Search Documents

By R. V. Ramani

An improved mine environment is the single most critical factor affecting the health and safety of workers engaged in underground coal winning. A very important subclassification of this wide field is mine ventilation, which essentially deals with 'mine atmospheric environmental control.' To ensure proper mine atmospheric environmental control, adequate quantities of air must flow through working sections in the mine. In recent years much attention has been paid to the fan and its prime movers, but the efficient use of the fan output in the workings has not received an equal amount of investigation. In mechanically ventilated mines friction losses in main airways often account for 70 to 90 percent of the total pressure loss sustained in the system. Also the leakage losses are a serious detriment to the efficiency of mine ventilation systems. It is not uncommon to loose 60 to 70 percent of the air between the fan and the last open cross-cuts due to leakage directly into the return Proper assessment of these losses in simulating and projecting complex ventilation systems is vital. Network analysis of ventilation systems is not new. Scott and Hinsly (1951) presented the detailed mathematical framework. Since then work has been done in adopting this technique to analog, and within the past few years, to digital computers. Development of computer programs to solve ventilation network problems has been reported in United Kingdom, Japan, U.S.S.R., South Africa, Germany, and the United States. The purpose of these programs is to serve as an experimental mine wherein analysis of proposed alternatives or ventilation planning can be tested. The great power of the computer as a planning tool lies in the ability to input empirical or Projected data into programs with predicting ability. But, however good a computer program is, unless fairly accurate input information is available accurately assessing the engineering factors of the ventilation system, the output will be suspect. Thus, to simulate and project mine ventilation systems, good estimates of leakage and friction factors are important. Yet, relatively little work has been done in the past three decades to determine these more realistically.

Jan 1, 1973

By Thomas B. Borak, Keith J. Schiager, Janet A. Johnson

OBJECTIVES OF RADIATION MONITORING Monitoring is a tool used in the practice of radiation protection. The primary reasons for monitoring are to reduce radiation exposures to levels that are as low as reasonably achievable and to assure that no individual receives a dose exceeding the maximum individual dose limit. The documentation of radiation doses for legal, medical, or epidemiological reasons is a subordinate function of any monitoring program. The investment in radiation monitoring programs should be guided by four criteria: (1) the detection and avoidance of unnecessary exposures, (2) the magnitude of potential health risks, (3) the determination of combined doses and risks with adequate confidence, and (4) the verification of compliance with established limits. FIRST CRITERION: DOSE REDUCTION - DETECT AND CORRECT UNNECESSARY EXPOSURES The system of dose limitation advocated by the International Commission on Radiological Protection (ICRP, 1977), and subscribed to in a broad sense by various regulatory agencies, is comprised of three essential ingredients: (1) [justification] of any practice that produces radiation doses by some commensurate net benefit, (2) [optimization] of radiation control measures by reducing doses to levels that are as low as reasonably achievable, and (3) [limitation] of individual doses to preclude inequities and [moldistribution] of risks. All too often, only the third criterion - the limitation of individual doses to prescribed regulatory limits - is explicitly addressed in everyday radiation protection programs. The emphasis of most exposure control and monitoring efforts appears to be directed toward limiting and documenting individual doses that might approach the legal limit. The first two criteria, i.e. justification and optimization, should contribute to a rationale for allocating monitoring efforts. When applied to individuals, these criteria mean the detection and elimination of unnecessary exposures. This should be a high priority of any monitoring program. Measurements should be directed toward detecting inoperative or ineffective control measures, whether or not there is a risk of exceeding the individual dose limits. The ICRP recommends a procedure that can be used effectively to reduce unnecessary exposures. A n investigation level should be established at an exposure rate substantially lower than the regulatory limit, e.g. 30% of the limit (ICRP 26, 1977, p.33). Measurements obtained during routine monitoring that exceed the investigation level are evaluated with respect to cause and potential reduction. To be effective, the evaluation results should be formally recorded and conveyed both to management and to the workers involved. Although the investigation level recommended by the ICRP is based on a fixed exposure rate or derived air concentration, an equally effective evaluation program may be based on the investigation of a percentage of all measurements. For example, one might investigate the highest 5% or a random selection of all measurements. In any case, the objective is to detect and correct situations that are producing unnecessary exposures. SECOND CRITERION: MONITOR IN PROPORTION TO THE MAGNITUDE OF RISK The ICRP criteria apply generally to all radiation exposures. However, a second priority for monitoring programs should be established on the basis of the nature of the exposures and the magnitude of the health risks involved. Current practices in radiation protection are based on dose limits to specific organs and assessment of individual exposure pathways, with little consideration of the combined doses from various pathways. Although the intent of the ICRP recommendations was to limit the total dose to each critical organ, combined doses from external and internal sources are rarely determined. The recent recommendations of the ICRP (Publ. 26, 1977) are based on the limitation of total health risk from occupational radiation exposures. Implementation of this concept would necessarily require the measurement, calculation and summation of doses and concomitant risks to all organs of the body from all exposure pathways. The U.S. Environmental Protection Agency has taken the first step toward translating the ICRP recommendations into regulations. The proposed recommendations for Federal Radiation Protection Guidance for Occupational Exposures (USEPA, 1981) include provisions for summing the risk-weighted organ doses to determine compliance with an effective whole-body dose equivalent limit. Whether or not the proposed guidance is modified before final adoption, it seems clear that some version of dose summation and combined risk limitation will be included in future regulations. With this

