Search Documents

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL STATEMENT The primary objectives of any field data gath¬ering effort should be to (1) identify and gather the data necessary for the project and (2) obtain the data in a state-of-the-art manner. All too often the initial field data are collected both areally and tem¬porally in an illogical manner without the guidance of a conceptual model of the ground water flow systems involved or even a review of existing geo¬logic literature on the area of interest. The initial data collected frequently are of limited value while necessary basic reconnaissance information is miss¬ing. Initial field data should be collected with the intent of developing a hydrologic overview of the potential mine site and surrounding area. Ob¬viously, one of the initial objectives is to define the area requiring a hydrologic investigation. The data requirements should be identified by the time frame in which collection should be made and by the corresponding increase in sophistication of the data requirements with development and operation of the mine. The data requirements are summarized in Table 1. INITIAL LEVEL SITE INVESTIGATION Area Determination The initial task of any hydrogeologic investi¬gation is to determine the boundaries of the area requiring study. Obviously, the site of the proposed mine is included in the study area. The areal extent beyond the site may be determined from an eval¬uation of existing geologic and topographic maps. Those formations that overlie the ore body, the formations containing the ore body, and the formation(s) that lies immediately beneath the ore body are of direct concern for proper site recon¬naissance. Additional formations below the ore body may require study depending upon their thick¬ness, hydraulic conductivity, and degree of inter¬connection with the mine workings. This initial viewpoint identifies hydrostratigraphic units based strictly on geologic concepts such as mineralogy and structure. Formation outcrops, synclines, an¬ticlines, faults, and fracture and joint patterns are used to delineate the area of the site reconnaissance. The simplistic hydrogeologic environment (il¬lustrated in Fig. 3, chapter 2) requires that field data be collected via test wells and/or geophysical techniques. This approach is necessitated by the lack of surface features such as formation outcrops, streams, and springs. Fig. 5 (chapter 2) illustrates a slightly more complex hydrogeologic regime. The potential mine sites at locations A, B, C, D, and E each intercept a different ground water flow sys¬tem or combination of flow systems. Therefore, each mine location requires that a different area and size of area be investigated. A more complex geologic setting as illustrated in Figs. 6 and 7 (chapter 2) may be approached differently. The area included for the site recon¬naissance should encompass sufficient surrounding area to include the outcrops of those formations suspected of being influenced by the future mine. Even adjacent areas not suspected of being influ¬enced may be investigated if the formations of in¬terest crop out in those areas. Such an extension of the area of investigation would provide a greater regional understanding of the hydrogeologic properties of the formations (hydrostratigraphic units) of interest. Geologic Investigation The initial step before conducting the site re¬connaissance is to review all existing literature on the geology of the area. Existing information should be augmented with new exploration data on the dip, strike, thickness, and lateral extent of the for¬mations in the area. Exploration hole logs should be reviewed for indications of lost circulation, rub¬ble zones, and water producing zones. Existing aer¬ial photos such as those available from the US Department of the Interior, EROS Data Center,

Jan 1, 1986

By W. Kemp Wait

Electronic ore sorting is a coarse particle beneliciating process which performs a function which in the past was primarily achieved through the use of hand picking belts. Photometric ore sorting is capable of separating waste from mineral bearing rock having a distinct difference in surface light reflectance levels. This type of ore sorter can be applied to gold and silver ores which are contained in quartz veining. Photometric ore sorting has been used at gold mines in South Africa as well as the Black Pinc silver mine in Montana. A new ore sorter has recently been developed with precious metal ores in mind. This ore sorter is capable of sorting ores on both photometric and conductivity sensing parameters. The first production machine has been installed at a gold mine near Beardmore, Ontario and currently is being used to process low grade waste dumps.

Jan 1, 1998

By J. D. Miller

Certain bituminous coals of recent geological age are known to contain a significant quantity of natural (fossil or subfossil) resin. Such resinous coals are found in the western U.S., particularly the Wasatch Plateau coal field in Utah. Some of the seams in this field contain approximately 5% resin which has been recovered by gravity and/or flotation processes since 1929. Resin concentrates thus produced are of low quality and are usually refined by solvent extraction and precipitation. The purified resins are of commercial importance, being used in the adhesive, varnish, enamel and ink industries, etc: Recently, an improved flotation technique has been developed which involves ozone conditioning to selectively float resin from such coals. In this flotation process, a concentrate product which contains 95% resin at a recovery of 80% can be obtained in a single stage from coal containing approximately 10% resin, whereas conventional flotation at a similar level of recovery produces a concentrate having a resin content of 30-40%. Economic analysis shows that the ozone flotation process has good potential for use by industry.

Jan 1, 1988

By Dwane K. Johnson

INTRODUCTION The small mining company faces the dilemma of how to finance the development of its properties because it doesn't have the financial resources to pay for the development costs from its own funds and doesn't have the financial strength which will enable it to borrow the money needed for development. However, with a little imagination and the right set of circumstances, a financing can be arranged for the small mining company. This paper is an attempt to describe the fundamental steps on how such financing can be obtained --in other words--what is required to provide ad- equate capital at a low cost for developing and bringing a mining property into production. Innovative financing follows from this. The basic keys for building and maintaining a successful mining company are "the four M's": Management, Market, Mine, and Money. The writer believes their order of importance is as presented and each is a building block required in order to obtain the type of financing that best suits the borrower and lender. MANAGEMENT Management must be experienced, highly organized, realistic, able to take advantage of opportunities and fulfill promises. Mine financing requires a variety of skills and concentration on the part of management. Management should have a thorough understanding derived from experience in geology, construction, mining and metallurgy and environment, marketing, and financial matters. Management must realistically visualize what will be produced at what cost and truly evaluate the risks associated so the proper security can be correctly designed. Since risk cannot be eliminated, the objective of management is to identify the risk which will be present in a given venture and assess the level of that risk which will be acceptable to the firm. Generally the risk which is present is subject to little or no modification. After management identifies and measures the acceptable risk the firm will proceed in a way that it will be least exposed. Management must determine its long-term objectives and strategies within the context of a constantly changing world. This question must be addressed before examining the sorts of risk which affect the development and operation of a specific property. The compilation and interpretation of "hard data" by competent people is good to a point but the experience and instinct of seasoned individuals are the important factors in management choosing a long-term direction for the corporation. The attitude towards risk greatly affects the goals of the corporation. Major risks in a mining project can be placed in four categories: 1. Market - Price, demand, substitution. 2. Costs - Capital, operating, financial. 3. Regulation. 4. Taxation. The feasibility study for a project is the fundamental tool used in the management of risk. Management should employ an experienced team with an established and well-understood set of ground rules for the preparation and assembly of a feasibility study. The necessary degree of realism is built into all levels of the study and if the project is technically feasible, the company's hurdle rate is then used to discount the base-case project cash flow in order to determine its financial viability. Understanding the geological significance of the mineral deposit is critical. There should be strong interplay among the pure regional geologist, the detailed mine geologist, the mining engineer, and the metallurgical engineer. The collaboration among these different disciplines will yield a feasibility study that is more reliable. The essence of this work must be appreciated and understood by the executives planning the financing. It is vital that they thoroughly understand the risks and make the proper risk assessments to cope with our rapidly changing market environment. Projecting future revenue values is paramount and is subject to much estimation. One way to mitigate fluctuations and the risk of falling prices is by selling production for future delivery. MARKET Since mining is a worldwide industry it is mandatory that bankers be aware of what is occurring in the marketplace, both foreign and domestic. The marketing of the production is a very important facet when considering financing for the small

