Search Documents

By C. Wade, A. Swart, M. Dworzanowski

AngloGold Ashanti operate a pyrite flotation plant at their East Gold Plant, Acid Plant and Flotation Plant (EGAF) metallurgical complex within their Vaal River operations in the North West province in South Africa. The flotation plant feed is reclaimed pyrite rich tailings and the concentrate produced is used as the source of sulphur for the EGAF acid plant. The sulphuric acid produced is in turn used for the recovery of uranium at the Vaal River South uranium plant. The original flotation plant built in 1960 was based on the use of many small volume flotation cells and was becoming very expensive to operate and its age severely limited further operation. A decision was taken in 2005 to replace this plant with a new one based on fewer, larger volume flotation cells. This paper describes the benefits of using larger volume flotation cells in this new flotation plant when compared to the smaller volume flotation cells in the old plant. The benefits of the new plant include a smaller plant footprint, fewer flotation cells, fewer pumps, no distribution boxes, simpler piping, a greater flotation volume and a reduction in installed power. The saving in capital cost could not be quantified because of the age of the old plant. The savings in operating cost will arise from fewer operators, less maintenance and reduced power consumption. The new plant has not been in operation long enough to quantify the benefits in operating cost and metallurgical performance. However, recovery improvements can be expected given the greater flotation volume (increased residence time) and the installation of larger, more efficient flotation cells.

Jan 1, 2007

By Y. D. Lee, J. H. Park, D. S. Kim, H. S. Song

The viscosities and the infrared spectra of the CaO-SiO2-MgO-CaF2(or Al2O3) slags were measured to enhance our understanding of the interrelationship among the thermophysical property, microscopic structure, and chemical thermodynamics of molten slags. The structural role of CaF2and Al2O3in the calcium silicate melts can be explained by a change of the degree of polymerization (DOP). The effect of CaF2on the viscous flow of molten slags is based on a decrease in the DOP by F-as well as by O2-ions and this was confirmed by the infrared (IR)spectra of the quenched slags. The effect of Al2O3on viscosity increase can be understood from an increase in the DOP by the incorporation of the [AlO4]-tetrahedra into the [SiO4]-tetrahedral units and this was also confirmed by the IR spectra. An amphoteric behaviour of Al2O3in the aluminosilicate melts could be correlated to the effect of ionic species of alumina, that is [AlO4]-tetrahedra and [AlO6]-octahedra, on the stability of silicate polyanions by taking the activity coefficients of slag components into account. Keywords: viscosity; infrared spectra; degree of polymerization; amphoteric behaviour; stability; activity coefficient

Jan 1, 2004

By A. Varadarajan, M. Hashemi, K. G. Sharma

Quartz mica schist collected from Nathpa-Jhakri Hydropower Project, Himachal Pradesh, North India is tested under triaxial loading using a servo-controlled loading system. Complete stress-strain-volume change behaviour including post peak softening behaviour of the samples, are presented. Strength and deformation parameters are given. Quarz mica schist, der von Nathpa Jhakri Hydropower Projekt, Himachal Pradesh gesammelt wird, wird Nördlich Indien unter triaxial geprüft, der von Gebrauch eines servo kontrollierten Ladesystems beladung. Vollständiges Spannung-Spannung-Band Änderung Verhalten Postens Spitze Erweichung Verhaltens der Proben, wird überreicht. Kraft und Verformung Parameter werden gegeben. Mica à quartz schist recueilli du Projet de Hydropower de Nathpa Jhakri, Himachal Pradesh, l'Inde du nord est essayé sous l'utilisation de chargement de triaxial un système chargeant servo réglé. La tension complète-la tension-comportement de changement de volume y compris la poste sommet amollir le comportement des échantillons, sont présenté. Les paramètres de force et déformation sont donnés.

