Search Documents

By F. S. Hoseinian, B. Rezai, E. Kowsari, M. Safari

In order to remove heavy metal ions from a large volume of wastewater with a low ion concentration, ion flotation appears to be promisingly effective. In the ion flotation process, because of the high ion removal percentage, the amount of water recovery percentage is a very important factor which determines the process efficiency. However, ion flotation suffers from relatively high collector concentration to achieve the high removal percentage to the desired limit, which subsequently increases the water recovery. In this study, functionalised graphene oxide (FGO) was synthesised, using a chemical method in the ion flotation process, applied as a collector for increasing process efficiency by reducing the collector consumption and water recovery. The high ion removal was achieved with both collectors of sodium dodecyl sulfate (SDS) and FGO, while the water recovery with a collector of SDS was 3.4% higher than that with a collector of FGO. The results indicated that the FGO could be effectively used for high ion removal and low water recovery in the ion flotation process. Keywords: Ion flotation, synthesised collector, ion removal, wastewater, water recovery

Jan 1, 2020

By R. C. Nkhoma, K. A. Annan, S. Ngomane

The effects of welding current, electrode force, and welding time in a resistance spot weld were studied to investigate the effectiveness of welded joints between a thin EN10130: DC04 material and a thicker 817M40 part, through analysis of the microstructural and mechanical properties. All welded specimens were subjected to tensile testing at room temperature (25°C) and sub-zero temperature (–46°C) to test the strength of the welded joints. No full button failure was observed at either room temperature or sub-zero temperature after optimization of the weldng parameters. The fusion zone was observed to consist mainly of martensitic phase, due to rapid quenching, while the HAZ was composed of clusters of martensite in a ferrite and bainite matrix. The base 817M40 metal remained fully ferritic after welding. The hardness was found to increase with increasing welding current. An increase in nugget size, indicating good fusion of the weld, was observed with an increase in the welding current.

Oct 1, 2021

By A. C. Lawrence, K. F. Mauer

Human factors in stope productivity -a field experiment by K. F. MAUER, M.A. (Visitor), and A. C. LAWRENCE, B.Econ., D.Com. (Member) An experiment in which three human variables were manipulated in eight stopes was conducted in a gold mine over a period of roughly six months. The three variables, which each had two levels, concerned the degree of movement from gangs, the quality of the Bantu production supervisors, and the extent to which gangs were composed of a single ethnic group (Malawians). Time was included as a variable with three levels in the analysis of the findings. On the average, stable gangs produced 12 per cent more than gangs with a high percentage of transfers, gangs with better production supervisors were more successful by nearly 9 per cent than those with poorer production supervisors, and homogeneous gangs were more productive than heterogeneous ones by as much as 15 per cent. In addition, it was found that a number of the variables exercised a joint influence on stope productivity and that the effects of the variables were accentuated by the len gth of time they had been in operation. V

Jan 10, 1973

By L. Chanderman, C. E. Dohm

"Mineral Resource estimation (MRE) and classification are highly dependent on the confidence in the model of the orebody geometry, known as the geological model, within which the estimates are constrained. An understanding of the geology of a deposit is thus fundamental to the Mineral Resource evaluation process. The geological model is a function of the structural and depositional complexity of the geology captured by drilling information, which is limited in the early stages of a project. The information effect has a significant impact in terms of the interpretation of the geology as well as the estimation of grade continuity and the resultant risk associated with the Mineral Resource estimate and classification.Therefore, as new drilling information becomes available, it is necessary to update and refine the geological model to appropriately constrain the resource estimates. The grade information is also updated, including statistics and the spatial correlation characteristics. This refinement is based on geological interpretations derived from the drillhole information that becomes available throughout the life of the mine; orebody knowledge that comes from working experience of the deposit, as well as familiarity with the software package used for modelling, is also important.In updating, the potential to identify new resources in previously unknown areas may be realized. The opposite may also occur where previous interpretations of ore continuity are refuted. Both scenarios could result from a better understanding of the geology of the deposit and thus a more realistic MRE, which reduces geological risk. This paper describes how newly drilled advanced grade-control holes for a gold deposit in Mali were used to refine the 3D geological model for the deposit in an attempt to identify the potential for additional oxide ore using conventional geostatistical evaluation techniques."

