Search Documents

By D. Sotiropoulos

In the recent years, the mining sector is looking for specific indices, taking into account economic, environmental and social criteria, in order to meet the sustainable development requirements. In the present study traditional and environmental sustainable indices used in the Agios Dimitrios Power Plant, Northern Greece, are compared to those of ESKOM Company, South Africa, taken as reference. These indices are referred to, a) the solid fuels consumption, such as lignite, and, b) the emissions to the atmosphere, such as SO2, NO2 and dust. Last five years data show a remarkable improvement of all indices in the Agios Dimitrios Power Plant. Although the lignite used in this Power Plant is by far of poorer quality than that used by ESKOM - net calorific value 1272 and 4638 kcal/kg, respectively - dust emissions in both Power Plants are similar (52 and 31 g/kWh, respectively). The SO2 and NO2 emissions are very low in Agios Dimitrios compared to those of South Africa, respectively 1.92 and 7.91, and 1.74 and 3.61 g/kWh. This is mainly due to natural desulfurization (by the lignite?s calcium content) and the low NOx burners.

Jan 1, 2003

By P. Arell, D. Folkes

This paper presents the basics of EPA’s Hazard Ranking System (HRS), which is used to evaluate sites for possible inclusion on the Superfund National Priorities List (NPL). The paper describes the surface water, ground water, air, and soil exposure pathways and how they are applied to mining sites. Key factors contributing to the site score include the likelihood of a release, waste characteristics, and the targets for each pathway. Waste volumes, definitions of landfills versus surface impoundments, and background concentrations are of particular importance to mining and smelting sites. Because of the presence of metals, large waste volumes, and observable releases, mining and smelting sites often receive high enough scores to be proposed for the NPL based on a single path-way. Neverthess, owners and operators can take steps to reduce the risk of being scored, and to reduce the potential for high scores.

Jan 1, 2004

By S. K. Kawatra, T. C. Eisle

In froth flotation of phosphate, it is important that the flotation be as selective as possible in order to maximize grade and recovery without adding additional stages of flotation. Flotation columns provide a means for improving the selectivity compared to conventional flotation machines and are of considerable interest for phosphate processing. The selectivity of a flotation column is largely limited by the degree of back mixing of tailings into the froth zone, and its recovery is limited by the degree of short-circuiting of feed to the tailings. The horizontally baffled flotation column was therefore developed to minimize back mixing and short-circuiting without introducing problems with plugging or reduced capacity. The introduction of horizontal baffles to a column reduces both entrainment of feed water into the froth and short-circuiting of feed to the tailings, which improves the column selectivity. The results of horizontally baffled column flotation of phosphate are presented for fatty acid flotation of phosphate, with comparison to conventional flotation using the same reagents.

Jan 1, 1999

By S. D. Thompson

Several discrete-event simulation models have been developed for designing the conveying system capacities of underground coal mines. Most of these models require the use of a step function approach to mimic the loading process at each conveyor loading point. Over the years, practitioners have generally employed one of three versions of the step function approach. An important issue is how these three versions compare to each other in terms of simulated capacity requirements for belt conveyors. Another issue is how they compare to the peak capacity design. This paper addresses these issues by statistically and quantitatively comparing their simulation results. The consequences and problems associated with using each version are also discussed and summarized.

Jan 1, 1998

By Lynn B. Hales, Randy A. Ynchausti

There is a large economic driving force associated with improving metallurgical performance in mineral processing plants using process control. Because of this and other benefits, control systems of the future will develop towards more sophisticated user friendly computer based systems that use powerful software analysis and control techniques. Auto-tuning, adaptive control and process models will gain expanded use because of their transparent availability to the system designer. Control of individual unit operations will be optimized and coordinated through expert systems that monitor economic conditions and management directives and direct operations accordingly. Plant areas, considered cost centers for years, will be integrated into plant-wide control systems for economic control and optimization. New control hardware, process sensors, control strategies and software development tools will be presented, as well as an overview of the economics driving the continued development of advanced process control systems.

