Search Documents

By R. H. Grau

This Bureau of Mines report describes methane liberation trends from all U.S. coal mines liberating over 100 Mcfd (100,000 cfd) (2.8 Mm3/d). Detailed are results from the latest Bureau survey performed in 1985 and shown are mine and company name, location, coalbed and methane liberation quantity. The report shows that in 1985, there were 180 mines producing more than 100 Mcfd (2.8 Mm3/d) and the total quantity of methane liberated by these mines was 303,900 Mcfd (8,605 Mm3/d). This data is compared with previous studies performed in 1971 , 1973, 1975, and 1980. From 1971 to 1985, there was a 10% decrease in the number of mines liberating at least 100 Mcfd (2.8 Mm3/d) but there was a dramatic 34% increase of liberations from these mines. The increase seems to be caused by new mines being developed in deeper, gassier coalbeds, particularly in Alabama. Likewise, in comparing the ten highest liberating mines in 1975, 1980, and 1985, an increase in methane liberations each year was experienced. The report classifies mines by three levels of liberations: greater than 100 Mcfd but less than 500 Mcfd (2.8 to 14 Mm3/d); 500 Mcfd to 1 ,000 Mcfd (1 4 to 28 Mm3/d); and greater than 1,000 Mcfd (>28 Mm3/d). It was found that 87% of liberations were from mines producing over 1,000 Mcfd but these accounted for only 38% of all the mines in the study.

Jan 1, 1987

By Nick Barton, Harald Hansteen

The deformations resulting from excavation of very large openings are compared using two-dimensional F.E. continuum analyses and discontinuous physical models (20,000 discrete blocks). Both the joint orientations and the model horizontal stress levels were varied. Some models were dynamically loaded to simulate earthquakes (0.2-0.7 g). Model deformations were recorded using photogrammetry. The changes in deformation when increasing the simulated spans from 20 m to 50 m were of particular interest. High horizontal stress caused surface heave when joint orientations were favourable for arch stability. Joint orientations also determined whether the pillars between parallel openings were in a state of compression or tension. INTRODUCTION The engineering performance of large rock caverns has traditionally been learned from mining and hydro power projects, where the depth below surface is often many times greater than the span of the openings. Deformations measured in the walls and roofs of hydro power caverns generally range from about 5-50 mm, though there is a documented case where a wall moved in 126 mm (1), and another where the arch moved down 147 mm (2). The chief objectives of the present studies of large near-surface openings were threefold: (i) to provide deformation data to compare with monitored data from planned engineering projects involving large span near-surface excavations, e.g. underground sports complexes, civil defense shelters, nuclear power stations,

Jan 1, 1979

By D. U. Deere, T. R. Harrell

Factors such as rock cover, rock type and rock quality can exert a dominate influence on the behavior of a concrete tunnel lining. This paper will present and discuss the investigation, evaluation and use of such factors at the Rocky Mountain Pumped Storage Project in the design of the 10.67m (35 foot) diameter concrete tunnel lining. A plane strain, finite element analysis was performed on the concrete/rock system. The finite element model consisted of a concrete lining zone and three (3) rock zones; a highly destressed rock zone, a transitional rock zone and an intact rock zone. Zones were differentiated from one another by varying the modulus for each zone. Results of this study yielded a concrete lining strain from radial expansion which was used in the crack control calculations for the concrete tunnel lining. After the tunnel excavation was performed, plate jacking tests and additional seismic surveys were run on the tunnel walls. This testing served to confirm the rock modulus values used in the preliminary analysis. However, results were observed which indicated that a two zone rock model would more accurately represent in-situ rock conditions than the three-zone rock model used in the preliminary analysis. This revision to the concrete/rock model was made and a final concrete tunnel lining analysis was performed.

