Search Documents

By John P. Gooch

The solubility of 1,1,2,2-tetrabromoethane (TBE) in water was determined from 1.0° to 97.0° C. The solubility (S) of TBE in grams of solute per 100 grams water was correlated with [S = 1,920.55 [exp (40292L7 11, T2 10 T 737.577 + 9.923962 ] where T is in degrees Kelvin. A thermodynamic analysis conducted on a system consisting of a TBE phase and a water phase in equilibrium with a vapor phase led to the calculation of the activity coefficient, vapor-liquid equilibrium distribution coefficient, relative volatility, and heat of mixing for saturated solutions of TBE in water. Data required for these calculations were the solubility of TBE in water and the vapor pressures of TBE and water as a function of temperature.

Jan 1, 1972

By David C. Oyler

Methane-drainage holes must be completely filled by grout before mining to prevent the emission of large quantities of gas during mine-through, which would constitute an explosion hazard. In November 1980, seven horizontal holes at the multipurpose borehole, a small-diameter shaft drilled as a Bureau of Mines coalbed methane-drainage installation on the property of the Federal No. 2 Mine, Monongalia County, WV, were plugged using a sodium silicate gel grout. This report de- scribes the grout mix and the use of the grout at the multipurpose borehole, and discusses the results observed upon mine-through of the holes in early 1981. Cost data for the sodium silicate grout are also presented.

Jan 1, 1984

By E. G. King

Existing thermodynamic data for compounds of the rare-earth metals are few in number and often inaccurate because, in the past, it was difficult to obtain samples that were pure enough and reasonable in cost--a situation that is rapidly improving. This paper reports the results of low-temperature heat-capacity and high-temperature heat-content measurements for cerous fluoride (CeF3) and supplies the first such published data for a rare-earth fluoride. The low-temperature heat-capacity data cover the temperature range 51°-298° K. and serve to evaluate the entropy at 298.15° K. The high-temperature heat-content data cover the temperature range 298°-1,799° K., including the temperature and heat of fusion. The results are assembled for ready use in thermodynamic calculations. Cerous fluoride is one of the important intermediate compounds in the production of cerium metal.

Jan 1, 1959

By D. N. Tallman

The electrokinetic properties of MgO have been utilized to simultaneously filter suspended solids and remove trace amounts of dissolved heavy metals from synthetic mine water. Greater than 95 pct removal of metals from influent at neutral pH containing 1 to 6 mg/L of dissolved Cd, Cu, Mn, Ni, and Zn can be routinely achieved by filtering through a granular bed of MgO at flow rates typical of rapid sand filtration (0.3 cm/s). Filtrate concentrations of most metals can be maintained below 0.1 mg/L for 160 bed volumes or more loading. The more mobile metals (those with larger solubility products) are more difficult to remove, and are strongly bonded to the MgO granules so that chemical stripping with chelating agent is required to clean the bed. Less mobile ions are easily removed by the filter and are effectively stripped by conventional filter backwashing. The fraction of metals recovered by chemically stripping the loaded MgO filters correlates to the zero points of charge of the metals. This process may be applicable to removal and recovery of trace amounts of heavy metals in mine drainage that is partly neutralized by liming. Also, since many of these metals are critical and strategic, the technique can be adapted not only to recycle process water from mineral and milling waste streams, but also to reclaim their metal values.

Jan 1, 1986

By ALICE V. Petar

Thallium is one of the rare metals that has come into commercial use within recent years . Its comparative scarcity , combined with a resemblance to the common metal lead , have retarded the development of uses for thallium . Although production is still measured in pounds rather than in tons , it is now finding application in a number of fields . Perhaps the earliest commercial use of thallium was as a constituent of optical glass of higher refractive power than similar glasses containing lead . One of the later applications to attract attention was the use of the oxysulphide in a sensitive electrical device similar to the selenium cell . The " Thalofide " cell , which was patented in 1919 , constituted for a time the most important outlet for thallium. During the next few years the limited use of thallium and its salts in other fields was insufficient to absorb an annual production of a few hundred pounds , and the price dropped from $ 16 or $18 per pound in 1922 to $ 5 per pound in 1924 . Beginning in 1925 several new uses were developed , especially as a poison for rodents and ants , and as a result the demand for thallium increased sufficiently to cause a recovery in price to the present level of from $12 to $15 per pound .

