Search Documents

By P. M. Sullivan

At its College Park Metallurgy Research Center in Maryland, the Bureau of Mines has installed and is operating a 5-ton-per-hour pilot plant for continuous mechanical separation of values contained in raw urban refuse. The entire sys tern was assembled using commercially available equipment. The process relies on multistage processing including shredding, air classification, screening, gravity concentration, and electrostatic separation. Compactor trucks deliver raw refuse collected along typical routes in metropolitan Washington, D.C., to the pilot plant. The loads are separated into concentrates of (1) light-gage iron, (2) massive metals, (3) glass, (4) putrescibles and waste combustibles, (5) paper, and (6) plastics. While some refinements remain to be made in the processing system flow-sheet, the data obtained to date have been highly encouraging, indicating favorable economics for commercial-size plants.

Jan 1, 1973

By Fred R. Biggs

This report was prepared by the U.S. Bureau of Mines to present a brief history of the listing of Iron Mountain Mine as a Superfund site on the National Priorities List (NPL) and subsequent remedial actions. The mine area is located on 4,400 acres near Redding, CA, and includes underground workings, an open-pit area, waste rock dumps, and tailings piles. This property involves multiple sources of acid mine drainage (AMD) that are high in copper, zinc, and cadmium. The selected remedial actions, based on the Record of Decision of 1986, would partially cap the Richmond mineralized zone to reduce infiltration of clean water, divert clean surface waters away from contaminated areas, fill surface subsidence areas, and enlarge the Spring Creek debris dam to provide increased surge capacity. Site remediation efforts at Iron Mountain are well into the remedial design-remedial action phase. Costs to date for remedial action are $7.5 million. Details of activities and designs of remedial elements are presented and future activities discussed.

Jan 1, 1991

By W. T. Millar

Graphite in the Suffern deposits near Hillburn, N. Y., consists of flakes ranging in size from fines to one-half inch in diameter. The Bureau of Mines investigated the Suffern deposits in the spring of 1943. Gneiss outcrops were examined, and five trenches excavated and sampled. The graphite is not confined to any definite zone but occurs in small, local pockets. Eleven samples were collected and combined for laboratory tests. Tests by the Bureau of Mines indicate that the graphite ore can be beneficiated by stage crushing, "skin flotation" of coarse flakes, and wet flotation of minus 10-mesh flakes. Over 90, percent of the graphite was recovered.

Jan 1, 1949

By M. H. Marvin

This report presents the results of a program to develop backfilling techniques to mitigate undesirable effects of hydraulic borehole uranium mining. Large underground cavities, formed during the borehole mining process, can be backfilled to prevent ground subsidence and to allow mining of adjacent uraniferous sandstone. Three backfilling techniques were tested in the laboratory and in the field: bulk dumping of slurry into the borehole from ground level, slurry injection under water, and slurry injection above the cavity water level. These techniques were tested with sand and with sand and one percent cement (by weight) mixtures. The project was accomplished in four tasks: equipment preparation and transport, mining operation to generate a full-sized cavity, backfilling operation, and assessment through core samples and subsidence checks. The concentrations of cement mixed with sand proved to be inadequate to bond the sand. Bulk dumping resulted in a 30-degree angle-of-repose, much too steep to completely fill the cavity. Both slurry injection techniques filled the cavity satisfactorily. However, underwater injection is the recommended backfilling technique because the borehole water level does not need to be pumped down during backfilling. The borehole itself was filled by bulk dumping of slurry. In conclusion, backfilling of borehole mining cavities is entirely feasible, and the preferred method is slurry injection under water.

Jan 1, 1979

By Raymond M. Stateham

A portable, handheld infrared scanner has been used to detect abnormal surface temperature on dumps of flood-generated trash near Wilkes-Barre, Pa. Three of eight dumps examined had thermal anomalies on the surface, indicating temperature buildup at depth. The anomalies found with the scanner were verified by measurements with a thermocouple probe or a carbon monoxide detector. One week after the investigation was completed, open fire broke out at the site of one of these thermal anomalies; about 6 weeks after the investigation, a thermal anomaly in another dump was verified when a trench was excavated in the dump.