Jan 1, 2003

By A. Golshani, M. Oda, K. Suzuki, T. Takemura

Anisotropic behaviours of OhshimaOshima granite were investigated by carrying out uniaxial compression tests, together with observations of microcracks under an optical microscope. The elastic modulus tensor of Oshima granite at 10 per cent strength,E10, were calculated using theoretically formulation of elastic modulus tensor in terms of the second-rank crack tensor for pre-existing open microcracks. Furthermore, with the assumption of orthorhombic elasticity, the nine moduli of Oshima granite E10were determined by uniaxial compression test. Twenty-onemoduli of samples, calculated without assuming any symmetry, also showed orthorhombic features. Direction of the symmetry axes agreed well with the orientation of preexisting cracks. Comparison of crack tensor-based formulation results with the experimentally determined one show that the anisotropy of elasticity of Oshima granite is caused by pre-existing open microcracks, not by pre-existing healed microcracks and also crack tensor formulation can be used, as a first-order approximation at least, to describe the anisotropy of Oshima granite induced by pre-existing open microcracks. ZUSAMMENFASSUNG: Das anisotrope Verhalten des Oshima-Granits wurde mit Hilfe voneinachsigen Kompressionstests und durch die Betrachtung von Mikrorissen unter einem optischenLichtmikroskop untersucht. Das Elastizitätsmodul von Oshima-Granit bei 10 Prozent Kraft E10wurde berechnet, indem man die Formulierung des Elastizitätsmodultensors, ausgedrückt alsRisstensor zweiter Ordnung theoretisch auf bereits existierende Mikrorisse angewandt hat.Außerdem wurden die neun Module des Oshima-Granits unter der Annahme orthorhombischerElastizität E10mit einem einachsigen Kompressionstest bestimmt. Einundzwanzig Stichproben,die ohne die Annahme irgendeiner Symmetrie genommen wurden, zeigten ebenfallsorthorhombische Merkmale. Die Richtung der Symmetrieachsen stimmte mit der Orientierungbereits vorhandener Risse überein. Der Vergleich der Ergebnisse der auf dem Risstensorbasierenden Formulierung mit der experimentell bestimmten Formulierung zeigt, dass dieAnisotropie der Elastizität von Oshima-Granit von bereits vorhandenen offenen Mikrorissenverursacht wird, und nicht von vorhandenen vernarbten Mikrorissen, und dass dieRisstensorformulierung auch zumindest für eine Annäherung erster Ordnung benutzt werdenkann, um die durch vorhandene offene Mikrorisse induzierte Anisotropie des Oshima-Granits zubeschreiben. RESUME: Les comportements anisotropes du granit d’Oshima ont été étudiés en réalisant destests de compression simple, et en observant les microfissures au microscope optique. Le tenseurdu module d’élasticité du granit d’Oshima sous une résistance de 10 pourcents, E10, a été calculéen se servant de la formule théorique du tenseur de module d’élasticité basé sur le tenseur defissures de second ordre des microfissures ouvertes préexistantes. En outre, sur base del’hypothèse de l’élasticité orthorhombique, les neuf modules du granit d’Oshima ont étédéterminés par des tests de compression simple. Vingt et un modules d’échantillons, calculés endehors de toute hypothèse de symétrie, ont aussi montré des caractéristiques orthorhombiques. Ladirection des axes de symétrie correspondait bien à l’orientation des fissures préexistantes. Lacomparaison des résultats de la formule basée sur le tenseur de fissures avec les résultatsdéterminés expérimentalement montrent que l’anisotropie de l’élasticité du granit d’Oshimaprovient des microfissures ouvertes préexistantes, et non de microfissures préexistantes referméeset que la formule du tenseur de fissures peut servir, au moins comme première approximation, àdécrire l’anisotropie du granit d’Oshima marqué par des microfissures ouvertes préexistantes.

Jan 1, 2003

By J. Little

It is common practice for underground mine plans to be created sequentially, where results from one planning process form the input data for another. While this is practical for manual methods, computerized optimization techniques should consider an integrated approach to creating the global mine plan. This is because optimizing an individual mine planning process, such as stope layouts, introduces a likelihood of increasing costs or decreasing revenues associated with other areas, such as production scheduling, as harmful decisions must be balanced. Considering the interaction and influence that individual underground mine planning processes have on each other during optimization will provide more profitable results than if these are ignored. Optimization techniques for stope layouts and production scheduling are reviewed. An integer programming model is proposed that allows for either integrated or isolated optimization. Both approaches are separately applied to a block model. The results demonstrate the model?s ability to produce optimal long-term sublevel stoping mine plans and the benefits of using an integrated approach. Keywords underground mine optimization, stope layouts, underground production scheduling, integer programming, mathematical programming application.

