Search Documents

By Paul R. Amyotte, Omotayo Kalejaiye, Kenneth L. Cashdollar, Michael J. Pegg

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRI, 20-L and Fike 1 -m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1 -m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

By Keith L. Harris

Real gross national product3 (GNP) grew at a seasonally adjusted annual rate of 4.2% in the fourth quarter compared with a revised 4.3% rate in the third quarter, according to the most recent estimates released by the U.S. Department of Commerce (table 1). Expanding inventories, Government purchases of goods and services, residential fixed investment, and a narrowing of the trade deficit fueled the growth. Significantly reduced consumer demand led to the heavy inventory growth. Almost half of the buildup in inventories consisted of automobiles because consumers reduced purchases when Detroit ceased most incentive programs in late summer. Reduced consumer demand also affected imports, however, and the narrowing of the trade deficit resumed after widening in the third quarter. Nonresi- [ ] dential fixed investment also declined after a strong gain in the third quarter. On a year-to-year basis, the economy grew at an inflation-adjusted rate of 2.9%, the same as that of 1986. However, on a fourth-quarter-to-fourth-quarter basis, the real growth reached 3.8%, the highest growth since 19M, and exceeded the Reagan Administration's estimate of 3.4%. Rising merchandise exports accounted for about one-third of the growth in GNP for all of 1987 and are expected to continue to grow as domestic manufactures benefit from the lower value of the dollar vis-a-vis other major trading country currencies. Consumer demand became a less important factor of economic growth, but employment continued to grow (table 2), and civilian unemployment declined by 0.9 percentage points (December to December) as the industrial sector geared up to increase exports. Inflation, as measured by the fixed-weighted GNP price index, remained low at 3.4%.

Jan 1, 1988

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Ti and Zn-1.0 wt pct Cu-Ti alloys containing up to 0.36 wt pct Ti. Finish rolling was at varied temperatures to total reductions as high as 92 pct. Alloy properties are very sensitive to various combinations of composition, rolling temperature, and reduction. Properly rolled Zn-1.0 Cu-Ti alloys are superior in strength to Zn-Ti alloys. Conditions are described that lead to best tensile properties. Creep resistance for Zn-Ti alloys decreases with increased rolling temperature when finish rolled to 92-pct total reduction: but not when finish rolled to 33- or 67-pct reduction. Creep resistance for 7n-1.0 Cu-Ti alloys improves with increased rolling temperature to about 480° F. Heavily cold-rolled Zn-1.0 Cu-Ti alloys have fine grain sizes and poor hardness, tensile, and creep properties, but high ductility. Thermal expansivity is markedly affected by the copper addition. Data show the anisotropy of tensile, creep, and thermal expansivity properties. Large idiomorphic crystallites of TiZn15 appear in both Zn-Ti and Zn-Cu-Ti alloys when more than about 0.2 pct Ti is present. A new Zn-Cu-Ti intermediate phase was also identified. Empirical equations are presented relating creep rates with major process variables.

Jan 1, 1971

By W. E. Wallace

Volume-rate-of-flow measurements were made of the flow of mercury through porous samples under conditions of no field, magnetic field transverse to the direction of flow, and transverse magnetic field and electric current to determine if a magnetic method might be potentially useful in the study of pore-size distribution. No change was observed in the flow rate from the application of a magnetic field alone. The application of both field and current produced an electromagnetic pumping action with or against the direction of flow, depending upon the direction of the electric current. This pumping effect was observed to be greater in a rectangular porcelain sample than the calculated value for an equal-Sized open channel.

Jan 1, 1969

By Robert K. Koch, Henry E. Blake

Laboratory tests were made to determine if aluminum fluoride of commercial grade could be synthesized by reacting alumina hydrate with dilute ( 25 to 75 grams per liter of fluorine ) aqueous fluoride solutions . • Products containing up to 90 percent aluminum fluoride ( A1F ) were synthesized by reaction of alumina trihydrate ( A120 3H2O) with either dilute hydrofluoric acid ( HF ) or ammonium fluoride ( NHF) solutions , the ammonium fluoride solution resulting from ammonia ( NH ) desilication of a hydrofluoricfluosilicic acid ( HF - H₂ SiF ) solution . Fluorine recoveries of over 80 percent were obtained with either type of solution . The hydrated precipitates of AlF, and ( NH4 ) , A1F ( ammonium aluminum fluoride ) obtained by reacting hydrated alumina with these solutions were subsequently converted to anhydrous AlF, by controlled heating .

