percent other metals, such as iron (Fe), manganese (Mn), calcium (Ca) and silicon (Si). It consisted mainly of zinc oxide contaminated with metallic zinc and zinc hydroxide chloride. The dissolution of metals from the zinc ash was determined for solid-to-liquid ratios ranging from 100 to 500 kg/m3, acid concentrations of 10 and 20 percent, and temperatures of 20 and 40 °C. The best result — 130 g/dm3 Zn(II) at 95 percent zinc recovery — was obtained at a solid-to-liquid ratio of 200 kg/m3, sulfuric acid concentration RI SHUFHQWDQGLQLWLDOWHPSHUDWXUHRI ƒ& 7KH¿QDOVROXWLRQVZHUHFRQWDPLQDWHGPDLQO\E\0Q ,, DQG)H ,,, ions, but the presence of cadmium (Cd(II)) and lead (Pb(II)) ions enabled electrowinning of zinc of about 99 percent SXULW\DWKLJKFXUUHQWHI¿FLHQF\RI WR SHUFHQW /HDFKLQJRIWKHPDWHULDOZDVDQH[RWKHUPLFSURFHVVZLWKUHDFWLRQ heat of about 520 kJ/kg

By F. Calizaya

This study summarizes the ventilation requirements for the highly mechanized PT. Freeport Indonesia's underground mine operation in Irian Jaya, Indonesia. The deep ore zone (DOZ) is a coppergold deposit that is being developed underneath the current intermediate ore zone (IOZ) mine. One of the company's current plans is to prepare this mine for a steady ore flow of 25 kt/d (27,500 stpd) by 2003. This study includes the estimation of airflow requirements for various mining activities, the design of major intakes and returns, the determination of airway resistances and specifications of fan duties. It also includes the results of air pressure/quantity measurements in existing airways and the standards stated by the current Indonesian mining law.

Jan 1, 2000

By Justin Jensen, Luis Moya, Jose Carlos Durazo, William Szolga, Tyler McCallum, Tim Doubleday

Sulfuric acid mist is an undesired by-product of the copper electrowinning process, caused by oxygen evolution at the anode which entrains droplets of the acidic copper electrolyte solution. As the oxygen moves to the surface of the cell, these droplets become aerosolized resulting in acid mist. The addition of chemical anti-misting agents to the copper electrolyte is a common mitigation technique. This paper details Syensqo’s laboratory development of a new environmentally friendly acid mist suppressant, ACORGA® EW98. The product exhibits excellent acid mist suppression and it is fully compatible with the adjacent solvent extraction process. Lab and pilot test results are reviewed ahead of future planned industrial trial testing.

Feb 1, 2025

By Richard M. Chamberlin

Perlite is an altered rhyolitic glass with 2 to 5 wt % water that expands or "pops" when heated quickly to plasticity while evolving steam to form lightweight, glass foam. Commercial perlite deposits in New Mexico are well-developed zones of chemical weathering (hydration) superimposed on highly permeable and thick glassy zones at the chilled upper surface and toes of high-silica-rhyolite lava flows and lava domes. The maximum tonnage of glass in these volcanoes was predetermined by their unique eruptive histories. New Mexico perlite production (80% of US production of 571,00 st) is mostly from the 3.9 Ma high-silica-rhyolite lava flows at the No Agua Peaks volcanic center. The primary vent at No Agua is defined by a 900 ft-high rubidium-rich composite lava dome, known as West Peak, that contains minor perlite reserves. Slightly less rubidium-rich lava squeezed out from under the west flank of the dome to form relatively thin (250 ft) but highly vesicular lobate flows that now consist of about 50 % recoverable perlite. Finally, rubidium-poor lavas were extruded from a radial dike on the northeast flank of the dome. These thicker (400 ft) flow lobes contain about 20 % recoverable perlite. The largest mass of lava does not always contain the most perlite. The thinner (west) flow at No Agua yields the largest perlite reserves rather than the large composite lava dome or thicker (east) flow.