Oct 1, 2013

By H. Hamma, R. Fehrmann, M. Gaune-Escard, G. Hatem, S. B. Rasmussen, K. M. Eriksen

The molten salts M2S2O7and MHSO4, the binary molten salt systems M2S2O7-MHSO4and the molten salt-gas systems M2S2O7-V2O5and M2S2O7-M2SO4-V2O5(M = Na, K, Rb, Cs) in O2, SO2and Ar atmospheres have been investigated by thermal methods like calorimetry, Differential Enthalpic Analysis (DEA) and Differential Scanning Calorimetry (DSC). Fundamental thermodynamic data like temperatures and molar heats of solid-solid transition and fusion, phase diagrams, heat capacities of solids and liquids, heat of mixing, and heats of complex formation have been obtained and are reviewed here. Also EPR spectroscopic evidence of V(IV) complexes and their structure are reported and the results are discussed in relation to the mechanism of SO2oxidation by V2O5based industrial catalysts. Keywords: Alkali pyrosulfates, alkali hydrogen sulfates, vanadium pentoxide, EPR spectroscopy, complex formation

Jan 1, 2004

By T. Watanabe, S. Hayashi, M. Hayashi, K. Nagata, H. Fukuyama

Chemical states of fluorine in CaO-SiO2-CaF2glasses in a composition range of CaO/SiO2=0.5?1.3 and 5?25 mol%CaF2have been investigated by 19F solid-state NMR with and without MAS. The isotropic chemical shifts of the glasses are close to those of cuspidine crystal (59.4 and64.3 ppm with respect to C6F6) and CaF2crystal (58.6 ppm). The fluoride ions are coordinated with four or less than four calcium ions in this composition range. The chemical shifts move to the lower frequency with an increase in the CaF2content, whereas those are not affected by theCaO/SiO2ratio. The ionic distance between calcium and fluoride ions increases with an increase in the CaF2content. The chemical state of fluorine is not disturbed by the degree of polymerization of the silicate network. Comparing the MAS and static NMR spectra, the second moment attributed to 19F-19F dipole-dipole interaction has been estimated. The values of the glasses range over 3.1?7.3107Hz2andthose are larger than the calculated value of cuspidine crystal. This indicates that fluoride ions form Ca-F clusters in the glasses and that the size of clusters increases with increasing the CaF2content. Keywords: chemical state of fluoride ion, CaO-SiO2-CaF2glass, solid state 19F NMR spectroscopy

Jan 1, 2004

By Y. Nakata, K. Nagata

Plasma is partially ionized gas composed of ions, electrons and activated elements at high temperature. Some flying ash from incinerated municipal waste is melted to become glass by a transfer-type arc plasma furnace. As the glass is ionic silicate, when an electric current passes through anode to cathode, ions in molten slag electrochemically react with electron in plasma at the surface of molten slag. In case of molten Na2O-SiO2, sodium ions in the molten slag carry electric current and SiO2are reduced to evaporate as SiO gas by electron in plasma. The cases of Ag+in NaNO3-KNO3molten salt and Fe2+in FeO-SiO2slag were examined. The amount of cathodic reaction is larger than that of anodic reaction and not apparently according to the Faraday?s law on the electrochemical reactions.

Jan 1, 2004

By L. Holappa

Ferroalloys like FeCr and FeMn are mostly produced in submerged electric arc furnaces. Typical for these processes is that the amount of slag is quite high. The role of slag for the process is thus very essential and specific chemical, physical and electrical properties are required. Slags in FeCr process are Al2O3-MgO-SiO2based with minor contents of CaO and CrOx. Slags in FeMn process are principally similar originating from silicate minerals but can have quite a large composition range depending on the manganese ore and its gangue minerals. Characteristic for FeMn process is that the slag is rich in manganese oxide up to above 30%. A common feature is that the ?ore oxides?, CrOx and MnOxin slag are not only divalent oxides but also containing some higher valent of Cr3+ and Mn3+, respectively. In FeMn production conditions the slag consists mainlyMn2+. This is a clear difference from CrOx containing slags in which both two and three valent coexists in slags in FeCr process conditions. Oxidation state of the slag depends on the ambient oxygen partial pressure and temperature in the examined process. Thermodynamics of slags in ferroalloys production are discussed in terms of phase diagrams, activities and oxidation state of chromium and manganese oxides. Further, slag properties influencing reduction kinetics and furnace operation i.e. viscosity and electrical resistivity are discussed. Keywords: review, slags, ferroalloys, ferrochromium, ferromanganese, thermodynamics, physical properties.

