Search Documents

By L. F. Engle

There continues to be a certain magic attached to the word "Automation". When properly planned for, engineered, installed, and operated, the magic truly does take place - witness certain publicized mineral processing, metallurgical, and chemical plants. They operate successfully with few people, instead of previous dozens as in similar facilities not automated. Production quality has improved. Maintenance costs have been lowered. When such welcome results are achieved, it's proved to be a function of method and procedure in establishing criteria for choosing the intelligence and control systems followed by skilled choice of the specific elements used. The criteria, the bases for decision, are associated with design, construction, startup, operations, and maintenance. How to go about automating any process system to achieve the optimum profit depends on attention to all those aspects of a project. None of them can be forgotten if maximum satisfaction is to be gained. Control loops that look wonderful on an equipment. Piping, and Instrumentation diagram can suddenly turn into costly and. annoying problems in the field if there has been too little coordination of design. Panel boards that are literally works of art just before startup can become the largest of white elephants if an air header is inadequately sized and the pneumatic control circuits are sluggish. Conveyor belt replacement costs can skyrocket if a critical discharge chute far away from immediate operator attention lacks a simple yet effective clog-chute switch. Planning, execution, and followup of the work, the skills, and function of-the automating material can make any new project a success. An integrated owner contractor, producer-engineer approach is the key.

Jan 1, 1963

By D. Leppert

Clinoptilolite zeolite may offer attractive, cost-effective alternatives for remedial cleanup of old minesites, smelters and other sites with heavy metal contamination. Previous research demonstrates the relatively strong affinity of clinoptilolite for numerous metals and clinoptilolite displays a particularly strong affinity for lead (Loizidou and Townsend, 1987), one of the most toxic and problematic heavy metals. Since clinoptilolite can also selectively absorb some radionuclides and organic compounds, it may offer practical solutions to a wide variety of environmental problems.

Jan 1, 1989

By R. W. Lai

Cyclic voltammetry (CV), flotation response, evolved-gas analysis (EGA), and X-ray photoelectron spectroscopy (XPS) were employed to evaluate the major differences in the surface property and surface reactivity of coal pyrite and mineral pyrite.

Jan 1, 1989

By James K. Kindig

Hazen Research, Inc., has developed a new process for removing pyritic sulfur and ash from coal. Feed coal is contacted with iron carbonyl vapors, Fe(CO)5, at 190°C which puts a thin skin of magnetic material on the pyrite and ash, but does not affect the coal. Thus, low intensity magnetic separators yield a nonmagnetic coal, low in sulfur and ash, and a magnetic refuse, high in sulfur and ash. Results are given for clean coal produced by this method. A comparison is made between results of the magnetic process and the U. S. Bureau of Mines two-stage flotation process cleaning identical samples of Pittsburgh Coal. Capital and operating costs of the two cleaning methods are discussed.

Jan 1, 1976

By John F. Slonaker

This report is a review of current research being conducted in the United States which is intended to increase the utilization of coal ash. In order that this report be as timely as possible, the majority of information was obtained by direct comunication with the people listed in the references. Due to the magnitude of the flyash research program, some projects may be inadvertently omitted. Field research on flyash for use as an agricultural fertilizer is being monitored at Virginia Polytechnic Institute and State University.1 This research is directed at determining the plant nutrients that are available in flyash as well as the quantities of flyash that can be applied to agricultural soil without adversely affecting plant growth, Coal mine spoil and refuse bank reclamation with power plant flyash is being demonstrated by United States Bureau of Mines, Morgantown, West Virginia.2 Numerous highly visible coal refuse piles and strip mine spoil banks contribute to air, water, and land environmental problems. Revegetation of several experimental sites with flyash from bituminous coal-fired power plants was undertaken in West Virginia and Pennsylvania. Conventional farm equipment was used at some of the sites while large earthmovers were required at others. The flyash served as a neutralizing agent, dilutent, and soil amendment to provide some nutrients which enhanced vegetation of the barren areas, Estimated cost of reclamation by this method is $300.00 per acre of previously leveled area. This figure can vary considerably depending upon the topography of the site, haul distance, quality of the soil and quality of flyash.

