Search Documents

By W. M. Weigel

"The use of sand for the filtration of municipal water supplies is comparatively recent use in this country, although at the present time, most cities of any size that draw their water supply from surface sources use sand filters in their purification system. Not only are sand filters employed to remove sediment and suspended matter, but they also take out most of the bacteria in the water.The first comprehensive research and study of sand for this purpose was probably that of Hazen for the Massachusetts Board of Health in 1891 and 1892, although sand filters had been employed for a considerable time before, specifications for filter sand drawn since then have been largely based on the results of Hazen's work,The general requirements for filter sand are more exacting than for any of the different kinds of sands, except the chemical specifications for glass sand. Filter sand must be uniform in size and within certain limiting sizes. In addition, it must be clean and free from clay and organic matter and of fairly high purity. Early investigations established the fact that an excess of fine materiel increased the friction and decreased the rate of flow through the filter, and that the size of the finer particles rather than the courser, determined the effective size. Also, that large grains tended to cause irregularities in flow in different parts of the bed. There is no requirement as to grain shapes, except that they be not flat or elongated, since, so far as known, either rounded or angular grains are equally efficient.Based on Hazen's investigations, two factors are quite generally used to control the average size and uniformity of size of the sand. These are defined as follows: The ""effective size"" of a sand is such that 10 per cent by weight of the seed is finer than this size, end 90 per cent is coarser. It is expressed in millimeters, The ""uniformity coefficient"" is defined as the ratio of the size of grain which has 60 per cent finer than this size to the size which has 10 per cent finer (the ""effective size""). It is evident that the smaller this coefficient, the more uniform is the seed. If all the grains were exactly the same size, the coefficient would be 1."

Jul 1, 1924

By D. R. Dolinar, J. Pablic, D. C. Oyler, T. P. Mucho

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the 'advance and relieve method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

By Charles L. Kimbell

Some comment on data availability must be an integral part of a study such as this. For many years, the centrally planned economy nations of the world regarded as state secrets much of their mineral commodity production information, as well as a considerable body of the foreign trade information on these commodities, and virtually all reporting on their consumption. Within the past 5 years, this pattern has undergone some evolution, and although these countries still fall short of market economy countries in their willingness to publish, there has been measurable improvement. Fit, China, and then subsequently the former CMEA member countries of Eastern Europe have released in print an increasing amount of information in organized, coherent formats, although in a number of cases it is not clear that the information provided is in perfect definitional accord with market economy country practices. Thus, these recently available statistics must be carefully studied to ensure that they are provided in terms of conventional market economy definitions. At the same time that heretofore unpublished information is becoming available for the centrally planned (or formally centrally planned) economy countries, there has been a slow but steady disquieting erosion of availability of production, trade, and consumption data for market economy countries. There are evident reasons for some of these losses in information. The foremost of these relates to corporate mergers. As the number of producing or consuming firms of a given commodity in a given political jurisdiction declines, it is increasingly difficult for government agencies to protect proprietary company data. In past years, this protection was afforded by aggregating data for the several companies operating in the area, but as the number of operators diminishes this is no longer always possible. Hopefully, given this situation, companies will at least authorize release of data after a period of time, when its publication will not provide competitors with unfair access, but will make possible longer term studies.

Jan 1, 1992

By Margaret M. Ragin

In a cooperative effort between the U.S. Bureau of Mines and the Florida Institute of Phosphate Research, with input from the phosphate industry, the conversion of phosphogypsum to sulfur has been investigated. The first step in the conversion scheme involves reduction of phosphogypsum to calcium sulfide. Effects of temperature, catalyst, reaction time, and type of reductant (carbon monoxide and coal) are discussed. It was determined that phosphogypsum could be reduced to calcium sulfide at 850° to 1,000° C using either coal or carbon monoxide as the reductant. The required temperature was lowered to 750° C using ferric oxide or magnetite as a catalyst for the reduction reaction. Results indicate that as the volatiles content of the coal is increased, reaction temperature may be decreased to obtain a given conversion, or if the reaction temperature is maintained constant, the conversion can be increased. Best results were 95- to 100-pct conversion using a high-volatile coal at 800° to 850° C. Addition of a catalyst increased calcium sulfide yield when low- or medium-volatile coals were used as reductants, but had little effect when high-volatile coals were used.