Jan 1, 1986

By John L. Habberstad, Robert R. Thompson, George B. Wallace, Robert C. Bates

INTRODUCTION Rock bolts are one of the most common mine support systems in use today with approximately 90 to 95 million used annually in the nation's coal, metal and non-metal mines. By far the largest majority of these are steel bolts with mechanical expansion shell anchors. Many theories have been advanced to explain the ground control achieved through the use of rock bolts. Most of the theories are applicable to a specific set of circumstances, geology, geometry, rock properties and in-situ stresses. Examples are those which relate the beam building or strata-hanging theories of ground support used in the rectangular openings of a coal mine(l). In tunneling and most metal mining, either circular or horseshoe shaped openings are normally used. Here, bolts may be used to develop a radial stress around the opening, which adds stability to that opening, or merely pin blocks of rock back into more stable ground so that they cannot slip. In most cases, the bolts are torqued to a specified value to seat the anchor and to achieve the pre-load or tension that is desired. To be effective, however, this tension cannot be lost through bolt slippage or creep frequently caused by blasting, moisture attack or raveling of the rock surrounding the drill hole, etc. Furthermore, in soft rock or in oversized holes, sufficient anchorage cannot be achieved with the mechanical anchor, and in very brittle rock the concentration of forces produced by the expanding anchor might cause a crack to propagate from one drill hole to the next. Mechanically anchored bolts are also short lived in mines or tunnels having a corrosive seepage. The steel in these installations can fail

Jan 1, 1974

By A. Fiszer

One of the major problems with deep Polish hard coal mines are deformations of close-to-wall galleries since they are necessary and must he kept open for emergency situations and are largely responsible for work disturbances. In order to ensure safe and effective working operations, it is necessary to often rebuild galleries which, apart from the inevitable stoppage of operations, is greatly disadvantageous for the operation of a mine. The largest problems with maintaining the galleries open occur in Lower Silesian Coal Field mines where sometimes it is necessary to reconstruct the galleries several times [(Fig. 1)]. In light of what has been said above, the aim of this article is to present the reader with methods and ways of determining deformations occurring in close-to-wall galleries. Squeezing or convergence of headings is only a portion of the entire process of ground movement caused by ground disturbance due to workings. The term "squeezing of headings" is to be understood as a shortening of the distance between a point set on the roof of a heading and the corresponding one on the floor. It is very important to know the rules governing the process of squeezing in a particular mining system since it affords possibilities to define changes of the process and its parameters at any moment for a given system. This is of utmost importance because convergence of a heading is one of the most significant manifestations of ground pressure which has already been proved by studies performed by Everling (1). On the basis of those studies it has been observed that there exists an almost linear relation between the rate of convergence and loading [(Fig. 2)]. This, in turn, means that the deformations of the already exploited portion of heading are proportional to the pressure changes.

Jan 1, 1982

By Nestor M. Fillip

INTRODUCTION The Advisory Conference on Tunneling held in Washington, D.C. in 1970 under the auspices of the organization for Economic Cooperation and Development (OECD) forecast that $54 billion would be expended by member countries on underground construction in the 1970s. Construction activity since the Conference indicates the forecast may have been conservative. Statistics in the report indicated a vast increase in tunneling projects for mass transit, hydro-electric development, railroad tunnels, sewer and sewage retention reservoirs and water tunnels. Development of equipment is required to meet the demands for high speed excavation and provide tunnel driving systems with maximum efficiency and capability to sustain high speed advance rates. BORING MACHINE CAPABILITY During the last decade, use of Tunnel Boring Machines (TBMs) has increased. Where ground conditions and limits of machine design criteria permit, circular tunnel sections are either the only section , or an alternate sections specified in the documents: a TBM is either required or is an acceptable alternate means of tunneling. The evolution and acceptance of the TBM has had an impact on the construction and to a lesser degree on the mining industry. The traditional drill-blast-muck or "hand" mine

Jan 1, 1974

By J. C. Watts

Ball mill grinding circuit control has received increasing emphasis in the past few years due to such factors as declining ore grades, increasing production costs, and advances in analytical devices and minicomputer technology. Since ball mill circuits have been a traditional bottleneck in mineral processing plant throughput, control systems often improve through- put without requiring additional processing equipment. In addition, much of the variability of the grinding product size and consistency is often removed, allowing better process operation downstream. Among the problems which arise in designing and implementing a process control strategy for ball mill circuits are circuit constraints imposed by processing equipment and local management, proper instrument selection, installation and maintenance, and use of calculated or inferred variables for process measurements. This paper discusses these problems and attempts to identify valid approaches to their solution.

