Search Documents

By D. Hinton, M. McCawley, R. C. Lantz, F. Pisano, C. Stanley

"INTRODUCTION Aerosols (5 um have not been shown to be consistently generated and characterized in inhalation chambers. Particle deposition in the lungs however may occur with particles as large as 25 um(1). Therefore, in order to closely simulate the atmosphere of an underground coal mine where the distribution is bimodal, with modes at S and 15 um (2), particles much greater than <1 um must be characterized for uniform mixing and size distribution within these chambers. The Hazelton Animal Exposure Chamber has been chosen because it has been best characterized for smaller particles (<1 um) (3), and is the major type used by most inhalation toxicology institutes such as Lovelace Inhalation Toxicology Institute and Battelle Northwest Laboratory.BACKGROUNDPreviously published studies on the inhalation of solid aerosols have attempted to characterize the distrition of particles of <2 um in diameter. There are no published reports of extensive work characterizing either the size distribution of particles <1 um or the concentration throughout the exposure chamber (Table 1).Table 1 shows the variability and sizes of several aerosols <1 um in diameter used in five previous chamber studies.Discussion of Previous StudiesThe study done by Bauermash, Bryan, Dickinson, and Burke (4)stated two major concerns in the development of the 6.5 ft. diameter chamber. The first was that a quantity of animals could be exposed to the same concentration regardless of the location of the animal, and second was that the chamber could be easily cleaned and decontaminated. The solution to the first concern required a circular chamber with the contamination air entering the chamber somewhere along the central axis. The animals could then be changed during exposure time so that each animal was exposed throughout the total volume."

Jun 1, 1988

By J. Mutmansky, C. Lee

"The size distribution of coal mine dust is one of its most important characteristics because the particle size is known to govern the region of deposition of dust within the human respiratory tract. In addition, dust characteristics, particle settling rate, transportability of the dust and the efficiency of dust control measures are all affected by the particle size. As a result, particle size distribution of the airborne dust in a coal mine is a fundamental property that impacts on the health of underground workers.This paper deals with some basic findings on the size distribution of cool mine dust based upon the results of data collection in six underground coal mines using continuous miners. All airborne dust sampling was performed on development sections using eight stage cascade impactors and permissible 2. O l / min pumps. Samplers locations were fixed in the sections with respect to the continuous miner and roofbolter or with respect to the intake and return airways • Sampling times varied from 45 minutes to 6 hours , depending upon the dust concentration. The first topic of analysis was the test to determine whether the commonly used lognonnal distribution is valid when applied to airborne coal mine dust. Secondly, the conventional method of representing the· distribution using two parameters, the geometric mean and the geometric standard deviation, is questioned. Since almost all size data were found to show some degree of bimodality, the two parameter lognonnal distribution may not represent the total airborne coal mine dust size , quite adequately. Bimodal lognonnal distribution was tested to be a good approximation in the case with two modes in the size distribution.The final topic discussed in this paper is the 'locational variation of the airborne dust size distributions within the continuous mining section. The size distributions varied considerably at the different sampling locations with the continuous miner and roofbolter producing the coarser distributions. Fine size modes in the range of 2 to 4µ m including mostly respirable dust particles were present in almost all samples • Second dust generating sources such as the shuttle car movement were found to be major causes of high respirable dust concentrations in some cases ."

Jan 1, 1988

By P. D. Kovscek

High-pressure streams of water, known as water jets, can be used to improve the cutting efficiency of mechanical bits. During prior testing by the Bureau of Mines, the cutting performance of a longwall shearer, equipped for water-jet-assisted cutting, was evaluated. The performance of the shearer did not improve while using water jet assist because the pressure of the water delivered to the rock surface was inadequate. The study, described in this report, resulted in a determination of the major cause of water pressure loss on the shearer, and an evaluation of the techniques for increasing the water pressure at the rock surface. The results show that the major pressure loss, which occurred between the nozzle and rock surface, is directly affected by the amount of fluid turbulence that develops just upstream from the nozzle. Preventing a sudden change in the direction of the flow channel can increase the stagnation pressure as much as 400 pct. Smoothing the surface of the flow channel in the shearer bit block would increase the stagnation pressure delivered to the rock surface by 35 pet.

