Search Documents

By Jack D. Ramsdell

Electrorefined, magnesium-reduced, and sodium-reduced titanium samples were evaluated for recrystallization behavior, effect of cold rolling on tensile properties, and bend ductility. Curves were determined for the softening of 2.5 to 80 percent reduced cold-rolled metal that was annealed over a temperature range of 300° to 800° C. Upon annealing, coarsening of the grains was found to occur for reductions in thickness of less than 20 percent in titanium made by all three processes. The presence of metallic impurities greatly inhibits coarsening for reductions in thickness below 20 percent, but for reductions in excess of 20 percent grain size is essentially constant at each annealing temperature. The three grades of titanium did not harden excessively from cold rolling; both tensile and bend ductility were good for reduction in thickness up to 80 percent. Upon annealing, softening occurs between 400° and 600° C., and, based on microstructure and property studies, full annealing is accomplished after 30 minutes at 700° C. for the magnesium-reduced and electrorefined titanium and at 800° C. for the sodium-reduced titanium.

Jan 1, 1960

By Raja V. Ramani

The recognition that surface mining need not be viewed as a permanent dedication of the land but rather as a temporary non-renewable use in a series of land uses has caused greater emphasis on the re-use of surface-mined lands. In an effort to develop a procedure for evaluating postmining land use potentials, specific mines in various regions of the U.S. have been studied to determine the extent of current mined-land planning and to discover characteristics that are regional in nature. As part of this investigation, the Indian Head Mine, which is located in Mercer County, North Dakota, has been studied. The Indian Head Mine is presently operated by The North American Coal Corporation -Western Division and has been in operation since 1917 under various ownership. The status of current reclamation and postmining land use planning was reviewed. In addition, the relationship between mine planning and public planning in an area impacted by energy development was investigated. Finally, key factors affecting site potential realization for western surface mines have been identified.

Jan 1, 1983

By R. Burrell, N .. L. Lapp

"Except for asthma and pulmonary infections, the types of lung disease that have been of immunologic interest the longest are the various mineral pneumoconioses. Because of their chronicity, type of pathology produced, and well-known immunotoxic properties associated with the dusts inciting them, the pneumoconioses have long drawn attention to the possibility that the immune system has not only been modulated but that its effectors have possibly contributed to their pathogenesis. All of the mineral dusts reviewed here have definite immunomodulating properties and act on various cellular and molecular components of the immune system. Further, each has an immunotoxic potential to induce either hypersensitivity (as in the case of beryllium) or other types of immune injury. This article reviews the immunologic aspects of the four major occupational minerals that have an immunologic impact on the lung: asbestos (particularly chrysotile), silica or quartz, beryllium, and coal mine dust.These agents have many things in common, yet each is distinctive. Although the possibility still exists that these mineral particles can adsorb intrinsic tissue antigens or extrinsic organic antigens to their surfaces and initiate immune responses to the adsorbed antigens, only one, beryllium, can act as an antigen itself. Silica is a profound macrophage toxin and thereby exerts many effects on those factors controlled by macrophages. Asbestos has undergone the most immunologic studies resulting in a much dearer picture of how it may contribute to immunopathology. Coal mine dust is the agent about which least is known immunologically, partly because there is no such thing as purified coal mine dust or a standard by which coal mine dust can be defined. Indeed, there are studies that use only the dust from the ground coal itself, whereas other studies use the total dust collected from air samples of a working mine in the belief that other types of dusts (e.g., silica from roof bolt drilling, from sand ground on the rails by cars, and from surface drilling) contribute to the disease (Figs. 1 to 5). This properly is coal mine dust and is poorly characterized. Yet, workers exposed to these dusts share similar reactive characteristics and they may be considered collectively as well as individually."