Jan 1, 1979

By Alan J. Reed

The Afton copper-gold mine is located in the southern interior of British Columbia, 16 km (10 miles) west of Kamloops and 257 km (160 miles) northeast of Vancouver. 'An aerial view of the property in 1976 is shown in Fig. 1. The Afton copper-gold ore body [27 Mt (30 million tons)] of open pit ore with a grade of 1.0% copper, 0.46 g/t (0.01 6 oz per ton) gold, and 4.1 g/t (0.12 oz per ton) silver, occurs within the Triassic Iron Mask pluton adjacent to its faulted contact with Tertiary rocks. The geological setting of the Afton ore body is described by Carr and Reed (1976). Rocks of the Paleozoic, Mesozoic, and Cenozoic eras outcrop in the vicinity of Kamloops, but the unit with the greatest economic significance is the Upper Triassic Nicola volcanic group and its subvolcanic dioritic intrusion, the Iron Mask pluton. The Afton ore body occurs at the northwesternextremity of the Iron Mask pluton immediately south of a deep graben structure that developed in post-Triassic time (Coast Mountains orogeny) and which was the focus of vigorous sedimentation and volcansim in Tertiary times. The Iron Mask pluton is a lenticular composite intrusion approximately 14.5 km (9 miles) in length in a northwesterly direction. The petrography of the Iron Mask pluton ranges from picrite and serpentinite to latite porphyry. Outcrops of individual petrographic units are generally elongate in a northwesterly direction parallel to the axis of the pluton. The Iron Mask pluton represents the moderately slowly cooled core of an oceanic fissure volcano which built up an island flanked by shallow-water sediments including reef knolls and which, during its later stages, intruded its own volcanic pile.

Jan 1, 1991

By Kenneth J. Reid

The application of computers for control purposes in hydrometallurgical processes is not as well-established as in mineral processing plants. This is not only due to the comparatively new development of large-scale application of hydrometallurgy and the relatively small number of operating plants, but also due to some of the basic dynamic characteristics of hydro- metallurgical processes., Basically there is little difference in the development and application of digital control techniques in hydrometallurgical plants from those techniques widely in use throughout the chemical process industry and in nonslurry applications; particularly for those cases involving liquid streams only, the primary sensing elements are essentially the same. On-stream X-ray fluorescence analysis is a well-established method for determination of metal content in the process streams, and standard equipment is used for the measurement and control of pH, flow, density, temperature, pressure, and other variables. Nevertheless, the high proportion of corrosive slurry streams at elevated temperature and pressure poses a challenge to the instrument engineer concerned with developing long-life, reliable instrumentation. One major difference and potential problem area in developing control systems for hydro- metallurgical processes is related to the very long time constants which are common in the larger plant. In these circumstances, it is important to define the overall control objectives very carefully and be prepared to allow for considerable drift in intermediate variables. In larger projects with many control loops the general advantage of lower costs compared to conventional analog instrumentation can be confidently expected. Also in most cases, the process analysis necessary to design and specify a comprehensive computer control system and the increased operator involvement in implementing digital control systems yield additional benefits due to the increased understanding of the dynamic characteristics of the process.

Jan 1, 1979

By P. Piga, O. Sammarco

There is a markedly increasing tendency to design deeper and deeper mines, to use larger amounts of explosive per round, to increase the advance rate of the excavations and so the natural ventilation tends to be more intense in the new mines. For this reason, the mines that make use of powerful mechanical ventilation should also take into account such factors as natural ventilation pressures, especially in the case of mines excavated in high-temperature rocks for which natural ventilation is particularly intense. The results of the studies reported here refer to a very hot mine excavated in an area with a high geothermal flow (the Boccheggiano - Campiano mine, southern Tuscany). At various external temperatures, experimental measurements and analyses have been made of the trend of the thermodynamic characteristics of the ventilation air and of the trends of the air/rock heat exchange along the downcast shaft and along the upcast shaft. These data were then used to work out approximate values of the corresponding natural ventilation pressures. After having identified the most conspicuous variations of the thermodynamic parameters of the ventilation air and the factors causing them, an assessment was made of the repercussions they have on the air flow rates and, above all, on the climatic conditions of the underground excavation sites. The natural ventilation pressures were found not to be constant in time; indeed they change continously and it is difficult to predict the changes. Moreover, it was found that their influence on the ventilation of a section of the mine network is greater if the effect of mechanical ventilation on that section is weaker. In the mine section where the measurements were carried out, some portions were found where the ventilation could become insufficient as a result of the effects of natural ventilation pressures. Finally, some guidelines to be followed in designing hot mines have been put forward which ensure efficient ventilation throughout the network at times with the aid of the natural ventilation pressures, which in certain circumstances may reach very high values in mines of this type.