Jan 1, 1989

By J. M. Mutmansky

"This study analyzed laboratory comminution techniques for respirable mine dust generation and the properties of the resulting dusts. It was the objective of the study to determine the suitability of the resulting dusts in reflecting the properties of natural airborne dust. This paper deals specifically with the amount of contamination introduced into the generated dust as a result of abrasion when using nine different grinding methods. The analysis was made by comparing the content of 25 chemical elements in the lab-generated dusts with the same elements in the airborne coal mine dusts. It was found that all the lab-generated dusts possessed contamination but that several methods produced smaller percentages of contamination and that the residence time in the grinding device was an important factor in the contamination levels. INTRODUCTIONDust in the atmosphere is a health hazard and a major source of occupational diseases in the coal mining industry (Anon., 1980; Merchant, Boehlecke, and Picket-Hamer, 1986). It has been shown that coal workers' pneumoconiosis (CWP) is directly related to the inhalation and accumulation of respirable coal dust in coal miners' lungs. In order to effectively protect coal workers from coal dusts, we must have a clear understanding of dust properties including dust generation and dust-lung reaction mechanisms. This requires extensive biomedical research. Dust related research often requires large samples of respirable coal dusts to be collected, either for repeated experiments or stored for future reference. Unfortunately, current sampling instruments are not able to meet this demand. Ali a result, laboratory-generated coal dust ls frequently used as a substitute for coal mine dust in biomedical and other research applications. Now, the questions are how close the characteristics of laboratory-generated dusts are to those of mining-generated dusts and which equipment is moat appropriate for research dust production in the laboratory . These are some of the interests of this research project. The primary objective of this project was to find a laboratory technique which can generate coal dusts possessing properties similar to coal mine dust with respect to particle size distribution, chemical composition, and particle shape and morphology. However, this paper will focus only on the chemical compositions of the prepared dust samples and try to identify the sources of chemical contamination from various size reduction processes."

Mar 1, 1992

By Ronald T. Mayerle

There are no producing or developing mines in the Rattlesnake RARE II area. Specific areas with mineral occurences are prospects for: 1) stratabound copper and silver in Belt sedimentary rocks on the northwest border of the study area; 2) base metal sulfides, in thin veins and shear zones in Belt sedimentary rock, and diabase dikes and adjacent metasedimentary rocks in the southern part of the study area; 3) barite in sedimentary rocks near Rattlesnake Creek and Sheep Mountain; 4) limestone near Rattlesnake Creek and Blue Point; and 5) silica in quartz veins near the headwaters of Rattlesnake Creek and Sanders Lake. Stone, sand and gravel suitable for construction material are in the study area; however, equal or better quality deposits are common throughout the region. The RARE II area has no known oil and gas, coal, or geothermal energy deposits.

Jan 1, 1983

By Laxman S. Sundae

In the vast majority of American coal mines, roof bolt holes are drilled dry, mainly because of mine operator concern with the spent water creating adverse working conditions. Wet drilling, however, can increase drilling rates and the effective lifetime of the drill bits used. This study, carried out as part of an ongoing cooperative research program between the U.S. Bureau of Mines and the University of Missouri-Rolla, shows that the large volumes of water conventionally used in wet drilling are not necessary, and the performance benefits from wet drilling can be achieved with total volume flows on the order of 0.4 L per hole. This conclusion is validated based on the measured respirable dust generated in drilling Berea sandstone. The results are confirmed using a variety of bit shapes, which are also shown to have a significant effect on penetration rate.

Jan 1, 2010

1. Data from the Mine Safety and Health Administration (MSHA) indicate that a total of 241,502 employees worked in surface mining locations in 2003, corresponding to 212,113 full-time equivalent (FTE) workers. • Surface employees accounted for 84.6% of all mining employees. • The majority of surface employees (73.7%; n = 177,927) were mine operator employees as opposed to contractor employees. • Stone operator employees comprised the greatest percentage (27.2%; n = 65,743) of surface employees.