Jan 1, 1994

By K. L. Gabby

Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately mercury is recovered along with the silver as mercury/silver/gold amalgam which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness, while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution.

Feb 23, 2014

By R. O. Burt

The paper examines the role of gravity concentration in both an historical contest and within the modern mineral processing industry. It discusses the principles of the process on both a theoretical and practical level. The importance of ore mineralogy and its effect on the choice of the wide range of equipment available is discussed. The paper concludes with a discussion on the relative merits of gravity concentration to other forms of processing and seeks to answer the classical question - "Quo Vadis?"

Jan 1, 1982

By R. R. Bhappu

The metallurgical processing industry is in the midst of a hydrometallurgical revolution with mining companies looking for low cost, energy efficient and environmentally friendly technologies for processing sulfide ores and concentrates. The Intec Copper Process is one of the most advanced of these technologies and has the potential to greatly change the way copper concentrates are treated in the future. Specifically, the Intec process has the ability to be built on a small scale and at mine sites while being much more economic than conventional smelting. Intec Copper has constructed a I tonne of copper per day demonstration plant in Sydney, Australia designed to verify metallurgical and operational performance. This paper will describe the process in more detail and provide preliminary results of the process based on the plant's performance. It will also compare the Intec Copper Process with a few of the competing technologies and evaluate the relative economic merits of Intec.

Jan 1, 1999

Grinding and energy input in stirred media mills are studied as functions of grinding time, stirring speed, media size and density, solid concentration, impeller and tank dimensions and design, and other relevant variables. Ground product size and surface area are determined with respect to the above variables. Changes in energy input and media/pulp rheological properties during grinding are described. The best conditions for grinding limestone in the laboratory stirred media mills have been identified. Equations for correlations involving power and modified Reynolds numbers have been established.

Jan 1, 1995

By F. Stanley, A. Noble, G. Luttrell

"The supply chain for coal-fired power stations involve a multi-stage network of mining units, preparation plants, blending facilities and transportation systems. Attempts to optimize the supply chain have historically been difficult due to the lack of communication/coordination between the various groups involved in coal production, transportation and utilization. In light of this issue, a new approach for globally optimizing the coal supply chain called Micro-Price Optimization has been developed to simplify the optimization problem and to provide coal producers with fundamental insight needed to improve the profitability of their operations. This fundamental concept assigns unit values to each particles (or groups of particles) passing through production units. Optimization occurs whenever the maximum tonnage of positive value particles are recovered and passed to market, while the minimum tonnage of negative value particles are recovered. Elements considered by the concept include factors such as target boiler cost/efficiency, waste disposal costs, coal quality parameters, emission penalties, transportation charges, or other quantifiable impact factors. This article reviews the basis for the micro-price concept and provides a detailed industrial case study involving the determination of optimum coal qualities that need to be supplied by mine operators to feed a coal-fired power station. INTRODUCTION The performance of coal preparation plants have long been known to play an important role in determining the overall profitability of mining operations. This significance is due to the fact that the misplacement of just 1 ton/hr of clean coal to reject resulting from poor plant performance can represent nearly $300,000 per year in lost revenues for a mine producing a steam market coal (i.e., 1 ton/hr x $50/ton x 6,000 hr/yr = $300,000/yr). This loss can be even more pronounced, occasionally approaching $1 million per year for each 1 ton/hr of misplaced clean coal, for operations producing high-quality coking coal products sold into the premium metallurgical market (i.e., 1 ton/hr x $150/ton x 6,000 hr/yr = $900,000/yr). Detailed economic studies indicate that improvements in plant yield resulting from increases in organic efficiency have one of the largest overall impacts on mine revenue when compared to other cost centers within the mining operation. One of the first studies to show this important financial impact was reported by Norton-Hambleton Consultants (Norton, 1979). Their study indicated that an unfavorable change in plant efficiency was second only to coal transportation in terms of its impact on profitability, while an unfavorable change in the cost of underground mining was a distance third. This longstanding realization has continued to provide a strong financial incentive for coal producers to optimize the separation efficiency of their coal processing and blending operations."