Jan 1, 1981

By L. J. Buter, D. J. Collins

Introduction FMC's Paradise Peak gold mine was discovered by staff geologists in July 1983. Located south of Gabbs, in western Nevada, the deposit contains about 11 Mt (12 million st) of ore grading at 3.6 g/t (0.105 oz per st) of gold and 129 g/t (3.75 oz per st) silver. It is estimated that the ore contains 34 t (1.1 million oz) of recoverable gold and 933 t (30 million oz) of recoverable silver. The 3.6 kt/d (4000 stpd) mill began operation April 14, 1986, just 18 months after Davy McKee completed a feasibility study and construction, and two-and-a-months ahead of schedule. It also came in about 10% under budget at a cost of about $100 million. Crushing Run-of-mine ore is delivered from the mine in 45-t (50-st) haul trucks to a 272-kt (300,000-st) capacity open air stockpile. Ore is reclaimed using 5 m3 (7 cu yd) front-end loaders that feed a 91-t (100-st) hopper equipped with a 610- x 610-mm (24- x 24-in.) grizzly. A 1.4- x 11-m (54-in. x 35-ft) apron feeder delivers ore from the hopper by way of a vibrating grizzly screen with 127 mm (5 in.) openings to a 1- x 1.3-m (43- x 51-in.) Rexnord jaw crusher. Crushed material is conveyed to a 1.8- x 4-m (6- x 14-ft) Link Belt vibrating screen equipped with a 50-mm (2-in.) manganese grizzly bar deck. Screen oversize is fed to a 1.7/0.6-m (5.5 ft) Rexnord standard cone crusher. Product from this crusher joins the -50 mm (-2 in.) screen undersize and is conveyed to a 136-t (150-st) surge bin. Three hydraulically driven belt feeders deliver ore from the ore bin to three 2 x 6 m (7 x 20 ft) Link Belt single-deck tertiary screens fitted with 6 x 25 mm (0.25 x 1 in.) slotted polyethylene screens. Screen undersize - -6 mm (-0.25 in.) rock - is conveyed to a 3.6-kt (4000-st) ore storage bin. Screen oversize is delivered by way of a conveyor to a 91-t (100-st) surge bin. From this bin, two belt feeders feed ore to two 1.7 m (66 in.) Rexnord Gyradisc crushers, which are in closed circuit with the tertiary screens. Design features include magnetic protection for tramp iron removal and sloping floors and pump sumps for ease of clean up. Dust scrubbers keep the working environment clean and in compliance with state dust emission regulations. Grinding Two 1 x 4.5 m (3.5 x 15 ft) belt feeders deliver ore from the fine ore bin to a conveyor belt that feeds it to the 5 x 7 m (16 x 22 ft) Allis-Chalmers ball mill. The conveyor belt is equipped with a Merrick weightometer. This controls feed rate to the ball mill by speed control on the hydraulic motors driving the feeders. The 2.6 MW (3500 hp) powered mill grinds 3.6 kt/a (4000 stpd) to an average grind of 85% -75 µm (-200 mesh). The mill is in closed circuit with four 660 mm (26 in.) Krebs cyclones. Three of these are normally in operation while one is a standby. Warman pumps feed the cyclones through a cyclone distribution manifold. The cyclone underflow returns to the ball mill, which has a 300% average circulating load. Mill discharge pH is 11, and that is obtained through pebble lime addition to the feed belt. Cyclone overflow is sampled using a Heath & Sherwood two-stage sampler. It then flows to a 27-m-diam (90-ft-diam) Eimco thickener. Thickener overflow is returned to the grinding circuit, while underflow at 50% solids is pumped to the leaching circuit. Grinding-circuit design features include a steeply sloped floor for ease of clean up, an open area over the pumps for maintenance accessibility, and a ball hopper with a self discharge bottom to speed ball addition. Other features include a mill liner handler and an air clutch that connects the mill motor to the mill.

