Search Documents

Antitrust Investigation Dropped. - The Department of Justice announced that it was dropping its 5-year investigation of the aluminum industry. The investigation was over whether the aluminum companies were acting as if they were a shared monopoly. Deep Seabed Mining. - The Department of Commerce's National Oceanic and Atmospheric Administration (NOAA) has established an Office of Ocean Minerals and Energy which will be responsible for implementing the Deep Seabed Nard Minerals and Energy Act and the Ocean Thermal Energy Conversion Act. It will establish licensing and regulatory programs.

Jan 1, 1980

By A. L. Engel

This report is a compilation of results of preliminary tests on scheelite (tungsten) ores and tailings. These investigations were made to assist in establishing satisfactory treatment methods for small-scale concentrator operations, or to indicate a. method for conserving previously lost mineral values in old tailings, if possible. A discussion of test procedures is included, as it was felt that this would add to understanding the results reported under the several projects. The treatment of scheelite ores has become more or less standardized. Important differences occur in textures of ores from various mining districts. However, and this must be considered when planning ore-dressing operations. In most of the present investigations, only a limited amount of work was done, usually just enough to answer a specific question in regard to a particular ore or concerning local conditions. Two methods of treatment included gravity concentration, magnetic separation, and flotation.

Jan 1, 1952

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft Sinking operations could be reduced by over 30%, on the average with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By R. E. Gray

[The purpose of the study is to investigate cases of subsidence over abandoned mined-out areas of the Pittsburgh Coal identified from published and unpublished sources and to determine through a consideration of the geology, topography, climate, mining activity, and evidence at ground surface, what mechanisms control subsidence .and under what circumstances it takes place. The study wan performed it two phases, the first to identify all documented incidents of subsidence in mined-out areas of the Pittsburgh coal Region; and the second, to study a particular portion of the region in detail, collecting pertinent data relative to the sites within, characterizing roil the nature of the subsidence and its economic consequences, and determining the applicability of the findings to other areas whore similar problems with the collapse of abandoned miner have been encountered.]

Jan 1, 1977

By B. C. Christensen

The contract objectives are (1) to develop safe practice guidelines which will minimize the chance of fires in underground fueling areas and (2) to develop a low-cost, reliable, automatic fire protection system for underground fueling areas. The effort described by this report covers the period from 21 June 1976 to 30 September 1977 and accomplished the following tasks: ? Preparation of Data Plan and Data Acquisition, mainly through visits to sixteen mine sites and a literature survey. ? Analysis of the accumulated data, providing design inputs for (a) evaluation of the fire problem; (b) development of safe practice guidelines; and (c) development of recommended design concepts for automatic fire protection systems. ? Preparation of safe practice guidelines for underground fueling areas. ? Preparation of recommended design concepts for automatic fire protection systems for underground fueling areas. ? Design and fabrication of fire protection system for installation at Pine Creek Mine, Bishop, California. ? Install system and perform underground fire tests at Pine Creek Mine.

Jan 1, 1977

By J. O. Merritt

The primary objective of this research program was to recommend ranges of minimum luminance for safety in underground metal and nonmetal mining. Visual tasks critical to safety were identified and rank-ordered. Realistic, full-scale, dynamic task simulations encompassing the most important visual components of the critical tasks were installed in a large simulated workspace. Five trained observers performed the six simulated mining tasks under varying levels of luminance. Over 13,000 measurements of visual task performance were used in developing minimum luminance recommendations for the on-foot underground worker and the mobile equipment operator.

