Search Documents

By Greg Barfoot, Kurt Keskimaki

The Henderson Mine is located approximately 50 miles west of Denver, Colorado. A project is underway to replace the existing rail system which transports molybdenum ore 15 miles from the mine to the mill using three flight conveyor system. The first conveyor is a 1 mile, high lift conveyor which transports the ore from an underground crushing station to the end of the existing rail tunnel. The second conveyor is 10 miles in length and utilizes the existing rail tunnel to transport the ore from the mine, which is on the east side of the Continental Divide, to the mill located on the west side. The third conveyor takes ore from the tunnel portal to the mill through a series of 7 horizontal curves and inclines up to 15 degrees. The project applies advanced conveyor design to tackle the installation of the system in an operating mine and achieve the highest possible level of reliability. This paper outlines the design process for this system, discusses the options which were evaluated and how the current design evolved.

Jan 1, 1998

By John W. Ahlrichs, E. Daniel Baker, Erich U. Petersen, William J. Tafuri, Douglas N. Halbe

The combined Bootstrap and Capstone deposits, located in the Bootstrap subdistrict (Section 10, T36N, R49E, M.D.B.M., Elko County, Nevada), are approximately 27 miles northwest of Ca-1I: Nevada. The contiguous Bootstrap Capstone deposits are located along the northeastern and northern flanks of Round Mountain, a horst block separated by grabens from the sheep Creek Mountains to the north-northwest and the Tuscarora Mountains to the east. Open-pit-minable gold reserves as of December, 1989, were 13.27 million short tons with an average grade of .057 troy ounces gold per ton and an overall waste-to-ore strip ratio of 2.5:1. Ore zones in Bootstrap are concentrated along north striking high-angle dikes localized along faults, while ore zones at Capstone are strata form and structural, occurring at the Devonian limestone/siliceous sediment interface and in high-angle fault-filling dikes. Pre-ore faulting produced a complex structural setting for Capstone, dominated by strong northwest fault sets cross-cut by northeasterly structures. Alteration associated with both deposits is silicification with a-strong argillic overprint. Dike emplacement, which post-dates silicification, marked the onset of mainstage gold deposition and argillic overprinting of silicified lithologies. Gold displays an affinity for moderately argillized sedimentary and igneous lithologies. Mineralogic and geochemical analyses of rotary percussion drill samples show good correlation between gold, silica, antimony, and arsenic.

Jan 1, 1990

By Van Zyl Brink

A longwall-based coal mine in Australia, referred to in this paper as AusMine Colliery, experienced windblasts resulting from goaf falls. Windblasts were the cause of serious injuries and threatened the continued operation of the mine. A microseismic early warning system was installed and a significant success rate in providing early warning of large roof instability resulting in high velocity windblasts, has been achieved. Early warning of goafing is accepted as an operational tool on the mine. Severe demands are placed on the operator in terms of 'real time' interpretation. The development of an expert system allowed for a probabilistic approach to achieve automatic alarms. This paper will quantify the success, failure and false alarm rates achieved by manual operation and automatic expert system-based decisions making, respectively.

Jan 1, 2002

By M. Polat, G. Ahuja, S. Chander, M. S. Klima

A study was conducted to investigate the use of flotation in combination with dense-medium cycloning utilizing ultrafine (-10 um) magnetite, as an integrated process for high-efficiency cleaning of fine coal. The objective was to produce a high-quality (low-ash, low-sulfur) coal, while reducing the amount of non-magnetic material that would need to be removed by magnetic separation. Three dense-medium cyclone tests were performed using different underflow diameters to produce feed material for the flotation separations The use of different underflow configurations caused a variation in the pulp and solids splits, which changed the clean-coal yield and the magnetite-to-coal ratio of the cyclone products, and hence, the composition of the flotation feed. Flotation was used to separate the clean coal and to recover the magnetite contained in the cyclone overflow stream. Any ultrafine refuse material, which may have reported to the cyclone overflow stream, was also removed in this step, further upgrading the product. In addition, flotation was used to improve the overall yield by recovering a middlings fraction from the cyclone underflow stream. It was found that flotation was very effective in separating the coal (or middlings) from the ultrafine magnetite, even under variable feed conditions. Magnetite recoveries approaching 99% were possible using rougher-cleaner separations in a laboratory flotation cell. This paper presents the results from this study.