Jan 12, 1986

By R. S. Kinasevich

As part of other work related to the studies of kinetic factors that influence the flotation of specific sulphide minerals, specially designed kinetic flotation experiments at Cominco included work done on -65 + 100 mesh and -100 + 150 mesh, high purity galena. The flotation collector used was sodium isopropyl xanthate containing radioactive sulphur-35. Radiation monitoring of the galena fractions from stage flotation tests indicated that the adsorbed radioactive xanthate was uniformly distributed among the floated fractions and the non-floated, or residual portion of the galena. This anomalous behaviour could not be correlated to changes in Seebeck coefficients, to lattice distortions, or to the nature of the mineral surface as revealed by infrared spectroscopy and by microscopic measurements.

Jan 1, 1970

By Gerald C. Smith

Carlin Gold Mining Company is a wholly owned subsidiary of Newmont Mining Corporation and is located 76 kilometers north west of Elko, Nevada. Multiple bench open pit mining methods are being used to mine 24.5 Mt of ore and waste per year. Mining started in 1964 and up through 1983 Carlin has mined 138 Mt of ore and waste and has milled 13.8 Mt of ore. Selective mining of carbonaceous and oxide ores together with a good grade control program have been key factors in the success of the operation. This paper will present the raining methods and the mining equipment being utilized to make Carlin Gold Mining Company a very profitable operation while mining and milling low-grade gold ore.

Jan 1, 1985

By R. J. Weege

Conventional underground mapping methods and diamond drilling are being applied in a study to determine the nature of the copper ore occurrences near the footwall of the Osceola lava flow top, commonly referred to as the Osceola Amygdaloid. Our work to date suggests that structures formed by relatively impermeable barriers, created by flowage and injection of still-molten lava from the interior of the flow into the solidified, brecciated crust, acted as the ore receptacles. Ascending hydrothermal fluids traveling near the footwall contact were trapped and confined in these barriers which retarded the direct upward movement of the ore fluids and caused deposition of copper. Oreshoots located near the footwall appear to have been formed spatially' independently from the hanging-wall oreshoots by fluids traveling simultaneously, but along different channelways. The barrier concept as advanced by earlier writers to explain the concentration of the ore-bearing, fluids into broad shoots con¬stituting entire ore bodies is found to be equally as applicable for the localization of smaller oreshoots within the Osceola ore body.

Jan 1, 1962

By B. Hester

Many Third World countries of Third World Africa are well-endowed with minerals, especially gold. Political and economic conditions discouraged interest by Western capital for the several decades since colonial rule. Influence from Eastern Block countries has gone and the left wing orientation widely favored by Third World countries has almost disappeared. Under International Monetary Fund influence, these countries now solicit Western finance to expand their industries. Mining is especially encouraged. The paper describes the financing of some recent developments and examines trends and opportunities in some of the more attractive countries.

Jan 1, 1993

By Ray E. Harris

A resource of 134,400,000,000 tons of minable trona and mixed trona and halite underlies an area of about 1,300 square miles vest of Green River, Wyoming (Culbertson, in preparation)(Figure 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6,667,000 short tons (Kostick, 1983), approximately 90 percent of which came from Wyoming trona. This enormous resource occurs in the Wilkins Peak Member of the Creen River Formation (Eocene). The Green River Formation is derived from sediments deposited in a large lake (Lake Gosiute) that occupied the Green River Basin in south-western Wyoming 38-54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition during which time the trona deposits were formed. A total of 42 trona beds are known, of which 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation).

