Search Documents

By C. W. Davis

"A copper-palladium-gold-silver ore is being mined at Salt Chuck, Prince of Wales Island, Alaska, from which a concentrate is produced that contains 40 to 50 per cent copper, and considerable amounts of palladium, gold and silver. There has been much difficulty in obtaining assays for palladium, gold and silver from the mine, smelter, sampler, and umpire that check within reasonable limits. While the results for copper content have not been unusual, the results for palladium have varied as much as 0c8 oz. on 3 oz. material, results for gold differed by 0.1 oz. on 1.6 oz. materials, and for a silver content of 7 oz., results differed by as much as 4.0 oz.The Bureau of Mines was requested to determine the causes of variation in the results of the different assayers, and to develop a satisfactory procedure for analyzing such ore.Three samples of concentrate were received for analysis, two small lots that had previously been assayed by the various laboratories, and one large sample. The large sample was dried and ground in a ball mill, put through a 150-mesh screen, and then returned to the ball mill for thorough mixing. The small samples were ground to pass a 150-mesh screen and then mixed on a mixing wheel.The large sample (No. 1) was analyzed by five different procedures, one of the small samples (No.2) by three procedures, and the other (No. 3) by two procedures (the two small samples being too small for further tests). The different procedures tried and the results obtained arc presented below. The samples of concentrate were from ore mimed and milled by the Alaska palladium Co. at Salt Chuck."

Feb 1, 1926

Reduce the noise levels to which operators of double-drum longwall shearers are exposed without compromising the operational effectiveness of the shearer. The Problem Noise produced by double-drum longwall shearers can be harmful to machine operators. Typical noise levels at the lead-drum operator position range from 100 to 105 dBA, and Federal noise regulations allow only one to two hours of exposure per shift at these levels. Noise radiated by the shearer cutting drum is the primary contributor to the overall noise level. However, test of a noise-controlled cutting drum developed by the Bureau of Mines reduced the operator noise level to 95 dBA, thereby increasing the allowable operating time to four hours per shift. Approach The key design aspect of the noise-controlled shearer drum is its reduced vibration-al response to coal-cutting forces. Laboratory studies have shown that these forces are concentrated in the low-frequency region (500 Hz and below). Since the cylindrical core and the cantilevered I plate-like helix of the standard shearer drum are easily excited by these forces (natural vibration frequencies be-

Jan 1, 1985

By E. K. Kleespies

The Bureau of Mines determined the kinetics of the reaction of titanium-iron alloys with titanium trichloride dissolved in sodium chloride to provide a basis for understanding the reactions occurring in metallurgical processes involving reduction of the metal halides or alloy refining in fused salts. The rate of the heterogeneous reaction was determined between titanium-iron alloys and titanium trichloride to elucidate the effects of alloy composition on the rate. Measurements were made in an inert atmosphere with a high-temperature thermobalance using high-purity reactants. The rates of the reactions were about 1 x 10-5 g Ti/cm2-sec, and the reaction was phase-boundary controlled. Titanium alloys of the body-centered cubic beta structure reacted faster than those with the hexagonal close-packed alpha structure. The inter-metallic compound, TiFe, reacted very slowly, whereas TiFe2 was inert. Alloys containing above 89 atomic percent iron gained weight by reacting with titanium species in the salt solution and depositing titanium in the alloy. The effect of TiCl3 concentration on the reaction rate was determined from 2 to 12 weight-percent TiC13 and at various alloy compositions. At high iron contents, above 50 atomic percent, the TiC13 concentration effect was small. At lower iron contents, the TiC13 concentration effect was greater for beta-crystalline alloys than for alpha-crystalline alloys. The temperature dependence of the reaction between titanium alloy containing 8.7 atomic percent iron and titanium trichloride was measured over the temperature range 1,062° to 1,220° K, and the energy of activation was 7.7 kilocalories for the reaction.