Jan 1, 1973

By Robert L. Virta

The Bureau of Mines examined a fibrous talc sample from the Gouverneur talc district in New York by transmission electron microscopy (TEM) and polarized light microscopy to determine the mineralogical relationship of the fibrous talc to the amphiboles present in the sample. Two am-phiboles, anthophyllite and tremolite, were present in the sample. Tremolite occurred as a separate mineral phase, which was blocky in habit. Only a few composite tremolite-talc grains were observed. An-thophyllite, however, was present only in the fibrous talc grains. Mi-crodiffraction study of the fibrous talc grains containing anthophyllite showed that the anthophyllite was intermixed with the talc on a fine scale and that there was a crystallographic relationship between the talc and anthophyllite lattices in the fibrous talc grains. A mechanism similar to the process that forms biopyriboles could explain the structural defects, the fibrous habit of the talc, and the structural relationship between the talc and anthophyllite in the fibrous talc grains. Because of these characteristics, phase contrast microscopy and a provisional TEM technique for monitoring asbestos exposure would not distinguish between fibrous talc and fibrous amphiboles. TEM techniques employing electron diffraction and energy-dispersive X-ray analysis are recommended to positively identify the fibrous phases for regulatory purposes.

Jan 1, 1985

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) measurements on solutions and isolated powders provide direct evidence for the involvement of Cr(V) species in the reduction of Cr(VI) by NAD(P)H. ESR analysis of an isolated Cr(V)NAD( P)H solid yields 6 11 = 1.9831 and 6.i. = 1.9772, indicating that the unpaired electron occupies the d22 orbital of the Cr(V) ion, with square-pyramidal geometry. Addition of hydrogen peroxide (H2 0 2 ) to the N AD(P)HCr( VI) reaction mixtures suppresses the Cr(V) species and generates hydroxyl (""OH) radicals. The ""OH radicals were detected via ESR spin trapping, employing 5,5-dimethyl-1-pyrroline-N-oxide and a-(4-pyridyl-1- oxide)-N-tert-butylnitrone as spin traps. The dependence of Cr(V) and ""OH radical formation on the H20 2 and Cr(VI) concentrations indicates that the Cr(V) species react with H20 2 to generate the ""OH radicals. Similar results were obtained by using various diols (arabinose, cellobiose, FAD, fructose, glyceraldehyde, ribose, and tartaric acid), a-hydroxycarboxylic acids, and glutathione. Investigations with superoxide dismutase showed no significant participation of 02 in the generation of OH radicals. These results thus indicate that the Cr(V) complexes, produced in the reduction of Cr(VI) by cellular reductants, react with H20 2 to generate ""OH radicals, which might be the initiators of the primary events in the Cr(VI) cytotoxicity.In this paper we report an electron spin resonance (ESR)3 spectroscopic detection of Cr(V) species in the reduction of potassium dichromate, henceforth called Cr(VI), by NAD(P)H and other diols. Also reported here is the detection of the hydroxyl (""OH) radical in the reaction between hydrogen peroxide (H2O 2) and a variety of Cr(V) complexes. This work was undertaken because while the reduction of Cr(VI) to lower oxidation states has been suggested as a key step m the mechanism of Cr(VI) toxicity, mutagenicity, and DNA alteration, the details are not yet clear (1-5).Earlier studies on the mechanism of Cr(VI) reduction in cellular systems include those on the reduction of chromate by microsomes (6-8), rat liver DT-diaphorase (9), and aldehyde oxidase (10). All these studies imply that Cr(VI) can be reduced to Cr(Ill) by cellular constituents. Regarding the mechanism of Cr(Vl) carcinogenicity, Jennette postulated that Cr(V) is the ultimate carcinogenic form of chromium compounds (8). This conclusion has led to many further investigations of the formation of Cr(V) in the reduction of Cr(VI) under biologically relevant conditions (11-33). More recently, however, Kawanishi and co-workers (34) have investigated the mechanism of DNA cleavage induced by Cr(VI) in the presence of H20 2 and have argued that it is not Cr(V) itself that is carcinogenic, but it is the reactive oxygenated species (02, 10 2 , ""OH) (produced by the decomposition of the Crv(02) ¾ - ion) that cause the DNA alteration."

Jan 1, 1990

By A. E. Isaacson

The U.S. Bureau of Mines determined the effect of common sulfide minerals on the corrosion rates of various types of ferrous alloy grinding media. Data obtained from this study will aid in determining the contribution of any electrochemical reactions between sulfide minerals and grinding media to the total grinding media consumption. Common sulfide minerals used in this study were chalcopyrite, galena, and sphalerite. In the presence of oxygen, chalcopyrite was found to increase the corrosion rate, galena was found to decrease the corrosion rate, and the effect of sphalerite was dependent upon the type of grinding media. Possible electrochemical reactions of these minerals in the presence of grinding media are suggested.