Jan 1, 2015

By R. H. King

Recently, the North American mining industry experienced a severe recession, forcing managers to take dramatic steps to cut costs and compete in the difficult international market. Some of these steps were closing mines, reducing work forces, renegotiating wage agreements, and purchasing the most productive equipment. Managers are now looking beyond these traditional avenues and are focusing more on advanced technology. In the present environment, it is essential that mine operators obtain the maximum use of capital expended on equipment. However, mine workers do not obtain maximum efficiency or productivity from equipment because the adverse and hazardous mine environment impedes human performance. Also, the efficient use of large, complex machines calls for levels of precision that many times are beyond the capability of even highly trained miners. A possible solution to this problem is a machine that mines without operators - autonomous mining machines. However, numerous problems confront researchers who are attempting to develop such equipment. Some mining tasks are not always composed of a series of cyclic motions readily performed by factory floor robots. In addition, mining takes place in the geological environment where conditions are highly variable and unpredictable. As a result, these machines must be able to sense and adapt to variations in operating tasks and environment. Considerable autonomous vehicle research has been completed, especially for defense. However, autonomous vehicle (AV) technology has not advanced to practical application yet (King, 1988) and mining research is necessary in areas: representing mining specific knowledge; •analyzing and reasoning about sensor data in the mining environment; and •discovering completely new mining methods or new approaches to existing methods that become apparent when we remove the constraints imposed by the necessity of human operators. A specific machine, the LHD, can be used to show the problems for researchers who are attempting to develop autonomous machines for mining. This author chose the LHD because it can borrow concepts developed for autonomous navigation by military programs. But considerable mining research is also required. Furthermore, studies done at the Henderson mine, in Colorado, show autonomous LHD 's promise cost and safety benefits (King, 1988). At Henderson, LHDs load ore from draw points, tram to an ore pass, dump and return, or switch to another draw point. An autonomous LHD must sense vehicle position along the route, relate sensor data to stored-map information, to determine location, follow drift center lines, plan paths between dump position and initiate appropriate control commands, sense vehicle operating status and vehicle health, key on features or targets for special tasks like high speed turns, perform end of travel tasks (loading and dumping), and detect and avoid obstacles. These goals are similar to those for shuttle cars, trucks, and front-end loaders. Therefore, much of the technology is transferable. Each Henderson LHD extracts six to 40 dippers from each of a series of draw points. The LHD transports the ore to an ore pass within 55 m (180 ft) of the draw point, making the longest round trip 110 m (360 ft). The LHDs have very fast hydraulic dumping and loading systems that reduce the round trip cycle to less than one minute. Even though the LHD is capable of 500 trips per shift, the average production is 300 dippers. Man trip and lunch reduce available operating time to 6.5 hours per shift. Mucking difficulties (setting large boulders aside), operator breaks for activities like talking shop, and cleaning and smoothing roads further reduce operating time. Supervised autonomy can reduce the number of operating units by increasing operating time per shift since computer controlled machines can operate during lunch and between shifts and reduce operator errors. If dippers per shift increase from 300 to 350 (long-range goals are 500 dippers per shift), constant production requires only 10 operating LHDs and two spares. Manpower requirements drop from 24 to four by controlling five machines from one workstation. A review of technology available from the Autonomous Land Vehicle, the Advanced Ground Vehicle Technology, the Ground Surveillance Robot, and other programs, show the following differences between others work and mining industry needs: •If we focus initially on mobile haulage vehicles, we can navigate from a map. We do not need to explore. •We can modify the environment to reduce the navigation requirements. •We have a harsher environment than any of the research programs have encountered. •Our equipment must operate faster and more precisely than present AVs. •Our equipment must operate reliably over long periods of time. •We must have better onboard machine health monitoring and diagnostics. •The AV programs do not address geosensing. •The major AV programs are not cost-effective. For example, we cannot afford the computer power for robust image processing, yet. To computer control an LHD, we must replace the guidance and monitoring skills of experienced operators with sensors, computing hardware, interfaces, and several software mod¬ules. Experienced operators avoid collisions and load efficiently in piles that may contain oversize muck. Collision avoidance without an operator requires sensing all obstacles in the draw