Jan 1, 1967

Improve underground long-hole drilling efficiency and safety by developing a lightweight, easily transportable drilling pust that can be adjusted to fit a range of mine opening heights. Background Standard one-piece commercially available steel posts weigh approximately 10 pounds per foot. Transporting these posts underground and carrying them over obstacles and through small mine doors is very difficult. Because the length of a one-piece post cannot be adjusted, variations in mine opening height at the drilling site must be accommodated. This is accomplished by stacking several wooden blocks to form a base for the post, resulting in a dangerously unstable drilling setup. The only alternative to this unstable setup is to obtain a longer post. There problems can be reduced by the use of a two-piece telescoping aluminum post having a 3-foot adjustment range in 6-inch increments. The two-piece extendable post will be easy to transport and carry underground. It will fit any opening height within its adjustment range. One large wooden block is used as a base and one cap block is used at the top to bear against the mine roof. This arrangement results in a stable, rigid setup.

Jan 1, 1990

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX A - PNEUMATIC TRANSPORT OF FLY ASH 1. Introduction Two types of pneumatic transport of fly ash are critical to the success of (1) Transport of fly ash from the fly ash truck to the entrance to the borehole. Depending on the surface topography, this may be horizontal, decential and ascential. (2) Vertical downflow of fly ash through the borehole. All fly ash trucks have limited pressure with which they can pump the fly ash. Thus, the pressure drop in the fly ash hose will define the maximum length for pumping and consequently the maximum distance that the fly ash truck can be parked from the auxiliary blower. The same relationships describe the flow of the dilute fly ash-air mixture produced by mixing with the auxiliary air from the blower and thus define the selection of the pipe diameter. These are im¬portant considerations in the proper selection of the location of the passages to be sealed and the type of surface preparation required. The flow characteristics of fly ash down the borehole determine the selection of the minimum borehole diameter and the blower pressure. This appendix presents theoretical analyses of these flow regimes and summarizes the limited experimental data obtained during the field tests at Grant Town, described in Section 8.4. The analysis for the borehole flow is presented first as it is of greater interest to the program. This is followed by a discussion of the horizontal flow.

Jan 1, 1973

By Seth C. Schaefer

The Bureau of Mines studied the standard free energies2 of formation of ferrous fluoride (FeF2) and ferric fluoride (FeF3) with high-temperature galvanic cells employing calcium fluoride doped with 1 mole-pet yttrium fluoride as the electrolyte. A free-energy change for the cell reaction Fe (s) + NiF2 (S) = FeF2 (S) + Ni (s) together with the standard free energy of formation of nickel fluoride yields a standard free energy of formation of ferrous fluoride from the elements of ?GF° = -168.74 + 30.63 x 10-3T ± 0.41 kcal/mole (897-1,098 K). (2) Combining the standard free energies of formation of magnesium fluoride, ferric oxide, and magnesium oxide with the free-energy change for the overall cell reaction 3MgO(s) + 2FeF3 (s) = 3MgF2 (S) + Fe2 03 (S) (3) gives a standard free energy of formation of ferric fluoride from the elements as ?Gf° = -281.45 + 90.46 X 10-3T ± 0,67 kcal/mole (880-935 K). (4) Free energies and equilibrium fluorine pressures for the two univariant equilibria of the Fe-F system are tabulated and illustrated.

Jan 1, 1975

By M. E. Tyrrell

The purpose of the work leading to this report was two-fold: (1) To determine the properties of cemented tungsten carbide modified by the addition of one, two, and five percent of titanium diboride, and (2) to compare the properties of these mixtures when sintered, hot-pressed, and flash-welded (resistance-sintered). Minor additions of titanium diboride to mixtures of 94 percent WC and 6 percent Co decrease mechanical strength but increase oxidation resistance in proportion to the amount of the addition. One percent of titanium diboride increased the hardness by 2 Rockwell A units. Hot-pressing produced compacts with the highest density and the best mechanical strength, but losses of cobalt were high and grain growth was pronounced.