Jan 1, 1983

By F. A. Rutledge, J. J. Mulligan, W. H. Kems, R. L. Thome

"As a part of the United States Department of the Interior program for the development and use of Alaska raw materials, the Bureau of Mines is conducting an investigation of deposits f nonmetallic minerals accessible to the Alaska Railroad for use in building materials in the Alaska Railroad-belt area. The results of the investigations, to date, indicate that raw materials for the production of brick products are in plentiful supply as clay in the Anchorage area, as fire clay at Sheep Mountain, and as shale in the Healy Creek coal formations near Healy, Alaska.Shale for the production of lightweight aggregate or Haydite occurs near mile 67 on the Glenn Highway, and preliminary tests give excellent results. Physical tests are new in progress on commercial-size concrete building units made with this aggregate. Another shale deposit in the same formation was located at mile 16 on the Matanuska Branch of the Alaska Railroad, and preliminary tests give comparable results.Natural lightweight aggregate in tree form of pumice and pumicite occurs in Katmai National Monument and has been used with excellent results in lightweight-building units in Anchorage and Fairbanks. These deposits will be investigated in more detail by the Bureau of Mines during 1952.One small perlite deposit near Healy, Alaska, showed excellent expanding properties, and the product compares favorably with commercial perlites being used in the States for plaster and concrete aggregates. Additional investigation by the Bureau of Mines to delimit the known occurrence and, if possible, discover others were planned for the 1951 field season.The pumice from Katmai National Monument also was considered for use as a pozzolan in pozzolan-portland concrete. Tests by the Bureau of Reclamation indicate that the pumice sample submitted by the Bureau of Mines would be satisfactory in strength development but is not outstanding. Natural activity is good and is greatly improved by calcination at 1,4000 F. Water requirements and shrinkage also are satisfactory. However, the material is ineffective in reducing expansion owing to alkali-aggregate reaction; and, if reactive aggregate is used to make concrete, it would not insure against excessive expansion. An attempt will, be made during the 1952 field season to delimit pumicite deposits along the Alaska Peninsula more amenable for use in pozzolan-portIand concrete.Because the Railroad belt has such a rigorous climate, insulation for new construction is of prime importance. Luring the Bureau of Mines, investigation of building materials all samples were submitted for chemical analyses as possible sources of raw materials for the production of rock wool, one of the best insulation mediums. Four areas having deposits of the required constitu¬ents were located as follows: Anchorage area, with Potter limestone and argillite; Cantwell-Windy area, with limestone and shale; West Fork of the Chulitna River area, with limestone and agrillite; and Homer-Seldoyla area, with Seldovia limestone and Homer clay. It was planned to take bulk samples of these formations and submit them for testing during the 1951 field season."

Mar 1, 1953

By Michael Rieber

The increase in f.o.b. mine prices of coal from $5/ton to over $18/ton in five years [1] has increased the significance of transportation costs. Coals produced in the vicinity of the consumer bear a much lower transport cost than those produced in the west. This differential may be used for flue gas desulfurization, other cleaning, or further processing of local coals. To the extent that western coals are cheaper to produce and have a lower sulfur content, they offset the locational disadvantage. To the extent that they have a lower heating value, the disadvantage is exercabated. Given the other conditions, an accurate analysis of transport costs will help suggest the location of coal mining and the moue of transport both transport costs and tariffs have risen. Together they have increased delivered coal prices, altered the balance between the use of coal and other fuels, helped to alter the location of mining activity, and put pressure on consumers to examine the cost effectiveness of alternative transport modes. Transportation options for long distance coal movements include rail, barge, pipeline, and EHV transmission lines. A summary of system parameters is shown in Table 2.1. Barge transport, pneumatic and slurry pipelines are discussed elsewhere in this report. Together with EHV, they have been the subject of previous studies [2,3,4]. Slurry pipelines have been shown to be especially useful where rails are not available [2] but the technical problems of dewatering, handling, and utilization of lines [5] remain unresolved. They are discussed in Section 3. Barge transportation depends on the location of the mine and consumer with respect to the waterway system. One drawback of barge shipment is interruptions due to winter, and low or high water conditions. Mine mouth power generation followed by EHV transmission of over 500 miles has been shown to be the most expensive means of delivering an equivalent amount of energy to consumers [2].

Jan 1, 1977

By W. B. Berwald

[Accurate ~cusirc::ie t of euusu.rface r,resw rus £Uld tee:: ?er:~t:,res in producin+ oil and as wells is one of tine ast iy,ulortant steps ever t,.s:en to place the rprwctice of retroleum ,-iroduction on an exact scientific basis. i'reerures and teial.or-tures in a -petrolcuia r4:, rvoir. have a rn..r..ed influence over the o:wvement of oil and ~c s both within the. reservoir and t~:rou,=Ii the various-size "flow otrin;;u" of proLucin,; wells to tine surface. Knovrled: ?c of theso fc,.ctgrs form a Laois for cny attei:ant to [.,-~ly eciantific j:cthods to the solution or analysio of mc.nj proble;ae encountered in the production of oil and 1c_c, Without a.ccur:tc mcaaurx,ients of reosures r:.nd tcn::paratuxes within the rocervoit and -well 'flo-,r strinL:s" tae aI,licution of w.ny proved enbinecrin and scientific princiy-,loo is on %,]