Jan 1, 1989

By P. R. Bremmer

As part of a program to devise alternative technologies for producing alumina from domestic resources, the Bureau of Mines investigated the leaching of calcined kaolinitic clay to form basic aluminum chloride solutions. Bench-scale experiments were conducted for single-stage batch leaching with AICl3 solution and three-stage countercurrent leaching with substoichiometric HCI. Variable conditions of clay calcination and leaching were studied to determine their effects on aluminum extraction and pregnant liquor composition,

Jan 1, 1984

By A. G. Starliper

Laboratory studies were made to produce whiskers of tungsten over a wide range of operating temperatures. Hydrogen reduction of tungsten hexachloride in a vacuum furnace at temperatures from 2,7000 to 3,3000 C yielded a small quantity of tungsten whiskers, provided a low degree of supersaturation was maintained. Direct measurements of 3,000,000 to 4,000,000 psi were obtained for the ultimate tensile strengths of individual whiskers averaging 3 to 4 microns in diameter with average aspect ratios of 1,000. This compares with strengths of 300,000 to 400,000 psi for 13-micron-diameter commercial filaments.

Jan 1, 1968

By Thomas L. McVay

Laboratory batch and pilot plant flotation tests were made to determine the feasibility of recovering commercial grade kyanite from a quartzite- kyanite rock from the Graves Mountain, Ga., deposit. Best results in laboratory and continuous tests were obtained using sodium carbonate for pH control, citric acid for quartz depression, and oleic acid as the kyanite collector. Over 80 percent of the kyanite was recovered in a concentrate analyzing 56.8 percent Al203 and 3.8 percent hydrochloric acid soluble Fe203. Subsequent treatment of the flotation concentrate by magnetic separation reduced the acid soluble Fe2O3 to 0.6 percent and increased the alumina content to 59.2 percent. Acid leaching of the concentrate gave a product analyzing 59.7 percent Al203 and about 0.1 percent Fe203. As a result of the beneficiation research, a commercial kyanite flotation plant was completed in September 1962 by private industry.

Jan 1, 1963

By H. M. Smith

[ ]

Jan 1, 1927

By G. W. Birge, D. E. Wolfson, J. H. Lynch

This report presents all available 900 ° C BM- AGA carbonization and related data for coals from the principal beds of the southwest Virginia field in a form which permits ready comparison of product yields and properties of coals and cokes . Thirty- one channel samples from Buchanan , Dickenson , Russell , Tazewell , and Wise Counties were carbonized at 900 ° C in an 18 - inch - diameter retort . Blending properties of 10 of the coals were studied , and expansion of most of the coals and blends was measured in the Bureau of Mines sole - heated oven . Ash Most of the samples were chemically suitable for metallurgical use in coking blends , and their coking properties generally were satisfactory . content exceeded 10 percent in only three samples , and none of the coals contained more than 1.5 percent sulfur . Dry , mineral - matter - free fixed - carbon content of the coals ranged from 62.1 to 77.5 percent . Expansion behavior varied widely , ranging from 16.8 percent expansion to 27.6 percent contraction .

Jan 1, 1964

By Frank L. Hess

In the first cart of that little space of time that we have designated as the nineteenth century, chemistry had reached a wonderful stride. Viewed from the present heights attained by the efforts of innumerable chemists with perfected apparatus, mire reagents, air under pressure, water, gas, and electricity conducted to the desk, and. numberless other helps, it seems marvelous that chemists of that day obtained such results. In 1820, about half of the elements had. been discovered; of these discoveries, Swedes had made 15 or more, about once-third of the elements then known and nearly half of those discovered after 1700.

Jan 1, 1939

By C. R. Bopp, N. A. C. Smith

"For a period of several years, beginning with 1915, there has been a continuous change in the quality of motor gasoline. The average volatility has decreased, this to the fact that higher boiling fractions of the crude oil have been included in the gasoline. This change in quality was made necessary by the tremendous increase in the demand for motor fuel, caused by the development of the motor car, and during the war was an absolute necessity to avoid gasoline shortages. The Bureau of Mines has kept in close touch with this situation by making surveys from time to time of the gasolines sold throughout the country, as this information is of value to manufacturers and users of motor cars and also indicates when any changes are required in the Government specifications. The Bureau has just completed a gasoline survey and is in a position to make public the fact that there has been very little change in the quality of motor gasoline in recent months.During the period from January 17 to February 3, 1920, 81 samples of actor gasoline were collected by representatives of the Bureau of Mines in seven districts of the United States. The cities selected for this survey were New York, N. Y., including Brooklyn; Washington, D. C.; Pittsburgh, Pa.; Chicago, Ill.; New Orleans, La.; Salt Lake City, Utah; and San Francisco, Cal., including Berkeley. In every case the samples collected were taken in such a manner as to represent material actually being sold as motor fuel, and to include samples from each refinery marketing in the district."