Jan 1, 1962

By C. J. Chindgren

The Bureau of Mines investigated the technical problems involved in recovering commercial-grade vanadium products from alkaline solutions of low vanadium content. Conditions were defined for precipitating calcium vanadates from sodium vanadate solutions with calcium chloride and calcium hydroxide and for dissolving the precipitates with acid, sodium carbonate, and sodium bicarbonate to obtain vanadium-enriched solutions from which either red cake or ammonium metavanadate was recovered. Calcium vanadates with CaO:V205 mole ratios of 2, 3, and 4 were produced with recoveries of 93 to 100 percent. Optimum recovery of the low-lime variety of calcium vanadate was obtained by employing excess calcium chloride and adjusting the pH to a range of 8.0 to 8.5. High vanadium extractions were obtained in concentrated solutions by dissolving the calcium vanadate precipitates with any of the reagents tested. The resulting extracts contained 25 to 125 grams V205 per liter. Conventional procedures used to precipitate either red cake or ammonium metavanadate from the enriched solutions gave excellent vanadium recoveries.

Jan 1, 1967

By John Owens, Marc Endicott, Hamid Maleki

This study presents a historic overview of the role of mobile roof support (MRS) technologies in improving stability and worker safety and presents the results of recent field evaluations of the MRS load rate monitoring device and other remote deformation-monitoring techniques. Field studies were implemented at two sites in cooperation among researchers from the National Institute for Occupational Safety and Health (NIOSH), Maleki Technologies, Inc., and J. H. Fletcher & Co. The objective of the field programs were to (1) study the interaction between MRS’s and coal mine strata and (2) develop and test suitable monitoring systems for assessing roof and pillar stability. An MRS consists of a roof canopy, four hydraulic cylinders, a caving shield canopy, and associated electromechanical systems mounted on crawler tracks. The machines are controlled by radio from a remote location and operate on self-contained power units. Typically, MRS’s have capacities of 5,340 and 7,120 kN (600 and800 tons). In comparison to posts, an MRS is capable of maintaining the yield load after significant amounts of roof-floor deformation. Because the mining cycle is accelerated, MRS’s help reduce the potential for time-dependent roof falls. MRS performance has been monitored in the laboratory under controlled static loading conditions and in the field under deep, two-seam mining conditions. Laboratory studies have quantified support capacity and system stiffness as a function of machine height. Field investigations have focused on determination of optimum operating conditions and development of warning systems that indicate excessive load on the machine and/or impending roof-pillar stability problems. Analyses of field data show that roof instabilities are influenced by (1) pillar failure, (2) pillar yielding, (3) mine seismicity, (4)geologic structures, and (5) panel layout designs and mining practice.Pillar yielding and failure (unloading) and seismicity can be conveniently monitored by the load rate monitoring device, but for consistent detection of roof falls, additional deformation measurements directly within the cuts are needed.

By David C. Oyler, Winton J. Gale, Jinsheng Chen, Christopher Mark

A collaborative project between RAG Emerald Mine, NIOSH, and SCT Operations was conducted to investigate ground behaviour, reinforcement performance, and stress redistribution in a coal mine entry subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8 m (16 ft) above the entry. This paper focuses on the computer simulation that was undertaken to provide more insight into the roof behaviour and rock bolt interaction during mining. The model’s input rock properties were derived from extensive laboratory testing, and the model itself simulated a broad range of failure mechanisms. The effects of different bolt patterns on roadway behaviour were evaluated. Comparison between the model results and the field measurements indicated that that the model effectively simulated the critical elements of the actual roadway’s behaviour. With the confidence gained, the model was used as a baseline for additional simulations that evaluated the expected performance of alternative roof support systems. The study will also provide a benchmark data set for future applications of numerical modelling to U.S. coal underground mining.

By Maria I. De Rosa

This report analyzes mine fires for all U.S. underground and surface coal mining categories by state and2-year time periods during 1990–1999. Risk rate values are derived, and ignition source, methods of fire detection and suppression, and other variables are examined. The data were derived from Mine Safety and Health Administration (MSHA) mine fire accident publications and verbal communications with mine personnel. The analysis will provide the National Institute for Occupational Safety and Health, MSHA, and the mining industry with a better understanding of the causes and hazards associated with mine fires and will form a basis for future fire research programs.