Jan 1, 1987

Introduction The US mineral industry in 1983 participated in the recovery from the recent recession. Compared with 1982, the value of raw nonfuel mineral output rose 8% to $21.2 billion. The $218 billion worth of goods processed from this crude mineral output represented a 9% increase over 1982. Even in real terms, these figures reflect growth. Demand for nonfuel mineral materials, of course, depends on the overall state of the economy, which steadily improved each quarter in 1983. Of particular importance to the mineral industry were surges in key mineral-consuming sectors such as construction and automobile manufacturing. New housing starts rose one-third, to 1.7 million units, while automakers turned out about 35% more cars (6.8 million) and 25% more trucks (2.4 million) than in 1982. These are significant increases, even considering recent trends toward smaller, lighter vehicles, and multiple-unit housing. A comeback for the mineral industry, however, is bound to proceed unevenly, particularly at the beginning. Traditionally, the industry lags behind the rest of the economy during a recovery, and some mineral products respond to overall economic improvement more quickly than others. This pattern has been repeated many times and the industry is used to it. Mineral executives know it is best to be patient and cautious during the first stages of an economic upturn. Many experts say that it may take extraordinary toughness, patience, and caution this time around. Steel Improves Raw steel production - a major indicator of both material use and mineral production - rose 14% to 77 Mt (85 million st), stimulating a 7% rise in domestic iron ore production to 39 Mt (38 million It). Still, the iron ore industry operated at less than half capacity, with most major mines remaining closed for part of the year. Iron ore imports dropped 24% to 10 Mt (11 million st), so demand was partly met by withdrawals from stocks. Despite the increase in steel production for 1983, output remained far below levels of just a few years ago. For example, 1983 production was still 29% less than in 1981. Raw steelmaking capacity actually declined about 10% during the year to 122 Mt (135 million st). The industry continued to cite steel imports, especially those from developing nations, as a major cause of domestic capacity loss. As long as steel production remains weak, steelmaking metals suffer. Domestic producers of bulk ferroalloys of chromium, manganese, and silicon operated at about one-third capacity in 1983, with six of the 19 companies involved being closed all year. The US mined no manganese or chromium, and very little nickel, although the country's only nickel mine did resume production in November. Molybdenum production, at 13.6 t (15 st), was only about one-third as much as in 1982. The major molybdenum mines, Climax and Henderson in Colorado, remained closed all year. To meet demand, molybdenum stocks were halved to 19 t (21 st). Mine shipments of tungsten, another mineral tied to steel production, dropped 30% to 1.1 kt (1,200 st) of contained metal. One of the most positive responses to the general economic recovery came from the aluminum smelting industry. By the end of the year, it was operating at about 79% capacity, compared to 59% in January. Nevertheless, the 3.3 Mt (3.64 million st) of primary aluminum produced represented only a slight increase over 1982. Total bauxite imports were about 27% below 1982 levels. Production of magnesium metal rose 11% to 100 kt (110,000 st). But titanium was more typical of other

Jan 5, 1984

By Cong Shi, Cuiping Li, Enji Sun

"Tailings dam is a subsidiary facility of mining production. In order to decrease tailings dam accidents caused by the failure of flood drainage system, this paper proposed a framework of potential failure detection system of tailings dam flood drainage facility based on three dimensional panorama technology. A collection device of three dimensional panorama is designed to capture the onsite images of flood drainage system of tailings dam. The spatial information of flood drainage facility of tailings dam is recovered through projecting the image information to spherical surface by using three dimensional panorama technology. Two dimensional images are transformed into three dimensional images in three stages of panorama images process, which are pretreatment, registration and splicing. Combined with the framework of HTML5, panorama images are embedded into webpage. These web pages have the functions of user interface that the images could be displayed, moved and zoomed. With the function of interaction with panoramic display, 3D panorama scenes can be changed and scaled. Browsing the webpage is helpful to find potential risks such as possible holes, fractures and leakages of flood drainage system of tailings dam. The realization of this system can detect the potential safety risks of flood drainage system of tailings dam. The application of this system would improve the safety and provide the ability of accident pre-warning. It is useful to maintain the healthy and sustainable operation of tailings dam.Introduction It is reported by Xie et al (2009) that tailings dam are necessary facilities for mine production and places which constructed by damming troughs or encirclement used to store tailings that eliminated after ore selection in Metal and non-metallic mines. It is reported by Mei (2012) that tailings dam is a dangerous source of high-energy man-made debris flow, the collapse of the tailings dam takes devastating damage, which seriously threatens the safety of life and property of the enterprises and the downstream residents. It is reported by Dong (2011) that the collapse of the tailings dam causes secondary disasters such as environmental pollution at the same time. It’s a serious impact on regional economic development and social stability. The phenomenon of collapse of destruction is general excessively of tailings dams in China. It is reported by Zhang et al (2011) that most of these phenomena are caused by flood over the top of dams. The main reason is the lack of capacity or the failure of the drainage system. There are also accidents caused by the failure of drainage system in foreign countries in recent years. For example, November 5th 2015, the tailing dams collapsed because of the insufficient drainage capacity of the Germano mining area in Germano Mariana area in central Minas Gerais state in Brazil. After a small post-earthquake, the liquefied tailings fill sand submerge downstream cities and towns. It finally destroyed 158 houses, killed at least 17 people, polluted 663km river and destroyed 15 square kilometres of land along the river. It is reported by Rico et al (2008) that it’s necessary to continuous monitor and control the tailings drainage system in order to reduce the occurrence of tailings accidents and guarantee the sustainable production of the mine. The traditional artificial detection methods of flood drainage system of tailings dam exist many problems such as heavy workload, low efficiency, and susceptible to meteorological conditions. And it is reported by Luo (2013) that the tailings dam wastewater is corrosive which result a certain disease in flood discharge facilities such as tailings drainage culvert, etc. In order to realize the effective monitoring, management and maintenance of flood drainage system of tailings dam, advanced technologies need to be used to acquire the information of collection and management of flood drainage facilities of tailings dam."