Jan 1, 1935

By Keith L. Harris

Recent data indicate a marginal decline in overall growth in world economic output from 3.1% in 1985 to 2.9% in 1986 (table 1),2, 3 Many nations experienced slower economic growth because of the huge trade imbalances existing between the United [ ] States and Japan and the Federal Republic of Germany, the U.S. budget deficit, and the growing Third World debt. Some developing nations, however, experienced booming growth. Declining prices for energy and nonenergy commodities and the fall of the dollar against the currencies of major industrial countries benefited several developing countries--energy importers and exporters of manufactured goods with currencies tied to the U.S. dollar, which were able to expand markets in the industrialized nations. The drop in commodity prices increased demand in industrial countries and depressed it in developing countries. Lower demand in the developing countries contributed to a decline in the real net exports from industrial countries. As a result, output growth in industrial countries declined from 3.0% in 1985 to 2.4% in 1986, despite growing internal demand, Average output growth of developing countries increased from 3.296 to 3.596 during the same period, however, primarily because of the low prices of their products and the strength of demand in industrial countries for those products. Developed country output growth was extremely uneven, however. For example, the economic output of nonfuel exporters grew 5.4% in 1986, while that of fuel exporters dropped 0.7%.

Jan 1, 1987

By R. Farrar

Protective canopies for conventional electric face equipment, including shuttle cars, operating in low coal (less than 48 inches) were designed, fabricated, installed and evaluated on in-mine machines engaged in regular coal mining operations. This work was performed under contract to the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center. The canopies will support a vertical load of 18,000 pounds and provide protection against both roof falls and contact with the mine rib. Canopy configurations were established based on human engineering studies, full scale canopy mockups, and in-mine observation and consultation with mine and equipment manufacturing personnel. Overall height of each canopy is hydraulically adjustable between a minimum of 32 inches and a maximum of 40 inches. Canopy tops are open framework, welded structures, covered with expanded metal mesh. Structural members are 1 3/4-inch or 2-inch square tubing of AISI 413ON and ASTM A500 material, respectively. The canopy tops are typically supported by an understructure and upright post arrangement that is either integrated into the current operator platform or attached to the machine frame. The four upright corner posts house the hydraulic actuators. Canopy tops are elevated horizontally. Canopies are welded or bolted to the existing machines. Installation is accomplished with a minimal amount of interface modifications. No major machine design changes are required. Canopies were trial installed and load tested at the manufacturer's facility prior to installation on the in-mine machines. Canopies were installed on a Joy 14BU10 Loader, 16RB-3AH Cutter, and two 21SC Shuttle Cars, and a Galis 300 Roof Drill and 460-S Face Drill. Canopy installations were evaluated in the Jewell Ridge Coal Company No. 12 and Big Creek Tiller Mines. Operational time accumulated on the installations during evaluation ranged from 1 week to 14 weeks of two-shift operation. All five canopy designs, manufacture, and test were successfully accomplished. The five canopies met all safety requirements. Three of the five canopies were deemed to be completely successful from an operator's point of view. That is, mine management as well as the machine operator found that the canopies did not impede the operation of the machines to function with the same efficiency as before the installation of the canopies. The loader canopy, in fact, appeared to have provided a mole efficient operation of the loader by providing added safety to the operator from rib contact thus allowing him to concentrate more fully on the loading function. Operational problems were encountered with the shuttle car and the roof drill. The shuttle car canopy obstructed visibility to an objectionable amount and the roof drill canopy impeded maneuverability of the machine, more than doubling the roof bolting time.

Jan 1, 2012

By William D. Dodge

A typical quality program plan is presented for explosion-proof (XP) electrical enclosures. The plan is suggested for manufactures of XP enclosures which are to be certified by MSHA for mining use. The plan describes the quality system, organization and implementing mechanisms which are to be applied in the manufacture and delivery of certified XP enclosures. Example forms and example procedures are included.

