Search Documents

By Tracy. L. D.

"Since the introduction of pulverized coal as a substitute fuel for natural gas in the various types of heating furnaces used, in steel mills, a number of fires and explosions have occurred, resulting in the loss of life and property.As one of the primary functions of the Bureau of Mines is to conduct investigations in the utilization of mineral substances with a view to increasing safety in the use thereof, it was deemed advisable to investigate the hazards involved in the industrial use of pulverized coal and, if possible, to devise methods of preventing future accidents arising therefrom. The knowledge of the explosive qualities of coal dust which the Bureau has gained in studies affecting dust explosions in coal mines was of material assistance in these investigations.Several plants were visited in which either fires or explosions had occurred, and data obtained as to the probable cause of the accidents.There was found to exist, among some of those employed about the furnaces, a lack of knowledge of the explosive and inflammable qualities of powdered coal.A small stream of pulverized coal leaking down from a defective joint in a coal transport line did not attract much attention, whereas, had a leak in a natural gas line occurred -wider similar circumstances, no doubt it would have had immediate attention.As a matter of fact, if by any means the duet cloud should come in contact with an open flame or hot metal, the effects would be as disastrous as if it had been gas.This is exceedingly well illustrated by an accident which came to the writer's attention. In the system used at this particular plant, the pulverized coal is transported to the furnace through compressed-air lines. The fuel is fed from a storage bin to a blowing tank in quantities as desired, after which compressed air is admitted and the powdered coal blown to the furnaces. At the time of the accident some repairs were being made to the tank, and it was supposed that the air pressure had been entirely released as the pressure gage stood at zero. There was, however, one or two pounds air pressure remaining and when one of the connections was taken off, a cloud of dust was blown across the room, 30 or 40 feet towards the drier furnace where it came in contact with some live coals. Immediately the entire room was filled with flame which rolled back and forth over a specs 50 feet or so in length."

Apr 1, 1921

By Wilbert J. Huff

For the past 9 years , the technical studies conducted by the Explosives Division of this Bureau have been summarized in a series of reports issued annually . The following account presents investigations undertaken from July 1 , 1943 , to June 30 , 1944. The work is detailed under a number of main headings corresponding to the organizational structure of the Division , the various activities being under the immediate direction of unit chiefs , who report directly to the author . Specific credit , however , is due to the individual unit leader and his assistants .

Jan 1, 1945

By R. H. Reist, R. D. Dey, V. Castranova, J. P. Durham, Y. Rojanasakul

"Silicosis is a fibrotic pulmonary disease produced by inhalation of silica-containing dusts (Peters, 1986). Chronic silicosis may develop 20-40 years after initial exposure to crystalline silica, and the disease may progress from a simple to a complicated form. Few symptoms are evident in simple silicosis with pulmonary function being relatively normal. However, chest radiographs reveal small rounded ·opacities in the upper lobes of the lungs. These silicotic nodules consist of collagen arranged in a distinctive circular pattern. As fibrotic changes become more severe, the disease progresses to complicated silicosis (progressive massive fibrosis). Complicated silicosis is associated with shortness of breath and decreases in pulmonary function characteristic ofrestrictive lung disease. Chest x rays reveal numerous large silicotic nodules which may be associated with scar emphysema. Several mechanisms have been proposed to explain the cellular events which result in silica-induced lung damage and fibrosis (Lapp and Castranova, 1993). They include: ( l) direct cytotoxicity of silica, (2) activation of oxidant and enzyme release from alveolar macrophages, (3) recruitment and activation of polymorphonuclear leukocytes, and (4) stimulation of fibroblast proliferation and collagen synthesis.Tetrandrine is a bisbenzylisoquinoline alkaloid derived from the Chinese herb Radix Stephania tetrandra. It has a molecular weight of 622.73 and an empirical formula of C38H420 6N2. The chemical structure of tetrandrine has been published previously by our laboratory (Castranova et al., 1991 a). Its structure is characterized by methoxy groups at C7 and C12 , uncharged nitrogens at N2 and N’2 and two 17-carbon ring members connected by a double oxygen bridge between Ca-C7 and C11-C12. Tetrandrine has been shown to reduce both silica-induced fibrosis and the elevation of lung collagen content in rats (Huang et al .. 1981; Yu et al., 1983; ldel, 1987). Furthermore, tetrandrine has been used as an antifibrotic agent in Chinese clinical trials (Li et al.. 1981 ). Preliminary results suggest that administration of tetrandrine to patients with silicosis results in substantial improvement of symptoms, increases in diffusion capacity, and decreases in the size of shadows on lung x rays."