Jan 1, 1990

By Kenneth J. Miner

Pittsburgh bed and Lower Freeport bed coals were tested in the U.S. Bureau of Mines two-stage froth flotation pilot plant, which utilizes a new flotation process to remove pyritic sulfur. The process consists of a first-stage coal flotation step to remove coarse, free pyrite and other refuse in the tailings. The clean coal froth concentrate is then repulped and treated with a coal depressant, a pyrite collector, and a frother to selectively float the remaining pyrite in a second stage. Results in the pilot plant were excellent, comparing well with those obtained in laboratory batch tests. That is, about 70 percent of the pyrite present in the Pittsburgh bed coal and about 90 percent of the pyrite present in the Lower Freeport bed coal were removed with excellent final clean coal recoveries.

Jan 1, 1973

By D. E. Hirsch

The Bureau of Mines has developed a systematic procedure for separation, characterization, and semiquantitative analysis of high-boiling (350° to 550° C) distillates of crude oils. Isothermal and molecular distillation were used to prepare the 370° to 530° C distillate of Recluse, Wyo., crude oil. The distillate was separated into fractions by chemical treatment, silica-alumina gel adsorption, and gel permeation chromatography (GPC). The fractions were analyzed by use of GPC correlations and mass and nuclear magnetic resonance (NMR) spectrometry. The increased knowledge of petroleum composition obtained from the data will contribute to improved petroleum processing and utilization and energy conservation.

Jan 1, 1974

The initial results from the magnetic sludge factorial experiment are summarized in Table 2. For ease in interpretation, the four separate variables are identified with the high and low level of each variable being represented by + and - signs, respectively. Several important relationships are evident from an inspection of the data in Table 2. For example, magnetic sludges were obtained only during the high temperature tests. Secondly, with the exception of the last three tests, there is an apparent correlation between settled sludge volume (or sludge settling rate) and pH. Data on residual dissolved Fee+ indicate that precipitation of iron is not complete at pH 8 and room temperature (Tests l, 3, 5, and 7). Although this should not have any confounding effect on the interpretation of the results, it is an important observation and an aspect of the overall conceptual process that should be considered carefully during any future developmental work. The data in Table 2 were employed more fully in the calculation of main effects and variable interactions for each of the three responses. For this purpose, a codified design and calculation matrix, shown in Table 3, was used. The derivation of this matrix is described by Davies.(9) The positive or negative signs for variable interactions are obtained simply by algebraic multiplication of the signs for each single variable involved in the interaction. Main effects and interactions are calculated by multiplying the response values (Table 2) by the corresponding effect elements (Table 3), summing the results, and dividing by 8. The resulting value for single variables is also sometimes designated as an average effect, since (for tyro levels of the variable only) it is simply the difference between the average response of all trials carried out at the first level of the variable (factor) and that of all trials at the second level. If the effect of one variable changes at different levels of another variable, the two variables are said to interact. The relative importance of the variable or variables in question is reflected by the absolute magnitude of the calculated main effect or interaction. First-order (two variable) interactions are usually easy to interpret in terms of the physical behavior of the system. Second- and higher-order interactions are often less readily understood, and are often of minor significance in any case. The main effects and interactions derived from the present study in the manner described above are listed in Table 4. It should be noted that

Jan 1, 1971

By P. R. Tisot

The structural response of propped oil shale fractures was determined for each of two different grades of Green River oil shales (38.0 and 29.0 gpt) as they were heated in an inert atmosphere from ambient to subretorting temperatures (below those required for rapid pyrolysis of the organic matter). Small oil shale cores were propped apart by 3-mm glass beads to simulate a small cross section of a propped oil shale fracture between an injection and a producing well. These specimens were then heated at a uniform bate up to 800° F in a specially designed test cell under stress levels from 100 to 1,000 psi in biaxial and in triaxial confinement. Under the conditions of heat and compressive stress utilized in this study, all of the propped fractures in the two oil shales underwent structural deformation ranging from partial to complete collapse, as evidenced by proppant embedment. Structural collapse of induced fractures would in turn result in serious impairment or complete loss of the fracture flow capacities of the specimens. Results from this Bureau of Mines study indicate that underground retorting of Green River oil shale may be seriously impaired by loss of permeability when utilizing propped fractures in oil shales assaying more than 28 gpt.