Jan 1, 2017

By K. A. Eriksson

Over 25 years ago, SKEGA pioneered the use of rubber linings in grinding mills and rubber is today widely accepted and almost standard material chosen for Regrind -and Secondary Mills. There are, however, only a few Primary Mills in operation with "solid" rubber linings because available materials and designs are often not cost efficient in comparison with steel alloys on a cost per ton basis and/or downtime for liner replacement would be too high.

Jan 1, 1988

L.R. Bower In regard to the paper by J.B. Gwiazda, it makes a highly technical approach to show that the µ factor used by designers of lemniscate-guided roof supports has never really been confirmed as a maximum and assumes that convergence is vertical. Also, the paper does not appear to take into account deflection of structures, which occurs when the lemniscate and base members are fully loaded to their maximum stress level, nor the front to back line of the support in relation to differential roof to floor movements caused by strata movements under pressure. It is not unusual for differential movements to be slightly diagonal to the line of the support, particularly in faulted areas and on gradient faces. The paper also does not take into account consolidation of fines immediately above and below the support. Generally speaking, any differential movement is from face to waste and under these conditions the µ of 0.3, which appears to be an international standard, has worked in practice. However, if the face end of the support is lower than the waste end, then the µ of 0.3 can be considerably increased, giving rise to the damage mentioned in the paper. The ideal design should aim for a slightly forward bias in the lemniscate guide so that the last increment of setting is toward the face, tending to close any fissures that may have developed during the support advance cycle. The support should also be fitted with positive set valves to ensure that a high setting load density is attained to minimize bed separation. As far as powered supports are concerned, convergence is irresistible and all powered supports converge at their rated yield load. A similar principle can be applied to the differential roof to floor movements to drastically reduce the very high forces that would otherwise be applied to the lemniscate structures and pins and that, in turn, are transferred to the base arrangement and floor loading. Any differential movements are usually catered for by the 0.3 µ factor or deflection of structures in the lemniscate guide arrangement and consolidation of the floor. The floor loading, due to differential movement, is in addition to the support convergence load and requires additional bearing area to avoid possible floor penetration. Some seven years ago, Fletcher Sutcliffe Wild Ltd. (FSW) introduced a lemniscate-guided shield support where the lemniscate linkage is connected to the roof bar through two horizontally converging rams to allow differential movement to take place above a given rated figure. This is a known force and can be guarded against, whereas with rigid connections the forces, as yet, are unconfirmed. By careful design, a horizontal force in excess of 6 MN (60 tons) opposes differential movements for a total ram loading of only 2.5 MN (25 tons), or 1.25 MN (12% tons) each. This principle can considerably reduce the length and weight of the support in comparison with a rigid pin-type structure ; also, the yield load rating can be increased without affecting the lemniscate forces. The graph shows the tensile and compressive forces in a lemniscate linkage of a support with and without hydrostore. These forces react into both the roof beam and base members and, as can be seen from the support height to linkage load graph, a considerable reduction in these reactions is gained by the use of the FSW patented hydrostore system. Floor loading is considerably reduced under maximum µ conditions, and by allowing the roof bar to move with the strata, some degree of improvement to strata control is achieved in line with the assumptions in the paper. In practice, these movements have only been in the region of a few millimeters, which, in turn, reflects on the improvements to strata control by the addition of positive set valves. Supports to this design of both 450- and 280-t (496-and 309-st) rating have been successfully used in the United Kingdom for several years, negotiating many faulted areas without one single reported need for repair or maintenance. This includes supports left unattended during the year-long strike, proving the reliability of the system.

Jan 8, 1986

By John G. Myers, William A. Vogely, Harold J. Barnett

INTRODUCTION, CONCEPTS, AND MEASUREMENT Introduction Periods in the history of man, from his earliest appearance to the present, are often characterized by the principal materials used. In nearly all cases, the material or fuel is of mineral origin-stone, copper, bronze, iron, coal, and so forth-indicating the principal ingredient of the tools or source of power of the period. Each of these periods represented great improvement over the preceding one in terms of human well-being, as measured by population growth and other indicators (Cipolla, 1978). A major reason for the improvements in production and well-being was the nature of the material or fuel, each successively superior to the preceding, which made it possible to produce more food, fuel, shelter, and clothing with a given amount of labor. If we accept this well-documented description of economic progress as accurate, we may then turn to the consideration of two related questions concerning this development. The first, easily answered,-is why man spent long periods of time (millenia, in many cases) making tools from inferior materials, such as copper, instead of passing directly to superior materials, such as iron and steel. The second, closely related question, concerns the relation between the rate of economic growth and the quantity of mineral reserves available at any time. For the first question, the answer is that the technology required to discover, extract, and process each successive material had to be discovered and developed before the material could be used. Once the technology was available, the new material could be and was exploited widely, raising productivity-output per unit of labor- and consequent consumption per person. This familiar idea underlies a fundamental principle of the economics of resources, namely, at any time, available resources depend upon available technology. No mineral or other raw material is a resource unless the technology has been developed to utilize it. But once the technology is at hand, the new resources associated with it provide the means for economic growth and rising levels of living. This principle is subject to certain conditions. For example, governments or other institutions may prevent a mineral from being used, even though the technology is available. And, if a mineral is located in a remote place, transportation charges may make it uneconomic to exploit. Such minor qualifications do not, however, change the thrust of the argument that technology is the overriding determinant. With respect to the second question, it might seem apparent that the greater the quantity of reserves available, up to some point, the more economic growth will be facilitated. This line of reasoning leads to the conclusion that as re- serves are consumed the quantity available will be reduced and economic growth will eventually be restrained. Reasoning of this sort underlies much popular (and scholarly) thought, in which depletion of mineral and other resources is assumed to lead to constraints on economic growth, through higher materials costs and absolute limitations on materials use. Two important qualifications must be made to this explanation, however, which together

Jan 1, 1985

By S. G. Axen

Design of wells for in-situ leaching is based on individual mining operation and ore deposit requirements. Major design considerations are well flowrate, depth, fluid composition, expected well life, mine operating plan and cost. A large variety of downhole equipment, materials of construction, contract services and methods of well completion and stimulation are available. A generalized design procedure which allows the engineer to optimize well design for a particular ISL application is described.