Jan 1, 1920

By A. B. Hooker

Gassy mines require daily inspections with methane detectors to test for the presence of methane. Although in many manes it may be sufficient to know that there is no methane present or that its percentage is below a certain amount, it is desirable and often necessary to determine definitely the percentage of methane at the working faces and in the various air currents. The Bureau of Mines recognizes two general types of portable methane detectors, namely; 1. Methane detectors by which the presence of methane may be detected and its approximate percentage estimated.

Jan 1, 1929

By H. R. Babitzke

The purpose of this Bureau of Mine- investigation was to develop columbium and tantalum alloys suitable or u at elevated temperatures. Columbium and tantalum were combined with tungsten, hafnium, zirconium, molybdenum, vanadium, and titanium, and the resulting alloys were evaluated with respect to workability, hardness, electrical resistivity, strength at elevated temperatures, oxidation resistance, and weldability. Cb-33Hf-10W-10Ti, Cb-20111-5Mo, and Cb-30Hf-5Mo exhibited superior high temperature properties. Cb-33Hf-10W-10Ti had tensile strength values of 44,300 psi at 1,200° C and 16,500 psi at 1,400° C, Cb-20Hf-5Mo had values of 35,700 and 20,700 psi, respectively. The corresponding values for Cb-30Hf-5Mo were 38,900 and 17,800 psi. These alloys are fabricable by conventional methods with excellent strength at temperatures up to and including 1,400° C. An oxidation rate of 7 to 21 mg/cm2/hr was observed up to 1,000° C.

Jan 1, 1967

By W. K. Kleysteuber

This report covers the design and testing of a novel bulk materials conveying device by the Bureau of Mines. The transport concept of the device is to create a traveling wave with a steep front so that the bulk material slides and cascades down the front of the wave with some horizontal motion. Ideally, the front should act like a continuous chute. The concept of moving bulk materials along a belt without any forward movement of the belt itself was demonstrated. The conclusions reached were that the mechanism as designed could not overcome the inherent major disadvantages that would make the undulatory conveyor suitable for practical applications.

Jan 1, 1974

By E. J. Gleim

[of- ac tore affecting the e -success of recent conveyor miningsystems forLt. extraction. 1 GL C ,_tfreedom shoot &apos;_)`u 2--ethe.1 is coal while e en othershot firers re:7 t _e&apos; _U-tin , w J, e coal .Z- 311.ing States conveyors because ;-.;lax .ca requires thatblasting be limited to when c .. men os. _o tend neces¬sary officials 1 s . re out c-z ,r 7t ...y e:e l z<: woes no t a -¬#to 1 C" such restriction on blasting conveyor miningbeen extendedWhere ere t ere. re no _ c: t&apos;_ _c tit-----! . kind cutlasting;,1CL?; C&apos;. _ z)carried anI-7LC. AT continuouslyHowever, unless et._&apos;0:, precations are taken under r&apos;t e , accidents, n is or such, as111 electricity r 1C- from.J--_,._.1t ,° =&apos;1?without usingholes, as well as numerous-o _&apos;1&apos;-1 -= e troublehe record of mineexplosions (some of themSo so _C&apos;_ °:&apos;,v 0f rock- dusting]

Jan 1, 1941

By V. E. Homme

Low- and high-temperature reduction techniques were employed by the Bureau of Mines in study of conditions favorable to the formation of massive titanium crystals. &apos;1,1,2 low-temperature method, feeding molten sodium to solidified titanium lower chloride-sodium chloride, produced higher quality and high quantity crystalline metal. The percentage of crystalline titanium was increased with increasing reactor diameter, melt depth, and titanium dichloride concentration. The high-temperature technique, feed molten sodium to melts above 8000 C, producing needle-type crystals of lower quality and with less consistent results than the low-temperature method. Layers of titanium foil, sponge, fine needles, wool, and crusts of sin-tered granules were formed during the earl, -art of the low-temperature reduction, and massive crystals were produced beneath this barrier in the latter part of the reduction. Crystalline titanium having an average hardness of Bhn 76 and representing 58 percent of the total titanium was obtained. Lamellar crystals up to 1 1/2 inches long with a hardness as low as Bhn 54 were also produced. A second-stage reduction for reclaiming titanium from offgrade sponge is described. Titanium produced by this method was comparable in quality to that from sodium reduction of titanium tetrachloride.

Jan 1, 1966