Search Documents

Reduce longwall shearer operators' dust exposures by more effectively suppressing the dust generated by the upwind cutting drum. Approach Direct more of the shearer water supply to the upwind drum, thus reducing the shearer operator's exposure to respirable dust while making more efficient use of water. How Proportioning Permits More Efficient Use of Water On most longwall mining operations, the cutting action of the shearer drums is the primary source of dust. Al-though the amount of dust generated is directly related to the amount of coal and rock cut by the drum, the exposure or the shearer operators to dust depends more on their work position relative to the upwind drum. When cutting with the airflow, the upwind drum, cutting bottom coal and floor rock, is the primary generator of dust reaching the operators. The lead drum is downwind of both shearer operators and is thus of less concern. (See diagram). When cutting against the airflow, the lead drum is upwind-taking a full cut, including roof rock-and both shearer operators may be exposed to very high levels of respirable dust. Currently, water sprays mounted on the cutting drum provide the most effective method of controlling dust from longwall shearer drums, and all longwall mining operations use some type of bit flushing or cavity filling water spray system on the cutting drums. Bureau surveys of longwall operations, conducted as part of its research program to reduce respirable dust, have indicated that six longwalls with better than average compliance records use higher than normal water flowrates to the cutting drums. The average water flow to the shearers at these six operations was approximately 60 gpm-about 50 percent more water than is normally supplied to double-drum longwall shearers.

Jan 1, 1982

By Charles L. Kimbell

For 1991, the aggregate value of world international export trade in mineral commodities was roughly estimated at $685 billion in current 1991 dollars. The estimated level was about 6 % higher than that for 1990, but still more than 3 % below the record high set in 1980, and the year was the fifth in a row in which the value of exported minerals advanced. Table 8 provides a data series for the estimated value of world export trade in all mineral commodities from 1979 through 1991, as well as a breakdown of this total into fuel and non fuel commodities. The data shown are based on the historically more traditional and realistic (from the viewpoint of data availability) practice of reporting trade values for the year before the year of review. Despite the considerable increase in the dollar value of mineral commodity exports, their share of total export merchandise trade declined to 19.1 % in 1990 from 19.7% in 1989. At 19.1 %, this share was very near the recent year record low of 19.0% reached in 1988. Comparable 1991 figures were not available in time for inclusion here, but it is expected that the mineral commodity share of the total will be little altered from that of 1990.

Jan 1, 1993

By Michael J. Brnich

Since 1991, Pittsburgh Research Center (PRC-formerly part of the Bureau of Mines) researchers have recorded extensive interviews with 30 individuals who are experts in the area of mine emergency response. These individuals, who have an average of 35 years of mining experience and 29 years of mine emergency response experience, related stories and observations from events that they experienced during their combined 850 plus years in mine emergency response. The purpose of this effort was to gather information that could be passed on to both today?s and tomorrow?s mine emergency responders to train and guide them in handling future events. This is the first of two articles which report the responses that these experts gave when asked how they think people who may have to respond to a future mine emergency should be trained. During the interviews they discussed how training should be conducted, who should be trained, and what topics should be included. This article will cover the first two areas: what training methodologies would be most effective and who needs to participate.

Jan 1, 1997

By J. E. Chilton, Jr. Dubaniewicz

Many mines rely on toxic gas sensors to help maintain a safe and healthy work environment. This report describes a prototype monitoring system developed by the U.S. Bureau of Mines (USBM) that uses light to power and communicate with several remote toxic gas sensors. The design is based on state-of-the-art optical-to-electrical power converters, solid-state diode lasers, and fiber optics. This design overcomes several problems associated with conventional wire-based systems by providing complete electrical isolation between the remote sensors and the central monitor. The prototype performed well during a 2-week field trial in the USBM Pittsburgh Research Center Safety Research Coal Mine.

Jan 1, 1995

By P. W. Jeran, S. J. Pepperney, M. C. Irani, F. F. Kopsch

The Bureau of Mines has designed and put into operation a fail-safe control system for use in underground coal mines equipped with methane drainage pipelines. This control system can detect certain unsafe conditions and respond by automatically shutting off the flow of methane from the degasification borehole to the drainage pipeline. Methane flow is shut off when the methane content in the return airways reaches a predetermined level (typically 1.5 pct), when the methane drainage pipeline is ruptured by roof fall, or when there is an electric power failure. The fail-safe control system was designed using commercially available components and a methane analyzer system previously developed by the Bureau. The fail-safe system consists of a unit that combines a shutoff valve and pneumatic valve actuator, and electronic and mechanical equipment designed to detect hazards and effect shutdown. The fail-safe control system was designed to meet regulatory requirements issued by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and State regulatory bodies for the safe operation of underground methane pipelines used for mine degasification. MSHA has inspected and tested this system and permitted its use in two mines. The Bureau installed the fail-safe system in two working coal mines, where successful performance has been demonstrated.