Feb 1, 2005

By Kyei-Sing Kwong

The U.S. Bureau of Mines investigated the synthesis of advanced ceramics (SiC+AlN, SiAlON, SiC+A1203, and Si3N4+AlN) from natural clays (kaolin, halloysite, or montmorillonite) by an intercalation and heat treatment method. This process includes the steps of refining a clay, intercalating organic chemicals into its layered structure, drying the intercalated mixture, firing the treated structure at certain temperature ranges in controlled atmospheres to form desired compounds, and grinding the loosely agglomerated structure. Focus of this research is to economically process advanced ceramic structures from abundant natural resources. The advanced ceramic phases produced in this simple treatment are homogeneously distributed at the nanostructure level, and may potentially lead to cost effective manufacturing processes. The intercalation of clay was confirmed by X-ray and BET analyses. The evolution of chemical compositions during carbonization reactions and carbothermal reduction was investigated. The characteristics of refined clays and synthesized powders were studied. Advanced ceramic composites/solid solution have been produced from intercalated clays, without the presence of other compounds.

Jan 1, 2010

By NIOSH Publications

In 2004, 14,478 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). Almost half (48.9%) were sand and gravel mines, followed by stone mines (30.4%), coal mines (13.9%), nonmetal mines (5.1%), and metal mines (1.7%).

Sep 1, 2007

By Christopher Van Dyke, Knox Van Dyke, Lixin Wu, Jaime Gutierrez

"I. INTRODUCTION(SILICA, THE LUNG, INFLAMMATION, AND FIBROSIS)Inhalation of respirable-size silica (0. I to 5 µm in diameter) deposits the particles in the deep spaces of the Jung where oxygen is exchanged. The resulting pattern of inflammation is substantially different compared to that observed from other inhaled substances such as carbon, polystyrene titanium dioxide etc. 1 Following the inflammatory reaction the body attempts to isolate the damage by walling off the area via fibrosis. 2 The unique nature of the inflammatory response to silica makes it logical to infer that fibrosis is a later-stage manifestation of the initial inflammatory damage. In addition to the inflammation extensive lysis and cellular death particularly to macrophages and neutrophils, can occur, depending on the dose of silica.' The ingestion of significant amounts of silica by macrophages and neutrophils produces an inflammatory sequence which activates the lipoxygenase pathway of arachidonic acid metabolism and produces platelet activating factor (PAF) and leukotrienes (LT).4·5II. CALCIUM IONOPHORE MIMICS SILICA TOXICITY IN VITROPhagocytic cells exposed to silica in vitro produce PAF and LT. This response is reminiscent of phagocytic cells exposed to the calcium ionophore (A23 l 87) in the presence of ionic calcium.6-8 A23 l 87 forms a complex with free ionic calcium which passes through cellular membranes, thus transporting calcium inside the cell. The increased intracellular calcium concentration triggers the production of small amounts of prostaglandins large amounts of LT. PAF and. depending on dose cellular death (see Figure 1 ). Could silica cause LT production and cellular death by a similar mechanism? How could silica - an inert solid - act in a similar fashion as a soluble stimulant? Clearly the negative SiO2 and OH- surface of silica can bind calcium ions9 and therefore could theoretically act as a solid-state ionophore releasing bound calcium inside of cells following phagocytosis."