Jan 1, 1988

By V. P. Petrov, V. S. Znamensky

There are a great number of asbestos deposits in the USSR, and some are quite large. The main deposits of chrysotile asbestos are shown in Fig. 1. The Bazhenovo deposit, which is located in the Sverdlovsk region, is the largest and has been mined since 1889. Systematic studies of asbestos deposits were begun from the very be- ginning of Soviet government and are most often connected with the names K.E. Tarasov, P.M. Tatarinov, B.J. Merenkov, N.D. Sobolev, F.V. Syromjatnikov, V.N. Lodochnikov, V.P. Petrov, V.P. Eremeev, L.A. Sokolova, V.R. Artemov, and V.F. Dybkov. Investigations by these people and others helped the USSR be one of the most important producers of asbestos in the world. In this chapter, the main asbestos deposits of the USSR are explained in a general outline from the point of view of their genesis, common features, and differences that must be taken into account for forecasting, exploration, and the mining of asbestos. All chrysotile asbestos deposits of the USSR were formed from magnesium rock as a result of comparatively low grade temperature, hydrothermal alteration, and free crystallization of fibrous chrysotile in open cavities that served as catalysts. Chrysotile, a widely distributed rock-forming mineral, is not in general an important mineral for industry as it is a long fibrous and main vein variety. However, it must serve for geologists as an important prospecting criteria. And, the geologist should search for the mineral not only in places of possible chrysotile generation, but in places where asbestos may be crystallized in its long fibers. The Soviet geologists distinguish chrysotile asbestos deposits in two groups: (1) ultrabasic rocks and (2) sedimentary dolomite terranes, taking into account how the maternal rock was affected by hydrothermal solutions. The largest deposits are related to ultrabasite. In dolomite, the largest deposits are small and their asbestos contains almost no iron, which makes it a better filler for insulating plastics. There are a few types of asbestos deposits within the limits of the ultrabasic group, the largest being a Bazhenovo type to which the deposits of the Urals are attributed. This Bazhenovo asbestos is characterized by the most complete zonality of disposition for various kinds of asbestization. These types of deposits are, for the most part, the only ones presently working in the USSR. The Bazhenovo deposit is connected to the gabbro-peridotite intrusive belt that is about 180 km long and is broken into a number of fault blocks as shown in Fig. 2. Granitoid veins of intruded rocks are found along the deepest faults, and were sources of hydrothermal solutions that affected the maternal rock. The nearest granitoid vein, ultrabasite, is substituted by listwanite that consists of quartz, talc, carbonate, and some other essentially talcous rock. The next zone of hydrothermal alteration is composed of serpentine. The boundry between serpentinite and unaltered ultrabasite is as irregular, diffuse, and rough as the boundaries between all other zones. Nearer the vein of granitic rock, ultrabasite is entirely serpentinized into massif serpentinization that penetrates through cracks and fissures. There is an unaltered ultrabasite space between fissures, and the biggest block is preserved unaltered in the central part of the massif. The Soviet geologists call this ultrabasic sopka. Preservation of the unchanged blocks is of great importance for deposit formation as volume changes are impossible during the process of asbestization and serpentinization. It may be confidently said that asbestization in Bazhenovo type deposits is possible only when alteration of ultrabasite has not completely occurred. Under conditions of massif volume, a very big mass of substance must be carried out of the ultrabasite for the progressive stage of serpentinization. However, in the regressive stage,

Jan 1, 1986

By Basil S. Fee

INTRODUCTION Probably the most important family of chemicals used in mineral processing today is a category of basic commodity chemicals loosely denoted as pH regulators. Typical chemicals which are referred to as pH regulators include lime, magnesium hydroxide, soda ash, caustic soda, ammonia, sulfuric acid, and hydrochloric acid. These chemicals are often used in very significant amounts in almost all of the major mineral processing operations such as flotation, hydrometallurgy, etc. (in dosages up to ten pounds per ton of feed ore treated). While cheaper in cost per unit weight of chemical than more specific chemicals such as collectors, frothers, extractents, etc., the overall cost to the mill operator is generally higher with pH regulators per ton of ore processed than with any other given processing chemical. For example, a rough rule of thumb in sulfide mineral flotation is that the cost of lime is double that of the collector(s) used. The symbol pH is used to designate hydrogen ion concentration. When acids, salts, and bases are dissolved in water, individual molecules are dissociated into their constituent radicals or ions. The strength of an acid or a base increases with the extent of such dissociation or ionization. An alkaline solution is one in which the number of Qydroxyl ions (OH ) exceeds the hydrogen ions (H ). In an acid solution, the hydrogen ions predominate. In either case, both ions are always present as water itself ionizes to a limited extent, that is: [ ] The pH scale is logarithmic and the pH value is the negative of the logarithm (base 10) of the molar concentration of hydrogen ions per liter of solution. For example, a pH of 5 means that the molar concentration of hydrogen ions per liter is 0.00001 (1 x 10-5). Likewise, a pH of 9 means that the molar concentration of hydrogen ions per liter is 1 x 10-9. Normally, the relationship between hydrogen ion and hydroxyl ion concentration is based on the relationship: Concentration of H ion x concentration of OH- ion = constant. Eq. (1) In dilute and/or moderately concentrated solutions that are normally used in mineral procygsing processes, the constant at 25°C is 10-14. On the pH scale, the value of pH equal to 7 represents the hydrogen ion concentration of a neutral solution. pH values lower than pH 7 indicate increasing acidity and higher values than 7 indicate alkalinity. Table 1 shows the nature of the pH scale at 25°C. Temperature affects the extent of ionization of dissolved acids, salts, bases, and water so that the hydrogen ion concentration (hence pH) of a solution is also affected by temperature. As a means of demonstrating this dependency, Table 2 shows the change of the exponent of the constant (base 10) in Eq. 1 and the pH value corresponding to neutrality as a function of temperature. It is also important, for example, that alkalinity or acidity expressed by pH not be confused with total alkalinity or total acidity. For example, total alkalinity is commonly determined by titration with a standard acid solution (usually HC1). pH is a measure of the hydroxyl ion concentration of an alkaline solution, whereas titration is a measure of an alkaline solution's acid neutralizing capacity. Thus, if one takes a series of various alkaline solutions prepared using different chemicals but all of exactly the same pH (and temperature) and then subsequently carries out a titration on each solution with a standard acid, it would be observed that the various alkaline solutions would neutralize entirely different amounts of acid. As an example, 0.08 grams of caustic (NaOH) , 6.32 grams of soda ash (Na2CO3), and 8.17 grams of ammonium hydroxide (NH4OH) all have a pH of 11.3 at 25°C. One liter of each of the above solutions neutralizes 0.073, 4.348 and 8.496 grams of HC1, respectively. Therefore, depending on the specific use of any given pH regulator, special tests need to be run by the mill operator to determine factors such as: the specific technical goals to be accomplished by

