Search Documents

By Thomas P. Mucho

Retreat or pillar recovery mining redistributes the overburden weight onto the adjacent coal pillars in a room-and-pillar section. The additional stress and the resultant energy stored in the remaining pillars can become so great that pillars may bump or violently fail. An investigation at the Gary No.2 Mine was conducted to examine the effectiveness of the thin pillar mining method for mitigating bump occurrences. Field observations were made and instruments were installed to monitor pillar behavior during extraction. Stress monitoring instruments and roof-to-floor convergence stations were installed in pillars and entries and crosscuts, respectively. Results indicated that high pillar stress concentrations occurred in these bump-prone geologic conditions. The thin pillar mechanism, the creation and progressive outby movement of an expanded yield zone, was also monitored through the instruments. The expanded yield zone, a result of using thin pillars in a highly stressed pillar line area, mitigates bump risk.

Jan 1, 2010

By Harold E. Marr

Energy dispersion X-ray analysis was evaluated for possible application in the secondary metals industries for the rapid analysis and identification of copper-base alloys. Laboratory investigations of standard brass and bronze samples indicate that X-ray methods are capable of separating standard alloys into 10 general classes with analytical times of less than 3 seconds per sample for clean, flat samples. A radioactive source of americium 241 with a secondary fluorescer was used as an excitation source, and a lithium-drifted silicon semiconductor detector was utilized for energy discrimination of X-rays.

Jan 1, 1974

By Henry M. Harris, Hal J. Kelly

Electrical dewatering tests are described in which the laboratory cells were designed for continuous operation using an endless metal belt as the anode . The test slurries were dilute , containing from 2.5 to 14.4 percent solids (specific gravity of 1.02 to 1.10 ) that were all minus 8 microns in size . Recovery of the solids of low water content was the practical objective of the investigation . Process variables evaluated and reported are : The effect of feed rate , amount of electrolyte , samples from different sources , and the use of two cells in series . These variables are evaluated on the basis of yield of clay per kilowatt - hour , recovery , and the amount of solids in the deposited clay . Recovery , yield , and solid content of the belt anode product are interdependent , and changes that will improve one of these characteristics often are accomplished at the expense of the others . Tests in which recoveries range from 50 to 60 percent usually result in yields of 8 to 9 kilograms (kg ) of dry clay per kilowatt- hour (kwhr ) . Under these conditions , the solid content of the deposited clay approximates 50 percent . One test sample , composed of kaolinite , showed very high yield , 13 to 16 kg per kwhr ; high recovery , 53 to 58 percent ; and 52 to 54 percent solids in the cake .

Jan 1, 1964

By A. L. Engel

This investigation was undertaken to assess the feasibility of processing an extensive deposit of iron ore near Palisades, Eureka County, Nev., previously penalized for high phosphorus content. The experiments described indicate a satisfactory accomplishment of objective. Chemical treatment will permit a high-phosphorus iron ore to be used. Leaching with acid solution effectively lowers the phosphorus content with a [gligible] loss of iron. The use of hydrochloric acid is preferred because [ ] does not contaminate the ore and the cost is lower. Minus-1/2-inch ore was satisfactorily leached in 24 hours, minus-1/4-inch ore, in 8 hours, and minus-10-mesh ore, in 3 hours. About 40 pounds of acid per ton of ore was consumed in each instance.

Jan 1, 1959

By J. L. Shultz

The Bureau of Mines extended its investigation of methanation catalysts. The noble metals (platinum, palladium, ruthenium, rhodium, osmium) and rhenium), molybdenum, and tungsten were tested in hydrogenations of carbon monoxide and carbon dioxide at 21 atmospheres in a temperature range between 200° and 600° C. From the 8 metals studied) 25 catalysts represent 5 catalyst types were prepared and tested. The impregnated 0.5-percent-ruthenium catalyst proved to be the most active and versatile of all the catalysts produced. Tungsten and the noble metals other than ruthenium were low in activity and usually required temperatures above 500° C for appreciable production of hydrocarbons. Molybdenum was moderate in activity, but further improvement in molybdenum catalysts seems possible.

Jan 1, 1967

By F. E. Armstrong

Tritiated water has been used as a tracer to follow the path of leach liquids as they flow through a copper-mine dump. Semipermeable layers, produced within the dump by compaction and "stratification" of deposized dump material, restrict the vertical movement of water. Knowledge of this restriction would aid in the optimization of the leaching process. The portion of the dump of particular interest was approximately 2,000 feet long, 800 feet wide, and 200 feet high. A total of 94 curies of tritiated water was injected into the dump at the rate of 650 gpm over a period of 39 hours. The leach liquid was sampled at natural surface outflows and through a series of wells, some drilled to the bottom of the dump and others to intermediate levels. More than 3,300 samples were analyzed, most by liquid scintillation counting, but a few hundred by gas counting. Data obtained permitted calculation of flow paths, recycle times, total fluid volume, and estimates of retention times in various portions of the dump.