Jan 1, 2017

By Pentti Niskanen

"The ventilation system of the Pyhasalmi Mine is described. The mine is located in an area where the annual atmospheric temperature may vary from +30°C to -30°C. Natural ventilation causes serious difficulties because the underground mine is connected by drifts and finger raises to the bottom of the 120 m-deep open pit.The natural ventilation tends to make the ventilation net unstable. The paper describes how the instability characteristics of the ventilation net can be studied and how they have been taken into account when automating the control of the ventilation. In addition, the software, hardware and costs of the system are described. The system consists of 12 automated ventilation doors, two mine fans, 8 elements for sensing the air flow and temperatures, a control panel and a process computer."

Jan 1, 2014

By M. R. L. Blackwell

Over the period 1964 to 1969 Conzinc Riotinto of Australia undertook and completed an evaluation of a large low-grade copper orebody on Bougainville Island in the Territory of Papua and New Guinea. From the outset it was clear that the geographic, climatic and topographic characteristics of the area would necessitate a heavy capital outlay on production and support facilities. Both the physical problems and the magnitude of the investment amplified the need for a thorough and rigorous evaluation of the various strategies for exploiting the orebody. In view of the number of independent and inter-related variables and the flow of new data, a computer-based evaluation process extended the scope and depth of the analysis considerably. The system used permitted an iterative assessment and re-assessment of the various strategies with the results becoming increasingly refined with time. This process encompassed the modelling of the orebody, the simulation of alternative operating strategies and the determination of the financial profitability of the project,

Jan 1, 2014

By J. D. T. Steyl, G. B. Grobbelaar

Two examples are presented to show how first-principles – physical-dynamic, here termed behavioural modelling, is used to build digital twins of unit processes or plant sections. A digital twin equips the metallurgist, engineer, or manager with a powerful tool to conduct model-based design, solve process problems and improve operations. It is particularly relevant in the metallurgical industry where plant behaviour is highly integrated, rates respond to particle dynamics in complicated ways and mineral flows across flowsheet boundaries are variable. The two examples used to illustrate the behavioural modelling methodology are 1) a flotation column unit block and 2) a multi-compartment pressure oxidation (POX) autoclave. It simultaneously accounts for the causality of material and heat flow, takes care of mineral particle dynamics, physical and chemical reaction rates, the plant control system behaviour and operating heuristics. The basic modelling building blocks are briefly reviewed to show how the behavioural modelling attributes constrain the mass and heat flow dynamics to physically realistic values. This is the key aspect that allows project value to be created with minimal input data. Behavioural modelling is especially valuable where the process dynamics are poorly understood or controlled, where data-driven models fail to cope with complex and highly integrated plant behaviour, where quality data is lacking or limited funds are available to generate the data required to fill all the knowledge gaps. The paper uses the flotation column example to show how behavioural modelling and simulation can be used to optimise plant performance, while the multi-compartment POX autoclave model shows how it can be used to diagnose process problems. It also provides a solid basis to add a data-driven component – in other words, it makes a strong case for a hybrid first-principle– data-driven approach to solve process problems, especially where microscopic-level understanding is poor. Keywords: Digital twin, behavioural modelling, simulation, flotation column, pressure oxidation

Jan 1, 2020

By K. M. Banks

The hot ductility of in situ melted tensile specimens of micro-alloyed steels having C contents in the range 0.12?0.17% (mass %) have been examined over the 700?1000°C temperature range. An improved testing method for simulating the continuous casting process was used, which takes into account both primary and secondary cooling conditions. Increasing the N content to electric arc furnace levels (0.01% N) was found to cause a serious deterioration in ductility. V-N steel gave better ductility than Nb-containing steels due to less precipitation. From a cracking perspective, low- N steels are generally recommended but, when not feasible, a combination of Nb and V gives even better ductility. However, to be sure of avoiding transverse cracking in higher N steels a small addition of Ti is required. This resulted in a decrease in the fraction of fine particles and in accord with this better ductility. Transverse cracking of industrial slabs was then avoided.