Jan 1, 1984

By T. F. Myners

This paper, describing the concentration methods and costs of Witherbee, Sherman and Company at Mineville, N. Y., is one of the series of papers on milling methods and costs being prepared by the United States Bureau of Mines. It deals principally with the production of high-grade concentrate. ACKNOWLEDGMENT The author is indebted to C. F. Jackson, principal mining engineer, United States Bureau of Mines, to A. M. Cummings, general superintendent of Witherbee, Sherman and Company, and to the company's engineering staff, for assistance in preparing this paper.

Jan 1, 1932

By Donald F. Reed

Deposits of gray hematite occur in two districts in Talladega County, Ala., the Emauhee-Tallasechatch and Weewoka, both in the; vicinity of Wintorboro, 50 miles east of Birmingham. The deposits were investigated by the Bureau of Mines in 1945 and 1944. Approximately 15,000 feet of diamond drilling was done and 6,000 linear feet of trenches excavated and sampled.

Jan 1, 1949

By W. J. Kroll

This investigation was undertaken with the idea of studying a number of unconventional methods for making chromium to determine whether production cost could be lowered and to discuss some of the more recently described processes. These comprise carbon reduction of the oxide in vacuum, nitride dissociation, fusion electrolysis of the chloride, amalgam method, iodide dissociation, calcium reduction of the oxide, hydrogen reduction of the chloride, and reduction of this compound with zinc and with magnesium. Preference is given this latter method, which is shown in a flow sheet. Special attention is given purification of the chloride and separation of the vacuum at about 900° C. A reduction method for the elimination of traces of oxide contained in pure chromium by pure hydrogen obtained from the dissociation of zirconium hydride is described. The various methods are compared in a table in the appendix. Aluminothermic and silicothermic methods for the reduction of chromium oxide and the aqueous electrolysis have been disregarded in this investigation.

Jan 1, 1950

By Donald Koch

The project investigated regional impacts of mining on the ground water system of the Powder River Basin by: 1) establishment of a regional ground water monitoring network, and 2)development of , set of digital computer models to simulate ground water flow and quality, ground water contributions to surface water flow and quality (i.e., baseflow), and watershed run-off and recharge. Over 100 wells were monitored for physical and chemical parameters. Data were used as input to the model; and for the development of a comprehensive data base. The basin was modeled on a regional and subregional scale using a finite -difference model employing an alternating difference technique. Two water-shed models were evaluated for their ability to provide runoff and recharge inputs to the basic ground water model. Application of the regional and subregional models using conservative mining scenarios showed that drawdowns may extend west from the mines as far as ten miles but that impacts would be insignificant on a regional scale. The watershed model could be effectively applied to small watersheds only.

Jan 1, 1982

By George S. Rice

The major purpose of this bulletin, as indicated in the preface by Dr. John W. Finch, Director of the Bureau of Mines, is to give a critical review of the coal-mining methods used in the principal producing countries of Europe, to describe the reasons underlying the adoption of these methods, and to contrast them with coal-mining methods employed in the United States. The report includes discussions of various subjects intimately related to coal mining, such as geology of the principal coal fields; production and resources of the several countries; mine safety and health research; Government mining regulations; mine inspection and rescue procedure; safety lamps; fixed lighting methods under-ground; testing electric motors, mining machines, and mining explosives for permissibility; and special mining hazards, such as explosions of gas and coal dust, mine fires, instantaneous gas outbursts, ground movement and surface subsidence, and bumps. Commercial, economic, and labor problems of European coal mining, including miners' output, wages, and social-insurance schemes, as well as cost of mining, prices of coal, etc., are briefly described. It will be noted that data on most subjects are not given for Russia, which has become an important coal-producing country, owing to the lack of reliable published information concerning Russian coal mining.

Jan 1, 1939

The Bureau of Mines has reviewed those portions of the "Tariff Schedules of the United States Annotated 1963" that are of interest to the minerals industry. This study shows to what extent rates of duty were altered (increased or decreased), and provides a bridge where possible from the old Schedule A classification sys tem to the new TSUS system of statistical reporting of import data. In general the new tariff has corrected previous classification defects and inconsistencies, but the rates of duties have not been materially changed.