Jan 1, 1971

By Benjamin W. Haynes

The Bureau of Mines, in cooperation with the National Oceanic and Atmospheric Administration (NOAA), has updated a 1977 NOAA report prepared by Dames & Moore entitled, "Description of Manganese Nodule Processing Activities for Environmental Studies." This updated report contains detailed flowsheets and descriptions of the five potential first-generation nodule recovery schemes now considered most likely to be used by industry; they are high-temperature gas reduction and ammoniacal leach, Cuprion ammoniacal leach, high-temperature and high-pressure H2S04 leach, reduction and HCI leach, and smelting and H2S04 leach. The first three processes are three-metal recovery schemes (Cu, Ni, and Co) with the option of Mn recovery from the tailings. The remaining two processes are four-metal (Cu, Ni, Co, and Mn) recovery schemes. All except the HCI process are assumed to use a nodule feed rate of 3 million tons per year (dry basis). Final metal products are Co powder and cathode Cu and Ni. A minor amount of Ni is also recovered as powder, and some Cu and Zn are recovered as mixed sulfides. Manganese in the four-metal processes is recovered as either manganese metal or ferromanganese.

Jan 1, 1983

By John P. Walsted

Because of the absence of an iron-producing industry, the Pacific Northwest is working under an economic handicap. This is particularly apparent in the gray-iron-foundry industry because of the high price of pig iron imported from foreign sources or shipped in from producing ?areas within the United States. The high prices and sometimes short supply of ferrous metal products has put a brake on industrialization, which has been only partly compensated by the availability of cheap electric power. The economic condition of the gray-iron-foundry industry could be improved by establishing a small iron-producing industry based on the locally available ores. Moreover, establishing a local iron smelter would create a market for resources now dormant. Low-grade ores of manganese, chromium, and nickel would become usable in industry when combined with the iron ore from Scappoose. Pig iron produced in even limited quantities would level out the fluctuation in supply. The ore deposits, being small, would not supply enough pig iron to satisfy the entire demand. This condition necessitates designing special pig irons that will carry abnormally high proportions of scrap in the cupola charge.

Jan 1, 1955

By C. R. McCann

The Bureau of Mines conducted an experimental study of conditions needed to produce flames of pulverized coal when the heat needed for ignition is sup-plied only from the flame and hot furnace refractory. An electrically heated furnace which burned about 1 pound of coal per hour was designed and fabricated. A sheath of air, surrounding the primary coal and air stream, was used to prevent entry of hot gases from recirculating combustion products. Furnace temperatures needed for ignition ranged from about 1,8300 F for an Illinois coal to 2,250° F for a Beckley seam coal. Apparent flame velocities were about 2 to 5 feet per second, increasing with volatile content of the coal and with distance from the burner mouth to the flame. The time required for ignition, approximately 0.02 to 0.07 sec, was a better measure of flame behavior than was velocity.

Jan 1, 1969

By A. J. Forney

Recent experiments used catalysts of plate assemblies in synthesizing high-Btu gas and gasoline indirectly from coal. A gas with a heating value of 925 to 943 Bt-: per cubic foot has been prod u la the hot-gas-recycle pilot plant from synthesis gas (3H2+100) with lathe turnings used as catalyst in the first reactor, and assemblies of parallel sprayed plats of nickel in the second. Solid plates made of Raney nickel, and steel and aluminum plates sprayed with Raney nickel or nickel oxide were tested. Those catalysts had very low resistance to gas flow; 90 percent lower than nickel granules used in previous experiments. In a single stage of synthesis thee nickel plates were only partially successful. Although the heating values of the product gas ranged from 856 to 941 Btu per cubic foot, the carbon monoxide content of he gas was above 0.1 percent. Both steel and wrought turnings were tested in single-stage synthesis, but the conversion of hydrogen and carbon monoxide was too low to attain the desired heating value of 900 Btu per cubic foot in the product gas. Assemblies of plates thermally sprayed with fusel iron were tried in an experiment to make gasoline. A gasoline yield of 52 percent (of the hydro¬carbons produced) was obtained using a 1H2-10O feed These sprayed assemblies were in service for 1,500 hours, the longest that this type of catalyst has been used. When a second reactor containing Raney nickel catalyst was added in series with the first reactor, complete utilization of the feed gas was obtained because in addition to the liquid product, a high-Btu gas with a heating value of 800 Btu per cubic foot was made.