Jun 1, 1931

By L. A. Haas

The Bureau of Mines conducted bench-scale leaching tests with recycled spent copper electrolytes and copper-nickel mattes produced from the Minnesota Duluth Complex concentrates. This report describes the first stage of an overall two-stage leach operation. The objective of this research was to determine the matte-leach technology required to convert spent copper electrolyte into an enriched nickel liquor suitable for a nickel refinery and there-fore essentially free of copper, iron, and sulfuric acid. The experimental variables investigated were matte composition, particle size, spent electrolyte content, pulp concentration, oxygenation, temperature, and time. The time required to produce an enriched purified nickel liquor decreased with increasing pulp concentration, temperature, and oxygenation, but increased with increasing particle size and electrolyte copper and acid content. Nickel-rich (about 50 g/l) liquors at a pH of about 4 and containing less than 1 g/l of copper and iron were produced at 70° C by leaching minus 325-mesh low-iron (less than 5 pct) matte for 8 hours with spent electrolyte containing 22.4 g/l Cu, 28.9 g/l Ni, less than 0.1 g/l Fe, and 50 g/l H2S04 at a pulp concentration of 1 kg of matte per liter of spent electrolyteo Varying the nickel content of the spent electrolyte from 11 to 101 g/l appeared to have no appreciable influence on the matte leaching characteristics.

Jan 1, 1981

By H. L. Riley

This report describes the methods and equipment used by the Watauga Stone Co. to drill und blast limestone in a two-level quarry, and to crush, screen, blend, and load this stone. Power requirements per ton of stone produced are reported. The personnel requirements for individual phases of the operation are tabulated in man-hours per ton of stone produced.

Jan 1, 1963

By G. G. Campbell

The Bureau of Mines in cooperation with Quaker State Refining Corp. conducted two underground-combustion oil-recovery experiments in the Venango Second sandstone in the Reno pool, Foster-Rena-Oil City field, Sugar Creek Township) Venango County, Pa.) to determine the applicability of the process for reservoirs producing Pennsylvania-grade paraffin-base crude oil. Tests were terminated when analyses of produced gas showed that a self-sustaining combustion front did not exist. It was thought that insufficient fuel had been deposited in the formation. Laboratory retort tests made after the second field test was concluded showed that crude oil from the Reno area would deposit enough fuel to support combustion if air flux, temperature, and time were maintained within defined limits.

Jan 1, 1967

By James Noll

Total carbon (TC) is sometimes used to measure or characterize diesel particulate matter (DPM) in occupational settings such as underground mines. DPM samples are collected on quartz fiber filters. When using quartz fiber ?lters, adsorption of gas phase organic carbon (OC) has been reported, causing a positive bias in the particulate TC results (adsorption artifact). Most of the data on the sampling artifacts and corrections apply to environmental air sampling, where samples are collected at a much higher filter face velocity and the OC concentrations are generally much lower relative to occupational sampling. In this study, we investigated the effects of adsorption artifact on samples from occupational settings. Samples were collected with and without denuders to determine the amount of gas phase OC collected and the accuracy of certain corrections. In underground stone mines, the adsorption artifact was found to positively bias the particulate TC by greater than 20% for filter loadings below 25 µg/cm2 TC (8-h time weighted average) 262 µg/m3). The tandem ?lter correction reduced the effect of the artifact, as high as 60% of the TC value, to less than 11% for laboratory data. It also significantly reduced the effect of the artifact obtained for field samples.

Jan 1, 2008

By Lawrence W. Sott

This Bureau of Mines report presents several factors that currently enter into the design, manufacture, and testing of windows and lenses used in explosion-proof enclosures. Emphasis is also given to the sealing concepts for lenses. Criteria for adhesives and sealants are suggested based on the survivability of an explosion-proof enclosure as a structure, rather than upon the minimum material properties of its constituents. Procedures for surface preparation of adherends are also discussed.