Jan 1, 1995

By Michael J. Sapko, Robert A. Cortese

A flame powered trigger device has been developed to explosively activate suppression barriers to quench gas and coal dust explosions. The important feature of the device is a silicon solar panel, which collects 0.3 p to 1.1 D wavelength radiation from the developing explosion, and generates electrical energy to initiate a detonator, which in turn causes the rapid explosive release of an extinguishing agent into the advancing flame front. Solar panels that are rated to produce 20 w of electrical power when exposed to the sun light are producing about 200 w when exposed to full-scale dust explosion propagating in the U.S. Bureau of Mines' Lake Lynn Experimental Mine. The solar panel is electrically isolated from the detonator by a pressure sensitive switch until the arrival of the precursor pressure pulse, which always precedes a deflagration. This combination of pressure arming and flame powered photo generator prevents false barrier activation and requires no external power supply.

Jan 1, 1991

By H. Soto, J. Jara, F. Nava, J. B. Hiskey, B. J. Scheiner

Laboratory tests showed that ozone can destroy free cyanide and weakly complexed cyanide (copper and zinc cyanides). The iron cyanide complexes were resilient to ozonation but they were effectively eliminated by precipitation with Fe (II) ions under controlled pH conditions. Tests carried out with effluents from a number of gold mills confirmed the results obtained previously in the laboratory. The industrial samples contained cyanide in the form of free cyanide and also complex copper, zinc and iron cyanides. Solutions that contained up to 184 mg/L total cyanide, after the ozone treatment analyzed only 2-3 mg/L dissociable cyanide and 50-90 mg/L CN(t) (accounted for by iron complexes). After precipitation with ferrous ions total cyanide was reduced below 1.5 mg/L. For most solutions ozone consumption ranges from 3 to 6 g per g of cyanide destroyed. However, certain impurities (such as SCN and S203 ), present in some effluents, increase ozone consumption and make it more difficult to reduce copper concentration to satisfactory levels.

Jan 1, 1993

By B. Rao Pothini, Julio H. Thaler, W. L. Finlay

The White Pine room-and-pillar mine started in 1955 from a suboutcrop, down gentle dips, and with a competent sandstone roof. As mining depths increased, extraction decreased 1% every 35 feet. Moreover, roofs became shaly and less competent, and regions of high fault and joint densities, sometimes with and some- times without high lateral stresses, increased the tendencies towards roof falls. Instinctive reactions towards narrower openings did not alleviate the problem. Careful consideration of rock mechanics principles culminated in the development of two variants to the conventional room-and-pillar mining system based on the concept of stress relief through load deflection. The two systems-EquiAdvance Cave, and PressureArch Panel Mining-are complementary. The objective of the former system is to provide relief from lateral stresses through advance caving and in the process also to achieve higher extraction at depth. Where surface subsidence cannot be allowed, the alternative PressureArch Panel concept is utilized to provide stress relief and moderately high extraction ratio. Both systems have been under trial for over three years and, together, produced over three million tons of copper ore. These two systems, and their production test results to date, are described.