Jan 1, 1998

By Jun Yi

In this paper, single-component gas sorption and transient diffusion processes are described within coal matrix exhibiting bimodal pore structure. The coal matrix is treated as a poroelastic medium manifesting swelling and shrinkage effects due to the sorption of gas under effective overburden stress. Gas transport is considered Fickian with molecular (bulk) and surface diffusion processes simultaneously taking place in the macro-and micropores of coal, respectively. The numerical formulation is intended to be explicit in nature to investigate the influences of sorption phenomena on the macropore volumes and on the overall gas transport for the cases of gas uptake by and release from coal. Results of the study show the presence of hysteresis during a sorption?desorption cycle of the gas. It is also found that the overall gas transport takes place at a rate significantly less than that in the macropores only. Thus the existence of a retardation effect in the overall gas transport is concluded. This retardation effect is primarily due to the micropore resistances, in particular gas adsorption, and is independent of the changes in the macropore volumes. It is shown that macroporosity of the coal matrix may change during gas transport due to combined effects of pressure and sorption-induced swelling or shrinkage of the coal. It is estimated that the macroporosity variation is non-uniform in space and time, as it is expected in reality, and typically taking values less than ±10 percent of the initial porosity.

Jan 1, 2009

In the United States water pollution resulting from mining activities has long been recognized as a major environmental problem Mine drainage pollution results from many types of mining activities and includes both physical (i e , sedimentation) and chemical (i e , acidification, metal contamination, etc ) pollutants Active and abandoned surface and underground mines, mineral processing plants, mine and processing plant waste disposal areas, haulage roads, and tailing ponds are typical sources of mine related water pollution (130) One of the most serious pollution problems arising from mining activities is acid mine drainage resulting from the chemical reaction of sulfide minerals (commonly iron sulfides) and air in the presence of water Acid mine drainage is commonly associated with coal and hard rock mining areas in the United States In general the more serious and extensive acid mine drainage problems exist in the more humid coal regions east of the Mississippi River (11) In 1964 the U S Department of the Interior, Fish and Wildlife Service, reported that acid mine drainage adversely affected fish and wildlife habitat in 9,477 kilometers (5,890 miles) of streams and 6,062 hectares (14,967 acres) of impoundments in 20 states in the United States (64) Of the total affected waters, coal mining operations accounted for 97 percent of the acid mine drainage pollution reported for streams and 93 percent of that reported for impoundments In 1970 more than 19,308 kilometers (12,000 miles) of streams in the United States were reportedly significantly degraded by mining related pollution (130) Of the total affected kilometers, 16,920 kilometers (10,516 miles) or approximately 88 percent were located in the Appalachian coal region (Pennsylvania, West Virginia, Ohio, eastern Kentucky, Tennessee, Maryland, and Alabama) In addition, more than 965 kilometers (600 miles) of streams reportedly were degraded by coal mining in states in the Illinois, Western Interior, and Rocky Mountain coal regions The remaining portion of the stream pollution resulted from the mining of (1) copper (california, Montana, Nevada, New Hampshire, Tennessee, Virginia, and Wyoming), (2) lead and zinc (Colorado, Idaho, Kansas, Missouri, Montana, Oklahoma, and Tennessee), (3) uranium (Rocky Mountain States), (4) iron (Lake Superior iron region), (5) sand and gravel (all states), (6) phosphate (Florida and other states), (7) gold (Alaska), (8) bauxite and barite (Arkansas), and (9) molybdenum, gold, and other metals (Colorado) Abandoned mines and abandoned mine waste disposal areas contribute a large portion of the total pollution resulting from mining activities Numerous abandoned underground mines are located throughout the United States and many are discharging mine drainage pollutants In 1966 the U S Bureau of Mines estimated that more than 88,000 inactive and abandoned underground mines were in existance (126) A listing of these mines by state is presented in Table 1 0-1 More recent estimates indicate that this list is incomplete In Colorado alone there is

Jan 1, 1975

By Wesley A. Grosh

The Vest nickel prospect, in Floyd County, Va., was discovered about 25 years ago. Limited exploration of the deposit had indicated some appreciable nickel mineralization in the sulfide ore. The property was examined on March 9, 1943, by an engineer of the Bureau of Mines in company with C. W. Vest, owner of the property. A limited exploration program was recommended. Two holes totaling 320 feet were diamond-drilled in January 1944. Drilling indicated the sulfides are sparsely disseminated. The only nickel values of interest were at the old prospect shaft.