Jan 1, 1974

By PAITIP THIRAVETYAN, KANJANA KUDPENG

The aim of this study is to compare amino acids and organic acids in the extraction of gold from silicate ore. Amino acids were found to have higher efficiency of gold extraction than organic acids at the same acid concentration, which is likely due to amino acids having both carboxylic and amine groups in their structure, while organic acids only have carboxylic groups. Five amino acids (glycine, aspartic acid, glutamic acid, lysine and tryptophan) and seven organic acids (citric, malic, tataric, fumaric, oxalic, succinic and ascorbic acids) were selected to investigate gold extraction efficiency. Aspartic acid was found to have greater capacity to extract gold than succinic acid. The optimal gold to aspartic acid molar ratio was 1:6, and low concentrations of aspartic acid extracted 35 to 42 percent of gold from silicate ore within 15 days. Further studies are needed to increase gold leaching and reduce incubation time. The results imply that aspartic acid can be used as an alternative reagent to traditional methods for extracting gold from ore. This method is nontoxic to humans, is environmentally friendly and can have real applications.

By I. H. Gundiler

A pilot-plant flotation concentrate containing 21.6 g/t gold and 2 kg/t silver was used for this study. Base-line cyanide and thiourea tests showed 30-40% extraction of both gold and silver. After roasting (450-750C), the maximum gold extracted was 89% with thiourea and 76% with cyanide. Pressure oxidation tests were conducted following a statistical experimental design in a 2L laboratory autoclave at 10% pulp density, and the residues were subsequently leached in acidic thiourea solutions for 2h. Leach results were presented in the form of contour maps, and optimum autoclave conditions were determined for maximum gold extraction (93%). However, silver extraction was only 7% when gold extraction was maximized.

Jan 1, 1992

By Nikhil Dhawan, SHAILA MIR

Consumer preference for ever-higher laptop performance coupled with laptops’ declining lifespans make them a significant contributor to electronic waste. An in-depth evaluation of elemental composition and distribution is important for determining metal recovery potential and sustainable recovery processes. In this work, the characterization of individual components of laptops is studied for the systematic identification of important elements and for streamlined and structured recycling, to reduce processing steps and improve economics. A process flowsheet highlighting various recycling routes by targeting metals and various components is also proposed.

By PEILIN LAN, LEONARD HILL, SIMON TIMBILLAH, BERNARD FOSU, CESAR SOSA-BLANCO

The use of sodium hydrosulfide (NaHS) in most of the operations in byproduct molybdenum flotation comes with safety concerns and, in some instances, a high reagent cost. Engineered solutions at the various operations where NaHS is used have immensely reduced the possibility of hydrogen sulfide (H2S) gas evolution. However, the threat of exposure remains, and this, coupled with the high dosages of NaHS consumed, supports the continued search for alternative depressants. This paper focuses on efforts to study the applicability of disodium carboxymethyl trithiocarbonate (DCMT), an organic depressant, as an alternative to NaHS. Bench-scale rougher flotation results for samples from the Sierrita copper–molybdenum (Cu–Mo) plant showed the best DCMT performance at 8 kg/t of DCMT, pH 10.5, 30 min of shear conditioning and 10 min of flotation conditioning. The Aminpro plant model simulation confirmed that 4 to 8 kg/t DCMT under certain shearing and conditioning times achieved superior or equivalent Mo–Cu separation efficiencies when compared\ to NaHS.