Jan 1, 2011

By T. Wajima

Recovery of precious metals from hydrochloric solution using sulfur-impregnated carbonaceous adsorbent was examined. Sulfur-impregnated adsorbent with adsorption abilities of precious metals can be prepared from activated carbon using pyrolysis at 600 oC under 10 % H2S gas flow, and the adsorbed Au and Pd were precipitated as metal phase on the surface of the adsorbent. The adsorbents after precious metals adsorption were burned at 700 oC to obtain the residue mainly containing precious metals. The adsorbent was found to be highly efficient and selective for the uptake of precious metals, especially Au, in the presence of excess base metal ions from simulated spent automotive catalyst eluted solution using a column pack test. Keywords: Gold, platinum, palladium, reduction precipitation

Jan 1, 2020

By S. Mohanta, B. C. Melkap

"SynopsisDry beneficiation of coal by air dense medium fluidized bed is an emerging trend. It is widely believed that the particle size of the medium has a significant effect on the separation efficiency. This investigation demonstrates that medium particle size has a major effect on separation efficiency. Experimental results show that different size fractions of the same feed respond differently to the same size fraction of medium solids. Furthermore, a particular size fraction of feed coal responds differently with different size fractions of medium solids. The Ep values and overall metallurgical performance parameters, obtained from experimental results, clearly indicate the superior performance of an air dense medium fluidized bed separator when using –150+106 µm magnetite powder as the fluidizing medium. These observations reinforce the importance of sizing the medium particle size for the air dense medium fluidized bed.IntroductionIn an air dense medium fluidized bed (ADMFB), a fluidizing bed of a particular density is created by suspending solid particles in an upward air flow. A feed containing coal particles of different densities is introduced into this fluidizing bed. The particles with relative density less than the bed density float on the top of the bed, while particles denser than the bed density sink through it. Since there is a general correlation between ash content and density of coal particles, it is possible to remove ash-forming impurities from a raw coal to the required level by regulating the density of the fluidizing bed. Recently, the ADMFB process has received significant attention world-wide for its specific advantages of low operating cost and less restrictive for small capacities (Luo and Chen, 2001; Houwelingen and de Jong, 2004; Dwari and Hanumantha Rao, 2007; Sahu et al., 2009; Mohanta et al., 2012). This process is not recognized as a well-established industrial practice because of the availability of efficient wet processing technology. However, with the revival of interest in dry beneficiation of coal in general, and ADMFB in particular, there is a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have made the process a competitive and viable option for beneficiating coal."

Jan 1, 2015

Dr J. P. Hugo, Pr. Eng., after obtaining a B.Sc. (Eng.) in Metallurgical Engineering at the University of the Witwatersrand in 1948, gained about 9 months' practical experience in a British steelworks, followed by post-graduate studies at Sheffield University, leading to a Ph.D. (Metallurgy) in 1953. Mr G. Y. Nisbet, Pr. Eng., holds a B.sc. (Min.) from the University of the Witwatersrand (1948) and a P.M.D. from Harvard University, U.S.A. (1966). On graduating, he was awarded the Chamber of Mines' Gold Medal. Professor D. G. Krige, holds a D.Sc. (Eng.) from the University of the Witwatersrand (1963) and a D.Ing. (H.C.) from the University of Pretoria (1981). Dr P. T. Wedepohl holds a B.Sc. (Hons.) from the University of the Witwatersrand (1953) and a Ph.D. from the University of Reading, England (1958).