Jan 1, 2004

Ferrochrome is the major chromium source for stainless steel production, and submerged-arc furnaces (SAF) are most commonly utilised to smelt chromite ores into ferrochrome by using suitable carbonaceous reductants such as coke. Because of the complexity of feed structure and electrical-thermal-chemical interactions, there exist large gradients and wide distributions of temperature, mineralogy and other process variables in the furnace. This leads to various zones in the furnace, and different reduction mechanisms. Control of the furnace is thus often difficult due to the complicated physical and chemical situations in the furnace. The temperature profile in the submerged arc furnace has a great influence on the reduction rate and the production efficiency. Therefore, the energy generation through electrical arcs submerged in the solid feed and its distribution within the packed bed play an important role. In the present paper, an overall process model is illustrated to simulate inter-linked transport processes of fluid flow, heat transfer and reduction kinetics within the submerged arc furnace. The application of reaction kinetic data to simulate the chromite pellet/lumpy ore reduction with CO gas is presented and further adjusted to provide a submodel for a flow and heat transfer simulation for the packed bed by using computational fluid dynamics (CFD) technique. The comprehensive process model is aimed to simulate materials and gas flow, temperature and energy distribution throughout the furnace system. A preliminary model for gas flow and temperature distribution for the upper part of a 20 MW furnace (the packed bed) for high carbon ferrochrome production has been developed under simplified conditions. The integration of the reaction kinetic model into process simulation, and the future vision for a more comprehensive process modelling are discussed. It is expected that better understanding of the furnace insights through process modelling will help process optimisation and furnace control.

Jan 1, 2004

By S. E. Olsen, M. Tangstad, G. Tranell, K. Berg, S. Gaal

In this study, the reduction behaviours of MnO and SiO2containing slags by solid carbonaceous materials was investigated in both small and larger-scale laboratory experiments. Five types of carbonaceous material were investigated: 2 graphites, industrial coke, anthracite and eucalyptus charcoal. The effects of the reductant type/properties on the reduction kinetics, metal composition and metal yield, have been quantified. Results show that the reduction rate is highly dependant on the type of carbon used. It was found that the reductant type significantly influenced the SiO2reduction while it did not seem to have a large effect on the MnO reduction. This may be due to the different CO2and SiO reactivities of the materials.

Jan 1, 2004

Published experimental data on thermodynamic behaviour of cobalt-containing slags have been reviewed and used in validating a recently developed thermodynamic model. The results from the exercise show that the model provides a reasonably good description of behaviour of cobalt in multi-component slag systems. The models for cobalt containing slags, matte and oxide solid solution phases were incorporated into CSIRO?s multi-phase equilibrium (MPE) package, which was used to calculate the equilibrium distribution of cobalt between matte and slag phases under various conditions. The results agreed well with the experimental data. Furthermore, the good agreement between the calculation and the plant data indicates that the operating conditions of industrial smelting and converting processes are close to equilibrium. Two diagrams showing the effects of slag chemistry and SO2and O2partial pressures on the distribution of cobalt between phases were generated for conditions similar to smelting and converting processes. These diagrams provide some useful guidelines for developing new strategies to improve cobalt recovery.

Jan 1, 2004

By M. Görnerup, A. Kapilashrami, Seetharaman. S., A. K. Lahiri

Simultaneous reduction and foaming of chromium-rich slag have been studied in a laboratory furnace equipped with X-ray image analysis. Reduction of the metal oxides by graphite generated CO, which caused the melt to foam. The slag composition continuously changed due to reactions and dissolution of lining. Gas generation rate, foam height, and gas bubble size were studied and correlated to slag composition. Viscosity increased significantly during the experiments due to a change in slag composition. Bubble sizes varied little during the progress of reactions but differed considerably for different slags. Bubble sizes were largest for V2O5 containing slag, which is contrary to the general understanding that the presence of strong surface active agents reduces the bubble size. The foaming index did not follow expected trends for bubble size and viscosity, suggesting that foaming index is not a suitable parameter for discussion of foams under dynamic conditions. Keywords: slag, foaming, dynamic conditions