Jan 1, 1987

By R. V. Ramani, S. Tan

In this paper, several commonly used computer truck-dispatching criteria are evaluated. A computer-oriented truck-dispatching and production simulator was developed to provide data for comprehensive cross comparison among the dispatching criteria. The definitions, primary considerations, characteristics and performances of these dispatching criteria were investigated. From the simulation results, it was concluded that, in general, no one criterion can dominate all others. However, several dispatching criteria that have good potential to increase performance can be identified. All basic dispatching criteria, including minimizing truck waiting time, waiting shovel with minimum waiting time, minimizing truck saturation, maximizing truck momentary productivity or optimization of truck routes, provide local optimal solutions. To obtain a direct global optimization solution for this complex stochastic process does not appear to be likely Therefore, the search for an optimal dispatching criterion that will fit all conditions may not be realistic. It may be necessary to search for a hybrid combination of the several truck dispatching criteria that have good potential for a given situation. An approach to selecting such a hybrid dispatching criterion is presented.

Jan 1, 1993

By Carol A. Hill

Native sulfur occurs with barite, celestite, and bioepigenetic calcite in the Culberson, Pokorny , and Leonard Minerals deposits, Delaware basin. The sulfur in these deposits, in "castile" masses, and in deposits of the Fort S tockton district have 6 34s values between +9 and -15. Native sulfur in the caves of the Guadalupe Mountains is somewhat lighter [(634s = -15 to -25)]. Barite in the Culberson, Leonard Minerals, and Comanche Creek sulfur deposits have 63% values of +35 to +73; celestite in the Culberson and Leonard Minerals occurrences have values of +38 and +36, respectively, and 87Sr/86Sr values of 0.707808 and 0.708138, respectively. Barite associated with sulfide, deposits, Guadalupe Mountains, have [634s] values of +41 to +62. Barite at Seven aeart Gap, Apache Mountains, is somewhat less enriched in heavy sulfur [(634s = +14 to +37)].

Jan 1, 1992

By Stephen J. Reynolds

Arizona's geologic history is complex, resulting in a diversity of rock types and earth materials, including those of commercial interest. Regional variations in geologic history gave rise to three geologic provinces and an inequitable distribution of both metallic and nonmetallic mineral wealth. The Colorado Plateau is largely composed of flat-lying Paleozoic and Mesozoic sedimentary rocks and late Cenozoic volcanic fields and sedimentary deposits. Associated resources include gypsum, halite, sylvite, clays, specialty sand, flagstone, volcanic products, and aggregate. The adjacent Transition Zone features a large expanse of Proterozoic rocks, economically important Devonian and Mississippian carbonate rocks, and Tertiary volcanic and sedimentary materials. Nonmetallic resources in this province include facing and dimension stone, aggregate, decomposed granite, chrysotile asbestos, gypsum, clay, barite, fluorspar, zeolites, and limestone used for lime, cement, and railroad ballast. The Basin and Range Province has the most complex geologic history and, therefore, the most diverse assemblage of industrial mineral occurrences. These include halite, gypsum, clay, aggregate, decomposed granite, diatomite, zeolites, perlite, pumice, kyanite, limestone, marble, stone, and others. In addition, young stream deposits yield vast quantities of sand and gravel, Arizona's most economically important nonmetallic mineral commodity.