Jan 1, 1984

By G. W. Healy

The smelting of calcium carbide has always been plagued by eruptions, too often with serious injury y or loss of life. To find their causes, the author calculated an internal energy balance using 1992 data for CaC2 and CaO, and older data for the remaining items. The heat content of the charge, and that of the hot gases formed at the reduction temperature, showed that only a fraction of its heat content can be supplied by these gases. Laboratory data on the electrical resistivity of fine mixtures of coke and non-conductive solids were extrapolated to a commercial carbide charge, and then used to calculate the heat produced by current flowing through the mix from the electrode surface to the hearth, which, under favourable conditions, sufficed to bring the charge to 1900 K and higher, at which temperatures reduction could take place.

Jan 1, 1995

The Annual General Meeting of The South African Institute of Mining and Metallurgy was held in Kelvin House on Wednesday, 18th August, 1982. Mr G. Y. Nisbet (President) was in the chair and declared the meeting open at 16h05. Obituaries President: It is my sad duty to announce the deaths of the following members of the Institute: Honorary Life Fellow J. A. Taylor ; Life Fellows J. Watt and J. J. Cairns ; Fellows J. H. Mortimer, R. R. M. Cousens, H. Clark, S. W. Hill, Dr A. Whillier, and Dr C. M. van H. van Staden; Members F. W. McElroy, V. J. Irsigler, B. J. R. Botha, and E. J. Jackson; and Associate B. V. Robertson. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, please rise and ob¬serve a few minutes of silence.

Jan 1, 1982

By T. M. Louw, L. Auret, S. M. Bradshaw, F. F. Noelle

Modern industrial processes undergo frequent process state shifts due to changes in demand, feedstock or maintenance operations. Multimodal continuous process monitoring is therefore required for effective plant operation. Steady state analysis is a key component in effective multimodal monitoring. Various issues still remain in determining the starting and ending times of transition states. High dimensionality of process data is a characteristic that makes it difficult to select variables to consider when conducting steady state analysis. In order to address these problems, steady state detection on the principal component space is proposed. First, data undergoes principle component analysis to reduce dimensionality, then existing multivariate steady state detection algorithms are applied on the principle component scores. A novel algorithm, threshold PCA-SSD, is proposed and compared to an existing technique for steady state detection. The algorithms are investigated on high dimensional synthetic data Keywords: Multimode process, steady state detection, principle component analysis

Jan 1, 2020

By G. E. Blight

Several aspects of the behaviour and properties of backfills consisting of cemented cyclone underflow tailings are illustrated by means of examples, and guidelines are given on the optimization of the performance of cemented fills. The stretch characteristics of the geofabric used to contain freshly placed backfill are described, as well as the relationship between these characteristics and the forces acting on retaining barricades. The properties required to achieve a self-supporting, stable free face in cemented backfill are explored, and a graphic relationship between stable height and shear strength is presented and compared with that for uncemented (classified) tailings. After a description of the characteristics of Witwatersrand quartzite gold-tailings backfill and commonly used cements, the process of drainage and air entry into backfill is outlined. Following this, the early-age gain in strength and the shear-strength characteristics, as well as the compressibility characteristics of cemented backfill, are described. Two phenomena that are potentially damaging to cemented backfill are seismic effects (or blasting acceleration) and the closure that takes place during the curing of cement. Investigations show that neither of these phenomena is actually significantly deleterious to gold-tailings backfill: liquefaction does not Occur as a result of seismicity, and hydration of cemented fill is not significantly impeded by closure.

Jan 1, 1996

It is well known that the ability to influence project value reduces significantly as planning progresses and decisions regarding project parameters are made. However, at the prefeasibility stage in particular, where one of the main aims should be to evaluate a wide range of options in order to select the best for more detailed further study, there is often a reluctance to spend the time and money needed to do this rigorously. This paper demonstrates, by a number of case study examples, how significant increases in value may be obtained by fully evaluating the combinations of alternatives for various project design parameters, including (though not limited to) mining methods, haulage methods, mining rates, processing methods and rates, sequencing of mining, and cut-off grades, with changes and upgrades over time where applicable. The additional value unlocked is typically orders of magnitude greater than the additional cost of the more comprehensive study. The dangers of misuse of simplistic sensitivity analyses and failure to identify how strategies might change in response to changes in external factors are also illustrated, and the importance of selecting the best `grade descriptor' is discussed.