Mar 1, 1992

By H. W. St. Clair

In about 1930, Degussa applied for a patent on a process for the of oxides, carbides, sulfides, and other nonmetallic impurities by filtration in the molter state. The filtering media listed were wire screen, coke, and ceramic materials, and quartz. It was also suggested that filtration might be combined with chemical reaction between the metal and the filter medium or that might be added to the system. No patent was granted on the general scheme, but several years later a patent was granted on a continuous process purification of crude light metals, especially or alkali earth and their alloys. The melt was stirred at 1 temperature at which the impurities (such as oxides and salts) remained solid and the metal was drawn through a filter tube. The impurities collected under the filter and were removed by a screw conveyor. Crude sodium was purified by this process in Degussa's Knapsack plant. During the last war, when the refining of scrap became a very urgent Problem in Germany, experimental investigations were extended to separation of other metals and metallic compounds by filtration. Preliminary experiments seemed to confirm the opinion of Dr. L. Weiss that the principles of wet chemical filtration might be applied to a great extent in the purification of metal and alloys.

Jan 1, 1949

By J. A. Rowland

Magnesium alloys containing nickel, nickel and manganese, lithium, lithium and manganese, and lithium and aluminum were investigated. Melting, casting, and mechanical working techniques and the heat treatment of various compositions were studied. Amenability to cold and hot working was shown for many compositions. The magnesium-nickel and magnesium-nickel-manganese alloys failed to develop superior mechanical properties and were very low in resistance to corrosion. The magnesium-lithium series, although entirely plastic, had low strength properties. The addition of small amounts of aluminum to the Mg-Li base did not affect greatly either the ductility or the strength; further additions developed increased strength, but only at room temperature, and the alloys became brittle with age. Continued study, concentrating on the ductile lithium-rich beta phase as a base composition for ternary and quaternary systems, is recommended.

Jan 1, 1956

By Robert E. Barieau

In the design of plants to separate helium from natural gas , it is necessary to estimate the enthalpies of the various streams at various positions in the process . This Bureau of Mines report surveys the various methods that have been used to determine enthalpies and gives information on the organizations with such capabilities . The minimum information required for developing an enthalpy diagram is presented , and the relative merits of the various methods are discussed . It is concluded that methods that require no mass flow rate or energy measurements are to be preferred .

Jan 1, 1965

By K. O. Bennington

Thermodynamic properties were determined by the Federal Bureau of Mines for lithium metasilicate (Li2Si03) and lithium disilicate (Li2Si205). Their enthalpies of formation were investigated by hydrofluoric acid solution calorimetry. The standard values are ?Hf°298 -393.8 ± 0.8 kcal/mole for Li2Si03, and ?Hf°298 -611.8 ± 1.0 kcal/mole for LiSi205. Enthalpy increments above 298 K were measured by copper-block drop calorimetry from 298 to 1,404 K for Li2Si03, and from 298 to 1,281 K for Li2Si205. Low-temperature heat capacities were determined adiabatically from 6 to 305 K for Li2Si205 only. The derived standard entropy is S°298 = 29.20 ± 0.10 cal/deg-mole. The various experimental data were combined with other data from the literature, and resulting properties of ?Hf°, ?Gf°, and log Kf were tabulated as a function of temperature.

Jan 1, 1976

By L. B. Pankratz

Enthalpies above 298° K were determined for AgCl to 1,400° K and for AgBr to 1,200° K by copper-block calorimetry. Before melting, both compounds showed an anomalous increase in enthalpy, an effect associated with lattice defect formation. Melting points and heats of fusion were determined to be AgCl, 730° K and 2,945 cal/mole; AgBr, 700° K and 2,030 cal/mole. The heat capacity of both melted substances decreased with increasing temperature over the entire liquid ranges investigated. Enthalpies above 298° K were tabulated at even temperatures along with derived entropy increments and heat capacity values. The results were combined with the known heats of formation and entropies at 29.8.15° K to obtain values of the heats and free energies of formation over the range 298.15° to 1,400° K for AgC1 and 298.15° to 1,200° K for AgBr.