Jan 1, 1987

By Richard Switalski, Thomas Scotese, James Morrison, Randall Essex

OVERVIEW Like many older metropolitan areas across the U.S., the Greater Cleveland area is served by a combination of separate sanitary sewers and combined sanitary-stormwater sewers. In 1966, a Master Plan was implemented by the Northeast Ohio Regional Sewer District (District) to minimize pollutant overflows into adjoining Lake Erie and its tributary rivers and streams, that would occur during wet weather events. One component of the Master Plan was to reduce the load on combined sewers by constructing new conveyances to intercept separate sanitary flows and convey them to upgraded regional waste water treatment plants for priority treatment. As part of a 15-year program to construct 74 km (46 miles) of new interceptors, the West Leg Interceptor (WLI) Project intercepts flows from four decommissioned waste water treatment plants (WWTPs), and conveys those flows to the new Southwest Interceptor (SWI), which conveys the flows to the Southerly Treatment Plant, a tertiary level treatment facility. The WLI Project was built in sections to permit decommissioning of the WWTPs as each segment of the interceptor system was completed and put into service. Flows from the first of the four WWTPs was converted to the WLI in November, 1992; the final connection was achieved in July 1994. The WLI comprises 9.1 km (5.7 miles) of 21 to 29 m (70 to 95 ft) deep mainline interceptor tunnel, four vortex drop structures, approximately 2 km (1.3 miles) of shallow tunneled connector sewer to the mainline, approximately 2.9 km (1.8 miles) of open cut connector sewers, five construction work shafts (not including one work shaft constructed under SWI Contract 6 at the north end of the WLI), and 15 access shafts.

Jan 1, 1995

By R. Latifovic

Assessment of the possible impact of existing and future mining projects located in remote areas may be difficult and costly. This may have an adverse effect on the process of issuing mine permits and development of new mines. A remote sensing based land cover change assessment methodology presented in this paper is a promising avenue to render this process more meaningful, precise and affordable. It has been applied to a case study of the Oil Sands Mining Development in the north-east of the Canadian province of Alberta. Recently, the Athabasca Oil Sands Region (AOSR) is a place of unprecedented growth of open-pit mining operations. This study was focused on the primary impact onto the landscape and vegetation resulting from exploration and, mining development. This impact was assessed using an information extraction method applied to two LANDSAT scenes. The analysis based on derived land cover maps shows a 8.64% decrease of natural vegetation in the study area (715,094 ha) in 2001 relative to 1992. It is demonstrated that the methodology presented here provides reliable results and is fully applicable for the assessment of the environmental impact of large scale mining operations.

Jan 1, 2006

By Drupad B. Desai, C. C. Ku

INTRODUCTION The Laurens Street section of the Northwest Line of the Baltimore Region Rapid Transit System, located along Pennsylvania Avenue between Pitcher Street and North Avenue is situated in material which cannot be definitely categorized as soil or rock. However, in the area of residual soils in which these tunnels were constructed, considerable attention was required to determine the character of the ground so that the designers and the constructors could properly evaluate the behavior of the ground and plan their respective efforts accordingly. The Laurens Street sections structures consist of twin rock tunnels, station structure, traction power substation, vent shafts at both ends of the station, the midline vent shaft, and the twin mixed-face tunnels. This paper concentrates on the mixed-face tunnels which extend from Station 99+67.03 (O.B.) to Station 102+49.00 (O.B.) at the southern end of the section. Since the completion of the design of this project, the Laurens Street section has been renamed the Upton Station. (See Figures 1 and 2). SUBSURFACE INVESTIGATIONS At early stages, three preliminary studies were performed by the General Soils Consultant (Ref. 1, 2, & 3). The purpose of the first study was to ascertain the generalized geological and subsurface conditions which might be encountered in the region. No borings were performed for this study. A limited number of test borings were performed for the second study, which included subsurface data for the Northwest and South Lines of the Transit System. Three borings were

Jan 1, 1981

By M. Gershon

Four computerized approaches for coal blending are described and their strengths and weaknesses are explored. Spreadsheet analysis Other than word processing, spreadsheet software is the most commonly used software. Its wide availability and ease of use are two desirable features that have led many to try to adapt it to the purpose of coal blending. These are the two main advantages of this approach. To use a spreadsheet for coal blending, each row of data represents one source of coal. Each column represents a quality of the coal, with the last column specifying the tonnage of that coal in the blend. The calculated figures are. the blended qualities, which can be programmed to appear in the bottom row. A trial-and-error approach is then used to develop the best blend. Inserting any blend in the last column provides the blend characteristics at the bottom of the page. If any specifications are not met, the blend can be changed, all calculations being immediately updated. This process is repeated until all specifications are satisfied. A third advantage of this method is that it is exactly the procedure that one would go through if doing this by hand. With a spreadsheet, many more blends can be evaluated in much less time, allowing the designer to try to improve over satisfactory blends to find the best of them. The resulting improved blends or cost savings are a fourth advantage of this approach. There is only one major disadvantage of using the spread- sheet. This is that most probably the best blend is not found. As an inexpensive introduction to computer-assisted blending, which can be easily understood and cost just a few hundred dollars, this is a recommended place to begin.