Jan 1, 1949

By Henry Kreisinger, John Blizard

This preliminary statement presents some of the results of tests carried out at the Lakeside Station of the Milwaukee Electric Railway and Light Co. , by the fuel section of the U. S. Bureau of Mines , in cooperation with the research department of the Combustion Engineering Corporation of New York . The object of these tests was to determine the thermal efficiency , ease of operation , and other particulars of a boiler equipped with specially designed furnace and burners for burning powdered coal . The boiler tested haş 13380 square feet of heating surface , and is one of eight boilers equipped with the Lopulco powdered coal system supplying steam to two 20,000 -Kw . steam turbines in the largest power house burning powdered coal . Twenty- six tests were run at rates of heat transference varying from 4000 to 8000 B.t.u. per square foot of boiler heating surface , and the mean thermal efficiency attained was about 84 per cent , based on the gross calorific value of the fuel as fired . The efficiency varied little with the rate of steaming , and its high value is accounted for by the small loss from incomplete combustion and the small amount of excess air which varied from 5 to 36 per cent . The coal burned had a gross calorific value of about 11500 to 12800 B.t.u. per pound , contained 2 to 5 per cent moisture , 33 to 36 per cent volatile matter and 9 to 13 per cent ash, and was so ground thaf 89 to 95 per cent would pass through a 100- mesh sieve . The ash had a softening point of 2150 to 2450 degrees F. , but did not fuse together at the bottom of the furnace because it was partly protected from the flame radiation by means of a series of water tubes connected to the boiler which were placed between the fumace bottom and the flame, ..

Jan 1, 1923

By McHenry Mosier

A skull breaker has demonstrated its advantages for secondary breaking in a limestone quarry by entirely displacing secondary blasting . It has reduced safety hazards to workmen, increased the number of quarry operating days , and has lowered mining costs by 2.7 cents a ton. It is believed that the application of the skull breaker can be made economically advantageous in the surface mining of other commoditics .

Aug 1, 1948

By M. J. Reasor, J. M. Antonini, L. Wu, K. Van Dyke, Z. Ye

The inhalation of silica has been shown to produce a dramatic inflammatory and toxic response within the lungs of humans and· laboratory animals. Currently, no effective treatment exists for workers who may have been exposed to the inhalation of silica. The objective of this study was to develop an animal model in which we could evaluate the effect that anti-inflammatory steroids have on the acute silica-induced pulmonary inflammatory response. Male Fischer 344 rats were pretreated with either dexamethasone (2 mg/kg) or saline vehicle (i.p.) on days 1, 3, and 5. On day 6, the animals from the two groups were then intratracheally instilled with either silica (20 mg/0.5 ml saline vehicle) or saline vehicle (0.5 ml). Twenty-four hours after the instillations in the non-steroid group, significant increases occurred in total protein, total number of cells, neutrophils, and lymphocytes recovered from the lungs of animals treated with silica compared to saline controls. Silica also caused dramatic increases in the luminol-dependent chemiluminescence (LDCL) of lung tissue and bronchoalveolar lavage (BAL) cells. The LDCL reaction was markedly decreased by either superoxide dismutase (SOD) or N-nitro-L-arginine methyl ester hydrochloride (L-NAME). SOD is involved in the enzymatic breakdown of superoxide anion, while L-NAME, a nitric oxide (NO) synthase inhibitor, prevents the formation of NO. When the superoxide anion and NO react, they form the highly oxidizing substance peroxynitrite. This study then implicates peroxynitrite as an agent which may be involved in the silica-induced oxidant lung injury. When the animals were pretreated with the steroid dexamethasone, there was a complete protection against the biochemical, cellular, and chemiluminescent indices of damage caused by silica. The mechanism in which the steroid protects the lung from damage may be due to the ability of dexamethasone to block the induction of NO synthase. With further study in animals, the anti-inflammatory steroids may be useful in the treatment of silicainduced lung injury.