Jan 1, 1977

By Richard H. Gates

INTRODUCTION The U. S. Army Corps of Engineers is developing chemical explosive excavation as a construction technique for use on Civil Works projects. Large chemical charges are being used in multiple charge arrays in a variety of media and topographic situations to achieve actual construction projects. The target is the development of chemical and nuclear explosive excavation as an accepted cost-competitive construction technique. Military research using explosive excavation is also being conducted to apply this technique to military engineering for combat purposes and to military construction. The information gained from both the civil and military research is integrated into the overall development of explosive excavation. This research and development work is being conducted under the auspices of the U. S. Army Engineer Waterways Experiment Station Explosive Excavation Research Laboratory (EERL) located at Livermore, California. This organization was formed in 1962 as the Nuclear Cratering Group (NCG) to carry out the Corps of Engineers (OCE) portion of a joint agreement with the Atomic Energy Commission (AEC) to develop nuclear explosives for construction purposes. The AEC, through the Plowshare Division of the Lawrence Livermore Laboratory at Livermore, California, has been responsible for developing nuclear explosives, conducting nuclear cratering experiments, developing nuclear safety information, and developing methods for predicting the shape of the craters. The Army part of the program includes corollary chemical high-explosive cratering experiments, participation in the AEC's nuclear cratering experiments, and development of

Jan 1, 1997

By Richard A. Williams

The design, modelling and simulation of solid-liquid mixers remains one of the least advanced aspects of minerals processing, due to difficulties in quantifying complex slurry hydrodynamics from first principles, and in acquiring reliable experimental data for model verification and development. This contribution describes the application of electrical resistance tomography (ERT) for three dimensional imaging of the concentration of mineral particulates in a slurry mixer as a function of key process variables (particle size, impeller type, agitation speed). It is demonstrated how ERT can provide a wealth of detailed data to allow model development, which ultimately will lead to much improved design capabilities and the generation of mixing models which could reside within Particle Process Simulators. This principle is illustrated using descriptions of mixer behaviour based on an empirical approach, although the measurement methodology described is equally suited to development of computational fluid dynamics models, cellular models or design approaches based on artificial intelligence. The experimental data can be built into a visualisation data bank, which acts as a "process toolkit" by allowing a library of process responses to be catalogued. Hence these data can be accessed for the purposes of model development, equipment selection, optimisation of operating conditions or testing on-line control strategies.

Jan 1, 1995

By P. C. Cochrane, I. S. Clelland, S. H. E. Phillips

Geological and hydrological conditions in the strata overlying the Salado Formation vary considerably in the Carlsbad, NM, area. The first four shafts sunk at International Minerals and Chemical Corp. (IMC) property have been located in competent and essentially dry conditions, while other shafts on adjacent properties have had such adverse conditions that ground freezing has been chosen as the water and ground control technique for shaft sinking. At the location of the IMC No. 5 shaft there has been extensive erosion and salt dissolution in the Rustler Formation, leading to collapse of some zones of the strata. Both ground freezing and pregrouting were considered as alternative methods of stabilizing the extremely poor ground conditions and controlling the potentially very heavy water inflows. It was decided that pregrouting the shaft was feasible and would offer substantial cost and time saving over a ground freezing technique. This paper describes the pregrouting techniques used and illustrates the requirement for flexibility in a grouting program so that it can be modified to reflect any new or additional information obtained during the progress of the grouting.

Jan 1, 1987

By K. M. Belingheri, M. E. Smith

Pinson Mining Co. operates a conventional mill and two heap leach operations in north-central Nevada. The latest of these heap leach operations, the Preble project, is a low-grade, low-tonnage property made profitable through several innovative capital reduction techniques. Rapid return on investment was a prime factor in design. To facilitate this, fast-track design and construction techniques were employed. The project is a seasonal 1.5 kt/d (1 700 stpd) crush/agglomerate heap leach plant using both clay and plastic leach pads. Construction and startup were achieved through cooperative arrangements between local contractors and in-house construction personnel, with few items put out to bid. An interactive approach to design minimized lost time and construction costs.

