Search Documents

By Francois J. E. Scholtz, Raymond J. Davidson, Peter Greenhalgh, R. Paul Riley

A 1 t/d continuous elution pilot plan is being operated by General Mining at their Grootvlei Gold Mine using the technology developed at the Anglo American Research Laboratories. Flowsheet design and plant erection was carried out by Van Eck & Lurie and completed in December 1989. Following the conclusion of six test runs designed to optimise reagent additions, it was shown that elution efficiencies of 98-99% could be achieved using reagent additions as· low as 16 kg/ton of carbon NaCN and 28 kg/ton NaOH while consistently producing eluted carbon containing less than 50 g/t gold. Significant savings were indicated when compared and power were indicated when com­pared with the traditional batch AARL, Zadra and Micron alcohol elution procedures.

Jan 1, 1990

By Sepp A. Kutschera

are gaining increased interest for over­burden removal and ore production at large open cast mines. The application of bucket wheel excavators is still tied to soft un­consolidated rocks and soils, while belt conveyors can cope with all kind of matri­als restricted only by the top grain _ size. Therefore, mode of transport and the re­quirement of down stream ore processing de­fine the materials size distribution. These requirements are usually met by primary crushing or scalping. The paper discusses general applica­ tion criteria of bucket wheel excavator with systems primary for in-pit overburden crusher removal. and It _indeapits scalper units and discusses their technical and operational features. It further com­pares the capital and operating cost struc­ture relative to the syste

Jan 1, 1992

By Dirk van Zyl

Pad construction costs can impact the overall economics of heap leach projects. Pad construction costs for single-and double-lined pads, using various designs, are listed for a typical small and large project. Double-lined pads are now more often required by regulatory agencies. Unless such designs reduce the risk of site specific contamination significantly, the extra costs cannot be justified from an economical viewpoint. Specific attention is given to the short project life (typically five years) of heap leach projects. A few numerical examples are presented to demonstrate the overall economic impacts of these costs on economic parameters.

Jan 1, 1990

By B. G. Stone

"INTRODUCTION “Sampling is the process of taking a small portion of an article such that the consistency of the portion shall be representative of the whole” (Baxter and Parks, 1939) “An orebody is a mixture of minerals in proportions that vary in different parts of the mass. As a consequence the proportion of contained metals also varies from place to place. Therefore, a single sample taken in any particular place would not contain the same proportion of metals as does the orebody as a whole except by a highly improbable coincidence. The probable error, which would be very large if only one sample were taken, decreases with the number of samples, but it never disappears completely unless the samples are so numerous and so large that their aggregate is equal to the orebody itself, in which case the orebody would be completely used up in the process of sampling. Since carrying sampling to such an extreme would defeat its own purpose, some probable error is always present in actual cases and the practical objective is to reduce this probable error to allowable limits. This means balancing the number of samples against the desired accuracy; if there are not enough samples the result is unreliable; if there are too many, the time and expense of taking them is excessive.” (McKinstry, et al., 1948). In an actual orebody, the accuracy of sampling depends not alone on the number of samples but also on proper distribution of them throughout the orebody, for it would obviously be incorrect to take all of the samples either in a rich part or a lean part. Therefore it is important to select the places in such a way that all parts of the orebody will be represented. “For those who cultivate land which is alike arid, heavy , and barren, and in which they sow seeds, do not make so great a harvest as those who cultivate a fertile and mellow soil and sow their grain in that. And since by far the greater number of miners are unskilled rather than skilled in the art, it follows that mining is a profitable occupation to very few men, and a source of loss to many more.” (Georgius Agricola page 5 Book 1 as translated by H.C. Hoover and Lou Henry Hoover, 1950)“It is evident that mining is very profitable to those who give it care and attention”"

Jan 1, 2015

By R. Benemelis

The existence of resins in some coal deposits in various parts of the world has been known for many years. These resins vary considerably in chemical structure and properties. The resin that is found in Utah coal, however, is rather unique, and has properties particularly attractive for the manufacture of printing ink mastics and adhesives. This resin is a rather dark, very high melting point, low molecular weight hydrocarbon resin. Its typical properties are shown in Table I. Its largest use by far, has been in the printing ink industry. The history of Utah coal resin is interesting, but unfortunately one of disappointment and failure.