Jan 1, 1980

By D. R. Douslin

This report describes an inclined-piston pressure gage that operates from a zero-pressure datum level. The gage is adaptable to accurate vapor-pressure measurements in the low and intermediate pressure range, 0.01 to 40 mm (mercury). Residual friction in the oil-lubricated piston-cylinder combination is eliminated by a unique oscillatory method that is free of end thrust on the piston and allows the full sensitivity of the gage to be realized. The axial component of the weight-to-area ratio of the piston is determined by measuring the angle of inclination with a goniometer that can be read to 1 sec. Accuracy of the gage proper is estimated to range from 0.001 to 0.012 mm from lower to upper pressure limits. Its highest practical sensitivity is about 0.0005 mm. As a test, the vapor pressures of ice and water were measured in the range -30° to +20° C.

Jan 1, 1963

By F. Chase, D. Pappas

Pillar recovery has been associated with nearly one third of roof fall fatalities in underground coal mines during the past decade. Safe pillar recovery requires global stability and local stability. Global stability is addressed primarily through pillar design. The local stability risk factors include cut sequence, the final pillar stump, supplemental supports (timbers vs. Mobile Roof Supports (MRS)), roof bolting, and many others. The National Institute for Occupational Safety and Health (NIOSH) has evaluated each of these factors through field research and analysis of accident statistics. The paper discusses design methods and technologies that have been transferred to the mining community and implemented.

By Tobias W. Goodman

The U.S. Bureau of Mines used a contact drilling strategy with short-collared assemblies in order to rotary drill long horizontal methane drainage holes in the Beckley Coalbed near Glen Daniel, WV. By decreasing the thrust, and increasing the rotation of the drill bit when in contact with the roof and floor rock, assemblies with 1-ft (0.3-m), 10-ft (3- m), and 144 (43-m) long collars were made in deflect and stay in the coalbed. Successful application of this procedure resulted in holes drilled full length in coal with the original assembly including bit. The test assemblies deflected away from the original bearings of the holes during drilling and arced. Four holes were drilled to depths ranging from 478 ft (145.7 m) before the strategy was developed, to 4,034 ft (1,230 m) when the strategy was applied. Total length of the holes in coal was 8,590 ft (2,618 m). After 577 days the total methane captured by the holes was 221,600,000 ft? (6,276,000 m3). The methane flow rate peaked at 805,000 ft3/d (22,798 m3/d), then decreased to stabilize at 670,000 ft?/d (18,974 m3/d) after 6 months.

Jan 1, 1989

By R. P. Beyer

[The Bureau of Mines has measured the low-temperature heat capacities and high-temperature enthalpies of crystalline K2Si2O5 as part of a program for advancing mineral resources technology with energy economy. High-temperature enthalpies of glassy and liquid K2Si2O5 and crystalline K2SiO3 were also mea¬sured. An adiabatic calorimeter operating over the range 5 to 308 K was used for the heat capacity measurements for K2Si2O5 from which the standard entropy at 298.15 K, S°298 = 45.55 ±0.05 cal/deg-mole, was calculated. Tabulated values of Cp°, S°, -(G° -HO°)/T, and H°-HO° from 5 to 300 K are given for K2Si2O5. A copper-block drop calorimeter was used in the enthalpy measurements, operating from 298.15 to 1,198 K for K2SiO3 and from 298.15 to 1,453.8 K for K2Si2O5. No transitions were found for K2SiO3. The KI2Si2O5 showed two reversible first order transitions, one at 510 K with a heat of transition of 0.29 kcal/mole and one at 867 K with a heat of transition of 0.38 kcal/mole. The heat of fusion for K2Si2O5 20 5 was calculated to be 8.42 kcal/mole. Relative enthalpies are given in equation form, and high-temperature values are tabulated for Cp°, S°, - (G°-H°298 )/T, and H°-H°298 . Also tabulated are ?H°, ?G°, and log K for formation of K2SiO3 and K2Si2O5 from both the elements and the oxides.]

Jan 1, 1979

By F. Garcia, J. Cervik

The cross-measure borehole technique has been shown by the Bureau of Mines to be an effective method of controlling methane liberated by fracturing the roof strata in longwall gobs where overburden is less than 750 ft (229 m). Boreholes are drilled into roof strata before mining operations affect the roof strata. Longwall mining fractures the roof strata and releases methane from source beds. Surface exhausters or vacuum pumps are used to draw the gas to the surface through an underground pipeline and vertical exhaust hole. The captured methane is thus prevented from entering the mine's ventilation system. About 71 pct of the methane produced by longwall mining in the Lower Kittanning Coalbed was captured by the cross-measure boreholes. Borehole spacing is an important factor affecting the performance of the technique. Interference tests and measurements of methane flows in return air indicate borehole spacing in the Lower Kittanning Coalbed should be limited to about 200 ft (61 m) except on the first 600 ft (183 m) of the longwall, where spacing should be reduced to about 100 ft (30 m) to capture the large quantities of methane released when the first large roof fall occurs. Comparisons between measured and calculated gas pressure differentials on boreholes indicate borehole length can be reduced from 280 to 140 ft (85 to 43 m), which reduces drilling costs significantly. Additional experimentation is necessary to verify the calculations.