Jan 1, 2007

By Jürgen Antrekowitsch, Harald Osthof, Stefan Steinlechner

"In the case of feasibility assessments or feasibility studies, an important point of discussion is often how to calculate the capital (CAPEX) and operating expenditure (OPEX) of a plant. Generally, there is also the request to know how the CAPEX varies when the size of the plant is increased. Nowadays, many databases give an indication of specific equipment costs in relation to the production rate. These data are based on cost information from equipment suppliers and have to be continuously updated by the owner of the database. The approach presented here is a model which allows sizing of process equipment, for example a leach tank, based on process data in combination with the calculation of mechanical properties. Furthermore, it calculates the CAPEX based on construction material cost and adequate machining surcharges. Thus, a single cost model for a leach tank is adequate for both copper and other hydrometallurgical plants and stays valid with changing construction material prices. To summarize, the advantage of this model is the more versatile approach and thus the flexibility due to the inclusion of design aspects, process and mechanical engineering aspects and an updatable database. The database, which is in regard to material cost and is the basis for the cost estimation, is easily updatable from commonly accessible data. This model thus approaches the procedures of an engineering company when designing a plant and executing a cost calculation. INTRODUCTION Hydrometallurgy nowadays plays an important role in processing of primary and secondary resources. In copper metallurgy, hydrometallurgy accounts for roughly 20 % of worldwide primary production, especially in the case of oxide or low copper-containing ores. Zinc smelters changed their method of production from a pyrometallurgical-dominated concept decades ago to mainly hydrometallurgical routes today. Gold production processes using leaching, especially, have a long history without any development which would not be competitive if not based on hydrometallurgical concepts (Pawlek, 1983; Winnacker-Küchler, 2006)."

Jan 1, 2015

By M. Seerane, R. Machaka, P. Ndlangamandla

"Metal injection moulding (MIM) is a near-net-shaping powder metallurgy technique suitable for the cost-effective mass production of small and complex components. In this paper, the effects of the metal powder particle size on the final properties of 17-4 PH stainless steel are reported. Three different particle sizes (d50 33.0, 7.91 and 4.04 µm) were used to prepare the injectable MIM feedstocks using a CSIR-developed wax-based binder system at a fixed solids loading of 60 vol.%. The distribution slope parameter and the rheological flow index behaviour were used to predict the flowability of the feedstocks. The effects of the particle size on MIM products were established. The results are discussed in terms of the subsequent microstructural and mechanical properties of MIM 17-4 PH stainless steel against the established MPIF Standard 35. IntroductionMetal injection moulding (MIM) is a near-netshape manufacturing process established as an alternative to produce complex small-tomedium shaped components that were previously fabricated by conventional methods at higher costs (Attia and Alcock, 2011; Todd and Sidambe, 2013).Although recent advances in micromanufacturing (mainly machining and electrodeposition-based) have enabled the fabrication of complex micro-size geometries directly into miniaturized parts, these processes are generally neither routine nor easily accessible at present (Attia and Alcock, 2011).Typically, the MIM process consists of four steps: mixing, injection moulding, debinding and sintering. Mixing involves blending of the desired metal powder composition with carefully selected multicomponent organic binders at the right proportion. This mixture, which is called feedstock, is then injected into a mould of a required shape to form a ‘green part’. Debinding is the removal of the binders by chemical, thermal, or catalytic means while maintaining the shape of the part. Finally, the debound part is sintered to a full or near-full density part (Sotomayor, Varez and Levenfeld, 2010). The MIM process is essentially a combination of plastic injection moulding with conventional powder metallurgy technologies."