Nov 1, 1995

By H. C. Ko

Calorimetric determinations of low-temperature heat capacities and standard enthalpy of formation were made by the Federal Bureau of Mines for basic aluminum sulfite, A1203?2.0S02?5.3H20. The standard values of entropy (S°), enthalpy of formation (?Hf°), and calculated Gibbs energy of formation (?Gf°) at 298.15 K are 85.2±0.1 cal/deg-mole, -943.1±1.2 kcal/mole, and -820.7±1.2 kcal/mole, respectively.

Jan 1, 1976

By A. F. Baker

Laboratory flotation of synthetic coal-pyrite mixtures and high-pyritic-sulfur coal indicated that ferric chloride (FeCl3), aluminum chloride (AIC13), chromium chloride (CrCl3), and cupric sulfate (CuSO4) are potential pyrite depressants. For each metal salt there appeared to be a range of pH values and optimum concentration for selectively depressing pyrite in coal flotation. Pyrite was depressed in the pH range from 4.5 to 7.0 with ferric chloride, from 5.8 to 7.0 with aluminum chloride, from 6.4 to 7.1 with chromium chloride, and from 6.4 to 7.4 with cupric sulfate. Best separation of pyrite from coal was achieved in flotation solutions containing from 2 X 10-5 to 5 x 10-5 mole/ liter of each salt. In solutions containing excess salt concentrations, coal was also depressed. These Bureau of Mines tests demonstrated on a laboratory scale that, in solutions containing 4 X 10-5 mole/liter ferric chloride and from 1 x 10-4 to 2 x 10-4 mole/liter sodium hydroxide, the pyritic sulfur content of a Lower Freeport bed coal sample could be reduced from about 2.51 percent to less than 0.60 percent with recoveries of over 83 percent. The depression of pyrite appears to be due to the adsorption of positively charged colloidal metal hydroxide at the pyrite-solution interface. This hypothesis is supported by zeta potential determinations which showed that suspended coal and pyrite particles in solutions containing metal salts are positively charged in the pH range where depression occurs.

Jan 1, 1971

By E. P. Youngman

This paper is one of a series of digests of foreign minim legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the minim lams of Ceylon has been prey tired from the best available information in Washington and is released subject to amplification and correction, if necessary, by United States foreign-service officers. INTRODUCTION Ceylon has no basic mining law; the general rules governing the granting of mineral concessions and affecting legal titles of concessionaires are laid down in Ceylon Government ordinances or are found in the authorized forms for licenses and leases. The material available in the preparation of this digest is as follows:

Jan 1, 1933

By J. J. Forbes

First - aid training is an essential part of safety programs in the mining industry , but it is only a means to an end ; first -aid training will not eliminate accidents , but unquestionably it is of considerable value in any accident prevention program . Numerous features should be incorporated in any efficient , well - developed safety plan ; in addition to first -aid training safety work , to be reasonably effective , should include the establishment and maintenance of a safety organization , safety competitions between mines or sections of mines , safety- inspection committees , accident - investigation committees , safety meetings of mine officials , safety bulletins and posters , employees ' safety publications , Holmes Safety Chapters (which provide for monthly safety meetings of all employees ) , and numerous other activities looking to safe operation of mine or plant . These features are supplementary to the fundamentals of safety-- adequate and effective supervision and discipline . Years of experience , however , have demonstrated that first - aid training is a good accident -prevention auxiliary and should be made an integral part of every company's safety program . Many safety-organization plans have failed because they have been based upon the assumption that the supervisory force should be given full authority and responsibility for achieving safety and eliminating accidents and that the workers , who are most vitally concerned , are nonessential . First -aid training causes the employees to feel that they have a personal and full participation in the safety program and is now available so readily that no individual or organization has any valid excuse for not having it . Early investigations made with a view to bettering health and safety conditions among the employees in the mineral industries demonstrated the need of prompt care of injured employees because , under the difficulties inherent in the occupation , seemingly unimportant wounds , when not treated promptly, became infected and caused permanent disability and even death . Many seriously injured persons , brought out of mines and plants by fellow workers who were ignorant of the approved methods of giving first aid or of safe means of transportation