Jan 1, 1985

By James H. Russell

Several solid sorbents were compared for their effectiveness in removing sulfur dioxide from flue gases. The materials were tested for the rate of sorption and capacity at about 300° C, and rate of regeneration around 700° C in thin beds and in 4-inch-diameter fluidized beds. Rates of material loss were also estimated. The sorbents tested included three samples of alkalized alumina, two samples of sodium carbonate-impregnated alumina, and one proprietary sample of porous silica impregnated with copper and iron compounds. The results showed that all the alkalized aluminas had good sorption capacities and rates, required high temperature regeneration, and suffered excessive material loss; the sodium carbonate-impregnated aluminas (1) had high sorption rates but barely adequate capacities, (2) required high temperature regeneration, and (3) suffered excessive material losses; and the copper-iron impregnated silica suffered only slight material loss and could be regenerated at a relatively low temperature, but the sorption rate and capacity were too small. None of the sorbents met all the arbitrary performance criteria that follow: sorption rate constant of 1 min-1, sorption capacity of 0.1 g sulfur per g sorbent, regeneration rate constant of about 0.075 min-1 at a reasonable temperature, less than 0.07 pct per hour material loss during operation, and a chemical life of 500 cycles.

Jan 1, 1971

By Franklin D. Cooper

This chapter includes tables for 1979 that were not available in time for publication in the 1978-79 Minerals Yearbook, but it does not include corresponding tables for 1980. The value of raw nonfuel mineral output in 1980 was estimated at $24.8 billion, 8.5% above the 1979 value. Of the 21 metal commodities produced, quantitative output increased for 11 and decreased for 10. The values for 10 metals were up, 10 were down, and 1 was unchanged. Among the 47 non-metallic commodities produced, 14 showed quantitative increases, 32 declined, and 1 was unchanged. In terms of value, 32 nonmetallics increased, and 15 declined.

Jan 1, 1981

By Donald A. Wilson

As part of a continuing effort to maximize metal recovery from domestic secondary resources, the Bureau of Mines investigated a process for recovering the metallic portion of scrap alkaline batteries. A pyrometallurgical method for recovering nickel and cadmium from Ni-Cd scrap batteries previously developed on a laboratory scale, was scaled up to 25-and 43-pound charges. The method employed reduction and/or decomposition in a retort using a minimum of 2.5 percent carbon as a reductant. Metallic cadmium was distilled at atmospheric pressure and a minimum of 900° C. Purity of the recovered cadmium was 99.8 percent minimum and the nickel-iron residue contained less than 0.02 percent cadmium.

Jan 1, 1981

By Jeffrey B. Osmint

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority fur the Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96479, 96th Congress), which strengthens protection fur proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1991

By Charles C. Boley

The Bureau of Mines dried and carbonized two wood wastes, one softwood (redwood) and one hardwood (oak), using continuous, vertical entrainment techniques previously developed for use with coal. It was demonstrated that these techniques are readily applicable to wood waste and that appreciable changes in the yields of carbonization products can be obtained by varying operating conditions. A limited amount of experimental work was done on briquetting the char-coals. Firm briquets were formed with oak charcoal, although greater quantities of starch binder than used commercially for kiln-produced charcoal were required. Redwood charcoal did not briquet successfully under the test conditions employed.

Jan 1, 1969

By H. H. Fields, T. W. Goodman, Joseph Cervik

The Bureau of Mines conducted research to determine the effectiveness of long holes drilled in solid virgin coal in degasifying an area of the Pitts- burgh coalbed showing that horizontal holes drilled into a virgin coalbed from the bottom of any shaft will effectively remove methane gas in commercial quantities from the Pittsburgh coalbed. The in situ pressure at a depth of 214 feet into the coalbed and the average gas and water flows from the five degasification holes were 3 lb/in2 gage and 860,000 ft3/d and 1.7 gal/min, respectively. On June 19, 1975, after 593 days of degasification, a compressor was installed and pipeline quality gas was introduced into a commercial pipeline. As of June 1, 1976, after 1,022 days of degasification, over 753 million cubic feet of gas had been drained and 117 million cubic feet of gas had been purchased by the gas company for use in the local community of Wadestown, W. Va. The gas drained to date is six times the gas estimated to be in the area subtended by the holes. Methane emissions at the working face of 1 West mains, Federal No. 2 mine has been reduced by 50 pct, proving the value of methane drainage by horizontal degasification holes drilled from shaft bottoms ahead of mining.