By Barbara B. Newlin, Emily Rosenberg, Marianne Snedeker

Whose longwalls perform best in Eastern underground mines? What is the latest legislation affecting slurry pipelines? What are the trace element constraints on magma genesis? How can process set points be controlled more economically without affecting product quality? Where can I get a paper presented at the Australian Coal Preparation Conference? If answers to questions like these can help with your management decisions, exploration plans, or market positioning, your firm should know about Information on Demand. Information on Demand, Inc. (IOD) is a research service available to SME members to help them get the facts needed to develop business plans. IOD can function as a research staff and data bank specialist for geologists, planning specialists, production managers, and engineers in all levels of the mining industry. Just dial 415-549-3259 and ask IOD for a copy of an obscure article, a comprehensive literature search, or a background report on a company, a process, or a product. Within a short time, IOD will have the information you need delivered to your office or worksite. Information on Demand has a bank of dial-up terminals that provide access to more than 200 business and technical data bases, including Lockheed's Dialog, CompuServe, InfoLine, The New York Times Information Bank, and other systems. These data banks contain more than 95% of the world's technical literature published in the last 10 years. There is no input required from individuals or companies. The data bases are maintained by publishers and are constantly updated with abstracts of articles, reports and reviews, and other text appearing in more than 5,000 engineering publications, as well as thousands of other trade and technical publications. The data bases are organized by subject and offer a speedy comprehensive survey of world literature. One data base, called Compendex, provides worldwide coverage of engineering publications, meetings, and reports. The Metadex data base abstracts literature on the science and practice of metallurgy, and can be accessed by commercial, compositional, and numerical alloy designations. PatSearch and Claims data bases enable IOD to determine what patents have been filed by a given entity, what international patents are equivalent to a US patent, and other vital patent information. In the non-technical arena, the Commerce Business Daily has daily updates of federal procurement information. The Federal Register is abstracted on-line in a data base, and ABI/Inform is a data base full of marketing and management information for all industries. IOD offers a free pamphlet listing these and other data bases. A typical literature search from IOD will produce 60-200 references with abstracts, and can be printed out off-line and mailed or transmitted directly to an electronic mailbox. Abstracts will often give all the information needed by the reader. At times, when the complete article or technical report is needed for further study, IOD will send a photocopy of the full text for a small additional fee. Patents, books, securities exchange filings, standards, and specifications can also be supplied by means of IOD's network in major libraries, such as Harvard, MIT, and The Library of Congress. A technical translation service is available for foreign

Jan 12, 1983

By Howard N. Egan

The importance of coal as the major energy source has led to wider interest in the recovery of waste coal fines as a usable product. An additional incentive for fine coal recovery has been the increased emphasis on environ- mental pollution control and conservation of the nation's natural resources, Accordingly, a series of studies and tests were performed to investigate the feasibility of the recovery, concentration, balling and pelletizing of coal fines as a marketable adjunct to existing mining and beneficiation operations. These studies were conducted at the existing operations of the Eastern Coal Corporation at Stone, Kentucky, and the Metallurgical Laboratory of Arthur G. McKee & Company in Cleveland, Ohio. The purpose of the investigations was to recover the fines from the effluent waste waters of an existing preparation plant and transform them into a high carbon, low sulfur and ash product capable of being handled with a minimum of degradation and dusting problems. The fines were relatively high in ash content prior to processing, and flotation pretreatment served a combined function of beneficiation, recovery and water clarification, The minus 28 mesh coal concentrate containing 40 to 45 percent minus 325 mesh size material had an ash content varying between 5 and 7 percent and a sulfur content of less than 0.5 percent. Chemical and size analyses of the effluent and concentrated fines are presented in Table I for comparison.

Jan 1, 1967

By M. J. Carlson

With the goal of improving the strength characteristics of pneumatically emplaced material used for localized subsidence control, the binding additives: fly ash, bentonite, and Portland Cement, were examined for their effect on the support capabilities of coal refuse. It was found that, within certain concentration ranges, all three of them offered some increase in the ultimate strength of the backfilling mixture; however, Portland Cement gave the greatest percentage increases. Selection of the appropriate backfilling mixture will allow for the most economical and efficient subsidence control when pneumatic stowing is employed.