Jan 9, 2004

This Information Circular from the National Institute for Occupational Safety and Health (NIOSH) documents and supplements the information presented in a series of workshops held during 2002 and 2003. The primary intended audience consists of all who are involved in developing and conducting miners? training. According to the Mine Safety and Health Administration (MSHA), mine operators reported 240,000 full-time equivalent workers and independent contractors reported 42,000 full-time equivalent workers working on mine property during the year 2000. Unfortunately, these workers have a relatively high risk of suffering serious work-related injuries and illnesses. The mining industry has the highest rate of occupational fatalities among all U.S. industries. The fatality rate is 30 deaths per 100,000 workers compared to 4.6 for all private industry(Morbidity and Mortality Week Report, 2001; NIOSH, 2002).Compared to workers in other industries, miners also have a relatively high rate of nonfatal lost-time injuries, and their injuries tend to be more severe (Bureau of Labor Statistics, 1999). Many miners are also exposed to significant health hazards, including coal and silica dust, diesel exhaust, and noise. More than 1000 U.S. miners die of lung disease each year(NIOSH, 1999).

Jan 1, 2002

Now you know why there is concern about mine illumination. You have some idea about how the human eye works and about the problems of glare, peripheral vision, and accommodation. And you know that lighting in a mine presents special problems because of the dark surroundings and low reflectance. This chapter describes what can be done to improve conditions. This chapter begins with a short discussion about Federal Standards on mine lighting -- what they are and what is being done to carry them out. The chapter then describes different types of lamps that can be used for mine lighting, and discusses their advantages and disadvantages. Finally, the chapter lists some things that you can do personally to improve lighting, or can point out to others so that improvements can be made. The Federal Government is doing its part to improve mine lighting by establishing regulations. Lamp manufacturers are constantly studying new lamps to provide better equipment. And your company will do its part to comply with regulations. Better lights may not be here yet, but they will be soon. But in the end, you are the one who will be using the lights, and you are in the best position to see the improvements. You are also in the best position to see and tell others where further improve¬ments can be made.

Jan 1, 1976

By Harold R. Newman

The performance of Ecuador's mineral industry continued to be affected not only by depressed oil prices in recent years but also by natural disasters. In March 1987, Ecuador canceled foreign debt payments for the rest of the year and appealed for international aid because of a series of earth-quakes that destroyed villages and crippled the nation's oil industry. The earthquake destroyed a key section of the country's main oil pipeline and forced a halt to production and shipment of Ecuador's most important export product. Ecuador produces 240,000 barrels of oil per day and exports 144,000 barrels daily. Oil accounts for 60% of the nation's hard currency earnings. The Government of Ecuador asked the Organization of Petroleum Exporting Countries and other oil-producing countries to assume Ecuador's oil sales commitments. Ecuador agreed to pay the countries back in an equivalent amount of oil when it was able to resume exports.

Jan 1, 1989

By Bruce T. Olenchuk, Wils L. Cooley

Electrical grounding is essential for the safe operation of power systems. A low-impedance path to ground is necessary to prevent the possibility of dangerously high potentials in human work areas. If for any reason this ground connection becomes faulty, a serious hazard may exist. One reason for faulty ground connections is ground bed corrosion. Corrosion of electrical ground rods has plagued the power industry and appeared in coal mine power systems. This paper will investigate ground rod corrosion, its cause, and possible solutions. Included is an evaluation of various ground rods for their ability to resist corrosion under stray current conditions. -The first known study of X-it3 Rod Corrosion is also presented.

Jan 1, 1979

By Gregory J. Chekan

In order to reduce waste and improve resource conservation, mine planning, and development, the U.S. Bureau of Mines is investigating multiple seam interactions associated with longwall mining. Longwall gate entry and panel stability have been influenced by previous mining in coalbeds above and below a mine in Virginia that operates in the Lower Banner Coalbed. Directly superjacent, approximately 115 ft, the Upper Banner Coalbed has been partially worked by room-and-pillar mining. Directly subjacent, approximately 730 ft, the Tiller Coalbed has been worked by partial room-and-pillar retreat mining. The study mine has experienced problems during development of gate entries in areas of overmining and undermining. It is anticipated that stress fields associated with adjacent mining may further affect gate entry stability and face advancement during the extraction of the longwall panel. To assess overmining and undermining effects on ground stability, the Bureau gathered geotechnical information at the site. Headgate entries and pillars were instrumented and monitored to study loading behavior as the longwall face approached and passed potential problem areas. Measurements indicate that although increases in average pillar pressure were greater than predicted values, previous mining in adjacent coalbeds had little effect on headgate stability.