Aug 1, 1934

By Donald S. Colby

CARBON-BLACK shipments, which had declined in the latter art of 1953, remained low in 1954 until after settlement of the labor strike that occurred in the rubber industry in July and August. The production of new model automobiles in the last quarter of the year spurred the demand for rubber tires and consequently the demand for carbon black. Total shipments of 1,498 million pounds for the year were 4 percent below 1953.

Jan 1, 1958

By L. D. Tracy

"IntroductionOne of the problems which the coal-mining industry must solve in the next few years is the redaction of its ever-increasing timber bill. This includes pit posts, mine tees, timber sets, and brattice boards. As an example of this increase, the following table of timber prices from the records of a coal company in western Pennsylvania, in a district where the supply of most of the different kinds of timber used can be shipped from points within the State, is self-explanatory: Present conditions seem to indicate the continued upward trend ox the cost of mine timber, although the regrettable calamity that has visited the chestnut timber in Pennsylvania may temporarily hold the price of some types of mine timber on a level basis. On account of the chestnut blight, many farmers will undoubtedly begin to convert their chestnut trees into timber before they become a total loss. This may provide, for the time being, a sufficient supply of mine timber to check the steadily rising prices.The local lumber producers are turning their attention to the production of the larger sizes of timber and lumber on account of an unfavorable price on mine ties. From the foregoing table, it is seen that the average advance in the price of ties during the period 1914 to 1920 is 52 per cent, while timber sets and mine car plank increased in value 60 per cent. Amore striking illustration is the fact that a 6 by 8 inch by 6 foot tie sells for 42 cents or at the rate of $17.50 per 1000 board feet; yet mine car plank and timber sets have a value of $48 per 1000 feet, an advantage of $30.50 in favor of the heavier timber.The supply of coal in Western and Central Pennsylvania will last for a long period and it is for the possible future demand for timber that the coal companies must provide. While steel, concrete, and other materials may, in many cases, prove an acceptable substitute, there is no doubt that timber will always be in demand."

Nov 1, 1926

By Harry W. Campbell

During 1983, the U.S. Bureau of Mines conducted a mineral survey of 19,700 acres that included the Fish Creek Mountains WSA (Wilderness Study Area), 15 miles southwest of the Salton Sea. Two United States Gypsum Co. claim groups in the WSA have more than .20 million tons of inferred gypsum reserves. These high-grade, surface and near-surface gypsum deposits are an extension of a gypsum bed that has been mined continuously since 1922. The Waters prospect in the central part of the WSA has large quantities of limestone suitable for many commercial uses. Sand and gravel is plentiful in the WSA in alluvial fan and ancient shore-line deposits. Limestone and alluvial deposits are not economic because similar material is closer to potential markets. No evidence of energy minerals or geothermal resources was identified in the WSA. A portion of the eastern Fish Creek Mountains WSA is leased for oil and gas exploration. United States Gypsum Co. holds eighteen unpatented placer claims in the northwestern part of the WSA. No other mining claims or mineral leases were identified in the study area. No mineral production is known from within the WSA.