Jan 1, 1987

By W. J. Wuest, M. J. DeMarco, J. R. Koehler

Yield-pillar-based gate-road designs often fail to provide mine operators with adequate ground control. This is because of the unknowing m is employment of "critically" sized pillars. A "critical” pillar is one that is too large to either yield nonviolently or to yield before the roof and floor sustain permanent damage and is too small to support full abutment loads. To demonstrate the critical pillar concept, afield study of a tapering gate road was conducted by the US Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m (55.1-ft) wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m (40-ft) wide design more closely approaches proper yield pillar dimensions. A probe hole in several 10.6-m (34.8-ft) wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1997

By D. A. Swanson, G. Danziger, G. Savci, C. Barnes

Hydrologic assessments of existing and proposed waste rock stockpiles are typically required for application of operating and closure permits at mine sites. A hydrologic assessment should include an evaluation of climatic data and prediction of the net infiltration rate through the waste rock stockpile surface. In addition, hydrologic factors such as the time required to deplete available moisture storage in the stockpiles and the time required for potential seepage to migrate to the underlying aquifer should also be predicted.

Jan 1, 2000

By S. Chander

Neutralization of acidity by addition of alkaline materials is a commonly used method to treat acid mine drainage. However, this procedure requires large amounts of reagents based on acid-base accounting. The potential use of organic additives in preventing or ameliorating acid mine drainage was investigated in this research. The tests were conducted in weathering columns using refuse samples from a coal cleaning plant. Both cationic and anionic compounds were tested. For a comparison, tests were made in the presence of limestone and lime. The results show that some of the reagents substantially retarded the rate of oxidation whereas others even enhanced it. The suppression of the rate of pyrite oxidation was ascribed to surface chelation. Formation of surface compounds prevented the pyrite particles from further oxidation. Such a treatment required only small quantities of reagents since the reaction was confined to the surface.

Jan 1, 1992

By R. J. Pugh

The surface chemical sites on several fillers (quartz, feldspar, calcite and granite) were studied by the adsorption of well defined acid and basic probe molecules (benzoic acid, benzyl alcohol, ethyl benzoate, pyridine and benzyl amine) from cyclohexane. The results provided a wide variation of adsorption data, emphasizing the extensive range of site heterogeneity on the filler surfaces. In addition, it was shown that the acidic probes were strongly adsorbed on all of the minerals, thus indicating that the basic surface sites dominate the acidic ones. Also, through FTIR studies with vapor-phase probes adsorbed on orthoclase, it was possible to identify the nature of specific sites and the type of bonding occurring between the filler surface and the probe molecule. These types of surface analytical techniques could give useful information for predicting the adsorption functional groups on dispersants, dyes, thickeners, etc. and could lead to enhanced interfacial bonding between the filler and the matrix.

Jan 1, 1993

By B. Moudgil, Hassen El-Shall

Particle shape and size distributions are among the most important parameters that affect the filtration efficiency of phosphogypsum in wet- process phosphoric acid production. Cost-effective enhancement in filtration rate is desired by phosphoric acid producers for higher plant capacity and lower operating costs. In this regard, numerous research efforts have been carried out in different laboratories as well as in pilot and plant testing. Nevertheless, changes in phosphogypsum crystal shape and size distribution deserve special attention. In this study, the results obtained in the presence of Crysmod and Hiflo-S5 surfactants are discussed. The influence of such additives on crystal morphology and size distribution are studied under different sulfate contents (supersaturation). The obtained data are correlated with process efficiency parameters such as filtration rate, digestion of rock, and recovery of phosphate values. Up to 60% increase in filtration rate is obtained. In addition, an increase in digestion efficiency and P205 recovery is achieved due to addition of surface active agents. The observed beneficial effects are explained in the light of the changes induced in crystal habit, size, and size distribution.