Jan 1, 1986

By George H. K. Schenck

INTRODUCTION Boom-type miners mechanize the cutting and loading of a solid face of rock having a compressive strength as high as 124 MPa (18,000 psi). These machines differ from continuous miners in that they can cut much harder rock for any given cutter-motor power. In addi¬tion, a boom miner is more flexible, selectively cutting any cross-sectional configuration from circular to square arched faces, 1.57-rad (90°) turns, and mixed faces. The basic operational concept of these machines, utilizing a rotary cutterhead mounted on a slewing boom, gained importance in Europe during the 1960s, where, due to their specialized use in roadway development in coal mines, they were called roadheaders. Along with continuous miners, boom miners share the ability to fully mechanize the cutting and loading of rock, while eliminating the need for explosives and the shattering and overbreaking of roof and rib rock that is normal with conventional mining methods. The machines are crawler-mounted and most have a gathering-arm load¬ing system that, moves the cut rock onto an internal chain conveyor, subsequently discharging the rock into a transport device such as a shuttle car or a bridge conveyor. Light- to medium-weight boom miners are cutting softer rocks and minerals successfully, including coal, shale, rock salt, potash, phosphate, weak sandstones (e.g., those associated with uranium ore), and other softer ores such as iron. Heavy third-generation ma¬chines have extended rock cutting to much harder ores such as borate, oil shale, and almost all rock associated with coal seams, except for the harder sandstones and limestones. The mention herein of specific manufacturers, brand names, or models is made by way of example only and does not constitute endorsement by the author or The Pennsylvania State University. All costs cited herein are in 1977 US dollars. TYPES OF BOOM MINERS All boom miners utilize drag bits fixed on a rotary cutterhead that is powered by an electric motor mounted in the slewing and elevating cutter boom. The cutter¬head is either a ripping or a milling type, and the machines have evolved through three generations (Boldt, 1977). As shown in Fig. 1, only one boom miner cur¬rently produced can use both ripping and milling cutter¬heads on one machine. Table 1 lists boom-miner models built in large num¬bers and/or successfully used or marketed in North America. Table I excludes machines of which only a few have been produced and none sold in North America, such as those manufactured by Demag, Eick¬hoff, Paurat, and Thyssen-Rheinstahl. The only Ameri¬can boom miners are the F-16 and Super ROC¬MINER"', manufactured by AEC, Inc., State College, PA. Machine Generations Three generations of boom miners can be distin¬guished according to their times of introduction, their rock-cutting abilities, and their weight classifications. Fig. 2 illustrates typical best-practice production rates possible from boom miners for selected cutter-motor power sizes (other power figures can be interpolated). Productivity is related directly to the energy applied to the cutterhead and indirectly to machine weight; higher

Jan 1, 1982

By Erling Stranden, Leiv Berteig

INTRODUCTION The measurement of the total activity of radon daughters in the air of mines has become a routine procedure in order to control the radiation exposure in miners due to the inhalation of these radionuclides. Normally the measured concentration is given in terms of total potential L-energy of the short lived radon daughters. The unit most frequently used is 1 WL (working level), which is defined as the potential a-energy of 1.3.105 MeV per 1 of air. The a-dose to the respiratory tract is, however, not proportional to the inhaled potential a-energy. In addition, the degree of equilibrium between the daughter products in air and the fraction of daughter products not attached to aerosol particles (the unattached fraction) must be known. Theoretical calculations of the equilibrium between daughters and the unattached fraction have been presented by different authors (Jacobi, 1972; Porstendörfer et al, 1978). Such calculations must take into account the plateout of daughters on surfaces, the attachment of daughters to aerosols and removal of daughters by the ventilation. The situation in mines will however be very complex and no single model will cover all situations. In most cases the radon and radon daughter concentrations will be described by a combination of different models. Domanski (1979) used the experimental results of Breslin et al. (1969) from uranium mines to relate the equilibrium between the individual daughters to the equilibrium factor, F. Once the equilibrium factor is known, this seems to be a useful approach to assess the individual daughter concentrations. The concentrations of radon and daughter products may vary considerably during the day. Seasonal variations are also frequently found. It is therefore important to have knowledge of the magnitude of these variations and of the factors having the strongest influence upon the concentrations. The unattached fraction of radon daughters in uranium mines was investigated by George and Hinchliffe (1972) and Raghavayya and Jones (1974). Mercer (1975) later modified the results of Raghavayya and Jones. Both these investigations indicated that the aerosol particle concentrations was the main influencing factor upon the unattached fraction. In this paper we will summarize the main results of a study on the radiological characterics of nonuranium mines. We will also discuss the correlations between the unattached fraction of the potential a-energy and the unattached fraction of the individual daughters, and between the equilibrium factor F, and the individual daughter ratios. More detailed discussions of this study will be published elsewhere (Stranden and Berteig, 1981 and Stranden and Berteig 1981 a). MATERIAL AND METHODS During 4 two-weeks periods corresponding to the seasons in the Norwegian mine where the highest radon daughter concentrations occure, the parameters listed in table 1 were studied. TABLE 1 Parameters measured during the study [Parameter Methods Radon Scintillation flask/Continuous ionization chamber Radon daughters Tsivoglou(1953)/Kusnetz(1956) Respirable dust Cyclone Unattached fraction Wire screen (Stranden and Berteig 1981) Atmospheric pressure Continuous baragraph Temperature and Continuous thermohygrograph humidity] At a fixed location, the radon concentration was measured continuously by a ionization chamber (Stranden, 1981), during these two-weeks periods in order to study short-time and seasonal variations. RESULTS Correlation between equilibrium factor and individual daughter ratios. The mean value of the equilibrium factor in all Norwegian mines measured during the last ten years was 0.46 with a minimum of 0.08 and maximum of 0.93 (Stranden and Berteig, 1981). The correlations between the equilibrium factor F, and the individual radon daughter/radon ratios were studied and the results indicated high correlations. In table 2, these correlation formulae are listed together with the correlation coefficients. TABLE 2 Correlation between the equilibrium factor, F, and individual radon daughter ratios [Formula Correlation coefficient RaA/Rn = 1.14 F 0.551 0.76 RaB/Rn = 1.00 F 0.940 0.99 RaC/Rn = 0.77 F 1.120 0.92]