Jan 1, 1970

By Jerome J. Hoeppner, Walter W. Fowkes

The Federal Bureau of Mines has determined the distribution of forms of sulfur for several lignites and gasification chars and noted the changes induced by the gasification process . A method was adopted for quantitatively determining sulfide sulfur that was found to be present in the chars , although absent in the lignites . Changes in the behavior and distribution of sulfur forms were further investigated concerning the ashing of lignites and chars under standard conditions , as well as at various temperatures , and the determination of volatile matter applied to both chars and lignites . The authors concluded that the first and greatest change in the form of sulfur present in natural lignite , upon heat treatment , resulted from the reduction of pyritic and sulfate sulfur to sulfide . Organically - bound sulfur originally present is less reactive , but largely disappears on strong ignition . An appreciable part of the sulfur content of natural lignite is fixed in the char as sulfide and in the ash as water - soluble sulfate and will affect the summation of constituents , to a greater or lesser degree , in reporting the ultimate analysis of a lignite or char .

Jul 1, 1960

By E. C. Lane

During the past 15 years the Bureau of Mines has made and published several hundred analyses of typical petroleums and has developed a system of interpreting the analyses and of classifying crude oils. In describing crude petroleum frequent reference is made to the "base" of the oil, a usage the petroleum industry has found convenient. As part of its general study of the characteristics of crude oils, therefore, the Bureau of Mines has developed a system of classifying them according to "base." This system as first published in 19274 was limited to four classes and in its original form is no longer considered adequate. Since the system was first published the Bureau has analyzed a large number of crude oil-, including representative samples from nearly every important producing field in the world, and has found that the system of classification could be revised and amplified to advantage. The revised system is presented herein. Bulletin 2916 states that many oil producers and refiners use the word "base" much as it is used in pharmaceutical work. For example, the "base" or "basis" of an ointment or salve is the fatty material (lard, petroleum, or lanolin) used as a vehicle or carrier for the active medicinal principles. Apparently many of the pioneers in the petroleum industry considered crude oil similar in nature to these medicinal products in that it consists of a semisolid, nonvolatile base and 1 volatile portion can be distilled off to make gasoline, kerosene, and other products. Many crude oils when chilled slowly deposit a waxy material (paraffin); this fact may have been one reason for the use of the term "paraffin base" in referring to such oils. Almost all of the petroleum first discovered in the United States was of this nature; not until the oil industry was extended to California and along the Gulf coast was petroleum found that contained no wax but apparently did contain asphaltic material Accordingly, these oils were known as "asphalt-base" oils. The use of this term, however, seems unfortunate, as better-grade oils of this type contain little if any asphalt; the descriptive term "naphthene base" now seems to be a more desirable term than "asphalt base." The term "intermediate base" is also used commonly in referring to oils intermediate in oharacteristios between those of paraffin and naphthene base.

Jan 1, 1935

By R. Hogg

"The basic population balance models for agglomeration processes are reviewed and procedures are described for extending their applicability to systems with size-dependent rate constants and to the formation and growth of porous agglomerates from rigid, solid-particles. Simplified procedures for the further extension of the models to include simultaneous agglomerate growth and breakage are also described.INTRODUCTION The association of small particles into clusters or agglomerates is a significant factor in many facets of particle processing. Agglomeration processes are widely used to facilitate handling, storage and utilization of fine powders. Processes such as coagulation or flocculation are used to aid solid-fluid separation in dispersed particulate systems. Agglomeration also occurs as an accompaniment, often unwanted, to other particulate processing operations such as fine grinding, mixing and blending, transport and flow.Reliable agglomeration models are needed for improved understanding of the processes in general and of the complex role of numerous, interacting variables as well as for direct application to the design and control of industrial processes such as flocculation, granulation and pelletization. Ideally, the models should account for the primary forces responsible for agglomerate formation and growth, the effects of external forces on process dynamics, the development of agglomerate structure and its role in the process itself, and the effects of concurrent processes such as structure modification (e.g. compaction) and agglomerate breakage or degradation."