Jan 1, 1987

By B. P. Boisen

INTRODUCTION The rapidity of onset, rate of increase, and magni¬tude of loads in an underground support system can be measured using load cells or pressure cells, whichever is appropriate to the type of support. These instruments should be installed at the various instrumented station locations immediately after excavation. If the loading of a member is of interest, the load should be measured, whereas if the deflection or strain of a member is of interest, the strain should be mea¬sured. It makes as little sense to use a load cell to allow computation of strain as it does to measure the strain and then back calculate the load. Tunnel steel set de¬signers today invariably rely on the early work of Karl Terzaghi, the basis for which is load, so load measure¬ment should be the main concern. The current trend of using strain gages on steel sup¬port systems stems from the inability by some to eval¬uate unusual loading conditions caused by uneven block¬ing. In fact, uneven blocking will obscure almost any attempt (whether with load cells or strain gages) to properly evaluate support performance. The load curve in Fig. I shows the development of a characteristic early peak load sometimes called the "rear abutment load" seen in many underground open¬ings. It is thought that the peak reflects the coupling of the rock and the support system, and that the magnitude will increase until some yielding, or minor failure, of the support system occurs. At that time, the slight deforma¬tion of the support system promotes the formation of minute shears in the opening walls, and these shears tend to distribute stress between the support system and the adjacent rock in proportion to the relative rigidity of the support elements and the rock. In normal rock, as a result of this stress redistribu¬tion, subsequent load magnitudes generally do not reach the magnitude of the early peak load. In physically unstable (squeezing) or chemically un¬stable (swelling) rock, however, the loads experienced after passage of the early peak load may in fact show a slow, continuous increase. One of the very important purposes of load instrumentation is to provide the means for recognizing such long-term adverse trends, thus enabling the proper remedial steps to be taken. Another purpose of load instrumentation is to pro¬vide a comparison between the magnitudes of the early peak load and the subsequent stable load. The ratio of these two loads is analogous to a safety factor, and may be used to evaluate the efficiency and economy of the support system design. Aside from considerations of economy, it may be well to design support systems which do not have excessively high ratios of early peak load to subsequent stable load. Should these ratios be exces¬sively high, the support system may be so rigid that the yield or failure associated with stress redistribution may occur with explosive violence. Load cells for use in mines, tunnels, and on con¬struction projects come in many forms. Almost all, however, employ the same procedures for installation, readout, etc. Therefore the following comments are almost universal in application. LOAD CELL INSTALLATION Load cells should be installed with bases parallel to the surfaces against which they bear. Care must be taken to orient the cells so that their signal cables are protected from accidental damage as a result of con¬struction, maintenance, or cleanup activities. Most electronic load cells are compensated for tem¬perature variations likely to be encountered during nor¬mal operations. However, if a large difference is an¬ticipated between the calibration temperature [21°C (70°F)] and the average operating temperature, the cells should be conditioned to the operating temperature for at least 8 hr prior to installation. This is to insure that the initial reading, made under no-load conditions prior to installation, provides a stable value to which subse¬quent measurements can be referred. Hydraulic load cells tend to be temperature sensitive and should be used with that in mind. Also, hydraulic load cells tend to be soft compared to electronic types and will sometimes allow movement to take place in a system intended to be semirigid. Furthermore, hydrau¬lic load cells tend to be difficult to read remotely. Care must be taken to use bearing plates on both sides of load cells which are sufficiently rigid and of high enough bearing capacity to prevent bending and crush¬ing under load. This is very important with tieback load cells (basically a ring of steel) which can easily dig into bearing plates. MAINTENANCE AND TROUBLESHOOTING Except for a direct hit by a miner's axe or flyrock from a blast, most hydraulic load cells are nearly in¬destructible and require little, if any, maintenance. Hy¬draulic oil on the bearing plates is a good indication of a leak and the need for corrective action. Field maintenance of electronic load cells involves protecting the instrument and signal cable from mechani¬cal damage and from unnecessary exposure to dirt and moisture, and recognizing and correcting damage and the effects of normal wear and tear.