Jan 1, 1964

By Jeffery L. Kohler, Harvinder Singh, Jon G. Bredeson

A survey of electromagnetic noise reports was performed and a summary of the results are given. Industrial concerns were surveyed for techniques to minimize the effects of electromagnetic noise and are presented. The common types of communication links used in mines today are presented. A mathematical development was presented which determines the probability of bit errors versus distance for various types of communication links designed for in mine use. The probability of undetected errors for the protocols of the communication links is given together with burst error detection.

Jan 2, 1981

By Robert K. Koch

Laboratory-scale studies on defluorination of natural and synthetic fluorspars by pyrohydrolysis at 1,500° C. were made to determine the feasibility of developing a process for producing hydrogen fluoride from siliceous fluorspars. It was found that the reaction (at 1,500° C.) is not promising for process development, even though a silica-free offgas can be generated. The primary difficulty is the low hydrogen fluoride content of the offgases; an HF content of 6 percent was the best achieved. Previous research by the Bureau of Mines has demonstrated that offgases averaging 27 percent hydrogen fluoride can be produced under carefully controlled conditions at 1,280° C. The lower temperature process is a better method for production of HF. However, charges in which the CaF to Si02 mole ratio varied from 0.4 to 2 could be processed with similar results. Also, combined alumina and ferric oxide contents up to 25 mole-percent did not noticeably alter the rate of defluorination. Therefore, virtually any natural siliceous fluorspar would respond in essentially the same manner when exposed to water vapor at 1,500° C.

Jan 1, 1962

By D. N. Nilsen

The Bureau of Mines is investigating a method to recover Ni, Cu, and Co from low-grade domestic laterites through reduction roasting, leaching, sol-vent extraction, and electrowinning unit operations. The objective of this research is to develop processing technology that can convert low-grade domestic deposits containing critical metals into national reserves. As a part of this research, a solvent extraction system was investigated for the extraction of nickel and copper, followed by the separation and production of suitable electrolytes. Nickel and copper were coextracted from ammoniacal ammonium sulfate leach liquors (pH~9.5) with LIX 64N extractant in a laboratory-size mixer-settler continuous circuit. Three extraction stages resulted in >99-pct extraction of nickel, substantial copper extraction, and essentially no cobalt extraction from leach liquors. A crowd stage reduced the ammonia loading on the solvent by maximizing nickel loading. Residual ammonia was removed from the loaded solvent with a pH-controlled scrub. Nickel and copper loaded on the solvent were separated by selective stripping. Typical nickel strip circuit operation using electrolyte containing 90 grams per liter (g/l) Ni and 11.9 g/l H2S04 yielded >99.9 pct Ni stripped from the solvent in five stages. The copper loading on the recycled solvent was controlled in a copper strip stage using electrolyte containing 25 g/l Cu and 160 g/l H2S04,

Jan 1, 1981

By H. E. Peterson

This report revises an earlier publication by the Bureau of Mines on tungsten analytical procedures and expands the coverage by including appropriate procedures for the critical impurity elements that commonly occur in tungsten ores and concentrates (13).3 The basic methods described are not original, but many of the modifications to improve reliability and sensitivity were developed by the Bureau. Gravimetric and colorimetric methods currently used for the determination of tungsten in ores, mill tailings, and concentrates are described. Colorimetric procedures are preferred for low concentrations of tungsten, whereas either procedure is satisfactory for moderate concentrations. Conversely, a gravimetric method is preferred for the determination of tungsten in concentrates.