Jan 1, 1993

By Julian Boldy

The discovery of the Delbridge massive sulfide deposit in the Noranda district of Quebec resulted from an appreciation of the significance of a mercury leakage haloas a lithochemical pathfinder to blind ore, coupled to its location relative to a geologically inferred ore-bearing horizon within complex volcanic stratigraphy. Systematic sampling of microfractures present in outcrops delineated a diagnostic anomaly, drawing attention to an area considered prospective for buried ore. The massive sulfide deposit was subsequently found to be blind and topped at the 107-m (350-ft) level. This case history is presented in the context of its time and was the first volcanogenic ore deposit to be discovered utilizing mercury as a pathfinder in the Canadian Precambrian. The case history also illustrates that the practical application of an innovative technique coupled to a new geological interpretation can result in success, even on a property that was centrally located in a mining district and had undergone intensive exploration efforts over a 38-year period.

Jan 1, 1991

By Jean-Michel Rendu

Equipment capital operating costs represent a significant portion of the total cost of most mining operations, and a variety of computerized methods have been developed to assist in the selection and effective use of this equipment. The questions to be answered and the tools available to answer these questions vary with the type of mine to be analyzed, the stage of development of the mining venture, the size of the operation, the details required, and the technical or economic objectives to be reached. Even though a majority of publications are directed towards open pit mining operations, the underground environment is not neglected. In the early planning stages of a mining venture, equipment selection is the problem to be solved. The simplest computer systems are designed to' automate time consuming manual tasks. A data base is supplied to and maintained by the user, which describes the technical and economic characteristics of available equipment. The user specifies the physical environment within which the equipment will be used and chooses from the data base a combination of loading and transport equipment. The role of the computer is to detemine the production which will be likely reached, the associated costs, and other relevant statistics. This approach is most helpful when modeling small operations or isolated parts of larger operations.

Jan 1, 1989

By P. Somasundaran

Beneficiation by froth flotation, which exploits the difference in surface properties of minerals, has been a promising method for coal cleaning. However, dissolved mineral species present in coal flotation systems can interact with particles and other species leading to drastic effects on flotation. Particularly, precipitation or adsorption of such species on the particles can alter their surface properties and thus influence the efficiency of coal cleaning. In this work, the bulk and surface precipitation of the dissolved mineral species present in Pittsburgh No. 8 coal was investigated under controlled experimental conditions. Changes in the surface properties of coal due to the precipitation were monitored by following zeta potential. Solution potential data were used to elucidate the mechanism of the precipitation. The effect of the precipitation of the dissolved species on the floatability of coal was found to be marked.

Jan 1, 1995

By D. Limpitlaw, E. M. Hoadley

The minerals sector plays a significant role in the development of many Southern African economies. In the Southern Africa region, as in other developing regions, economic development is seen as the key contributor to poverty alleviation and social upliftment. The significant economic contribution of the minerals sector may be reduced by negative impacts on the biophysical environment and on the communities where mines operate. A critical variable in determining the net contribution of mining companies to SD is the degree of transparency with which the companies operate. Transparency is increasingly emphasised as an essential aspect of good governance and SD, but it is also difficult to establish, and is a sensitive issue for mining companies as they compete with each other for minerals sales. Transparent reporting could ensure that the interests of all stakeholders are addressed as company data is subject to informal ‘auditing’ by any interested party. This paper assesses published reports of five companies over a number of years to establish whether it is possible to make an assessment of the companies’ contribution to SD.

Jan 1, 2005

By Greg P. Timms, John W. Bennett

Monitoring on Whites waste rock dump at Rum Jungle has provided a unique opportunity to assess the effectiveness of a cover in the medium term. Temperature and oxygen concentration profiles have been measured continuously, from some years before the cover was put in place in 1983 until the present. Lysimeters have been used to measure water infiltration rates. Heat and oxygen transport processes in the dump have been modelled and compared with field data, enabling oxidation rates to be quantified both before and after the cover was put in place. It has been found that the cover reduced the overall oxidation rate to between one third and one half of the uncovered rate. There is evidence that both the overall oxidation rate and water infiltration rate have increased in recent years.