Jan 1, 1975

This part of the final report treats some problems related to coal mine carrier frequency communication systems using the trolley wire/track transmission line. This work was undertaken for a brief period of time during the summer of 1972 to help understand, quantify, and improve some of the trolley wire carrier system behavior observed and/or predicted. Calculations and estimates of transmission line characteristic impedance, inductance and capacitance per unit length, mine motor loading effects, parallel line effects, and connection impedances are presented in Chapter I. Chapter II treats the design of r-f isolators for reducing the undesired and troublesome r-f loading that mine motors present to the trolley transmission line. Chapter III treats a diversity method for combatting standing wave nulls. I. CALCULATIONS RELATED TO TROLLEY WIRE COMMUNICATIONS A. ESTIMATION OF INDUCTANCE AND CAPACITANCE PER UNIT LENGTH OF TROLLEY LINES To estimate the L and C per unit length of trolley lines, we use the eccentric line model of Section G of this Chapter, "Characteristic Imped¬ance Estimates for Mine Trolley Lines." The capacitance per unit length for an eccentric line is given by (1)

Jan 1, 1974

By I. D. Shah

The copper-nickel ore of the Duluth Gabbro Complex in northeastern Minnesota is a large potential domestic resource of cobalt and platinum-group metals. However, because of the low grade of the primary metal values (0.5 pct Cu, 0.15 pct Ni), the private sector has assigned a relatively low priority to the development of technology for processing this ore, anticipating that mining probably would not begin until the mid-1990's. Furthermore, preliminary processing flowsheets considered by the mining companies centered on the primary metal values. As part of an effort to help provide the basis for technology to recover critical and strategic minerals from domestic resources the Bureau of Mines is investigating methods to recover all of the mineral values, in the Duluth Gabbro material, with particular attention to the byproduct critical minerals. A key step in this process is the removal of a relatively large amount of iron present in the bulk sulfide flotation concentrate to permit subsequent extraction of mineral values. This report describes a direct smelting method that removes most of the iron and produces a copper-nickel-cobalt matte, an intermediate product from which the metal values subsequently are separated. Copper, nickel, and cobalt grade and recovery data are presented for the direct smelting method. Test results showed that under certain conditions some of the mineral values reported to the slag, requiring slag cleaning to recover them.

Jan 1, 1983

Reduce worker exposure to respirable dust without interfering with bag-filling operations. Approach A dust control hood was developed which contains and captures dust close to its source and prevents it from entering the bag-filling operator's work place. How It Works A sheet metal hood is placed around the nozzle of the bag filling machine. The hood is connected through ducts to the plant exhaust ventilation system. Air pulled into the front of the hood and around the sides of the bag picks up dust generated inside the hood, and carries it to the dust collector. The size of the hood can be adapted to fit most fluidized valve-type bag-filling machines. The height of the hood depends on the bulk density of the product and weight of the bags being filled. The 14-inch-width of the hood allows it to be used on multi-nozzle baging machines spaced 16 inches on center. Only 2/3 of the bag is actually within the hood, and this allows easy operator access for placing the bags on the nozzle.

Jan 1, 1978

By Andrew D. O. O’Brien, Linda J. McWilliams, Joe L. Howell, Douglas E. Pollock, Jeanne A. Zimmer, Andrew B. Cecala

A quick, safe, and effective method has been developed that allows workers to clean their dust laden work clothing periodically throughout the day. For the mining industry, this technique is much more effective than the current federally approved method of using a vacuuming system. This newly designed method is relatively inexpensive and can be easily installed at any operation to allow workers to clean their clothing without contaminating the worker, the work environment. or co-workers to elevated respirable dust levels. This clothes cleaning process uses an air spray manifold to blow dust from a worker's clothing in an enclosed booth, which combines the dust for capture and removal by a baghouse dust collector. Since the air exhausted by the dust collector causes the booth to be under negative pressure. no measurable quantities of dust were ever measure escaping from the booth to contaminate the work environment and/or other workers. The worker performing the cleaning process is required to wear a half-mask fit- tested respirator with an N 100 filter, hearing protection, and full seal goggles. Dust samples taken inside the respirator of test personnel performing the clothes cleaning process showed very minimal to no respirable dust. This clothes cleaning process was performed in less than 20 seconds and was significantly y cleaner than either the Federally approved method of vacuuming, or the most common method or using a single compressed air hose. It was also determined during this research that polyester-cotton blend coveralls clean more effectively than coveralls which are 100 percent cotton. The newly designed clothes cleaning process has potential application to any industry where workers' clothing becomes contaminated with most any type of dust or product.