Jan 1, 2004

By J. W. van der Merwe, A. S. Bolokang, M. J. Phasha, V. J. Matjeke, C. Moopanar

"Excessive wear rates on railway wheels can result in rolling-stock derailments. If wear is detected early the possible derailments can be prevented by prematurely replacing wheelsets, although the inventory cost and maintenance downtime remain a challenge. In the current study, wheels were introduced and monitored in-service for two years to investigate the cause of excessive wear rates. The wear rates and stresses were calculated for the wheels suitable for a maximum load of 26 t per axle. Microstructural and mechanical properties were analysed. As expected, the general microstructure of all the wheels tested was pearlitic. Although all the wheels complied with the tensile strength requirements, stress calculations confirmed material distortion on excessively worn wheels whereas trial wheels revealed yield strength exceeding the yield criterion. High wear rates observed on the wheels were a result of low yield strength relative to the load per axle. The typical wear mechanism found was due to a combination of rolling contact fatigue and abrasive brake wear. Despite compliance of the wheels with existing requirements regarding material and mechanical properties (hardness, ultimate tensile strength), it is recommended that the yield strength must also be taken into consideration as a critical parameter.IntroductionRailway wheels are used to support the wagon mass and guide the wagon along the tracks (Park, 1974). The wheels and rails must be able to tolerate the applied tangential forces in order to effect wagon dynamic performance and reduce material deformation (Ghidini et al., 1994; RSE_TE_SPC_0045, 2011; AAR M107/M 208 Specification, 2011. Over the past ten years, the South African coal wagon maintenance depot has experienced excessive hollow wheel wear rates on the heavy haul line wheels. The maximum load of Jumbo wagons on the coal line is 104 t, or 26 t per axle. Although the maintenance intervention cycle for wheelsets was two years, between February 2011 and August 2012 some wheels experienced excessive hollow wear. Hollow wear is regarded as wear exceeding 2 mm on the central portion of the wheel tread (RSE_TE_SPC_0045, 2011). This happened despite the fact that these wheels were manufactured and certified according to the requirements of AAR M107/208 standard for carbon steel wheels (AAR M107/M 208 Specification,. 2011) and the local wheel RS/ME/SP 021 standard specification (RS / ME / SP / 021 REV 5 (2013). The AAR standard only specifies a minimum hardness as a required mechanical property and the local standard specifies hardness and minimum tensile strength only. In general, an increase in hardness will improve the rolling/sliding wear resistance of steel. This relationship of hardness and wear resistance was found to be true only in a situation where solid and similar alloys are in contact (Singh, Khatirkar and Sapate, 2015). The sliding wear resistance of a material is usually estimated using Archard’s equation (Liu and Li, 2001)."

Jan 1, 2016

By A. Hiltunen, R. Hiltunen

The utilization of blast furnace and BOF slags has long traditions and well-known applications in the building and road construction industries and in soil conditioning. The starting point for product development has been the basic physico-chemical properties of slags. This development has led to the almost 100% utilization of blast furnace slags and also considerable amounts of steel slags. While new methods and applications are continuously being looked for and developed in order to recycle and utilize all types of slag, there is at the same time an increasing debate over the exact nature of the slags, whether they are products or waste material, and whether they should be considered substances or preparations. These questions have emerged as a consequence of the environmental effects of the slags and current environmental legislation. The environmental effects of slags can be seen to be both beneficial and less beneficial. There is no doubt about their benefits in the road construction industry, as they allow significant savings in terms of natural materials and in transportation. It is also a known fact that using slags as fertilizers and in the cement industry leads to reduction in CO2emissions. The less favourable effects are the possible harmful emissions into the soil and groundwater. In this paper we describe the properties of slag products and their environmental effects according to investigations carried out in Finland. Keywords: utilization, blast furnace slag, steel slag, properties, solubility, environment