Jan 1, 1965

By Charles B. Carpenter

The New Hope field was selected for study by; Bureau of lanes engineers because many problems met by, the operators during development and operation were unique to petroleum-engineering experience. Solving these problems is believed to have doubled the ultimate recovery of oil from the field. Since the discovery well was 'completed, in April 1943, an oil-productive area of 4,950 acres- has been delineated by the drilling of 64 wells, four of which were dry holes. Four oil-bearing reservoirs - the Bacon oolitic limestone, and the Hill, Pittsburg) and Elledge sandstones, all, in the Trinity group of the Lower Cretaceous series-- have been penetrated at depths ranging from 7,300 to 8,100 feet. Three of these reservoirs were found to be closed-type or solution gas-drive reservoirs, and one - the Hill - was an open-type or water-drive reservoir. During the course of the study, the Tide Water Associated, Oil Co. and -Seaboard al Co. of Delaware made available to the writers all well records, electric logs; and coring, production,, and pressure data. The ,writers performed Certain field and laboratory- tests on cores of ,the reservoir racks and' samples -of the reservoir Oils. Analyses of cores from the four reservoirs showed average .porosities ranging from 10 to 18 percent, average permeabilities of 17 to 297 millidarcys, and -average 'connate water contents ranging from 25.4 to 30.6 percent. Subsurface and recombined samples of reservoir oils indicated that the oils in the Bacon Hill, and Pittsburg reservoirs contained ,206 to 422 cubic feet of gas in solution per barrel initially, and that the, reservoir oils were undersaturated with gas. No samples' of oil from the Elledge reservoir were analyzed, and because of meager data this reservoir was not studied in detail. 4 The presence of free 'gas' or a' gas cap, however, indicated that the oil in the Elledge reservoir was saturated with gas. The rapid decline in pressures in- the' four reservoirs during the 'first year of operation alarmed the operators and provoked them to investigate the reservoir conditions to determine the cause.

Jan 1, 1949

By J. D. Bardill

"The Stoddard mine, Cheshire County, N. H., was explored by the Bureau of Mines in 1944 as a source of the strategic fluorite. It was reported that the vein persisted in the bottom of old workings and the geology of the immediate area indicated the possibility of finding additional lenses.In its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts pre¬liminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is expressed for the cooperation and assistance given by Robert F. Sherwood of the United Feldspar & Minerals Corp.; by McHenry Mosier, chief, College Park Division, Mining Branch, who aided in re¬vising this report; and by J. B. Zadra, chief, College Park Division, Metallurgical Branch, and others of his staff, who assisted in performing the beneficiation tests and analyzing samples. The field work was under the direction of Harry P. Hermance.The property lies on the southern boundary of the town of Westmoreland, Cheshire County, N. H., at approximately 72° 39’ west longitude, 42° 27’ north latitude, in the Keene, N. H. (G.S.) quadrangle.Good gravel roads lead from paved State Highway 63 to the property. A dirt road in fair condition suitable for truck leads to the nine.Dwight H. Smith, Putney, Vt., is the owner and has leased the property to the United Feldspar & Minerals Corp., 10 East 40th Street, New York 16, N. Y.Property titles were not investigated.The fluorite deposits of Cheshire Count', H. H., have been known for many years, being reported by Jackson, (Geology and Mineralogy of New Hampshire, by Charles T, Jackson, 1844) and by Hitchcock, in1878 (Geology of Now Hampshire, vol. 3, 1878, by Charles H. Hitchcock). A large pit on the largest or east vein was mined by Lovat Frazer from about 1908 to 1917, This operation is reported to have produced approximately 3,500 tons of fluorspar. In 1917, the American Steel & Wire Co, took over the mine end is said to have produced 3,500 tons of fluorspar before relinquishing the lease in 1923.From 1935 to 1937 the New Hampshire Fluorspar Cc. operated the Stoddard mine, working chiefly on the most westerly of the three known veins on the property, as well as doing some preliminary work on the small central vein. In 1938, the United Feldspar 6 Minerals Corp. leased the mine, and less than 100 tons of fluorspar was produced from exploration and development work, No mining has been done since that time."

Sep 1, 1946