Jan 1, 1991

By Dan Ifrim

Soft ground tunneling poses major challenges to the underground industry. Most of soft ground tunnels are in highly urbanized areas, often include limited cover, and include a strong trend of increasing diameters. Therefore, soft ground tunneling works can sometimes cause inevitable ground movements and settlements that may lead to damages to adjacent buildings, roads, structures or utilities; many of these being “lifeline” infrastructure assets. Tunneling operations, Tunnel Boring Machine (TBM) advance rates, and face pressure control can significantly increase or decrease such risks, depending on how well the TBM and operational parameters are applied to the ground conditions. Additionally, the risks of impacting existing infrastructure are heightened in many parts of North America because of cobbles and boulders. To date there is no standardized guideline that determines appropriate tunneling rates nor operator’s guidelines, to ensure safe tunnelling in soft ground. The paper analyzes tunneling records from completed soft ground tunnels to determine a relation between ground conditions, tunnel cover, TBM cutters maintenance and TBM advance rates. The records are discussed to draw several mitigation measures to be adopted during tunnelling, to reduce risks of settlements, over excavation or sinkholes.

Jun 13, 2021

By Jenna Wundrack, Evan Thibaud

The advanced cryogenic treatment is a post-manufacturing metallurgical process that involves subjecting off-theshelf materials to extremely low temperatures, significantly improving wear resistance and reliability. These case studies explore whether the claims of Enrich Bits & Tools benefit metals and their specific in-field application to drill bits in the blasting industry. This paper reviews the application of the treatment to button drill bits for enhanced wear resistance in two operations. The first is a civil construction project with highly abrasive rock. To confirm the remarkable benefits of the treatment, a second case study was performed. This case study utilized measure-while-drilling technology in consistent rock characteristics to reduce variables in the field study.

Feb 1, 2024

By A. Noble

For the past 30 years, process flowsheet design has been accomplished largely through modeling and simulation. This approach provides circuit designers the freedom to test various separation approaches while minimizing physical and human resource requirements. The Limn® software provides a unique approach to process simulation, through a Microsoft Excel interface. While the software comes with standard process models for numerous unit operations, the Excel calculation environment and the accompanying VBA platform provide a convenient interface for custom model integration, even for non-experienced programmers. This feature is especially useful for university students in introductory process modeling and simulation-assisted flowsheet design courses as well as experienced practitioners with proprietary process models. This paper shows how the Limn® software may be used to solve basic process engineering problems as well as more comprehensive circuit design challenges. Industrial examples as well as opportunities for training and education are presented.

Feb 23, 2014

By P. Amelunxen

Over the past several years, the combination of higher energy and steel costs and the recent commercial deployment of high-pressure grinding rolls (HPGR) technology in hard rock mining have led many multinational mining companies to evaluate the suitability of HPGR technology for their particular comminution circuits. HPGR technology is perceived to require a higher capital investment while delivering lower long-term operating costs. This paper undertakes a critical evaluation of this perception. By evaluating the capital and life-of-mine operating costs of competing circuit designs for soft, medium and hard ores, the HPGR break-even point can be identified, at which the incremental capital cost of an HPGR circuit is equivalent to the net present value of the projected operating cost reductions. For ores with hardness parameters above the break-even point, HPGR circuits could offer economic benefits, while for softer ores, SAG mill/ball mill/pebble crushing (SABC) circuits are likely to be more economical and energy efficient. This evaluation considers both an SABC reference circuit and a traditional stage crushing configuration. Other influential factors are also discussed.