Jan 1, 2004

By S. H. Yi, J. R. Kim, Y. S. Lee

The viscosities of CaO-SiO2-Al2O3-MgO-FeO slags were measured under conditions ofCaO/SiO2=1.15–1.6, 10–13 percent Al2O3, 5–10 percent MgO and 5–20 percent FeO. Slag viscosity decreased with increasing FeO content at a fixed basicity (CaO/SiO2) of slag. Slag viscosity at low FeO (<7.5 percent FeO) exhibited a minimum value by increasing MgO content in slag. Viscosity decreased with increasing slag basicity up to 1.3 while it increased as slag basicity increased from 1.3 to 1.5. Thus, it was proposed that the driving force for the decreases of slag viscosity would be an increase in depolymerization of silicate network at C/S=1.3, while the viscous behaviour at C/S>1.3 would be increased with increasing the chemical potential of primary solid phase e.g. dicalcium silicate. A thermodynamic approach for the activity of primary solid phase in molten slags resulted in a reasonable relationship between viscosity and slag components. Therefore, it was confirmed that slag viscosity in basic slags system (C/S>1.3) could be determined by the chemical potential of dicalcium silicate. Keywords: viscosity, basicity, bosh slag, blast furnace, slag structure, FT-IR

Jan 1, 2004

By A. Normanton, B. Harris, V. Ludlow, S. Riaz

Why does a continuous casting mould powder, which works successfully on a particular caster with respect to semi quality, fail to perform on a caster of a similar design utilizing liquid steel from a similar route for an identical product without some tuning of its make-up and composition? In casting sequences of the same steel grade, why do some apparent random heats produce poor surface quality with respect to cracking when otherwise good surface quality is realized? The answer to these questions lies in the interaction of the mould powder, the casting hardware, and the casting process variables. Using, as examples, data collected from within Corus UK and during collaborative work on the assessment of mould powder performance and its effects on surface quality, the interaction of the mould powder, the casting hardware and the casting process variables is explored. The steelmaking route and its associated alumina load, unexpected changes to slag chemistry, infiltration of the slag into the mould strand gap, and the nature of the slag film are all shown to affect powder performance. Keywords: continuous casting, mould powders, alumina, slag films

Jan 1, 2004

By M. Magnelöv, Du Sichen, U. Sjöström

An experimental study has been performed to investigate the behaviour and separation of inclusions at the interface between steel and slag. The study has been limited to liquid inclusions because they can be a potential problem in transient situations such as ladle changes in continuous casting of steel. Model experiments with water and silicon oils have been carried out to study the kinetics of separation of simulated inclusions at an interface. The properties of the inclusions and the slags have been varied by using different oils with different viscosities, densities and surface tensions. The effect of temperature of the liquids has also been examined. Measurements of the terminal velocity, rest time and the behaviour of the liquid inclusions at the interface have been recorded using a video camera. It has been found that the inclusions reach their terminal velocity early in the vessel and the experimental velocities differ somewhat from the values evaluated using ?intermediate law?. The results from the experiments have shown that the size of the inclusions has no appreciable influence on the rest time. Droplets of AK50 oil have been found to have considerably long rest time. A water film surrounding the droplet has been expected to be the main reason for the long rest time. The present study has also shown that the viscosity of the oil has certain effect on the rest time, but only to some extent, since viscosity has double functions. A higher viscosity provides higher resistance to the droplet entering the oil phase leading to longer rest time and at the same time damps the lateral movement of the droplet along the interface, leading to easier stabilization and shorter rest time. On the other hand, a high viscosity of the oil phase results in slow dissolution process. It has been concluded that a meaningful model of inclusion separation at the metal-slag interface must take the interfacial phenomena into consideration. Keywords: Inclusions, terminal velocity, rest time, dissolution.

Jan 1, 2004

By J. Böhlke, B. Friedrich, E. Hecker

The legislation for the disposal of heavy metals contaminated substances is still going to be tightened up in the future. The main criteria for the utilization or deposition of these residues are the content and the water solubility of these metals. Through this, the use of slags from the lead-and zinc-industry in road building may become limited or even not possible at all. From an economic point of view this would lead to Pb/Zn losses and costs for safe dumping. This paper investigates the feeding of the reducing agent via hollow electrode DC smelting and the yield of metal reduction. After carrying out thermodynamic calculations, the process window conditions for electric-arc furnace tests were determined. Doing this, the zinc could be reduced, evaporated and recovered as an oxidic intermediate product flue dust, while the lead was present either in flue dust or in metallic form. The zinc content in the final slag could be reduced by up to 90%. The slag product has undergone an eluation test which allows it to be used as building materials. Keywords: zinc reduction, lead reduction, hollow electrode, slag treatment, electric arc furnace