Jan 1, 2016

By J. D. Zhou, F. Yang, X. G. Bi

"In this investigation, the phosphorus distribution ratios in the CaF2 system and B2O3 system dephosphorization slags for high-phosphorus hot metal pretreatment were measured by an indirect method under laboratory conditions. Firstly, the phosphorus distribution ratio between liquid slag and solid iron was measured, and then the phosphorus distribution ratio between liquid slag and hot metal was calculated. Phosphorus capacity was calculated in terms of the composition and optical basicity of the slag. Dephosphorization slag was also studied by scanning electron microscopy, energy dispersive analysis, and X-ray diffraction analysis. The experimental results show that the phosphorus capacity of the B2O3 slag system is much greater than that of the CaF2 system. It is demonstrated thatB2O3 can completely replace CaF2 as fluxing agent for high-phosphorus hot metal pretreatment. With CaF2 as fluxing agent, the phosphorus capacity increases with increasing CaO content in the slag, but the phosphorus distribution ratio decreases. B2O3, when used as fluxing agent, can react with high melting point phases such as 2CaO·SiO2 and 3CaO·P2O5 in the slag to form new phases with low melting points such as 11CaO·B2O3.4SiO2, 2CaO·B2O3.SiO2, and Ca9.93(P5.84B0.16O24) (B0.67O1.79), thereby acting as a fluxing agent. When the ratio of w(B2O3)/w(CaO) is 0.16, the phosphorus distribution ratio reaches its maximum value, that is, the dephosphorization ability of the slag is at its maximum. IntroductionAs international iron ore prices continue to rise, the development of China's steel industry is facing a lot of pressure. Against this background, development and utilization of domestic high-phosphorus iron ore resources is particularly important. When highphosphorus iron ore is used in ironmaking, the phosphorus content in the hot metal can reach 0.35% or more, and the hot metal must be pretreated. For hot metal with 0.08–0.10% dissolved phosphorus, the traditional hot metal dephosphorization pretreatment technologies are relatively mature. However, when using these methods to dephosphorize hot metal containing 0.35% P or more, the amount of dephosphorization slag can reach 100–150 kg per ton of hot metal. Furthermore, the traditional dephosphorization methods require the addition of large amounts of CaF2 as fluxing agent, and this results in high fluoride levels in the dephosphorization slag. The fluorine in the slag can partially dissolve in water and thereby causes high fluoride concentration in the water and soil. Once the fluoride is absorbed by humans or animals, it can result in toxic effects on the central nervous system and myocardium. In addition, fluoride can accumulate in the environment, and thereby pose a health risk to animals and humans through the food chain (Li, 2007; Liu, Wang, and Dong, 2011, Diao, 2013). The objective of this research is to replace CaF2 with B2O3 as fluxing agent while achieving the expected goals of hot metal pretreatment."

Jan 1, 2016

By Z. L. Xue, J. L. Li, X. Y. Wang

"In low-carbon energy-efficient basic oxygen furnace (BOF) steelmaking processes, limestone partly or completely replaces the active lime. The effects of limestone calcination temperature (1200–1500°C) and time (5–15 minutes) on lime reactivity and CaO grain size were investigated. The reactivity was evaluated by titration with hydrochloric acid, and the CaO grain size was analysed using scanning electron microscopy. The results revealed that for calcination temperatures higher than 1300°C, the reactivity reached a maximum and then decreased . The higher the temperature, the earlier the peak of reactivity appears. The CaO grains grow with increasing temperature and time, which leads to the decrease of reactivity. Notably, the effects of temperature on CaO grain size and reactivity are more marked than that of time. To obtain active lime calcined at ultra-high temperature by flash heating, the calcination conditions should be 1300–1400°C for 10–15 minutes, or 1400–1500°C for 8–10 minutes. IntroductionLime is one of the most important slag-making materials for dephosphorization and desulphurization in the basic oxygen furnace (BOF) steelmaking process. The reactivity of lime is a measure of its capability to take part in slag-making. Lime having a reactivity of more than 300.0 mL (4 N HCl), determined by hydrochloric acid titration is generally referred to as active lime (Rusjan et al., 2007; Zeman, 2008). At present, the active lime used for BOF processes comes primarily from a kiln or shaft kiln, where limestone is preheated at 700– 900°C, and then calcined at 1050–1200°C (Drenhaus et al., 2010; Oates, 2007)."

Jan 1, 2016