Jan 1, 1999

By E. J. Beckman, R. M. Enick, C. Powell

Liquid carbon dioxide can be used as a replacement for organic solvents in the extraction of anionic platinum group metal complexes from an aqueous phase. However, because conventional extractant-metal complexes are not soluble in liquid carbon dioxide, this can be achieved only if highly carbon dioxide-soluble extractants are developed. For example, trioctylamine-gold chloride is not soluble in liquid carbon dioxide, although trioctylamine is CO2 soluble. The novel CO2-soluble extractants presented in this paper have a CO2-philic fluorinated tail to enhance solubility and a conventional amine head group for extraction of metals. Both the extractant and the extractant-metal complex are soluble at ambient temperature at pressures from 7 to 35 MPa. Efficiency factors as high as 2.23 have been measured using 1,1,2-trichlorotrifluoroethane (TCTFE), a low pressure screening liquid for carbon dioxide, indicating that these compounds will strongly bind the metal chloride. For example, 84% of Pt-chloride was extracted into TCTFE using a 3.5:1 ratio of a double¬tailed fluoroalkyl amine extractant: metal chloride. An 88% recovery of Pt-chloride into high-pressure liquid carbon dioxide was achieved using the same extractant at a 3.5:1 ratio. Therefore, it appears possible to replace organic solvents with liquid carbon dioxide during the extraction of platinum chlorides if highly carbon dioxide-soluble extractants agents are employed.

Jan 1, 2002

A new separator, known as the HydroFloat cell, was developed to overcome the limitations of traditional flotation cells in recovering coarse particles. The HydroFloat cell separates particles based on differences in mass after the selective attachment of air bubbles to the hydrophobic component of the feed stream. Proof-of-concept testing, utilizing phosphate matrix, heavy mineral sands and anthracite slag, indicated that significant improvements in separation efficiency can be achieved using this air-assisted teeter-bed system. Based on the encouraging laboratory results, a pilot-scale HydroFloat cell was fabricated and installed at a central Florida phosphate plant. Test data collected using the pilot-scale unit suggest that the BPL recovery of the +35-mesh plant feed can be increased by snore than 40% through the application of this new technology. This improvement is particularly beneficial due to the very high grade (-73% BPL) of the +16-mesh particles in the HydroFloat concentrate. This article describes the theoretical basis for the development of the HydroFloat cell and provides an overview of recent laboratory and pilot-scale test results.

Jan 1, 2002

By Thomas P. Meloy

As the importance of particle shape in mineral processing is increasingly recognized as an major variable in predicting the behavior of both individual particles and particle systems, whether it be in dense media, froth flotation, comminution or the flow of particles, new method of shape characterization are being developed, particularly for use on image analyzers. These shape characterization methods may be broadly classified into the analytical, empirical and physical formation methods. Discussed are approaches and the strengths and weakness of each of these methods. Moreover old and new shape measuring techniques are reviewed, particularly the new image analysis methods techniques such as Fourier, Haar, Fractal, Walsh and Delta as well as a variety of other techniques such as tabling, the Cascadograph, settling and L/D ratios. Also discussed are the problems of doing shape research, current progress and the future of the field.

Jan 1, 1990

By F. K. Letowski

Leaching of zinc sulphide concentrate by nitric acid which is simultaneously regenerated by oxygen in the reactive froth has been investigated. The reactive froth was formed by a recycled zinc sulphate electrolyte containing nitric acid, a mixture of gaseous 02 and NOx, entrapped in the foam and particles of the zinc concentrate suspended in the foam. In the reactive froth the multiple regeneration of nitric acid proceeded owing to the encapsulated oxygen and amount of nitric acid used can be considerably lower than in the continuous liquid phase. 93 to 97% of zinc was extracted to a solution containing 30 to 409/1 HNO, during 40 to 60 min of leaching in a batch reactor without regeneration of nitric acid. 50 to 100% of the consumed nitric acid was regenerated during continuous leaching in froth carried out in the ‘flotation column’-type reactor at 80 to 90°C and under pressure of 100 to 200kPa. The rate of HNO, regeneration in the froth was proportional to oxygen pressure and inversely proportional to nitric acid concentration in the froth. A two-stage process flowsheet is proposed. In the first, the reduction stage, removal of nitric acid from the leach solution directed to standard purification and electrolysis is carried out by its reduction to nitric oxide using fresh concentrate in the froth. In the second, the oxidation stage, nitric acid is continuously regenerated by oxygen in the froth.

Jan 1, 1995