Jan 1, 1984

By W. G. Pariseau

A study of coal pillar strength was done at the Beehive Mine during a three year period, 1974?1977, in a cooperative effort involving the University of Utah, RE/SPEC, Inc., and the American Coal Company (Pariseau et al, 1977). The Beehive Mine is located in the Wasatch Plateau coal field in central Utah near Orangeville, Utah, where mines are developed from outcrops between steep canyon walls with topographic relief of a kilometer or so (3,600 ft). Coal is found in Cretaceous sediments that dip gently to the west. Detailed geology of the Wasatch Plateau is described by Doelling (1972). Mining was done in the Blind Canyon seam. An earlier Deseret Mine worked the Hiawatha seam that is lower in the stratigraphic column by about 36 m (120 ft). Mining progress and ownership changes occurred in time with mine mergers and name changes eventually to the collective Des-Bee-Dove label. At the Beehive Mine, depth varied with topography but was approximately 360 m (1200 ft) on average; seam thickness varied from 1.5 to 6 m (5 to 20 ft) and usually required two passes of the miner. The mine was eventually closed and finally reclaimed in 2003. Semborski and Oakley (2006) present a brief history of the mine and describe the reclamation work in some detail. Figure 1 shows the surface topography in the vicinity of the mine that is in the center of the figure.

Feb 23, 2014

By K. A. Stanley, N. A. Karl, D. R. Wilburn

"This summary of international mineral exploration activities for the year 2014 draws upon information from industry sources, published literature and specialists in the U.S. Geological Survey (USGS) National Minerals Information Center. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analyses of exploration activities performed by the mineral industry.Three types of information are reported and analyzed in this annual review of international exploration: 1) budgetary statistics expressed in U.S. current dollars provided by SNL Metals & Mining (SNL) of Charlottesville, VA; 2) regional and site-specific exploration activities that took place in 2014 as compiled by the USGS and 3) regional events that affected exploration activities including economic, social and political conditions, which were derived from published sources and discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources are used to develop these compilations, statistics may differ depending on the source and type of data that are being reported.The SNL data summarize planned company budgets for worldwide exploration activities in 2014 for 19 nonfuel mineral commodities based on company surveys. Research focused on precious metals (gold, platinum-group metals and silver), base metals (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (iron ore, phosphate and potash), and specialty mineral commodities (diamond, lithium, niobium, rare-earth elements, tantalum and uranium). Information on uranium exploration activities was included for the first time in 2007. Data on lithium, niobium, phosphate, potash, rare-earth elements and tantalum were compiled for the first time in 2010 because of their increased significance. Since 1999, companies with exploration budgets of $100,000 and greater were included in the SNL compilations. SNL budget estimates exclude bauxite, coal and oil and gas. Exploration budget estimates for iron ore have been compiled since 2011 but reported separately. The 2014 SNL company survey is reported by SNL to cover an estimated 95 percent of the world’s nonferrous, nonfuel mineral exploration budgets. The 5 percent that is not covered includes companies that chose not to participate in the SNL survey, private companies that do not publish their budget data, and government-funded exploration activities"

Jan 1, 2014

By J. A. G. Llerena, J. Sattarvand

Tailings dam failures have been occurring in recent years. They are considered more vulnerable than hydraulic dams due to the lack of regulations on specific design criteria, and stability requirements regarding monitoring during the construction and maintenance process. Thus, monitoring the dam is essential to know the dam's existing state and ensure its safety. One of the reasons tailings storage facilities fail is slope instability caused by moisture content. A relationship does exist between moisture content and surface strength, early detection of seepage would help to assess the physical condition of the dam. Moreover, to cover the tailings dam area in an efficient way Unmanned Aerial Vehicles (UAVs) are suitable because of their versatility and high-resolution data acquisition. Mounted with a high-resolution RGB camera, and thermal, or hyperspectral sensors UAVs can acquire good quality images that combined with image analysis and machine learning algorithms yield a good estimate of soil moisture.