Jan 1, 1990

By S. Makni, F. Wang, A. Rosa, B. Klein, C. Saud, R. McIvor, A. Kumar, C. Gagnon, D. Gong

In response to the Natural Resources Canada “Crush It Challenge”, Corem partnered with the University of British Columbia and led a project to develop and demonstrate the use of high-pressure grinding to replace the workhorse of the industry, wet ball milling, with high-pressure grinding. Two plant case studies, a small tonnage gold recovery operation, and a large tonnage copper recovery operation, were carried out. Plant circuit performances were compared to pilot plants operated on the same circuit feed set up to represent the novel equipment and flowsheet that was developed to produce separation circuit feed. Numerous obstacles to industrial implementation of highpressure grinding in this role which were recognized at the outset of the work were successfully addressed. In both cases, comminution equipment energy savings alone, and final stage total circuit energy savings, exceeded 60% and 50%, respectively. Downstream mineral separation performance was the same or better.

Mar 2, 2022

By Leonidio Stegmiller

Since the petroleum crisis in 1973, charcoal1 is being considered one of the most important fuel for the Brazilian consumers, mainly for pellet's producers. In replacing fuel by charcoal mixed up with ore, obviously one of the first thing to be investigated is its influence in the product's quality. Special attention has been given to the metallurgical characteristics. This paper infocus the effect of increasing dosings of charcoal to the pellet's porosity and how other physical and metallurgical characteristics will be affected accordingly. This work was carried out using two different finesses of charcoal and dosing varied from 0.5 to 2.0%.

Jan 1, 1982

By R. H. Parker, B. A. Wills, D. G. Binns

Introduction With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the fine mineral particles in these ores. Not only is this expensive, but it leads to greater losses in slimes. Gravity concentration techniques become unacceptably inefficient for particle treatment below 25 to 50 µm, and even flotation fails in the ultra-fine range. Ore from the South Crofty mine near Redruth, Cornwall, was subjected to thermal pretreatment in the hope that differential thermal expansion of the minerals would lead to intergranular cracking, and thus enhanced liberation. South Crofty ore contains about 1% tin as cassiterite associated with a complex assemblage of quartz, chlorite, tourmaline, and hema¬tite in granite and slate. Recovery of cassiterite can be as low as 70%, as overgrinding occurs during stage reduction of the material to 1 mm (primary grinding) and 180 µm (regrinding). Cassiterite is present in grain sizes ranging from submicroscopic to + 10 mm, the bulk being predominantly in the range of 50 µm to 3 mm. Experimental Flat polished sections of the ore were photographed in reflected light using a Vickers M17 microscope. The sections were then heated in a Carbolite LMF4 muffle furnace. The heating rate and temperature were monitored by a thermocouple immersed in the bed of particles. Previous work by Sherring (1981) on the same material showed that a 55% reduction in grinding resistance occurred when the material was rapidly heated and cooled through the quartz inversion tem¬perature (573°C), where a volumetric expansion of 0.86% occurs. The samples were therefore heated to 650°C at 26°/min, and were then water-quenched to room temperature. The effect of heat treatment on the mineralogy and fracture network was assessed by examining the same area after treatment. Results Most of the sections examined showed that extensive transgranular cracking occurred as a result of heat treatment. Such cracking, although weakening the rock and hence reducing the work index, would in no way enhance the liberation of the cassiterite from the host minerals. Intergranular cracking, which would lead to enhanced liberation, was difficult to discern under reflected light, but there was evidence of such cracking in some of the sections examined. Figures 1 and 2 are examples of typical sections before and after heat treatment. Figures la and lb - show cassiterite in hematite, Fig. lb, in normal incident illumination, illustrating clearly that after heat treatment, transgranular fracture is evident in the cassiterite. If any intergranular cracking has occurred, it is not evident in this photograph. Figures 2a and 2b show cassiterite in quartz before and after treatment. Fracturing in both minerals after treatment can clearly be seen, and there is evidence of intergranular fracturing. However, protruding "arms" of cassiterite are severed by transgranular fracture. Subgrains of quartz have also been isolated by trans¬granular fracture. There is major transgranular cracking across the wider sections of cassiterite. Discussion The effect of rapidly heating South Crofty tin ore to 650°C, followed by water-quenching to room temperature, has been studied by observing the fracture networks in mineral grains. The choice of 650°C as the heating temperature was influenced by the work of Sherring (1981), who found considerable reduction in grinding resistance after thermal pretreatment of the same ore. Scheding et al. (1981), however, have shown, by means of a crude calculation, that heat treatment cannot be justified solely on the basis of reduced grinding costs. The cost of heat treatment far out-weighs that of grinding, resulting in the combined costs for heat treatment being over six times that for grinding unheated material. The most economically attractive aspect of heat treatment is the possibility of enhanced liberation of the valuable mineral due to increased intergranular rather than transgranular fracture. Grinding costs would be greatly reduced by improved liberation at coarser sizes, and the costs of ancillary processes, such as dewatering and tailings disposal, would be reduced. The most significant economic effect, however, would be in improved metallurgical efficiency. Improved liberation would increase concentrate grades, and recoveries would be higher, particularly in the case of ores where high slime losses are produced due to the excessively fine grinding required to produce adequate liberation. Manser (1983) has shown that only a 1% increase in tin recovery, at the same concentrate grade, would be sufficient to offset heat treatment costs on South Crofty ore. Heavy liquid analysis and shaking table separation have been used to evaluate the effect of thermal treatment on processing (Binns, 1984; Scheding, 1981; Sherring, 1981). However, treatment of unheated and heated samples of South Crofty ore, ground to the same product size, by such methods have shown little evidence of improved metallurgical efficiency after thermal pretreatment. The large amount of transgranular fracturing revealed by reflected light studies helps to explain this lack of improvement. Nevertheless, from the evidence of some of the fracture work, it is surprising that no improvements in metallurgical