Jan 1, 1963

By T. A. Kubala

Electric discharge ignition has been reinvestigated in a modified Hartmann apparatus for lycopodium powder with air. Minimum stored energy to ignite air dispersions of lycopodium was 25 to 30 mj; ignition occurred with 1 gram of lycopodium dispersed into the 2.7-liter vessel. Ignition energy was measured as a function of the weight of powder used, although some reservations are expressed concerning the uniformity of the lycopodium-air mixtures. In particular, wall layers of lycopodium, remaining after dispersal of 1 gram of lycopodium, were as easily ignitable as the most easily ignited air dispersion. Thus, an unanswered question has arisen concerning the role of surface coatings in the flammability of all marginally ignitable mixtures.

Jan 1, 1981

Until man was able to produce light, his working day was pretty much limited to daylight hours. Underground miners have a special problem because in a mine it is just as dark during daytime as it is at night. The first devices used for mine lighting were torches and open flame 011 lamps. Torches made from twisted grass and dipped in tallow or pine pitch would burn for a while, but they made a lot of smoke and probably went out when they were needed most. During the 15001s, miners lamps consisted of a small metal dish with a hook attached to hang it up. The saucer-shaped dish was filled with animal or fish oil and a wick made of twisted fibers was laid In the 011 and hung over one edge where it would burn. This lamp would burn longer than a torch, but the amount of light cast by the pale, flickering flame was probably only a little better than no light at all.

Jan 1, 1976

By Gerald L. Finfinger

The Bureau of Mines conducted an experimental degasification project in Island Creek Coal Co.'s Virginia Pocahontas No. S mine. Methane from the overlying Pocahontas No. 4 coalbed was entering mine workings in the Pocahontas No. 3 coalbed through fractures in the roof rock. Small-diameter (l-S/B-inch) holes were drilled into the overlying coalbed to reduce the gas pressure and intercept methane flows, which were piped to the surface through an underground 6-inch-diam steel pipeline. The total methane flow rate from the vertical holes averaged 150,000 ft3/day for the first month. Methane flows into the mine were reduced by 47 pet, thereby demonstrating the effectiveness of this form of degasification in reducing ventilation requirements and providing a safer working environment.

Jan 1, 1979

By K. K. Kelley, W. W. Weller

The heat capacities of four crystalline silicates of barium ( BaSiO3 , BaSiO4 , Ba Si¸0 , and BaSi₂0 ) and two crystalline silicates of strontium (SrSio and Sr₂Sio ) were measured over the temperature range from 51 ° to 298° K. The results were used to evaluate the entropies at 298.15 ° K. The entropy values were joined with known heats of formation to obtain the free energies of formation of the silicates with respect to their constituent oxides at 298.15 ° K.

Jan 1, 1964

By E. C. Lane

The motor gasoline that is being marketed in the United States this winter is practically the same 'as that sold a year ago. In fact, there has been little char sin this commodity during the year, as the gasoline sold last summer was almost as volatile as that marketed last winter. Boring the past eight years, the Bureau of Mine's has made semi-annual surveys of the gasoline marketed in the United States, the survey just completed being the fifteenth in the series. The cities in which samples have been collected have been chosen as representative of the more important marketing territories as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country.

Jan 1, 1927

By Wm. W. Odell

This report comprises a brief outline of the experimental cracking of natural gas in a water-gas generator at Louisville, Kentucky, and a discussion of the results obtained. The work was done under a cooperative agreement by the U. S. Bureau of Mines with the Louisville Gas & Electric Co. The re-forming or partial cracking of natural gas is not a new process, but one which has been employed in the manufacture of city gas for a number of years. However, the apparatus used heretofore was not a water-gas generator containing a bed of ignited fuel, but instead it was a plurality of connected chambers containing spaced and arranged checker bricks, with means for heating the bricks and for admitting the natural gas. The procedure previously followed was quite different from that used during the tests at Louisville; likewise the results obtained were different. It is not uncommon for companies distributing natural gas to provide gas-generating equipment for producing manufactured gas which is used, mixed with natural gas, during periods of peak demand. Because this equipment is idle much of the time, in some instances being in use only for a few days a year, some of the gas companies have considered using it, during off-peak periods, in the manufacture of some gaseous products and for carbon black which might he produced and marketed with profit. There is one plant of this kind at Louisville. Kentucky. Its maintenance in condition ready to be operated is necessary because of the limited supply of natural gas and because of the variation in demand. The engineers of the Louisville Gas & Electric Co. considered in particular the possibility of cracking natural gas in a water-gas generator by injecting the gas into the incandescent fuel bed, thereby producing a gas comprised largely of hydrogen (H2) and carbon black, an appreciable amount of which is entrained in the gas as it leaves the generator, Because power and gas are available at low prices, Louisville was believed to be a satisfactory location for a plant which could use hydrogen. It was evident that this method of treating natural gas might directly benefit the gas company by: 1. Lowering, the cost of manufactured gas.