Jan 1, 1982

By NILAMADHABA SAHU, Gajanan U. Kapure, Pankaj Kumar, Sunil Kumar Tripathy

Chromite ore processing tailings and low-grade manganese ores are typically considered waste due to their limited or negligible utility, leading to environmental and storage concerns. Researchers globally have explored various methods to utilize or upgrade these wastes, particularly because dumping chromite ore has been linked to severe health issues through Cr(VI) leaching. Individually, these ores lack economic value, and there has not been research on simultaneously reducing both low-grade ores. In this study, the focus lies on smelting these ores together, aiming to create a precursor alloy for 200 series stainless steel scrap. Initial research indicates the potential for scrap formation, validated through laboratory experiments with varying coke rate, basicity and holding time. The investigation discovered that smelting this combination could yield a metal product consisting of 59 percent Fe, 24.93 percent Cr, 7.56 percent Mn, 0.62 percent Ni and 0.93 percent Si. The optimum basicity was found to be 0.6 with 80 percent recovery. Notably, this process eliminates intermediate steps in 200 series stainless steel production, potentially reducing overall carbon dioxide emissions. This proposed method represents a cleaner, sustainable approach to repurpose these two waste ores, projecting a net profit of US$330/t.

May 1, 2024

By S. Rideout

The United States Department of the Interior's Office of Surface Mining (OSM) is responsible for regulating active coal mining and reclaiming abandoned coal mines in the United States. In working with the State government agencies that implement these programs, OSM is building a new approach that moves away from traditional "command and control" regulation and towards an approach that focuses on providing long-term environmental and economic sustainability on lands disturbed by coal mining. This initiative called "Reclaim the Future!" looks to enhance opportunities for economic development, wildlife preservation and enhancement, reforestation, and other beneficial and productive uses of lands disturbed by coal mining. The initiative is also focused on ensuring that the landowners and the local public have significant involvement in determining how best to reclaim mine sites and what post-mining land uses are most appropriate for each individual abandoned mine reclamation project or active mine reclamation. Through the use of the best scientific input in an open, participatory process, OSM hopes to further sustainable development principles for coal mining within the framework of existing United States law.

Jan 1, 2007

By Scott G. Britton

Planning is a management tool used to solve problems and provide data and decision alternatives for company growth, profitability, and direction. Strategic planning is defined as the efforts needed to accurately measure the risks of obtaining a result from future actions given a finite number of outcomes. The techniques of strategic planning are being applied more and more to underground mine design as a result of the fierce market conditions underwhich the industry is facing today, and the conditions they will likely face in the future. The objectives of strategic planning are centered on the ability of the operator or company to manuever its limited resources to the best position available under the given future scenarios. This paper briefly examines the most popular techniques for accomplishing these objectives, how these techniques fit into the current mine management decision-making, and what results to expect from these techniques in planning efficient underground mines.

Jan 1, 1985

By J. L. Thompson

The combustion of pulverized coal is a century-old practice. Many people have investigated coal dust and the residual fly ash particles that re-main after combustion. But the combustion process and fly ash formation mechanism are not under-stood. Working at our Maysville, Kentucky lime plant, the Dravo Lime Company Research team has collected samples of partially burned coal dust from the flame of a pulverized coal burner. Specimens were placed in a scanning electron microscope (SEM) equipped with an energy dispersive spectrometer (EDS). Microscopic examination of the particles, together with a large collection of micrographs of lime dust fused to fly ash particles, now make it possible to theorize as to how combustion advances through a piece of coal dust. Coal is a physical mixture of carbon-based compounds interspersed with bits of ash-forming materials, primarily alumina-silicate compounds. The alumina-silicate materials are commonly in angular nodules measuring 100 A to 700 A across their major dimension. It would appear that if the coal particle is in a well mixed gas stream, combustion starts at the surface and advances radially toward the particle center. With poor gas mixing, it is common that combustion moves from one end of a particle and advances on a broad front almost normal to some axis. In either case the combustion process and ash-forming mechanism are the same. As combustion occurs the carbon-based compounds oxidize in a highly exothermic reaction. Heat from the re-action melts the alumina-silicate nodules causing them to flow together and coalesce into an open sponge-like structure. As melting continues surface tension of the liquid and free surface energy causes the sponge-like structure to simplify into fewer, larger pores. Most likely the lighter molecular weight hydro-carbons burn before the heavier species. This means that as the melting ash structure is metamorphosing to a single large pore, there continues to be out-gasing throughout the structure due to combustion. Surface tension will form a spherical piece of fly ash if the ash material is liquid for a sufficient period of time. Out-gasing from combustion of the heavier hydro-carbons will provide internal gas pressure to keep the particle spherical until it freezes.