Jan 1, 1988

By R. Mensah-Biney

The kinetics of gold-bromide loading onto activated carbon has been investigated in a batch stirred reactor. The amount of gold adsorbed by the carbon was correlated with time based on a second-order equation. The rate constant for gold-bromide species onto activated carbon ranged from 0.27 to 1.2 x 10-3 (kg/t)-l(min)-l from a solution containing 25 ppm of Au, with 0.8 g carbon per liter of solution at 30° C. The equilibrium saturation capacity (Q.) was 36±3.0 kg/t from the same system. The rate of loading increased with decreasing particle size, decreasing pH, increasing temperature, and decreasing concentration of gold in solution. The calculated activation energy E. was 8.8 kcal/mole, significantly higher than those reported for physical adsorption. The equilibrium saturation capacity (Q.) increased with increasing concentration of gold in solution, but was independent of other variables such as temperature, agitation speed, particle size and pH. These rate constants and equilibrium saturation capacity for the gold-bromide species are higher than those reported for the gold-cyanide systems.

Jan 1, 1996

By A. L. Mular

Se revisan brevemente varios procedimientos para el cálculo de coste de capital; no obstante, se discute en preferencia el método del factor estimado. Se proporciona una tabla de costes frente a los datos de parámetros de equipo, de donde los costes pueden ser adaptados a partir de los valores actuales de los índices de costes M&S para minería y molienda. Las ecuaciones de costes son utiles para preparar los programas de computador que realizan cálculos de coste de capital. Se ilustra la utilización del metodo del factor estimado.

Jan 1, 1982

By P. Gelfi, J. Vanderbeek, J. Enriquez

"The Cerro Verde copper-molybdenum mining complex is located near Arequipa, Peru. A 108,000 t/d copper concentrator (C1 concentrator) commenced operation in late 2006 and was debottlenecked to a 120,000 t/d capacity in 2011. A feasibility study, initiated in May 2010, assessed the potential for expanding the processing rate of the large Cerro Verde sulfide reserve via the installation of a second, stand-alone, concentrator (C2 concentrator) capable of processing a nominal 240,000 t/d ore. The feasibility study was successful and the project advanced through engineering, permitting and construction. Ramp up to nameplate capacity was ahead of schedule. The overall project was completed on schedule and within budget. The details of the project and supporting components are described. The design philosophy and design basis of the concentrator facilities are discussed as are factors that influenced the concentrator layout. Risk mitigation features included in the design are reviewed. The factors that drove the successful and rapid ramp up to nameplate capacity are discussed. Operational experiences in the first year of plant operation and project lessons learned are described. INTRODUCTION/BACKGROUND Sociedad Minera Cerro Verde S.A.A. (SMCV) operates a copper mine near Arequipa in southern Peru. Small scale operations operated intermittently until 1970 when the deposit reverted to the ownership of Minero Perú S.A (Peruvian government). Minero Perú S.A. commenced mining and processing of oxide reserves in 1972 and placed an SX-EW plant into production in 1976. The ownership of the property has changed hands several times over the years. Minero Perú sold Cerro Verde to Cyprus Climax Metals in 1994. Cyprus was acquired by Phelps Dodge in 1999. Freeport-McMoRan (FCX) acquired Phelps Dodge in 2007. Several studies were undertaken during the 1990’s that tried to establish the economic justification to process the large primary sulfide resource that underlies the surface oxide deposit. None of these studies produced an economic conclusion until a feasibility study was completed by Phelps Dodge and SMCV in 2004. This study provided the economic justification for the construction of a 108,000 t/d concentrator during 2005 and 2006. The key to the success of this study was identifying a water source that was sufficient to support processing economies of scale. Concentrator operations commenced in late 2006. The original design production rate of 108,000 t/d was achieved on a 30 day moving average basis on the 266th day after ore was first introduced. During 2009, studies and evaluations were performed that had the objective of addressing observed concentrator bottlenecks to allow a production rate of 120,000 t/d to be achieved. The 120,000 t/d figure represents the sustainable production limits associated with the installed primary crusher and tailing thickeners which would have been prohibitively expensive to upgrade. Debottlenecking activities were implemented during 2010 allowing sustained production rates of 120,000 t/d to be achieved."