Jan 1, 1930

1. A total of 14,413 mining operations reported employment to the Mine Safety and Health Administration (MSHA). Nearly half (48.9%) were sand and gravel operations, followed by stone (28.5%), coal (14.7%), nonmetal (5.7%), and metal mines (2.1%). 2. Mine operators reported 240,000 full-time equivalent workers1 (down 3.9% from 1999). Independent contractors reported 42,000 full-time equivalent workers working on mine property (up 8.6% from 1999). Coal operators accounted for 26.8% of reported employee hours, followed by stone operators (25.9%) and sand and gravel operators (12.1%). 3. Eighty-four (84) work-related mine fatalities occurred in 2000 compared to 90 the year before. •The mine fatality rate was 29.8 per 100,000 full-time equivalent workers compared to a fatality rate of4.6 per 100,000 employees for all private industry. •Thirty-one percent (31%) of the fatalities occurred in underground work areas, which account for only17% of total employment. •Although the largest number of fatalities (28) occurred among miners who work for coal operators, coal contractor employees had the highest fatality rate (61.1 per 100,000 full-time equivalent workers). 4.There were 10,839 nonfatal lost-time injuries reported to MSHA, occurring at a rate of 3.8 injuries per 100full-time equivalent workers, and resulting in a total of 417,918 lost workdays.2 •Among all employees,3 the highest injury rate occurred among coal operator employees (5.6 nonfatal injuries per 100 full-time equivalent workers). •The highest percentage (34.7%) of nonfatal lost-time injuries were due to handling materials (e.g., over-exertion in lifting, pulling, or pushing objects), which also accounted for the greatest percentage of lost workdays (29.3%). •Among the most frequently occurring injuries, the most severe (as measured by the median number of days lost) were associated with accidents involving falls of ground, the use of powered haulage, and slips or falls. •The most frequently reported part of the body injured was the back (22.9% of all injuries). Back injuries accounted for the highest percentage of lost workdays (21.6%). 5.Seven hundred sixty-seven (767) cases of occupational illness were reported to MSHA. •The most frequently reported illness was repetitive trauma, resulting in joint, tendon, or muscle inflammation or irritation (37.3%). •There were 155 (20.2%) illnesses reported as hearing loss. The majority (68.4%) of hearing loss cases occurred among surface workers. •Coal workers' pneumoconiosis accounted for 14.5% of reported illnesses.

May 15, 2002

By V. E. Homme, M. M. Wong

Tests were made in reactors ranging from 12 to 30 inches in diameter to develop methods for the preparation of sodium chloride - titanium lower chlorides ( dichloride and trichloride ) melts that contain titanium predominantly in the divalent state . Such melts are desirable as a starting material for the production of titanium metal or as an electrolyte for electrorefining of titanium . Sodium reduction of TiCl with an 18 - hour period of holding the reaction products in the molten state produced melts that contained titanium lower chlorides in TiCl₂ - to - TiCl , molar ratio of approximately 8 to 1. Sodium reduction of TiCl in a reactor with a shielded pipe weir , that required no melt -holding period , produced melts with a TiCl₂ - toTiCl , molar ratio as low as 4 to 1 . Reduction of TiCl4 with scrap titanium metal in molten sodium chloride produced relatively pure melts containing about 27 percent titanium in a Ticl₂ - to - Ticl , molar ratio of approximately 4 to 1 .