Dec 1, 1995

By Raymond B. Ladoo

SOAPSTONE

Feb 1, 1922

By M. H. Rinkenbach, C. A. Taylor

The detonating compound cyanuric triazide was discovered*** and patented**** by Erwin Ott, and on account of his claims, the Bureau of Ordnance, U. S. Navy, desired more complete data, so an investigation was made. The results obtained were such that the Bureau of Crdnance recommended publication thereof for the benefit of the explosives industry. Some of the patent claims regarding cyanuric triazide are as follows: 1. It is not poisonous in contradistinction to fulminating mercury and lead azide. 2. In contradistinction to the hitherto employed priming agents it is fusible, and its fusion point (94°C) is so low that the product melted by a single heating in water or steam bath, can be poured without danger in the capsule shell. It solidifies therein after cooling, and shows the density of 1.5. 3. It has been determined that the cyanuric triazide, in spite of its very much higher priming actions, is much less brisent then ful- minating mercury and lead nitride. 4. The chemically pure cyanuric triazide (C3M2) constitutes colorless crystals melting at 94°0., and is not volatile. It is not affected by cold water, and only slowly saponified by hot water. It is relatively insensitive to friction and not too strong concussion, but explodes by impact or when hea ted to 170°C., or when heated suddenly. It is not more sensitive to friction and shocks then fulminating mercury. 5. The preparation of the triazide is preferably carried out by acting with an excess of sodium azide in an aqueous solution; in the cold, on cyamric chloride gradually suspended in the said solution.

Aug 1, 1923

By R. Karl Zipf, Z. T. Bieniawski

"A set of fracture profile photomicrographs is presented for fractures generated under mixed mode loading of the Pittsburgh coal. The fractal dimension is used· to characterize the irregularity of these profiles and a tentative relationship is presented between the fractal dimension and the fracture toughness. Surface roughness appears to depend solely on the stress intensity and no other dependence was observed with fracture loading mode, loading rate· or specimen orientation. Observations of crack bifurcations.in fracture profiles can indicate crack growth direction whereas direct surface observations generally cannot in materials such as rock and coal.1 INTRODUCTIONThe production of fine fragments of material as a result of some loading event occurs in many industrial processes. In crushing and grinding, the efficient production of fine fragments is the desired end result; .however, in coal cutting, the production of fine fragments may lead to high levels of respirable dust in the immediate atmosphere with the danger of human lung diseases. Two of the most important sources of fragments in the 1 to 10 micron size range during a cutting process are 1) severe crushing in a zone near the loading tool and 2) subsequent shearing along major crack surfaces that form the larger fragments during material reduction. These and other sources of fine fragments generation are discussed by Roepke (1984) and Zipf and Bieniawski (1986). The physical character of the nearly created major crack surfaces is believed to have a strong influence on the amount of fine fragment generation that occurs during subsequent shearing movement. When the major large fragments initially form, they are ""locked"" in place by the irregular character of the new fracture surface. Only after some relative motion has occurred between fragments are they actually liberated, and the net result is the formation of additional fine fragments. The fine fragmentation is not necessarily limited to the shearing of high points from the macrocrack surf ace since material remaining in the wake of the crack tip is damaged to a substantial depth below the actual crack surface."

Aug 31, 1989

By Frank J. Cservenyak

Curtailment of bauxite importation by enemy activities during World War II focused attention on the necessity of developing domestic deposits of aluminous materials. Large quantities of aluminum ores such as kaolin, siliceous bauxites, high-iron bauxites, anorthosite, and diaspore clays are available but not readily amenable to Bayer processing because of excessive impurities. The Bayer process, which is the only commercial method in use in the United States for producing metallurgical-grade alumina, requires a high Al2O3 bauxite relatively low in SiO2 and Fe2O3. The Bureau of Mines was charged by Congress to investigate processes for the production of alumina from these low-grade ores. One part of the program was an investigation, in the laboratory and pilot plant, of the recovery of alumina by the lime-soda sinter process. Ores comprising kaolin, diasporic clays, anorthosite, and siliceous bauxites have been investigated and studied in the laboratory and pilot plant, and a series &apos;of reports covering these investigations has been prepared.

Jan 1, 1948