Jan 1, 2017

By J. Carr

Ring gear and pinions used as the final drive on large metallurgical grinding mills are expected to transmit their rated horsepower reliably for long periods of time. Duty is 24 hrs./ day. Life expectancy of such gear sets is of the order of 20 years; that is, each gear and pinion flank is expected to resist failure by pitting for 10 years. This means that for a dual pinion gear set having a ratio of 18.42:1.0 and a mill speed of 10 RPM, every gear tooth will see 105.12 x 106 surface contact stress cycles and every pinion tooth will see 968.15 x 106 surface contact stress cycles in a 10 year period. The allowable surface contact stress on the gear and pinion is determined by the material hardnesses. The rule being the higher the hardness, the higher the allowable surface contact stress may be.

Jan 1, 1985

By C. G. Anderson

The treatment of concentrates for the recovery of the precious metals imposes many processing and environmental challenges. Hydrometallurgical technology for recovery of values from refractory precious metal materials has been developed at Sunshine Mining and Refining Company. Historically, conventional pyrometallurgical methods have been used for to recover values from refractory precious metal materials. However, enhanced environmental awareness has worked to constrain typical refractory material processing methods. This hinders and limits the ability of established smelting or roasting technologies to fill the needs of new sources of refractory materials. An alternative is to treat refractory precious metal bearing materials by hydro metallurgical techniques. These methods are considered more environmentally appropriate since they do not produce gaseous pollutants like sulfur dioxide. Industrially, Sunshine Mining and Refining Company employs hydrometallurgical technology to process refractory precious metal materials. The Sunshine antimony leach uses a mixture of sulfur and caustic under ambient pressure and boiling conditions. The Sunshine oxidation leach uses a mixture of sulfuric acid and a minimal amount of sodium nitrite under relatively mild oxygen pressure and temperature conditions. These conditions result in a nitrogen species catalyzed sulfuric acid pressure leach. Since hydrometallurgical technologies provide industrially proven processing options for many types of refractory precious metal containing materials, their usage should be considered. Ample work has been conducted to prove the effectiveness of Sunshine refractory processing technologies on various materials. This has included platinum group metal materials, refractory gold concentrates, silver materials and indium materials. In some cases, complete process flowsheets have been designed to recover both base and precious metals from these materials and to treat the generated waste streams in environmentally sound manners.

Jan 1, 1996

By M. S. Klima

Tests were conducted to investigate the potential for recovering anthracite from preparation plant tailings. Samples were collected from tailings streams or slurry ponds of several anthracite cleaning plants. A washability analysis was conducted on each sample. The use of gravity-and surface-based cleaning processes for treating the 28x200 mesh tailings material was examined. Simulations were performed for various cyclone staging arrangements using published partition data for both water-only and dense-medium cyclones. Froth flotation testing was done on both precleaned anthracite and tailings material. Grade-yield curves were determined for various conditions.