Jan 1, 1989

By D. A. Reynolds, J. D. Davis

During early development of the blast furnace, Connellsville coke made entirely from Pittsburgh-bed coal proved to be an excellent fuel. The need for blending coking coals arose as the industry grew and it became necessary to carbonize coals having voking properties inferior to those of Pittsburgh coal Most coals carbonized today in continental Europe and this country are blonded: This practise has improved the quality of coke and permitted the utilization of coals that would yield inferior coke, if carbonized sepa- rately, The depletion of the world's better coking coals, which has been noted by leading coal technologists,2/4/wes accelerated during the recent war and. It is important, therefore, that reserves be evaluated and conserved. In the principal, steel-producing sections of this country, Pocahontas coals have been blended so extensively that the terms "low-volatile coking coal": and. "Pocahontas" have become virtually synonymous. Other low-volatile coals. have been used to manufacture metallurgical coke and will be used more extensively as, the supply of the better known and more accessible Pocahontas coals decreases. Recognizing the need for augmenting the supply of high-rank coking coals, the Bureau of Mines has included both low- and medium-volatile coals in its Survey of the Carbonizing Properties of American Coals, which was started with the cooperation of the American Gas Association in 1929. Twenty coals, 12 of low-volatile and 8 of medium-volatile rank, have been blended with high-volatile A Pittsburgh-bed coal, and five standard low- volatile coals have been blended with various high-volatile coals. Most of the results of carbonization tests of these coals and their blends have been

May 1, 1946

By Nan C. Jensen, Oliver Bowles

Stone , the foundation of the continents and the floor of the oceans , is one of the most substantial and enduring of all substances that constitute the material universe . Stone furnished rude shelter for aboriginal man , and through all succeeding ages it has provided a lasting and serviceable structural material . Limestone is one of the most widely used building stones .

Oct 1, 1947

By M. S. Oudenhoven

This Bureau of Mines investigation was conducted to obtain an experimental solution of stress changes in the vicinity of a circular opening in an infinite plate. Plates were stressed biaxially in compression and subjected, by four different-length shoes, to a uniform pressure at opposing points on the opening periphery. The principal stresses along the vertical and horizontal axes, which result from peripheral pressure, were obtained from the photoelastic analysis of four frozen-stress epoxy models. These principal stresses were then super-imposed on the mathematically determined principal stresses (along the same axes) obtained from a theoretical biaxial stress field in which the magnitude of the lateral pressure was one-third that of the vertical pressure. The results indicate that an increase in shoe length increases the radial compressive stress and the tangential tensile stress (except tangential compression at r/a = 1, which exists for all shoe lengths). Also, a partial control of the stresses within one-half radius of the opening surface is accomplished by a change in the magnitude and placement of peripheral pressure.

Jan 1, 1966

By Edward J. Murphy

A comparative study has been made by the Bureau of Mines of several analytical methods for determining carbon monoxide and nitrogen oxides in toxic gases produced by the detonation of explosives. Laboratory and field methods and detector-tube devices are described. Analytical results are compared, and reliability of the various methods is discussed. INTRODUCTION In all underground mining there is ever-present danger to persons from possible overexposure to carbon monoxide and nitrogen oxides created by explosives or blasting agents. These health hazards, recognized for many years, led to the early establishment by the Bureau of Mines of specific requirements regarding fumes generated by explosives authorized for use in underground coal mines in the United States.3

Jan 1, 1961

By W. D. Ludemann, E. A. Loria, E. A. Rowe

The isothermal recrystallization of electrorefined vanadium has been studied as a function of annealing time , temperature , and prior deformation . Specimens were cold- rolled from 30- to 75 - percent reduction in thickness , then annealed from 700 ° to 1,200 ° C at time periods ranging from 1 minute to 96 hours . The course of recrystallization was followed by means of hardness , metallographic , and X- ray techniques , and a recrystallization diagram was constructed . Interpretation of the data indicated that there was around 50- percent softening due to recovery ( first stage of softening) before recrystallization began . The defining of recrystallization limits with respect to the amount of deformation was precisely established for electrorefined vanadium . More than 30- percent reduction was necessary for recrystallization to occur at 850 ° C. With 60- percent reduction , it was initiated at 750 ° C and completed at 950° C. The activation energy for recrystallization , as derived from the data , was 95,300 cal per mole for 60 - percent reduction and annealing at 750 ° to 900 ° C. Recrystallization by the mechanism of nucleation and growth was the principal process during the second stage of softening . minor part of the second stage of softening took place as strain- induced boundary migration , which was observed in specimens reduced 30 percent , bent in L- shape , and annealed at 950 ° C. Grain size decreased significantly only with the largest reductions and annealing between 750 ° and 950 ° C. Grain growth was expressed by the empirical relation D = KKtt"" ,, the exponent being the same at 60- percent reduction and annealing from 750 ° to 900 ° C. Accordingly , the activation energy for grain growth was 75,000 cal per mole .