Jan 1, 1989

By Parviz F. Rad

The Bureau of Mines conducted groove cutting experiments in marble, lime-stone, granite, and quartzite with a 7-inch disk cutter under a normal thrust of 7,000 lb. The values of muck weight per unit length, specific energy, cutting coefficient, and groove depth for each of these rocks were determined for groove spacings ranging from 0.1 to 4 inches, and from these results the values of optimum and critical spacing were computed" The results indicate that compressive strength may be used to predict some of the cutting characteristics of the independent grooves. Considering all the cutting characteristics, particularly those for the interacting grooves, Shore hardness, coefficient of rock strength, and torsional velocity correlate with cutting characteristics better than do other physical properties. Some of the field applications of the principles established in this report are identified.

Jan 1, 1974

The current procedure for measuring the concentration of respirable coal mine dust is as follows. Each filter is preweighed by the filter manufacturer to ±0.1 mg. Following sampling with the Coal Mine Dust Personal Sample Unit (CPSU) at 2.0 L/min, the filter with coal mine dust is sent to MSHA for weighing. The current MSHA procedure for weighing respirable dust samples uses a Mettler Model AE163 analytical balance in conjunction with an automatic weighing system with a precision of ±0.02 mg [Tomb 19901. Each balance is calibrated twice per day. Quality control for the automatic weighing system includes the systematic weighing of one in eight filters on a second Mettler AE163 balance. Tolerance is set at ±0.1 mg between the two weighings of the same sample. Weights are truncated at the 0.1 mg level (e.g., 3.457 mg is truncated to 3.4 mg) [Bowman et al. 19851. The difference of the two truncated weights is then recorded as the weight of coal dust deposited. The respirable concentration (mg/m3) is computed by multiplying by a correction equal to 1.38 and dividing by the volume of air sampled (2.0 L/min x sampling time [min]).

Jan 1, 1997

By M. L. Whisman

Several commercial processes for reclaiming used lubricating oil were duplicated on a laboratory bench scale. Laboratory tests were selected and in some instances modified to determine the physical properties of each oil produced. In addition, the hydrocarbon composition of some samples was determined using a liquid chromatographic technique, and compared with the composition of new oil in order to determine the severity of the re-refining technique. Selected samples of reprocessed oil were reformulated with an additive package for further estimates of quality as determined by wear, corrosion, foaming, and oxidation stability tests. Additionally, several samples of commercially re-refined oil and new oil were obtained and physical properties were determined for comparative studies.

Jan 1, 1974

By B. W. Jong

The U.S. Bureau of Mines investigated anhydrous chlorination and caustic-acid leaching processes to recover Ni, Co, Mo, and W from waste hydroprocessing catalysts. In batch laboratory-scale equipment, the chlorination process extracted 61 to 99 pet of the metals. Final recovery was 65 to 99 pct. The caustic-acid leaching process extracted 81 to 98 pct of the metals. Final recovery was 36 to 99 pct. Chlorination processing included roasting, chlorination, hydrolysis of metal chlorides for recovering Mo or W, water leaching of Ni or Co from the spent charge, purification, and solvent extraction or precipitation of Ni or Co from the purified solutions. Caustic-acid leach processing included NaOH leaching, solvent extraction of Mo or W from the NaOH leach liquor, H2S04 leaching of the NaOH leach residue, purification, and solvent extraction or precipitation of Ni or Co from the purified solution. The estimated fixed capital cost for a commercial-scale plant processing 39,000 Ibid of waste Ni-Mo-AI catalyst was $8 million for the chlorination process and $9.6 million for the caustic-acid leaching process. The estimated operating cost was about $0.20 and $0.40 per pound of the waste catalyst, respectively, for the two processes.

Jan 1, 1989