Jan 1, 1981

By R. Edward Williams

The Spa1lation Process Because of the low thermal conductivity of many hard rocks, rapid heating of these rocks produces a thin surface layer in which the temperatures attain high values. Thermal expansion of this surface layer is constrained by the reminder of the still cool rock, and when stresses within the surface rock become high enough, the surface rock breaks away from the cooler rock behind it and flies or falls off as a thin flake called a spall. Then the next, newly exposed surface is heated, and the process continues. This process is the basis of spallation drilling. The hot gases from a jet burner provide the heat for spallation to occur, and their high velocity provides a scouring action that transfers heat to the rock and removes the spalls as rapidly as they form. Spallation is a process which works in very hard rock. It is dependent upon the thermal expansion coefficient and the thermal diffusivity of the rock but is also affected by any discontinuities in the rock. To date the efforts which have been made to evaluate the various rock according to their spallability has been minimal. As the success of this process is dependent upon the characteristics of rock it is expected that the study of rock mechanics will prove to be of greater value to this program than to the other mechanism for drilling and excavating rock. Commercial Uses of SPALLATION In the 19408s, the Linde Air Products Division of Union Carbide (UC 1 began developing spallation for use in mining taconite ore, which is presently the chief source of iron in the United States. In this work UC developed a jet-piercing tool that burned fuel oil with oxygen to produce spallation and contained mechanical cutters to remove rock that was not amenable to spallation. The UC jet-piercing machines have since produced about 40 million feet of shallow blast holes used for emplacing explosives in the taconite mines. During this work it was found that hole diameters could be increased by merely reducing the advance rate of the burners and that existing holes could be enlarged by making another pass through the hole with the same burner. The Browning Engineering Go. of Hanover, N.H., has developed a hand-held spallation burner to cut slots in granite. It has been used for a quarter of a century and is now standard equipment for quarrying granite throughout the world. This burner, which resembles a small jet engine oriented with its exhaust pointed downward, is the forerunner of a flame jet burner used to spall experimental holes in granite at maximum rates in excess of 100 ft/hr when operating in hard, competent granite. It uses No. 2 fuel oil, which is burned with compressed air. The system uses water to cool the burner and the exhaust gases. These gases, along with the steam produced from the cooling water, blow the spalls from the hole. Experimental Work Theoretical and experimental work has been accomplished by the Massachusetts Institute of Technology and the Los Alamos National Laboratory. This work is reported in Refs. (3) and (4). To verify the experimental results of this work laboratory scaled down field tests were conducted using two we1 1 characterized granites from quarries in Barre, VT and Westerby, RI, under defined heating conditions. In the laboratory tests a propane - oxygen heating torch was used to direct a flame at the granite surface and the spal 1 ing process was examined at various heating rates with a high-speed video taping system operated at 200 frame per second. This produced a time-lapse sequence where the onset of the spallation process was easily distinguished. Also the heat flux from the torch to a flat surface at various stand off distances and flows was measured. A similar set of tests was conducted using the more easily quantified and uniform heat source of a 1.5 kw GO2 laser. This allowed accurate

Jan 1, 1986

By James M. Williams, Michael E. Zellars, Arthur J. Roth

INTRODUCTION Our present estimates of world P205 consumption for all uses show an average annual growth rate of approximately 1.9% per year. The estimated 1985 consumption of 41.5 million tonnes of P205 is predicted to increase to 57.1 million tonnes of P205 by the year 2005, which represents a growth from 157.7 million tonnes in 1985 to 217 million tonnes of phosphate rock in 2005. The present situation of oversupply and extremely weak phosphate product prices is, however, expected to continue in the short term and a normal supply/demand balance may not be achieved until after 1990. The growth in P205 demand, in conjunction with the higher cost of replacing low cost mines as they are depleted, will place economic pressure on world farm economies through the increased cost of phosphate fertilizers. The availability of rock supply is not the challenge; rather, it is the economics of new rock supply. This economic challenge of providing new rock supply is by no means limited to the United States. Even in centrally controlled economies, the cost of rock from domestic mines of marginal quality and economic viability, coupled with burdensome infra¬structure requirements, may result in tonnage additions at very high cost. Although government subsidies to offset higher production cost is a factor in some countries, world production in the next 20 years will be directed, if not governed, by economic factors. Established infrastructure, good quality reserves, and existing operations will provide a competitive advantage for new prod¬uction. It is our opinion that the current world supply structure will remain relatively stable through 2005, in that most of the traditional suppliers will retain supply roles. U.S. rock production, although it is not expected to grow beyond the present level, will still be a major contributor to world supply. Although dramatic changes within mining, fertilizer production and farm economics may appear disruptive, the current supply scenario will, in general, continue with the major issue being production economics. WORLD DEMAND Demand for P205 by region in the world has been estimated using projections of population, crops and yield, arable land, economic and other data as a basis for future demand projec¬tions by Blue-Johnson and Associates, our col¬laborators on a recent multi-client study. Non-fertilizer P205 demands were estimated in the same general manner. These estimates of future demand are based on an assumption of reasonable world political and economic stabil¬ity, debt repayment requirements maintained at workable levels, and resolution of problems in the agricultural economy to a point where normal supply/demand forces can interact freely to provide a basis for continued P205 supply. The results of these studies indicated an average growth rate of 1.9% per year through the year 2005. This growth could be as low as 1.5% per year, or as high as 2.5% per year. It is our opinion that the estimated rate of 1.9% per year is most probable. This moderate growth rate considers both the major economic constraints facing the world agricultural industry today and the general problem of affordability of fertilizers and other crop inputs. WORLD SUPPLY There are adequately defined world reserves of phosphate rock today to provide supply well into the future, even at much higher levels of demand than presently projected. Using the U.S. Bureau of Mines estimates, which are based on stringent criteria for definition of reserves, the present world reserves base is approximately 35 billion tonnes. Identified resources raise the potential for production by orders of magnitude. Potential resources based on geological trends, and including offshore deposits, would again result in orders of magnitude increases in rock resources. Morocco leads the world in reserves base with approxi¬mately 21 billion tonnes. The U.S. is second, followed by the Republic of South Africa and Russia. These four countries control about 87%