Jan 1, 1965

By Roswell W. Prouty

As part of a general plan for control and economic utilization of the waters of the Missouri River Basin as well as development of its inherent power resources, the Corps of Engineers of the United States Army has under construction a rolled earth dam near the site of old Fort Randall in South Dakota. The dam is in Charles Mix and Gregory Counties on the Missouri River at a point about 922 miles above its mouth. It is approximately 125 air-line miles southeast of Pierre and 55 miles southwest of Mitchell, S. Dak. The storage reservoir to be formed by the dam will extend upstream for 150 miles and, at maximum operating pool level, will cover an area of some 107,000 acres. It will have a storage capacity of 6.2 million acre feat.

Jun 1, 1949

By Verne E. Hooker

The Bureau of Mines conducted a preliminary investigation to determine the state of stress in crystalline rock outcrops near Atlanta, Ga. The secondary principal stresses in a horizontal plane near the surface are compressive and are 500 to 3,000 psi. The maximum compressive stress is northeast-southwest in the Stone Mountain-Lithonia district but changes to northwest-southeast near Douglasville. The elastic constants were determined from data obtained by static and dynamic laboratory methods and in situ velocity measurements. Results show Young's modulus to be dependent upon both stress level and anisotropy in the rock. Average secant moduli obtained from triaxial tests were used to compute the applied stress from borehole deformation measurements.

Jan 1, 1966

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 17 and 23, outlining the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of publications recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 17 and condition 2 on page 23. An explosive or y blasting device enumerated in the permissible Lists of thin Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1941

By Edward L. McHugh

Twelve properties in the Riverside Mountains have moderate to high potential, for silver, gold, copper, and molybdenum. Six properties in the Big Maria Mountains have moderate potential for zinc, lead, copper, silver, iron ore, and limestone. The Big Maria Mountains also have occurrences of building stone. Four properties in or near the study area have low-grade gold-silver-copper resources totalling more than 300 thousand tons (270,000 t). An estimated 29 million tons (26 million t) of limestone and dolomite, and 620,000 long tons (630,000 t) of iron ore are in the Big Maria Mountains section of the study area. INTRODUCTION The Big Maria Mountains Wilderness Study Area covers about 50,538 acres (20,453 ha) near the Colorado River in eastern Riverside County, California (fig. 1). The study includes portions of both the Big Maria and Riverside Mountains. It lies north of Blythe, California and south of California Highway 62 in the Mojave Desert province of the California Desert Conservation Area. The study area consists of two mountain ranges surrounded mostly by broad alluvial slopes or bajadas. It extends for 25 mi (40 km) from the Riverside Mountains on the north, to the south end of the elongate Big Maria Mountains.

Jan 1, 1982

By F. W. Lee

List of GEOPHYSICAL ABSTRACTS

Jul 1, 1932

By Raymond O. Dannenberg

The Bureau of Mines conducted laboratory and full-scale tests to develop a process for improving the flotation characteristics of lime-treated waste water produced by the Kennecott Copper Corp., Magna, UT. Unknown substances in the waste water reduced the flotation efficiency of the metal sulfides. An estimated annual loss of 795,000 lb Cu, 232,000 lb Mo, 5,625 tr oz Ag, and 617 tr oz Au would result from recycling the total flow from the lime treatment plant to the flotation mill in an effort to conserve water and reduce associated expense. The tests indicated that aeration or treatment with activated carbon significantly improved the water quality. The improvements in molybdenum recovery averaged 8 pct for carbon, 11 pet for activated carbon, and 16 pct for combined aeration and activated carbon. The combination of the two processes produced water quality as good as or better than normal feed water.

Jan 1, 2011

By D. R. Mathews

The solubility of carbon in electrorefined vanadium was determined to be approximately 0.27 wt pct at the eutectic temperature 1,650° C and 0.03 wt pct at 700° C. The tensile strength and hardness of vanadium increased with car-bon content to the solubility limit, but this effect was small, probably because of the narrow solubility range. Between the solubility limit and 0.3 weight-percent carbon, the second phase had essentially no strengthening effect in vanadium. The second phase, observed metallographically at the grain boundaries and within the grains, was shown by autoradiography to contain high-carbon concentrations. This second phase was identified as VgC by X-ray analysis. The VgC in the grain boundaries contributed largely to the poor cold-and-hot workability of vanadium-carbon alloys. Increased concentrations of V2C occurred at the grain boundaries of the high-carbon alloy ingots as a result of homogenization at 1,600° C for 1 hour. Alloy ingots containing more than 0.36 wt pet carbon (a calculated 2.9 wt pct VaC) following homogenization, cracked severely and failed by intergranular fracture upon swaging at 900° C.