Jan 1, 1976

By Robert L. Lagace

The attention of this group was focussed on four through-the-earth communication systems that are presently of high interest to the U.S. Bureau of Mines; four systems for providing operational/emergency communications on the working sections of coal mines, indeed up to the very face of the section. The systems are: uplink-data, downlink-voice, sidelink-call alert coded page, sidelink-roof bolt voice page. Each of these systems makes use of the mine overburden as the signal transmission medium, as opposed to the guiding wires, cables, and tunnels treated by the operational communications working group. Each of these systems satisfies one or more of the Bureau's objectives for mine communications systems; namely • reliable links for monitoring the mine environment under both operational and emergency conditions. • reliable links for communicating with miners during emergencies. • special links for increasing the efficiency of day-to-day operations of the mine. Each of these systems has been successfully demonstrated on a limited experimental basis, and prototypes of all these systems are installed and operating in the USBM experimental mine in Bruceton, Pa. Each of these systems must now be optimized regarding its performance, and engineered for practical routine application to the working sections of actual operating coal mines, particularly those of the room and pillar type. This optimization and engineering must take place subject to the principal constraints listed by Howard E. Parkinson in his Workshop paper entitled, "Objectives and Constraints of Through-the-Earth Electromagnetic Communications Systems'' and enumerated below. • Depth of Mine Overburden • Overburden Conductivity • Electromagnetic Noise In and Above Mines • Limited In-Mine Electrical Energy (Stationary or Man Carried) During an Emergency • Intrinsic Safety for In-Mine Equipment • Practical and Rugged Equipment for Use Under Both operational/Emergency conditions • Severe Weight Limitations for Man Carried Equipment • Reasonably Low Costs Especially for Man Carried Equipment Part II of this paper provides a brief description of each system, while Part III summarizes the present status of developments related to these systems and some recommendations for future work needed to advance these systems to the practical application stage.

Jan 1, 1973

By C. B. Manula, R. L. Sanford, R. A. Rivell

The need for a large capacity, high speed computer is more apparent in the revised model than in the original one. Core storage requirements for data and model logic have at least tripled. This dictates the use of one of the large modern machines such as the IBM 360-370 series or the Univac 1108 and 1110, which handle the model without the need for extensive program overlay. Computer time is expensive on these machines, however, and comprehensive analysis has gone into optimizing computer execution time consistent with model information flow sensitivity. For example, revised locomotive tramming routines have been developed which will significantly cut execution time compared to the previous version. Transceiver Applications The computer coding for the model has been developed to enable program execution and testing using a remote terminal on a time sharing system. In fact, nearly all of the coding, debugging, testing and modifications have been performed from a terminal during develop¬ment. The gaming options described in the Model Input Section of this report have been designed so that they are easily changed by the user from any remote site. One restriction on remote applications which could arise, however, is where highly detailed output options are specified, resulting in a large amount of output records which could be handled more efficiently on a high speed printer.

Jan 1, 1974

By James A. West

THE South Asian countries of India, Ceylon, Pakistan, Afghanistan, Nepal, Bhutan, and Sikkim have a large variety of mineral resources; however, in spite of mineral industry growth during 1964, development of resources remained far short of possible development, and, in terms of value of trade in minerals, the area remained a sizeable net importer. India's mineral industry is by far the most significant; its minerals production in 1964 accounted for more than 90 per cent of the total value of all minerals produced in the area. The total value of all minerals produced in South Asia in 1964 was only about 1 percent of the area's estimated gross national product of $55,125 million. Despite the rather small current contribution of minerals to the economy, development of mineral resources figures prominently in plans for the industrial development of the nations of this area.

Jan 1, 1966

By George H. Schnakenberg, Aleksandar D. Bugarski

This report reviews the performance and applicability of technology for the control of emissions from diesel-powered equipment used in underground coal and metal/nonmetal mines. The methods discussed include Mine Safety and Health Administration-approved low-emission engines, engine derating, fuels, fuel additives, diesel oxidation catalysts, and diesel particulate filters. The potential of each of these technologies is examined individually and in combination. The performance estimates are derived from the published literature and presented in narrative and Tabular form. The purpose of this report is to help the mining industry select the most appropriate method to reduce underground exposures of miners to diesel exhaust in the context of the recently developed diesel regulations. It is important to note that the control technologies discussed in this report have received limited evaluation in underground mines. Additional research is ongoing, and some engineering design changes may need to be implemented before all of these diesel emission control technologies can be safely and successfully used in underground mines.

Jan 1, 2002