By Dean E. Bluman

The Bureau of Mines investigated the convective heat transfer coefficients for recirculated suspensions of 30-micron glass beads in inert gas. Coefficients for the suspensions were not significantly higher than coefficients for the pure gas. Reynolds numbers of the suspensions were 20,000 to 35,000; solids loadings ranged from 0.0 to 0.7 pound per pound of gas. Comparison of the results with published data showed the direction of heat flow to have no effect at the test conditions.

Jan 1, 1967

By G. M. Potter, F. S. Wartman, M. D. Schmid

"In matte smelting of copper it has been established that the sulphpr present will combine with copper as long as the latter is present, and that thereafter it will combine with iron. The Cu-Fe ratio in the matte is determined by the Cu-S ratio, presumably owing to the much greater affinity of copper for sulphur or, expressed thermodynamically, the greater stability of copper sulphide in contact with silicate slag. Now, the work of Fournet and of Schütz, which is quoted in many elementary metallurgical texts, indicates that manganese ranks ahead of copper in its affinity for sulphur. Hence, we might expect that manganese could be concentrated from its admixture with iron. Compounds by matte smelting, and Rotts / has patented such a process. This greater affinity of manganese or sulphur is used to advantage in iron metallurgy, also, in which it is well-known that sulphur will combine with manganese and separate from metallic iron as manganese sulphide. Manganese sulphide,however, is quite soluble in silicate slags. 5/ The loss of manganese in slag in any attempted matte smelting is therefore great.If this solubility of manganese sulphide is slag is a physical one and the reaction MnO + FeS MnS + FeOIs substantially complete, then it might be expected that the addition of copper sulphide, which is almost entirety insoluble in slag, would serve to extract the manganese sulphide with the formation of a manganese-copper matte on the other hand, if an equilibrium exists in the above reaction, a copper sulphide layer would displace that equilibrium in one direction or the other, according to whether iron sulphide or manganese sulphide were more soluble in the matter layer."

May 1, 1937

By R. K. Koch

The vapor pressures of liquid columbium and liquid hafnium were deter-mined by the Langmuir free evaporation method as a part of the Bureau of Mines program on the study of transition metals. An electron-beam furnace with a water-cooled copper crucible was used for melting. Temperature was measured with a two-color ratio pyrometer. Least-squares analyses of the vapor pres-sure data gave the following equations: [Logp (atm) = 5 .429 -31,310 T] for liquid columbium in the range 2,740° - 3,140° K, and [Log p (atm) = 5,690 28 T] for liquid zirconium in the range 2,500° -2,810° K. Third-law evaluations of each data set gave mean heats of sublimation (298.15° K) of 175.1±3.2 kcal/mole and 148.3±1.2 kcal/mole for columbium and hafnium, respectively. Second-law standard heats of sublimation determined from sigma plots and from sigma-prime plots agreed fairly well with the third-law values. The sigma-prime plots gave standard entropies of sublimation of 30.96±0.84 eu and 33.S6±0.44 eu for columbium and hafnium, respectively.

Jan 1, 1968

In 2004, a total of 4,401 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). Stone mines comprised 30.4% of all mining operations.

Sep 1, 2007

By T. M. Nasiatka

This report sterns from a study undertaken by the Federal Bureau of Mines to determine the possibility of reducing filter-cake moisture by applying radiant heat. Suitable laboratory equipment was set up to study the effect of heat, heating time, proximity of the heater to the filter cake, cake thickness, and other variables related to the final filter-cake moisture. A minus-48-mesh coal slurry and application of heat for 60 seconds resulted in filter-cake moistures 5.6 to 13.2 percentage points lower than could be accomplished by filtration alone at 24 inches of Hg for 1-1/4-and 1 1/2-inch cake thickness, respectively. The moisture reduction can be attributed to the combined effect of lower fluid viscosity and evaporation.