Jan 1, 1986

By Maust. E. J., W. R. Crane

"IntroductionIn the study of mine drainage in the red iron ore mines of the Birmingham district of Alabama, an extensive series of measurements were made in order to determine the drainage from the area overlying and adjacent to the mines. Gaging rods were generally used in measuring streams, and weirs in ditches and sometimes as a check on rod work. These tests in turn were checked by current meter tests. In all, 725 separate stream gagings and 97 weir measurements were made. Certain relationships were worked out, particularly between rod and weir tests, which permitted obtaining results that are much more accurate 'under the existing conditions, than any available formula would give. The large number of weir measurements and the period covered by the tests made it impracticable to construct a weir for each observation so portable, adjustable weirs were built. The methods used are described here for the benefit of those interested in measurement of streams in connection with a study of mine drainage or otherwise. The Drainage AreaThe area draining the mining district lies between the crest of Red Mountain and Little Shades Creek, and for convenience was divided into sub-districts adjacent to certain groups of mines. Gaging stations were established on Little Shades Creek at the upper and lower boundaries of each sub-district, also at points on the tributaries near their junction with the creek. The difference between the volumes of water flowing in Little Shades Creek as it entered and left the sub-districts represents the flow from the tributaries on both sides of the creek. Since the flow coming from the sub-districts was measured direct, the inflow from the tributaries on the opposite side of the creek can be computed from the three volumes determined."

Oct 1, 1926

By Janet Torma-Krajewski, Pauline Lewis, Paul Gust, Lisa Steiner, Kean Johnson

Ergonomics processes described in the literature have been associated mostly with manufacturing, financial, electronics, and office settings where working conditions tend to be rather constant and repetitive. The information presented in this document demonstrates, however, that an ergonomics process can also be implemented in a setting such as mining where working conditions frequently change and workers are periodically exposed to extreme weather conditions. This document describes how Bridger Coal Company implemented an ergonomics process at its Jim Bridger Mine from 2001 through 2004. The process developed by the Ergonomics Committee, the promotion of the process to management and employees, and the impacts of the process on working conditions at the mine are reviewed. Barriers overcome and lessons learned are also described. Quotes from Bridger Coal Company employees are included in the document to add a personal perspective. Other industries with working conditions similar to mining, such as construction and agriculture, may find this information useful.

Jan 9, 2006

By E. J. Gleim

This report describes a trip to Europe in the interest of safety in coal mines. It reviews the Eighth International Conference of Directors of Safety in Mines Re-search, which met in Dortmund-Derne, Germany, July 5-10, 1954, to discuss results of studies made in different countries to improve health and safety conditions under-ground. It also summarizes information on subjects of special interest in the United States gained by the writer in visits to mining experiment stations in Belgium, France, and England. The efforts being made to protect life and property underground were discussed, and ideas and experiences were interchanged freely, not only during the conference but also during visits to the several countries. Helpful information was obtained on many topics of interest, but time did not permit as thorough a discussion on some of them as might be desired.

Jan 1, 1956

By R. R. Sayers, W. J. McConnell

"The health, comfort, and efficiency of men engaged in the mining industry may be impaired, in some instances very seriously, by abnormal physical conditions of the mine air or by variations in its composition. This is true in some of sheet metal mines of the West where high temperatures with varying humidities are encountered. Physiological studies have been made in some of these mines showing the effects of various temperatures end humidities. As it is difficult to carry out studies on many controlled temperatures, it was thought best to make the experiments in a laboratory and apply the results to the industry insofar as practicableThe effects of moderately high temperatures and humidities are more difficult to measure perhaps than the extreme conditions, but may be predisposing causes of fatigue, discomfort and disease, A cooperative study of the physioloical effects of heat and humidity is being conducted by the Bureau of Mines and the U. S. Public Health Service cooperative with the American Society of Heating and Ventilating Engineers, in the Research Laboratory of the Bureau of Mines at Pittsburgh, Pa."

Mar 1, 1924

By John Durkin

A computer model has been generated to evaluate speech intelligibility of individuals wearing conventional and electronic hearing protectors. For speakers talking at normal levels in noise levels of 65 db(Lp) or less, it was found that conventional hearing protectors significantly reduced speech intelligibility. Under the same conditions, electronic protectors provided scores equal to those for the unprotected individuals while providing protection from high noise levels. Therefore, electronic hearing protection is valuable in areas where high noise level is intermittent.