Jan 1, 2000

By Steven W. Hunt, Ronald E. Heuer, Safdar A. Gill

A 3.3 m (11 feet) diameter, 51 m (168 feet) deep temporary steel casing which had been sunk within glacial soils buckled and collapsed on July 29, 1985. The collapse occurred at the CT-8 Dropshaft site in Milwaukee while two workmen were contact grouting outside the casing in an attempt to stop groundwater inflows through a bottom plug. This paper describes the soil and groundwater conditions at the site, the casing design, the method of shaft construction, and probable causes of the buckling failure. Specific aspects of the paper include: slurry method of shaft excavation and casing installation, soil creep, earth pressure due to three dimensional arching, and buckling strength of a casing surrounded by slurry rather than grout and firm soil. The paper should be of interest to designers and constructors of temporary ground support systems for deep shafts.

Jan 1, 1995

By S. D. F. Rocha

The influence of surfactants on the crystallization of calcium sulfate was investigated in both hatch and continuous systems. The investigation was per formed at the following conditions. 343 °K, 28% P205 and with a sulfate level of 2.0%. At concentrations of 5 and 200 µgig, respectively, dodecylbenzene sulfonic acid (DBSH) and sodium diisooctil sulosuccinate (SSNa) promoted both an increase in the size and a reduction in the length/width (L/W) ratio of the calcium sulfate hydrates produced in the hatch and continuous crystallizers. Unique effects were observed in the batch system at higher DBSH concentrations. At 10 µg/g, the precipitation of hemihydrate crystals with a distinct morphology and texture occurred under conditions where dihydrate precipitation was expected. Above 50 µg/g, the precipitation of calcium sulfate hydrates was completely inhibited.

Jan 1, 1996

By R. Hogg, T. F. Dumm

A simple shape description scheme has been developed which has the specific aim of distinguishing between angular and more rounded particles. The procedure involves fitting a general polygon (usually about 20 sided) to the particle profile. Geometric shape descriptors have been defined based on variations in the angles between adjacent sides and their radial displacement from the particle centroid. A two-parameter shape description, incorporating an angular variabli1ity and an elongation index, has been shown to be clearly consistent with visual observations. A single-parameter angularity index has been shown to be very sensitive to small differences in particle roundness and seems to provide a better description of angularity than other approaches such as signature and fractal analyses. The scheme has been applied to three sets of fine quartz particles produced by different grinding procedures. The results indicate that the technique is capable of distinguishing between angular and re1atively rounded particles and can quantify their specific shape features.

Jan 1, 1991

By R. G. Reddy

Chemical and structural changes occurring during the roasting of refractory gold ores were investigated. Effect of temperature on oxidation behavior of ores was analyzed using TGA, DTA and X-ray diffraction methods. The experimental results showed that the carbon in the ore has to be oxidized to a minimum value before any appreciable oxidation of sulfur occurs. Oxidation rates as a function of temperature were calculated. Optimum conditions under which a successful roasting of the refractory gold ores can be obtained are discussed.

Jan 1, 1990

By P. C. Thakur

The history of coal mining in the United States of America and the rest of the world is replete with mine explosions and consequent loss of lives. Serious efforts in the USA to recover methane prior to mining and post mining started about forty years ago. CONSOL Energy Inc. and government agencies, e.g., the erstwhile US Bureau of Mines developed several techniques of methane drainage, such as in-mine horizontal drilling, vertical gob wells, hydrofracing of vertical wells and horizontal drilling from surface. With the current technology, thirty to sixty percent of total methane emissions from a mine can be captured making the mines much safer and more productive. Drained methane is often marketed to defray the cost of methane drainage. This paper is an anthology of these developments and describes how coalbed methane, which used to be a bane, has become a boon for the coalmining industry.