Jan 1, 1982

By Liming Yuan

A computational fluid dynamics (CFD) study was conducted to model effects of coal properties on the potential for spontaneous heating in longwall gob (mined out) areas. A two longwall panel district using a bleeder ventilation system was simulated. The permeability and porosity profiles for the longwall gob were generated from a geotechnical model and were used as inputs for the three dimensional CFD modeling. The spontaneous heating is modeled as the low temperature oxidation of coal in the gob using kinetic data obtained from previous laboratory scale spontaneous combustion studies. Heat generated from coal oxidation is dissipated by convection and conduction, while oxygen and oxidation products are transported by convection and diffusion. Unsteady state simulations were conducted for three different US coals and simulation results were compared with some available test results. The effects of coal surface area and heat of reaction on the spontaneous heating process were also examined.

Jan 1, 2008

By Raymond W. Hiteshue, Sam Friedman, Martin D. Schlesinger

The Bureau of Mines in cooperation with the El Paso Natural Gas Co. investigated the effect of high temperature and pressure at short residence times on the hydrogenation of a New Mexico coal to gaseous and liquid hydrocarbons . The study was made in a bench - scale semicontinuous unit at pressures of 500 to 6,000 psig , 480 ° to 1,000 ° C , and residence times of less than 1 minute to 15 minutes . Ammonium heptamolybdate was impregnated on the coal to furnish 1 percent molybdenum based on maf coal . Coal could be rapidly hydrogenated at elevated temperatures and pressures to yield large quantities of gaseous hydrocarbons and small quantities of lowboiling oils , high in single - ring aromatics . At 800 ° C and 6,000 psig and a residence time of 1 minute , the yield of hydrocarbon gas was 43 percent and of liquid hydrocarbons 9 percent , based on maf coal . With a 15 - minute residence time , the yield of gaseous hydrocarbons increased to 68 percent with a decrease in yield of oil to 6 percent . At higher hydrogen velocities , the yields of oil were much greater but contained large quantities of asphaltene . Low concentrations of molybdenum (0.01 and 0.1 percent ) or a high concentration of iron ( 1 percent ) were ineffective at 800 ° C , 6,000 psig , and short residence time .

Jan 1, 1964

By Jr. Norman

The Bureau of Mines investigated the thermoelectric properties of yttrium selenides and tellurides from room temperature to 900° C. X-ray crystallographic data were determined for the yttrium-selenium and yttrium-tellurium compounds that were orthorhombic with a cubic substructure. The yttrium selenides and tellurides exhibited semimetallic to insulator conduction properties with figures of merit of 10-9 to 10-4 °C-1. The mono-selenide and monotelluride behavior was partially degenerate; unsatisfied bonds were the source of the large number of charge carriers. The higher stoichiometry selenide compounds were intrinsic semiconductors) but with high electrical resistivities. A critical defect or impurity ionization energy for carrier activation appeared to exist in the majority of telluride compounds. Mobility and energy band determinations are required to interpret completely the observed effects in most of the compounds studied.

Jan 1, 1966

By Frank A. Peters

The Bayer process treating Jamaican bauxite was evaluated from an economic standpoint, using standard estimating methods and published data, to present a reference point for cost estimates for nonbauxite alumina processes. The estimated operating cost for a plant producing 1,000 tons of alumina a day is $47.96 per ton of alumina when charging $8 per ton for bauxite and $2.30 per hour for direct labor. The estimated fixed capital cost is $46 million.

Jan 1, 1966

By B. H. Eccleston

Experimental data were obtained from two medium-duty diesel engines derated to qualify for use in underground mines. Gaseous and particulate emissions from these engines were measured and results provide information on the effect of exhaust treatment devices on the emissions. The devices in the study were a catalyst, a particulate trap, and an exhaust gas cooler of the water scrubber type. Emission levels of carbon monoxide and hydrocarbons were observed to be very low in comparison with emission levels of comparable engines in full-rated operation. Oxides of nitrogen and benzo(a)pyrene content of the exhaust also were found to be somewhat low in comparison with previous findings. For particulate reduction, the combination of a particulate trap and a scrubber was observed to be the most effective combination tried; in some cases, over 60 pct particulate reduction was effected by the trap-scrubber combination.