Jan 1, 1964

By Stanton L. Tainter

When the disruption of gold mining stopped the usual source of siliceous flux needed by copper smelters , sandstone copper deposits in northern Arizona offered possibilities as a source of the flux during the war emergency . The Federal Geological Survey , while making a comprehensive survey of sandstone copper deposits , investigated the Warm Springs mining district in northcentral Coconino County in August 1943. A month later , J. H. Hedges , chief of the Tucson Division , Mining Branch , Bureau of Mines , examined the operations in connection with an application for an access road . Both investigations concluded that the district , as an emergency source of copper-bearing siliceous flux , had considerable merit , provided high prices for copper continued in effect . Early in 1944 , V. M. Ryan and S. B. Atherley requested assistance from the Bureau in exploring various deposits on their property . The Bureau / drilled 152 holes , aggregating 3,756 feet , on the Petoskey and Mackin groups of claims . This report is based upon churn drilling done under contract from October 7 to November 25 , 1944 .

Feb 1, 1947

By Alla D. Mah

Relatively pure aluminum nitride (AIN) recently has been prepared in sufficiently large amounts to permit a variety of experimental studies.4/ Several mechanical and chemical properties have been investigated, which show that this substance has good potentialities as a container for liquid aluminum, gallium, and boric oxide. The present work by the Bureau of Mines was undertaken to obtain thermo-dynamic data pertinent to the calculations regarding thermal stability and reactivity of aluminum nitride. The following measurements were made: (1) determination of the heat of formation from the elements at 298.15° K.; (2) determinations of the heat capacity over the temperature range 51° to 298.15° K. and the evaluation of the entropy at 298.15° K. therefrom; and (3) determinations of the heat content over the temperature range 298.15° to 1,800° K. These data are combined to obtain free energies of formation from the elements between 298.15° and 2,000° K.

Jan 1, 1961

By C. Fang, D. B. Kittleson, K. L. Rubow

"Under contract to the U.S. Bureau of Mines, a study was conducted to investigate the feasibility of using the microorifice. uniform deposit impactor (MOUOI) to measure the size distribution of aerosols containing various mixtures of coal dust and diesel exhaust particles. The project objective was to determine if the mass concentration of diesel exhaust particles, in an airborne mixture of coal dust and diesel exhaust particles, could be determined on the basis of the size distribution of the two aerosols. In general, the mass of diesel exhaust particles is in the submicrometer size range while that of the coal particles lie in the larger size ranges.The MOUDI is a cascade impactor with small diameter nozzles to obtain small cut sizes and rotating impaction plates to avoid particle overloading of the deposit. For this study, a 7 stage version was used. At the sample flow rate of 30 L/min, the cut sizes were 0.10, 0.23, 0.70, 1.0, 2.6, 4.9 and 10 pm.Size distributions of aerosols generated in the laboratory and in several underground coal mines were measured. The primary emphasize of the laboratory tests was to ascertain if the diesel exhaust particles could be separated from the coal dust, regardless of mass fraction of the diesel exhaust particles in the total aerosol mixture. Diesel exhaust, from a Caterpillar Type 3304 NA diesel engine, was mixed with coal dust generated with a· TSI Model 3400 fluidized bed dust generator. Experiments showed the size distributions of the mixed aerosols exhibited two definite modes with the minimum between the two modes in the 0.7 to 1.0 um size range. Distinct modal separation was obtained as the mixture fraction of the diesel exhaust aerosols was varied from 3% to 98%.The field study was conducted in three underground coal mines, two utilizing diesel-powered equipment and the third exclusively using electric equipment. Sampling sites were selected to obtain a wide variety in the diesel exhaust and dust aerosol concentrations. Size distribution data showed these aerosols are bimodal. The mass median aerodynamic diameters of the diesel particulate mode and the coal dust mode were approximately 0.15 µm and 3 to 10 un, respectively. The results, in all cases, clearly show a separation between the two modes in the 0.7 to 1.0 µm size range with the minimum in the vicinity of 0.8 pm. The separation was found to be independent of mass fraction of the diesel exhaust particles, total particle concentration and sampling site."

Jan 1, 1989