Jan 1, 1979

By George L. Gates

The Bureau of Mines studied pressure-buildup data from a number of California gas wells to determine if the reservoir properties calculated from these data correlated with field-observed reservoir properties. Pressure-buildup curves from 24 wells showed distinct changes in slope, indicating changes in permeability of the reservoir rock. Calculated distances from the wells to indicated permeability changes were in fair agreement with distances deter-mined in the field. Pressure-buildup curves from three wells had more than one distinct change in slope, indicating multiple permeability changes. Thus field data supported the theoretical relations used to calculate reservoir properties from pressure-time relations measured in gas wells.

Jan 1, 1967

By Debra A. Griffith

The U.S. Bureau of Mines currently is researching the relationship between the level of back strength and the probability of low-back injury. This report is a review of the literature and statistics on over-exertion injuries. Overexertion continues to be a significant source of injury in metal and nonmetal mining, accounting for approximately 24 pct of all injuries yearly. These injuries, particularly to the lower back, can be very expensive in human and monetary terms. An examination of the accident data on overexertion injuries is necessary to provide a background for research into prevention and/or amelioration of those in-juries. The job categories outlined in the Accident Data Analysis data base most affected are "Mechanic/Electrician" and "Mill/Plant Worker." The age group most affected is "30-39" years, and the experience group most affected is "0-.99" years. The most prevalent type of overexertion injury is "Strain/Sprain," and the trunk is the body part most often involved in an overexertion injury.

Jan 1, 1994

By Martin Hertzberg

The concept of limit burning velocities, formulated in an earlier Bureau of Mines report (RI 8127), is applied to the problem of flame propagation through tubes of finite size. The limit burning velocity for conductive-convective wall-loss quenching (process b) is (Su)b = [aPe,] where the proper choice of critical Peclet constant, Pe, is determined mainly by the ratio of contact-perimeter loss area to flame-zone cross sectional area. This ratio of loss area to propagation area relates to the shape of the flame front and its control by buoyancy and by boundary conditions. The comparison of (Su)b with previously defined limit velocities for systems mixed by natural convection allows one to assess the influence of tube dimensions and boundary constraints on the "true" or earthly limits for the three directions of propagation. The flame quenching caused by inert powders is shown to be similarly described in terms of a limit burning velocity, (Su)?b. The tube's surface-to-volume ratio (~1/ro) is simply replaced by the powder's surface area per unit volume of the flammable mixture. Thermal loss quenching by these "internal walls" occurs at a critical Peclet constant somewhat higher than that observed for tubes, and the problem is complicated by the finite heat capacities of the powders and particle lag effects in the flame front.

Jan 1, 1980

The Bureau of Mines has long been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts, the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions1 issued by the Bureau of Mines, and the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. The Government, with the exception of the Tennessee Valley Authority, purchased approximately 5.5 million tons of coal in fiscal year 1971. In connection with these purchases, the Bureau analyzed 4,366 samples. These are published (table 1) for the use of Government officials and the public. Such analyses of delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1972

By M. V. Potter

"In nearly all fields of investigation, research laboratories and routine testing laboratories encounter problems in which the primary determinations involved in the study require the measurement of mechanical vibrations or motions. These vibrations,may be of an oscillatory nature covering frequencies from a few cycles per second up to hundreds of Kilocycles per second, or they may be more or less uniform study nations occurring at rather slow rates. In electrical, or mechanical methods. In the optical case the to cause the deflection of a light beam such that the motion of the mechanican system of the beam can be determined, then by direct the by direct observation on a suitable scale or by recording it’s the electrical methods the motions can be made to changes in resistance, capacity or inductance proportion to the mechanical displacement or electromagnetic means can used to generate directly a voltage that will be porpertuial to the instantaneous vicinity of the vibrations. Other devices are used in a special instance, also but in any cause the electrical methods produce a current that is an electrical counterpart of the mechanical motion, and the motion can then be studied by direct measurements of the current or by recording the current on suitable recording meters or oscillography. Mechanical methods are used in some instance but are generally not as convenient nor as flexible as the optical and electrical methods."

Feb 1, 1943