Feb 1, 2023

By J. F. T. Agapito

The load carrying capacity of oil shale pillars excavated by conventional blasting, presplit blasting, and mechanical mining is evaluated. The study was based on a comparison of in-situ vertical stresses and fractures obtained from overcoring horizontal holes in the Colony Mine, Piceance Creek Basin, Colorado. Results indicate that conventional blasting causes a zone of damage approximately 3 m (10 ft) thick with low stress distributions. Presplit blasting reduces damage significantly, and increases the load carrying capacity in the 3 m (10 ft) thick zone by 5.93 MPa (860 psi). Mechanical mining causes little or no rock damage, and an increase of 9.83 MPa (1425 psi) in strength in the same 3 m (10 ft) thick zone. An example of pillar design is given showing that the use of presplit blasting and mechanical mining techniques can increase the extraction ratio by at least three and five percent, respectively, as compared to conventional blasting. It is speculated that comparable increases in extraction should also occur due to increases in span dimensions.

Jan 1, 1984

By Yuting Xue, Taghi Sherizadeh, Mark Van Dyke, Dogukan Guner, Khaled Mohamed

The Coal Pillar Rib Rating (CPRR) technique has been developed to assist in rib support design in underground coal mines. One major challenge of the data collection process is the measurement of coal strengths in the field. Schmidt hammer has been verified as a useful tool to determine coal strength. An alternative approach is to obtain the representative strength of coal mass by determining the coal lithotypes in the field based on the coal brightness profile by experienced geologists or mining engineers. In this paper, image processing techniques have been used to quantify the texture of coal images of different lithotypes with the purpose of classifying coal lithotypes. The coal images were collected from the pillar ribs with exposed surfaces in underground coal mines, and the coal lithotypes were identified when taking the images. The method of Gray-Level Co-Occurrence Matrix (GLCM) was used to analyze the textures of coal images of different lithotypes, and the texture parameters, such as contrast, homogeneity, energy, and entropy, were compared. The results show that the images of coal with different lithotypes have different textures, which can be quantified through the image processing. The results from this study demonstrate the potential of classifying coal lithotypes using rib photos and easing the data collection process of CPRR.

Feb 1, 2024

By James M. Barker

The occurrence of borates and zeolites at Mesa del Alamo is well documented by McAnulty and Hoffer (1) and Lefond and Barker (2). Further investigation indicates the presence of priceite and meyerhofferite in addition to the howlite (1) and colemanite (2). Analcime occurs in addition to the clinoptilolite and phillipsite (2). The Mesa del Alamo area is about 200 !a south of Tucson, Arizona, and 13 km southeast of Magdalena, Sonora, Mexico, just south of the unpaved road to Cucurpe (Figure 1). The geology and mineralogy of northcentral Sonora is known only on a regional basis except for small areas mapped in detail during copper exploration. The study area is within the Basin and Range province of North America from which borates and zeolites are now produced in California. The borates and zeolites at Mesa del Alamo occur in geological environments similar to those of the Mojave and Death Valley regions of California (3, 4). Thus, a detailed exploration pro- gram in the Magdalena area could result in the discovery of economic borate and/or zeolite deposits.

Jan 1, 1979

By J. R. Sims

Gold assays from production blastholes in the Mercur Hill Pit were used to delineate known ore zones and to determine how well previous exploration drilling defined these zones. The most important factors causing inadequate ore zone definition were: 1) inappropriate location of drill holes relative to the ore zones, 2) presence of stopes from previous mining, 3) sampling and assaying errors, and 4) smoothing of the ore zone boundaries during ore reserve estimation. Infill drilling strategies were evaluated to determine the efficiency with which a given drill pattern defined the known ore zones. A drilling strategy was developed which improved ore zone delineation when compared to techniques which maintained uniform drill spacing.