Jan 1, 1965

By Alexander May

The U.S. Bureau of Mines conducted studies to determine if phosphate slag stockpiles at Tennessee Valley Authority's National Fertilizer Development Center were hazardous materials. The stockpiles were not hazardous materials as determined by Environmental Protection Agency (EPA) extraction procedure (EP) toxicity test. Radium-226 concentration was 28.7 pCi/g in slag and 2.1 pCi/g in background material. Radium-226 was not leached from the slag. Fluoride concentration was 3.87 pct in slag, 0.18 pct in subsurface material under slag, and 0.08 pct in the background. Slag material permeability was 1.65 x 10-3 cm/s, and subsurface material permeability was 3.24 x 10-6 cm/s. Rain water, trapped in a depression on top of the east slag stockpile, became seepage water at the base of the stockpile. Concentrations of EPA toxic elements in seepage water were much less than concentrations from an EPA EP toxicity test on the slag. Twelve elements-Na, Mg, Ca, Sr, Ba, Cr, Mn, Co, Cu, Cd, AI, and P-had higher concentrations in seepage water than in rain water on top of the slag stockpiles, or in creek water adjacent to stockpile bases, indicating that they were leached from slag stockpiles.

Jan 1, 1990

By Jr. Holmes

The Bureau of Mines drilled and sampled the more important magnesite deposits in the Currant Creek Mining District, White Pine County, Nev. The properties of the Ala-Mar Magnesium Co., Inc., and the Nevada Magnesite Co. were examined in August 1942 by D. W. Butner, engineer of the Bureau of Mines, to determine the advisability of investigating the deposits under the strategic minerals program. Development involving diamond drilling, trenching, and sampling was started September 1, 1942, and was completed in the latter part of November 1942. The deposits are on unsurveyed public land in T. 12N., B. 59 E., M.D.B.&M., in an area of high relief ranging from 7,300 to 8,100 feet in altitude. Both properties are situated northwest of the Tonopah-Ely Highway, U.S. Highway 6, from which a dirt road extends about 4.6 miles northwesterly, about 35 miles southwest of Ely, to the Ala-Mar property, and another dirt road extends about 10 miles westerly, about 26 miles southwest of Ely, to the Nevada Magnesite property. The magnesite occurs as irregular nodules, veins, and lenses in a bedded calcareous tuff formation, which overlies a group of volcanic rocks, and which is capped by remnants of rhyolite flows.

Jan 1, 1950

By W. P. Huleatt, R. B. McCulloch

"The Big Four zinc-deposit, directly above the north bank of the Green Mountain Reservoir on the Blue River, Summit County, Cole., was discovered in 1937 by the present owner, Walter McDaniel, who lives on the property. Mr. McDaniel, together with members of his family, have worked the mine on a small scale since its beginning and have shipped quantities of sorted high-grade ore to the International Smelting Co. at Tooele, Utah, and the Combined Metals Corp. at Bauer, Utah. More recently, parts of the nine have been operated by lessees.The property had been examined previously by the Federal Geological Survey, and the geological report was made available' to the Bureau of Mines.The Big Four mining claim was located in 1937 by Walter McDaniel and his wife Frances,- who had been prospecting in the vicinity since 1933. The discovery of the high-grade zinc deposit caused considerable excitement, as it had not been regarded as a mineralized area.Mining was begun in 1937 and carried on until 1944 by Mr. and Mrs. McDaniel with the help of a few hired miners. During 1944, parts of the mine were leased: to various parties Who produced small quantities of ore but did no development work.Shipments during 1941 .totaled 752 tons; during 1942, 387 tons; and during 1943, 510 tons. From the beginning of 1944 to April of that year, 98 tons wore produced and shipped to Utah,Since the lessees began operations, a grade of 30 to 35 percent zinc has been maintained by careful sorting. No production has been recorded for 1945.The Big Four mine is situated on Colorado State- Highway 9 between Dillon and Kremmling on the south face of Green Mountain overlooking the Green Mountain Reservoir, a Federal irrigation project on the Hue River, Green Mountain rises 1,600 feet above the general level of the valley to an altitude of 9,408 feet and the surrounding terrain, i s correspondingly mountainous and rugged."

Apr 1, 1946