Jan 1, 1986

By B. A. Hancock

It is not at all surprising that causticized potato and potato derived amylopectin starch solutions performed much better than their parent starches. Some preparation is required to rupture the starch granules to effect the polymeric adsorption and interparticle bridging necessary for selective flocculation. In laboratory work comparing the deslime performance of causticized and autoclave cooked laboratory corn starch solution preparations, it was found that higher deslime weight rejections, with attendant proportionally greater iron unit losses, occurred with the causticized starch. These results may be specific to the ore involved but they do suggest that cooking and causticizing cause different starch granule rup- ture and/or starch breakdown, which have an effect on desliming response. I calculated from the data in the article that the slimes product grades were high - 24.3% and 20.3% Fe when 53.7% and 54.5% Fe concentrate products were obtained, respectively, in Table 4, and 21% Fe with a 62.6% Fe concentrate in Table 5 - using the natural tailings sample, which had a head of 34.3% Fe. It may be advisable for the authors to consider different starch preparations in future investigations. The combination of upgrading and selectivity results presented in Table 4 are not as good as the authors suggest. The authors' claim that a system has been developed to produce saleable concentrates from the Kudremukh tailings is quite disconcerting. There are many hurdles yet to be crossed before commercial application of selective flocculation becomes possible because differ- ences between the very small-scale laboratory tests conducted and commercial application are rather large. Among the many differences are varying circuit feed grades that will occur from use of tailings, the apparent face that much lower tailings grades will be encountered in practice (it is much easier to achieve a high concentrate grade with reasonable recoveries using 34.3% Fe tailings as in the study rather than 25.3% Fe tailings grades that the plant apparently averages), the hydraulic nature of the thickeners used in operations compared to the static system used in laboratory tests, the different size distributions that will be obtained from a plant closed grinding- classification circuit, and differences in water used in a plant operation and the laboratory. The authors wrote that it was necessary to overgrind to be sure that the coarse gangue would not settle with the iron oxide floccules. This situation is likely to be exaggerated in commercial operations where it is assumed cyclones would be used for classification. Because cyclone classification is greatly influenced by particle densities, there will probably be an even greater difference in size between the iron and gangue particles in the plant, which would make the gangue slightly coarser still in relation to the iron. This would make the selective flocculation-desliming separations using the procedure employed by the authors even more difficult and, using the dispersant system the authors employed, greater overgrinding would be required. To grind finer to minimize the coarse gangue in the flocculated iron oxides is quite inefficient and appears not to broach the problem. The actual problem appears to be insufficient dispersion of the ground pulp. In this situation, addition of a dispersant would likely be required to attain a sufficiently high pulp dispersion level to efficiently effect a selective flocculation-desliming separation. Although the very coarse particles would still have a tendency to settle with the floccules, it probably would be found unnecessary to overgrind as much as indicated. Use of an optimum combination of dispersant and pH modifying reagents may also significantly improve the selectivity of desliming. Additionally, although it is possible that sufficient dispersion may be obtained by pH control alone in some situations, it is quite probable that added dispersity was obtained in the reported work from using distilled water. It is research experience that distilled water enhances dispersion. In commercial operations it may not be expected that sufficient dispersion will be obtained by pH control alone, unless the water used in the process is by nature quite dispersive. Overall, a change in the Kudremukh tailings dispersant scheme appears necessary where a dispersant is used in conjunction with a pH modifying reagent. With this change, different dispersion-flocculation responses will result that would have to be further evaluated. Therefore, it is still an open question whether an efficient and effective selective floccula- tion separation using Kudremukh tailings may be obtained that will produce saleable concentrates.

Jan 1, 1987

By Andrew N. Peterson

US mine operators frequently fail to investigate more cost effective and productive bulk material handling systems because surface mines seem to lend themselves to truck ore haulage. In this country, as a result, use of conveyors to move heavy loads from mine to process facilities has been minimized, if not actually neglected. In contrast, there are more than 50 conveyorized surface mines in successful operation around the world. These mine operators have learned that properly applied conveyorized systems can offer major savings in capital and operating costs, which contribute to improved profits when combined with other proven mining technologies. Growing acceptance and application of conveyorized bulk material handling in surface mines also points up how unique each mine is and how careful planning contributes to maximum mine effectiveness. Because of these differences, mining executives and technical and operating staffs need to develop an understanding of three factors in applying conveyorized bulk material handling in surface mines: • Why each mine will benefit from the type of automation permitted by conveyorized operation, •What kind of equipment is available, and • What applications most effectively demonstrate the first two factors in action - hauling either ore or waste. The conveyorized systems considered in this presentation have production rates from 0.5-2.7 kt/h (500-3,000 stph). Worldwide, these systems have been operating since the early 1960s. Advantages of Conveyors Why do you want conveyorized bulk material handling? First, it almost always provides lower operating and maintenance costs. Second, it frequently requires lower initial capital costs and almost always requires lower capital costs over the life of the surface mine. Third, it provides comparable operating availability, and finally, it frequently gives comparable operating flexibility - depending on the mine plan. Cost avoidance can be accomplished with modern production methods. These, in turn, permit increased productivity and reduced operating costs such as those for energy, maintenance, and manpower. It has been demonstrated in European surface mines and elsewhere, that conveyor systems frequently require lower initial costs than does truck haulage. Almost always such operations require lower capital costs over the mine life. Those costs include the continual addition of haulage trucks to both accommodate the increasingly difficult haulage routes and fulfill replacement requirements when trucks wear out. Conveyor systems handling ore in numerous large crushing and port facilities, which have operated since the early 1950s, have clearly demonstrated a useful conveyor life of more than 25 years. In contrast, off-highway trucks have life spans of six to eight years. The following examples illustrate comparative capital costs to purchase conveyor systems and comparable truck haulage units. Example 1 The ore haulage route from point A to point B is level and 610m (2,000 ft) long. The material weighs 1.8 t/m3 (110 lbs per cu ft) and must be transported at a rate of 1.8 kt/h (2,000 stph). The installed capital costs to provide a properly designed conveyor that will transport the described material from point A to B is about $450,000. The capital cost to purchase three 77-t (85-st) off-highway trucks and one spare truck - which would provide equivalent capacity - would be about $1.2 million. The truck cost estimate is based on a 6 min. or 771 kt/h (850 stph) truck cycle time. Truck efficiency is estimated at 0.8. Each 77-t (85-st) truck would have an actual haulage rate of 617 kt/h (680 stph). Therefore, three trucks would be necessary to transport the designated tonnage of 1.8 kt/h (2,000 stph). A movable crushing plant would be located at point A for the conveyors and a permanent crushing plant at point B for the truck haulage system. Capital costs for these primary crushing plants were not included in the calculations for either system because the capital costs are frequently comparable. Example 2 The transport route from point A to point B is 610 m (2,000 ft) horizontally and 122 m (400 ft) vertically - on a 20% grade (Fig. 1). The material weighs 1.8 t/m3 (110 lbs per cu ft) and must be moved at a rate of 1.8 kt/h (2,000 stph).