Jan 1, 1959

By Yael Miron

Coal mines that undergo self-heatings, and specifically mines that sustain both floor heave and self-heatings, would benefit from the use of sealants to minimize air ingress to susceptible areas. The U.S. Bureau of Mines(USBM) evaluated three sealant systems for this purpose, bentonite-water mixtures, silicate gel, and guar gum gel. The guar gum-based gel was the only sealant that possessed the desired properties of elasticity, ease of preparation, adaptability to the mine, and a long life. In addition, since the gel consists mostly of water, it could quench or cool nearby heatings. Optimal formulations were determined in laboratory tests, and then tested in the USBM Safety Research Coal Mine. Two formulations resulted in stable gels that lasted for at least 12 months in the mine. Semi continuous preparation of gel using an eductor was evaluated and appears feasible. Although guar gum gel is expensive, selective use to prevent heatings in specific areas would be cost-effective, both interms of productivity and enhanced mine safety.

Jan 1, 1995

By R. W. Stahl, H. E. Sanford, J. B. Benson

"As movement or transportation of coal is second only in importance to actual mining, and as the latter is wholly dependent on the former, the efficiency of the haulage system often determines the efficiency of the entire plant. Safe or accident-free transportation is essential, also, because no attempt is made to divorce safety and efficiency, it being realized that they are inseparable.Most of the Ruhr mines were opened decades ago, and many features that were considered up-to-date then are now obsolete. Progress in developing haulage systems has been slow, chiefly because it would be very costly to change many to accomodate more modern equipment. These systems are being altered or modernized slowly, as capital permits. The only revolutionary changes that have been made in mine haulage are the use of larger locomo¬tives and cars, in the movement of shuttle cars, and in the adoption of skip hoisting. Most Ruhr shafts, however, will not accomodate large cars, the secondary roadways are too narrow for large locomotives, and the coal is too soft to permit skip hoisting because degradation would be too great. Therefore, notable advances have been made only at newer plants, where allowances have been made for modern equipment.The shafts are deep (average 2,300 feet) and of comparatively small diameter. The small bore was designed to reduce costs of sinking and lining. Generally, the shafts are lined throughout with masonry; however, most of the buntons and guides are wooden.The hoisting engines arc installed in masonry structures, and where more than one hoist is used they are placed on opposite sides of the shaft to eliminate as much noise as possible (fig. 1). This arrangement also prevents an engineer from acting on any signals except those transmitted to him. A few hoisting engines are mounted in the headframes (fig. 2). The hoisting engines are equipped with overwind, overspeed, and auxiliary braking devices, which are tested frequently and kept operative at all times. The signal code is displayed in view of the engineer, and a light or dial indicator informs him of the cage's position in the shaft. Many hoists are equipped with re¬cording devices, which show on a continuous chart the speed of hoisting as well as any delays throughout the 24-hour period.A Koepe system of winding is in general use because of the depth of shafts (fig. 3). With this system, a single rope passes over a single-groove, large-diameter sheave attached to the motive power, and the ends of the rope, after passing over the head sheaves, are attached to the cages. A flat tail rope suspended in the shaft and connected to the bottom of the cages serves to balance the system. Both steam and electric engines are used to activate the hoisting system, end the engines are capable of moving at least a 50-percent overload.The ropes are necessarily of large diameter (2-1/2 inches and greater), and flexibility decreases as rope diameter increases. To overcome the unwieldiness .of large-diameter ropes as shafts become deeper, a four-rope system is being tried at one mine (fig.4). In this system the load is equalized between four ropes which permits much smaller ropes to be used. All hoist ropes are inspected daily and discarded after 2 years service unless special permission for longer service is granted by the Mine Inspectorate, and then only after thorough visual and electromagnetic inspection."

Jan 1, 1950

By Dennis R. Dolinar, Lewis A. Martin

Cable bolt technology used by the U.S. coal industry was developed to a large extent in the 1990s. Today, these cable systems include both cable bolts and cable trusses to provide supplemental and secondary support in gate roads. This cable technology is significantly different than the cable systems in use in either U.S. hard-rock mines or Australian coal mines. Development of this technology was initiated and spurred by research efforts of the U.S. Bureau of Mines, and has continued under the health and safety programs of the National Institute for Occupational Safety and Health (NIOSH). It was also followed up by work of roof support manufacturers to create an essentially new support system. In this paper, the important support characteristics of both cable bolts and cable trusses are discussed. The design of cable systems and the basis for that design for tailgate and headgate situations are reviewed and explained. Case histories are presented on the application of these support systems based on experience gained at a number of in situ test sites.

Jan 10, 2000