Jan 1, 1992

By R. S. Datta

In the article "Concentration of Oil Shale,"(1) Dr. N. Arbiter stated, "One of the major factors in the delayed utilization of oil shale as an energy raw material is the low grade or content of hydrocarbon (kerogen) in oil shale as compared with coal and even more so to the liquid and gaseous fuels. " When the availability of high-grade deposits decreased, mineral industries started adopting prebeneficiation procedures for the low-grade deposits. This practice, which is becoming standard in these other industries, has been largely overlooked by the oil shale industry in its drive to produce oil from oil shale. If a major portion of this mineral matter can be removed, there can be potentially large savings in the capital and operating costs of oil shale retorts. Moreover, the environmental impact, associated with recovering the shale oil, could be reduced considerably. In 1980 Roberts & Schaefer Resource Service (RSRS) completed successfully the first set of demonstration runs with a 20-ton oil shale sample from Cathedral Bluffs (C-b tract), Colorado. This relatively low grade (~12 gpt oil content) oil shale was beneficiated applying the Dutch State Mines Heavy Medium Cyclone process. (2)

Jan 1, 1985

By Dennis P. Bryan

Nevada is especially well endowed with industrial minerals, both in the number of ore deposits and the diversity of commodities. More than 600 significant industrial mineral deposits, containing 22 principal commodities, are present, in the State. The materials produced in Nevada in 1978 had a value of approximately 113 million dollars, and additional processing of some of them (e.g. gypsum into wallboard, limestone and clay into cement) added considerable more value. Table 1 shows the value of Nevada's industrial mineral production in 1978. Nevada currently supplies 85 percent of the country's barite producing 1.6 million tonnes (1.8 million short tons) valued at 30 million dollars in 1978. Nevada is second in diatomite production and contributes one-third of total lithium produced. Other industrial minerals being produced include clays, fluorspar, gypsum, lightweight aggregates, limestone and dolomite, magnesite and brucite, perlite, salt, sand and gravel, and silica. In general, Nevada produces high-value industrial minerals which are not consumed within the State, but rather, are shipped out of State. In contrast, most more populous states produce larger tonnages of lower value industrial minerals which are consumed chiefly within that state.

Jan 1, 1980

By R. Merkl

Since the 1940s, decanter centrifuges have become more important for increasingly complex solid-liquid or solid-liquid-liquid separation processes. Sometimes processed industrial or metalliferous minerals are abrasive or are treated with corrosive chemical agents. Traditional mining applications include the processing of coal, gravel and other products, where low-speed decanters, as well as screen bowl decanters and filters, dominate. These have been increasingly replaced by high-speed decanters during the last decade. Decanter centrifuges also started to play a key role in applications such as drilling muds, processing carbonates and separating SX crud in copper platinum ore concentrations of nickel and gold. Communication between machine producers and mineral processing engineers is vital for the right choice of materials and the design of the right decanter centrifuge for the individual process.

Feb 1, 2012

By Harvey P. Knudsen

This paper describes the results of a comparative study of the geostatistical ore reserve estimation method over three conventional methods; the polygon method, the inverse of the distance squared (IDS) method, and ELIP which is similar to IDS. Each method was evaluated on its ability to accurately predict individual block grades for one bench of the Pima Nine, located near Tucson, Arizona. Results at the Pima Mine indicate that the geostatistical method is no better nor worse in predicting block grades and total tonnage than the ELIP or IDS methods in contrast, the polygon method is clearly inferior. All of the methods would have given better results if geology had been included in the block model. At already producing mines ELlP or IDS may be good choices since they involve substantially less cost in computer time. For prospective or new properties, the geostatistical model is more attractive, due to its ability to construct confidence limits on the estimates.

Jan 1, 1976

By Thomas E. Ban

D-LM at Mobile The qualified success of iron ore pelletizing processes has influenced considerations for production of highly beneficiated fur¬nace charges. Such beneficiation would necessarily involve some forms of chemical and perhaps thermal conversion for production of prereduced pellets, preheated pellets, precalcined pellets, and perhaps pellets which contain all of the above features as preheated, prereduced, precalcined products. This type of furnace burden will be adapted within a new ironmaking process to be activated commer¬cially during the latter part of 196$ in Mobile, Alabama. This process will integrate a new pelletizing system with an electric smelting furnace and the pellets will be comprised of a composite charge blended from metallurgical proportions of iron ore, coal, and limestone. The plant as designed and constructed by McDowell¬-Wellman Engineering Company will feature the D-LM process and will be owned by McWane Cast Iron Pipe Company. It is significant to

Jan 1, 1968