Jan 1, 1987

By Kerby Glass, Glenn A. Gruber

Mr. C. A. Hollingsworth introduced commercial column flotation to the Florida Phosphate Industry in 1976, with a six feet diameter prototype cell at the Tenoroc Mine. More than two-dozen column cells have been installed in phosphate beneficiation plants since then. The increased interest in column cells for phosphate flotation, and their potential use in new plant construction, prompted the Florida Institute of Phosphate Research to fund programs to investigate various aspects of column flotation. This report describes a test program, conducted by JACOBS at CF Industries Hardee Complex II, as part of a comprehensive research program awarded to the University of Florida by the Florida Institute of Phosphate Research. The 1.5 feet diameter test column was operated with plant process water and plant reagentized flotation feed. Several variables considered for column cells design and operation were tested. Feed specific capacity, air superficial velocity, and the length to diameter ratio of the column were the variables that influenced phosphate recovery. Concentrate phosphate grade was influenced by concentrate superficial velocity and feed specific capacity.

Jan 1, 2002

By Slavoljub D. Maksimovic, Steve J. Page

The Bureau of Mines measured respirable dust emission rates from overburden drilling at a surface coal mine and the transport of this dust to downwind locations. The emission rates were estimated by using multiple gravimetric dust samplers mounted on a cross-shaped tripod located immediately downwind of the drill. The transport of this dust was measured at more distant downwind locations by a combination of respirable gravimetric sampling and integrated bag sampling of sulfur hexafluoride (SF6), which was used as a tracer gas. Two modes of sampling were used: (1) At five sampling locations arranged in a semicircle around the drill. The radius of this arc ranged from 15.85 m (52 ft) to 71.32 m (234 ft). (2) In-line sampling at downwind locations with samplers located at intervals of either 10.67 m (35 ft) or 15.24 m (50 ft) for a total distance of 76.20 m (250 ft). Samples were taken 1 .22 m to 1.52 m (4 to 5 ft) above ground level. Test results for the semicircular test arrangements showed that at any downwind location, the maximum contribution of respirable dust due specifically to the drilling operation was 42%; the average for eight tests was 13.6%. In general, there was no correlation between the downwind distance of this maximum contribution and the maximum contribution itself because of changing wind direction. Test results for the in-line arrangements indicated that the transport of the dust from the drilling operation usually decreases rapidly with distance and that, even though the drill dust may produce significant health hazards for the drill operator and drill helper (or other personnel in the immediate vicinity), the exposure of downwind personnel to drill-generated dust may not be a significant problem.

Jan 1, 1987

By Richard Newcomb

It is four years since the seminal study of demand for rapid excavation by the National Academies of Sciences (NAS) and Engineering outlined this technology's opportunities, requirements and significance to the challenges of urbanization and natural resource conservation. The demand study was quite simple. Opportunities were valued at market while requirements to produce new technologies were valued at cost. The significance of new technology in economic terms was measured by the net discounted gains to users over time. The Academy view in 1968 was that these gains, even most modestly estimated, appeared large enough to justify the bill for research proposed by that Committee (1). In 1970 the question of demands became international in what is recognized as the first international experiment in technological policy analysis, terminating in the Advisory Conference on Tunneling of the Organization for Economic Cooperation and Development (OECD)(2). A monumental demand survey formed the basis for its economic assessment. The twenty-two OECD nations also made an impressive attempt to measure the magnitude of existing research and development efforts. In their recommendations periodical statistical demand forecasting and collection of demand data (Recommendation 1) was given central importance for public planning (Recommendation 2), the financing of public construction (Recommendation 3) and the encouragement of technological advance (Recommendation 4). Their program for international cooperation led to OECD's establishment of a Directorate for Environmental Affairs, and influenced the organization of the World Environmental Conference meetings now held in Stockholm under United Nations auspices. The OECD Conference was the first example of "an attempt to apply the concept of technological policy analysis to a 'civilian' technology having potentially

Jan 1, 1997