Jan 1, 1964

By Albert L. Toenges

The development of Alaska depends on the existence of an adequate fuel supply in the Territory. The need to investigate coal deposits was recognized as early as 1911, when the first investigations were conducted in Alaska by engineers of the Bureau of Mines. Conditions existing in the Bering River and Matanuska coal fields, as found by Dr. Robert A. Holmes, former Director of the Bureau of Mines, are described by the Honorable W. L. Fisher, former Secretary of the Interior./ Following Dr. Holmes' investigation, a party of Bureau of Mines engi¬neers headed by R. Y. Williams visited the Bering River field in 1912 in cooperation with the Navy Department. A detailed examination was made of the Bering River field, and 855 tons of coal were mined from three prospects on Trout Creek. This bulk sample was delivered to the Navy for steaming and other tests. A description of the work of the field party and results of tests of the coal by the Navy Department and the Bureau of Mines has been published.

Jan 1, 1949

By Winthrop F. Watts

The U.S. Bureau of Mines evaluated the performance of a catalyzed diesel particulate filter (CDPF) and a CDPF combined with a diesel oxidation catalyst (DOC) at two metal mines. This report describes the results from the two field evaluations. The CDPF-DOC was installed on a load-haul-dump (LHD) powered by a 175-kW, prechambered, turbocharged engine. This system reduced diesel particulate matter (DPM) concentrations by 71±28 pet, as determined by size-selective sampling with gravimetric analysis, and by 71±29 pet, as determined by respirable combustible dust (RCD) analysis at the vehicle operator's location. The CDPF was installed on a diesel-hydraulic, roof-bolting jumbo, powered by a 172-kW engine. The CDPF reduced DPM concentrations by 72±21 pet, as determined by size-selective sampling with gravimetric analysis, and by 62±25 pet, as determined by RCD analysis at the vehicle operator's location. Underground evaluation was more difficult because of frequent movement by the roof-bolting jumbo, variation in daily workload, tremendous fluctuation in ventilation airflow rates, and use of a high sulfur diesel fuel, which promotes the formation of sulfate particles, decreases filtration efficiency, and hastens the deterioration of the catalyst.

Jan 1, 2010

By C. E. Wicks, F. E. Block, F. D. Stevenson

The vapor pressures of tungsten (VI ) chloride ( WC1 ) and hafnium ( IV ) iodide ( HFI ) were measured by a metal diaphragm technique . Vapor pressure values were obtained to permit calculation of the thermodynamic properties of the vaporization processes of the compounds . The vapor pressure data of WC16 are represented by the following equations for the liquid , B - solid , and a- solid over the temperature intervals indicated : - log P = 8.194 3,253 /T Liquid , 281.5 ° to 325 ° C : B - solid 230.0 ° to 281.5 ° C : log P a - solid 185.0 ° to 230.0 ° C : log Pam *** = 8.794 - 3,588 / T = 9.615 - 3,996 /T where T is the absolute temperature in degrees Kelvin . The heats of vaporization and sublimation are 14.9 , 16.4 , and 18.3 kcal / g mole , respectively . The entropy of vaporization at the normal boiling point , 330 ° C , was 24.3 eu . The fusion temperature , 281.5 ° C , and transition temperatures , 230.0 ° and 185 ° C , were found by thermal analysis .

Jan 1, 1964

By Albert F. Baker

Techniques were developed and circuitry was assembled for measuring the total and volume resistances to the flow of electric current through solid specimens of anthracite. The two-, three-, and four-terminal test methods demonstrated the extreme sensitivity of resistivity to differences in anthracite characteristics and showed response to changes resulting from variations in structure, temperature, and moisture content.

Jan 1, 1966