Jan 1, 1995

By M. S. Prasad

This paper presents the process methods of beneficiating various copper-cobalt and copper-zinc ores mined by Gecamines in Zaire. Geology and mineralization of both sedimentary and vein type deposits are described with special emphasis on the production of oxide, dolomitic and sulfide concentrates. Description of different types of concentrators and their treatment methods are discussed for the production of sulfide, oxide and dolomitic concentrates. Production of concentrates, their consumption and stocks are briefly reviewed. Modernization of the concentrators with substantial investments on grinding, classification, flotation methods and tailings treatments are also discussed to improve the metallurgical efficiency of the concentrators with a view to improve the production of concentrates both qualitatively and quantitatively.

Jan 1, 1990

By Donald E. Zipperian

It has been recognized that froth flotation of mineral particles utilizing rising flow of micro size air bubbles, counter-current to quiescent falling flow of particles in a column type cell, provides a unique mechanical atmosphere conducive to extension of froth flotation process to much coarser and finer particles sizes than possible with mechanically agitated and aerated cells. 1,2,3,4. This paper describes metallurgical results obtained at several plant installations of large capacity commercial size Deister FLOTAIRE® Column Flotation Cells. These cells utilize air aspiration into surface tension lowered water to generate micro size bubbles. Operating costs, power, wear, and scaling characteristics of rougher, cleaner, and scavenger units are compared with mechanical units. Problems encountered and scale up criteria developed when increasing from 0.20m(8inch) diameter pilot cells to 2.42m(96inch) commercial cells are discussed.

Jan 1, 1985

By J. F. Cornelsen

Wheel loaders are currently being used in many mining applications for a variety of reasons. While they sometimes provide the lowest loading cost, a primary advantage of the wheel loader versus other loading systems is the increased versatility and mobility inherent in a wheeled vehicle. The advent of large wheel loaders with much greater digging capability enhanced wheel loader usage in severe loading applications. To match these severe conditions, machines offered today were designed to work in these rocky conditions. Soon after the introduction of large wheel loaders into rocky conditions, however, it became apparent to many users that tire costs could at times account for up to 50% of total hourly operating costs on large wheel loaders. In some applications, tire costs alone pushed wheel loader economics beyond the economic feasibility for these jobs, prohibiting their use. In an effort to combat high tire costs, several attempts have been made to put fast moving steel around the tires to provide a strong interface between vehicle and ground. Some earlier attempts involved wrapping tracks around tires. Mechanical difficulties with these systems limited their customer acceptance. Subsequently, the development of protective tire chains came into favor. While tire chains offered added protection to the tires, the cost and maintenance of the chains remains a problem in 1972, the Dystred arrangement was announced for usage on a 6 cu yd wheel loader from Caterpillar Tractor Co. (See Figure 1). The Dystred offered the advantages of greatly increased tread life over conventional tires, as well as resistance to tread puncture in most situations. The arrangement basically employed a track system similar to that used on track type loaders. Pin and bushing wear often caused high hourly operating costs and excessive machine downtime. In addition, the connection of shoes through the use of links, pins, and bushings forced a limitation on too speed of the vehicle.

Jan 1, 1976

By P. W. King

The performance of the versatile McNally Wedag horizontal vibratory centrifuge for dewatering ultra fine 0.5 x 0.15 mm (28 x 100 mesh) material has proven to be success¬ful and the results presented herein will examine its capabilities in terms of capacity, solids capture, product moisture, effluent solids, and size analysis. Centrifugal dewatering of fine refuse has proven t to be another application for which this unit has performed exceptionally well.

Jan 1, 1985

By Haydn H. Murray

This paper presents the results of test work performed with a Pacific Electric Motors (PEM) high intensity magnetic separator (20 kilogauss) , a unit capable of separating weakly, as well as strongly, magnetic minerals in the particle size range of sands to clays. Tests were performed on some 40 industrial minerals. With some minerals excellent separations were attained and with others intermediate and poor separations were accomplished. This study is a preliminary survey and many of the intermediate and poor results can be improved as separation problems are worked out with additional test work. It is demonstrated that with a number of industrial minerals high intensity magnetic separation is a viable beneficiation technique that is economic ally feasible.

Jan 1, 1976

The viability of physico-chemical purification methods such as selective flocculation for separation of two components having similar chemical composition and same crystal structure but different surface properties is demonstrated. Loss of selectivity was observed in a dolomite-dolomite mixture with Polyethylene Oxide (5 million molecular weight) as the flocculant. Hetero-flocculation was minimized using a low molecular weight PEO (MW -105) as the site blocking agent (SBA). Near complete separation was achieved at pH 10.5 at 100% recovery level.

Jan 1, 1993