Jan 1, 1978

By Alan J. Michaels

The paper addresses the problem of the high costs of accidents ad how AMAX Inc. - a diversified natural resources company - has managed to control its losses through a tri-thrusted approach of: (1) management commitment, (2) methods of implementation that are tailored to each division or local unit, and (3) a reward system for outstanding performance. Specific attention is focused on the Corporate Loss Prevention Department's "10 Point Program for Loss Prevention Management".

Jan 1, 1981

By J. D. Noll, J. A. Organiscak, A. B. Cecala

Significant strides have been made in optimizing the design of filtration and pressurization systems used on the enclosed cabs of mobile mining equipment to reduce respirable dust and provide the best air quality to the equipment operators. Considering all of the advances made in this area, one aspect that still needed to be evaluated was a comparison of the efficiencies of the different filters used in these systems. As high-efficiency particulate arrestance (HEPA) filters provide the highest filtering efficiency, the general assumption would be that they would also provide the greatest level of protection to workers. Researchers for the U.S. National Institute for Occupational Safety and Health (NIOSH) speculated, based upon a previous laboratory study, that filters with minimum efficiency reporting value, or MERV rating, of 16 may be a more appropriate choice than HEPA filters in most cases for the mining industry. A study was therefore performed comparing HEPA and MERV 16 filters on two kinds of underground limestone mining equipment, a roof bolter and a face drill, to evaluate this theory. Testing showed that, at the 95-percent confidence level, there was no statistical difference between the efficiencies of the two types of filters on the two kinds of mining equipment. As the MERV 16 filters were less restrictive, provided greater airflow and cab pressurization, cost less and required less-frequent replacement than the HEPA filters, the MERV 16 filters were concluded to be the optimal choice for both the roof bolter and the face drill in this comparative analysis case study. Another key finding of this study is the substantial improvement in the effectiveness of filtration and pressurization systems when using a final filter design.

Aug 1, 2016

By Karl R. Zipf

A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine. The gas samples are drawn via vacuum pump to the surface and are typically analyzed for oxygen, methane, carbon dioxide and carbon monoxide. Results of the gas analyses are displayed and recorded for further analysis. Trends in the composition of the mine atmosphere, such as increasing methane or carbon monoxide concentration, can be detected early, permitting rapid intervention that prevents problems, such as a potentially explosive atmosphere behind seals, fie or spontaneous combustion. TBS is a well-developed technology and has been used in coal mines around the world for more than 50 years. most longwall coal mines in australia deploy a TBS, usually with 30 to 40 monitoring points as part of their atmospheric monitoring. The primary uses of a TBS are detecting spontaneous combustion and maintaining sealed areas inert. The TBS might also provide mine atmosphere gas composition data after a catastrophe occurs in an underground mine, if the sampling tubes are not damaged. TBSs are not an alternative to statutory gas and ventilation airflowmonitoring by electronic sensors or people; rather, they are an option to consider in an overall mine atmosphere monitoring strategy. This paper describes the hardware, software and operation of a TBS and presents one example of typical data from a longwall coal mine.

May 1, 2013