Jan 1, 2003

By ev, Ze&apos Reches

The growth of networks of shear fractures is explored in a series of experiments with samples of wet clay. The samples are subjected to plane strain deformation in a rigid apparatus. The individual fractures observed on the upper surface of the clay samples grow longer by three mechanisms: in-plane propagation, off-plane propagation and coalescence. New, active fractures cut and displace older, less active ones. The lengths of individual fractures display lognormal distribution in most cases and power distribution in fewer. The calculated length parameters in the experiments, as well as in three field cases discussed here, suggest that the fundamental parameters in fracture analysis are the normalized cumulative length and the length of the shortest fracture measured.

Jan 1, 1986

Development of computer-based information systems is predicated on the merger of rapidly developing computer technology and growing managerial demands for information. The focus of this section is on managing the development and implementation of information systems for the 1980's. It is the experience of the majority of contributors to this volume that among unresolved problems of major dimensions in a mineral organization are those of managing the computer-based information systems resource itself. There are three major reasons for this: (1) mineral information systems are relatively new to the senior management of a mining company or a mineral organization; (2) problems are compounded by a developing technology, a new type of personnel with a changing experience/education mix; and (3) an organizational structure and location which, in many organizations, are still being examined. The three authors in this section present aspects of managing the information systems function which, based on their experience, are common to the solution of the problem. The premise that the information systems function has been placed appropriately within the entire business plan of the firm has been made by the authors in their discussion of the various aspects of the management process.

Jan 1, 1979

By Wilhelm J. Kogelmann

The concept and operation of novel shaft sinking systems utilizing roadheader-type cutter booms, including mucking, conveying, and hoisting installations, are described. Selection criteria, performance data, and economic considerations for various shaft excavators are presented. Various applications of this low-cost and flexible system for civil engineering and mining projects will be discussed. The cutter booms can work in both soft ground and competent rock. Furthermore, the novel excavator can operate in ground stabilized by grouting, cementing, and freezing. The flexible cutting system can be used both for excavation of shafts, foundation pits, slopes, and for tunneling (drifting).

Jan 1, 1989

By Shuji Owada, Keisuke Yasukawa

Electrostatic and/or high tension separation has been used for the separation of rare metal bearing minerals, foods, industrial wastes and so on. Since the separation is achieved by the difference mainly in surface conductivity of particles, the efficiency in humid circumstances is very low, and then, the applicability is considerably limited. We applied the following two-stage pretreatment technique to the separation process, which involves (1) adjustment of surface wettability by adsorbing surfactant on the particle surface and (2) control of the surface conductivity by spraying with electrolyte aqueous solution. The addition of this pretreatment technique has been found to have a great advantage over conventional methods. Separation efficiency is achieved even in humid circumstances and selectivity can also be obtained between insulator minerals. The selectivity is very similar to that of flotation in wet process. This separation technique will be applied not only to mineral processing but the processing of industrial waste such as electric and electronic waste materials.

Jan 1, 1995

By Robert Jedrzejczak

The Endako Mine is an open-pit molybdenum mine located in the north central region of British Columbia, Canada, about 960 km (600 road miles) north of Vancouver. Production for the latter part of 1992 was expected to averaged 63.5 kt/d (70,000 stpd). Of that amount, 27 kt/d (30,000 stpd) was the mill feed. This production is achieved with five 11.5 to 14.5 m3 (15 to 19 cu yd) electric shovels, six Euclid R190 and two Unit Rig M120 diesel-electric haul trucks, and three 320 mm (12.25 in.) electric rotary drills. There are three ore zones delineated into pit areas: the Endako, Denak East and Denak West. Present mill feed source is the southeast stage of the Endako Pit. Stripping is carried out in the south wall stage also of the Endako Pit. The mine high grade aggregate is reduced in the primary and secondary crushing circuits before processing in conventional RM-BM-flotation circuits. The majority of the molybdenum sulfide (MoS2) is roasted on site to produce technical grade molybdenum oxide (M003). A portion is further refined and treated to yield a 99.9% pure MoS2 product.

Jan 1, 1993