Jan 1, 1981

By J. G. Stuart, A. W. Cipkins, R. H. Thompson

Preliminary safe distances for blasting wiring from typical electromagnetic sources are presented. The distances are for underground coal mines and electromagnetic sources in the frequency range below 10 MHz. The distances are based on measurements performed at 3 locations in each of 3 coal mines. The measurement apparatus, measurement procedure, measurement results and the rationale used in the calculation of the safe distances are all described. The safe distances presented are dependent on the measurement results and their interpretation. More measurements are clearly necessary to establish the validity of the suggested distances.

Jan 1, 1985

By Robert C. Dyni

The use of techniques and equipment designed to pneumatically place backfill into an underground mine opening through boreholes for subsidence abatement has historically met with limited success, largely due to the inability to directly monitor the placement of the backfill in the opening. The success of a backfilling project cannot be guaranteed if it is not known whether the underground opening has been completely filled with backfill material. To overcome the inability to directly monitor backfill placement, the U.S. Bureau of Mines developed a pneumatic backfilling system that allows for direct viewing of the backfill as it is placed in an underground mine opening. This system utilizes a recently developed pneumatic nozzle coupled with an instrumentation package that allows for real-time observations and measurements of backfill placed in an underground opening through a borehole. The nozzle utilizes a high-velocity airstream to redirect backfill falling through a pipe in the borehole and directly in front of the nozzle; the airstream redirects and propels the backfill horizontally into the .mine opening at over 100 ft/s. The instrumentation package, mounted directly to the nozzle, contains a video camera, high-intensity lamps, laser-rangefinder, electronic compass, and water sensor.

Jan 1, 2010

By Byron S. Gottfried

This Bureau of Mines report presents a method for combining the distribution curves at different specific gravities of separation, for a given piece of coal-cleaning equipment and a given raw coal feed, into a single, generalized distribution curve normalized with respect to specific gravity and, therefore, independent of the specific gravity of separation. Illustrative generalized distribution curves, based upon Bureau of Mines collected data on industrial operations, are presented for five different types of coal-cleaning equipment. The well-known concept of probable error is extended to the generalized distribution curve. It is shown that the conventional probable error is directly proportional to the specific gravity of separation. A number of sample calculations, illustrating the use of the generalized distribution curve and generalized probable error, are presented in the appendix.

Jan 1, 1977

By P. G. Bennett

The Bureau of Mines developed a process using ion exchange to recover cobalt from spent copper leach solutions. A preliminary economic evaluation of the process indicated that about one-third of the capital cost was attributed to the total resin inventory, and one-third of the operating cost was required for reagents to remove iron from the ion-exchange eluates. An agitated Pachuca elution system was investigated in place of a fixed-bed elution system. The Pachuca system reduced the resin inventory by 27 pet when compared with the fixed-bed elution system. Processing fresh spent copper leach solution reduced the resin inventory by 20 pct and resin iron loading by 80 pct. Reagent requirements for removing iron from the eluates were decreased because less iron was extracted. The Pachuca system, along with processing fresh spent copper leach solution, reduced the total resin inventory by 47 pct. A revised cost evaluation of the cobalt recovery process was obtained to determine the effects of these process modifIcations. The estimated total capital cost for a plant processing 10,000 gpm of spent copper leach solution containing 26 ppm Co was $23.1 million. With credits for nickel, zinc, and copper byproducts, the estimated net operating cost was $5.10/lb of cobalt.

Jan 1, 1988

By Synthia N. McIntosh

The U.S. Bureau of Mines investigated the feasibility of using ammonium carbamate (NH2CO2NH4) leaching to recover manganese from steel plant slag. This investigation showed that treatment of the slag in hydrogen prior to leaching enhanced manganese extraction. Up to 80 pct of the manganese and 50 pct of the iron could be extracted from a silicon steel slag that had been pretreated in hydrogen at 700° C. Two 4-h leaching stages conducted at ambient temperature with a solution containing ammonia and carbon dioxide dissolved manganese and iron as their carbamate complexes. Heating the pregnant solution to 65° to 85° C decomposed the complexes and precipitated the metals as insoluble carbonate salts. Ammonium carbamate leaching of other slags from several steelmaking plants produced lower manganese extractions, which suggests that the method cannot be applied satisfactorily to all steelmaking slags

Jan 1, 2010