Jan 6, 1983

By D. A. Norrgran, J. A. Marin

Introduction The recent development of rare earth permanent magnets has revolutionized the field of magnetic separation. The advent of rare earth permanent magnets in the 1980s provided a magnetic product that was an order of magnitude stronger than that conventional ferrite magnets. This allowed for the design of high-intensity magnetic circuits that operated energy free and that surpassed electromagnets in the strength and effectiveness. New applications and design concepts that focused on the mineral and metal processing industries have evolved. This technology led to the development of various magnetic separators specifically designed for mineral processing applications. Applications that were not previously considered are now being used in primary mineral upgrading, recycling and secondary recovery. Historical perspective Lodestone was the first naturally occurring permanent magnetic material known. Lodstone was most likely used to upgrade iron ore by early civilizations. By the 1600s, the early magnet technology had advanced to quench-hardened iron-carbon alloys. The practical significance of magnetic separation was formally recognized in 1792 when an English patent was issued for separating iron ore by magnetic attraction. By today's standards, carbon steel is a very poor magnet material. It is easily demagnetized and has a very low energy product of much less than I MGOe (Million-Gauss-Oerstads). This was state-of-the-art technology for almost 300 years until chromium was added to magnet feedstock, which resulted in a three-fold increase in the energy product. The well documented addition of cobalt to permanent magnets in 1917 initiated the 30-year era of "Alnico" magnets that at the time provided a superior magnetic energy product. Since then, the science of magnetism has advanced rapidly and is now considered a highly developed branch of physics and material science. Permanent magnets have had an extremely long history. Figure 1 presents a chronology of permanent magnets that illustrates the increase in energy product. Amazing developments in material science have taken place in the last two decades. The gradual advancement of permanent magnet technology was shattered in 1967 with the initial development of samarium-cobalt (rare earth) magnets. Since that time, the advent of neodymium-boron-iron magnets provided such an increase in energy product that new design concepts were considered. New avenues of study were introduced by the complexities in the material science and physics involved in describing these new permanent magnets. Furthermore, applications for permanent magnets that were previously not considered were now viable. Rare earth elements Rare earth elements have claimed the attention of scientists for the past century. These elements were originally termed "rare" because they were thought to be quite scarce. Since then, however, geological studies have shown them to be relatively abundant. The discovery and identification of rare earth elements is complicated by the inherent difficulties in separating them from each other. The rare earth elements comprise the fifteen transition elements of Group IIIB, Period 6, of the periodic table. These elements extend from lanthanum to lutetium and are commonly called the lanthanide series. Samarium and neodymium are the two most common elements used in the commercial manufacture of rare earth permanent magnets. Commercial grade rare earth magnets There are only a few common types of rare earth magnets that are considered in the circuit design for magnetic separators. Early rare earth magnets of commercial significance (introduced in 1970) consisted of the first generation of sintered SmCo5. The energy product of these magnets ranged up to 23 MGOe, which provided the initial impetus to the field of high-energy permanent magnets. Although these magnets did not produce the extremely high magnetic field strengths of current rare earth magnets, they were relatively temperature stable. Containing 66% Co, they are the most expensive of the basic commercial rare earth permanent magnets. Their use is limited today because they are being replaced by second and third generation rare earth permanent magnets.

Jan 1, 1995

By LeEtta M. Shaffner, John R. Marks

INTRODUCTION In the last twelve years, underground stoping methods at the Homestake Gold Mine have evolved from open cut-and-fill with jacklegs, cribbed raises and electric slushers to ramp-based mechanized cut-and-fill (MCF) and vertical crater retreat (VCR) with dieselpowered loaders, trucks and drill jumbos. The evolution was swift. Unfortunately, ventilation practices have had trouble keeping pace. Stope ventilation is still too dependent on auxiliary fans and coolers. A single large MCF stope might contain up to eight headings, each of which requires significant ventilation resources when a diesel loader is present. Air is shortcircuited all too frequently through mined-out VCR panels. These factors and the recent rapid decent of the center of mining prompted a study to improve ventilation practices and to more accurately project future requirements. BACKGROUND In 1992, the underground portion of the Homestake Gold Mine produced 8336 kg of gold from 1407 ktons of ore (268,000 oz from 1,551,000 st). The ore is hosted in low to medium grade meta-sediments. Stoping took place from 420 to 2347 m below the surface (1400 to 7700-ft levels). The weighted center of mining was 1662 m deep (5450-ft level) in 1990 and is projected to be 1890 m (6200-ft) in 1993. The deepest level is 2440 m (8000-ft) where the virgin rock temperature (VRT) is 56.1°C (133F). The mine is ventilated by 504 m3/s (1,069,000 cfm) measured at mid-exhaust-circuit density. The air-conditioning system includes an 8.1 MWR (2300 ton) controlled recirculation plant, a 2.0 MWR (580 ton) chilled water plant, a 1.0 MWR (290 ton) exploration drift refrigeration plant, 28 spot-coolers totaling 3.4 MWR (960 tons) and 35 spray coolers totaling 1.5 MWR (420 tons). The mine employs 117 diesel units with a total nameplate rating of 7961 kW (10,672 hp). These units include twenty-four 1.5m3 (2-yd) loaders, twenty-six 2.7m3 (3.5-yd) loaders, fourteen 3.8m3 (5-yd) and two 7.6m3 (10-yd) trucks, and assorted utility vehicles and drill jumbos. THE STUDY In April 1991, the University of Nevada-Reno (Mackay School of Mines) and the South Dakota School of Mines and Technology cooperated with Homestake on an MCF study. Mackay instrumented a stope with thermocouples, air velocity meters and hygrometers (Duckworth, 1992). South Dakota Tech conducted a finite-elements computer analysis of a back-filled MCF stope with/without light-weight shotcrete insulation on the sidewalls and back (Chellam, 1992). Homestake conducted an empirical analysis of deep-level MCF stoping. This paper describes the Homestake study. Twenty-three of the forty MCF stopes deeper than 1800 m were surveyed at least once during the last quarter of 1992. The stopes not included were being cable-bolted or back-filled. Figure 1 shows the complexity of one of the ramp-based stoping areas included in the survey. This particular stope has six separate production headings. A baseline wallrock heat load was derived for each stope or heading from psychrometric calculations. Broken ore, waste rock fill and fissure water were noted when present and the effects included in the baseline heat load. Other heat sources often mentioned in the literature such as metabolic heat from workers, heat from explosives and small electric loads were neglected. Fan heat was considered part of the ramp & crosscut heat load and thus not included in the study. Diesel heat was addressed separately. RESULTS Survey results, plotted as the heat flux against VRT, are shown in Figure 2. The equation for the regression line is: W/m2 = 2.1236*VRT - 75.405 The 0.31 correlation coefficient is poor which implies that the results should be used cautiously. Previous experience strongly suggests that differences in productivity are most likely responsible for the scatter in data points. A rapidly advancing stope will have a

Jan 1, 1993