Jan 1, 2011

By M. K. Boateng, K. Awuah-Offei

"Mining companies have started using quantitative tools, including computer models of community interaction, to gain intelligence on social risks surrounding their projects. Models of changes in community preferences regarding mining projects over time are useful for evaluating changes in project risk due to changes in the social license to operate. For example, agent-based models that use information diffusion models and social networks are useful for studying those changes due to information diffusion. However, such agent-based models are sensitive to many input parameters including the parameters of the diffusion model and the average degree of the social network. This work evaluates the sensitivity of such a model to diffusion and network model parameters (probability of imitation, probability of innovation, and average degree) using the first order and total sensitivity indices. The results show that the model is much more sensitive to the probability of imitation than the other two parameters. Thus, to reduce uncertainty surrounding the model’s predictions of community acceptance of mining, mines need to obtain accurate estimates of the probability of imitation. INTRODUCTION Mining companies have started using quantitative tools, including computer models of community interaction, to gain intelligence on social risks surrounding their projects. Models of changes in community preferences regarding mining projects over time are useful for evaluating changes in project risk due to changes in the social license to operate. For example, agent-based models that use information diffusion models and social networks are useful for studying those changes due to information diffusion. However, such agent-based models are sensitive to many input parameters including the parameters of the diffusion model and the average degree of the social network. This work evaluates the sensitivity of such a model to diffusion and network model parameters (probability of imitation, probability of innovation, and average degree) using the first order and total sensitivity indices. AGENT-BASED MODEL OF COMMUNITY ACCEPTANCE A few researchers have started using agent-based models to study mining systems (Fujiono 2011; Nakagawa et al. 2013; Bahr 2015; Boateng and Awuah-Offei 2017a, b). Nakagawa and co-workers used ABM to evaluate dynamics of a mining project’s stakeholder networks whereas Fujiono used ABM to study innovation diffusion in the mining industry. Our previous work has presented models and a framework for modeling information diffusion in a mining community and its impact on level of acceptance (a measure of SLO) of the mining project (Boateng and Awuah-Offei 2017a, b)."

Jan 1, 2018

By M. S. Klima

A 25-mm diameter dense-medium cyclone was tested to investigate the effects of geometry and operating conditions on cyclone performance when processing -150 I'm coal. The emphasis was on examining those variables (e.g., flow rate and inlet velocity) which impact the separation kinetics (specifically the number of g's and the mean retention time) and the occurrence of apparent bypass. Apparent bypass, indicated by partition curve "tails", results from the short circuiting of the feed coal to one or both of the product streams and represents a loss and/or contamination of the clean coal. This paper presents the results for this series of tests.

Jan 1, 1993

By S. Shankar

Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant. Therefore, as part of the Respirable Dust Center's ongoing research, a three part study was envisaged: study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities; study of the same in the Lake Lynn Laboratory Mine of the USBM with both airflow and walking by personnel causing re-entrainment; and mathematical modeling and computer simulation of the re-entrainment phenomenon. In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory Mine are presented. Further, the results from the wind tunnel studies are compared with the results from in-mine studies conducted at the Lake Lynn Laboratory Mine of the USBM. Comparing the results from the two studies it was observed that increasing air velocity increased the rate of re-entrainment, but increased time of exposure decreased the airborne dust concentration. Compared to same size particles, a mixture of sizes created more airborne dust concentration when re-entrained. It was also observed that contribution of airborne dust concentration due to airflow was negligible compared to the contribution due to walking.

Jan 1, 1995

The dissolution kinetics of gold in iodide solutions with oxygen in an autoclave was investigated. The leaching process was described by a gas-liquid-solid heterogeneous reaction. The effect of stirring speed, temperature, partial pressure of oxygen, and concentration of lixiviants on the overall leaching rate was investigated. It was found that the dissolution of gold was limited by a heterogeneous chemical reaction. The apparent activation energy was measured to be 34.7-54.3 kJ/mol under the conditions studied. Experimental findings were in good agreement with the kinetic model proposed.

Jan 1, 1996