Search Documents

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

By Robert J. Pokora

This report summarizes the work performed under USBM Contract No. J0100038, "Demonstration of Noise Control Techniques for the Crushing and Screening of Nonmetallic Minerals." The objectives of the program were to: a. Identify the prevalent sources of crushing and screening noise in portable and stationary plants b. Design retrofit noise control treatments for those sources c. Field test control treatments under actual operating conditions. A census of the nonmetallic industry was performed to determine the number and types of crushing and screening equipment. Based on the census, eight plants were selected and surveyed to assess the variety of noise sources, determine the worker noise exposure to those sources, and to identify possible constraints that had to be considered in designing and installing the retrofit controls. Three plants were selected from those surveyed and retrofit noise control treatments were designed, including: a. A primary crusher operator control booth b. Screen decks made of resilient cloth c. Screen feedbox impact pads d. Rubber feed plate for secondary crusher e. Rubber feed chute linings for secondary crusher f. Noise attenuating curtain for secondary crusher. A new primary crusher control booth was installed at one plant, and the operator noise levels were reduced from 97 dBA to 78 dBA. Screen noise at the two secondary crushing plants was reduced by 3 dBA to 7 dBA; crusher noise was reduced by 5 dBA at one of these two plants. Noise levels at normal outside operator and cleanup locations were reduced by 4 dBA to 7 dBA at one secondary plant, but operator/cleanup noise levels were not significantly reduced in the second plant due to rapid wear of installed materials. At one of the two secondary plants the retrofit noise control materials displayed excellent wear characteristics. The rapid wear of retrofit materials at the second plant was due to improper materials being supplied and changing circuit conditions.

Jan 1, 1982

By A. Galaitsis

This report summarizes part of the work performed under the USBM Contract No. H0155113, "Noise Abatement of Continuous Mining Machines." It reviews, briefly, the aboveground tests performed on a Jeffrey 120M conveyor that were documented in Vol. I of the subject contract; and describes the performance of treatments implemented on underground equipment. The noise level at the operator's position in the aboveground-test facility was reduced from 101.5 to 91 dBA using treatments with satisfactory - aboveground - durability. Extensive underground evaluation has been performed only on the constrained layer damping, which has reduced the conveyor noise by 2 to 6 dBA depending on the operating conditions, and has been shown to be sufficiently durable. Other promising candidates for exploratory evaluation include resilient layers for the top/bottom decks, and smoother discontinuities between adjacent conveyor sections.

Jan 1, 1983

By Frederick C. Kohout

An advanced water-in-oil emulsion hydraulic fluid has been developed which meets defined laboratory performance criteria and which has given fully satisfactory results in a one-year underground mine test in two continuous miners. A novel method of monitoring fluid water content was demonstrated and incorporated into a test kit for use at or near the mine site. Test fluid fire resistance integrity as measured by the MSHA Schedule 30 procedure was maintained during the test and important fire resistance test variables identified.

Jan 1, 1979

By Kevin Hennings

Screening efficiency models developed to date rely almost exclusively on empirical formulas based upon large amounts of acquired operating data. A screening model was developed using a combination of empirical coefficients and explicit mathematical expressions which quantify screening phenomena. A series of screening tests was run to supply data for purposes of correlation and empirical coefficient evaluation. The model has been implemented as a digital computer program. The validity of the modeling procedure has been established by laboratory testing. Results generated by the model have been used to compile an applications handbook, which can be used to predict screening performance in lieu of using the computer program.

Jan 1, 1982

By Louis Schaffer

This report characterizes several coal Dine mobile equipment operator populations with respect to age, mine experience, machine operator experience, and training. The information is used to demonstrate a method of normalizing the injury data collected by the Mining Enforcement and Safety Administration-Health and Safety Analysis Center.

Jan 1, 1977

This report summarizes the work performed under USBM Contract No. H0395041. The primary objective of this work was to extend the noise control technology developed under earlier USBM projects to a wider range of load-haul-dump models to evaluate the general applicability of these techniques. Noise control treatments were designed, fabricated, and installed on three Wagner LHDs (an 5T-2B, ST-2D, and an 5T-8A) selected as demonstration machines for this project. The machines were evaluated either in production mines or at the Bureau's Lake Lynn Mine. The results indicate that it is possible to achieve overall noise reductions of between 4 and 8 dB using these techniques. Engine cooling and seal design were determined to be important design issues in such treatments.

Jan 1, 1984

By Robert W. Geehan

A preliminary examination of the Dayton iron deposit was made in 1941 and 1942 by Paul E. Pesonen and O. H. Metzger, engineers of the Bureau of Nines. Trenching and sampling were recommended, to be followed by core drilling if favorable results were obtained. The Bureau of Mines conducted a project at the property from June to December 1942. The deposit is in sec. 6, T. 17 N., R. 23 E.; sec. 31, T. 18 N., R. 23 E.; sec. 36, T. 18 N., R. 22 E.; and sec. 1, T. 17 N., R. 22 E., M. D. B. & M., about 15 miles west of Lahontan Reservoir in Lyon and Storey Counties, Nev. It lies at an altitude of about 4,500 feet north of the Carson Plains, in the foothill section of mountains that rise to about 7,000 feet to the north of the property. The deposit may be reached by driving 12.5 miles northeast of Dayton over U. S. Highway 50, thence northerly 2.7 miles over a dirt road to the property. The climate is hot and dry in summer, with occasional thunderstorms some of cloudburst variety, and frequent high winds. Winters are usually moderate, with light snowfall and some subfreezing temperature.

Jan 1, 1949

By John D. Spencer

Projects aimed at achieving the least disturbance to the Nation's air, water, and land resources in the mining and utilization of coal continued to be a feature of the Bureau of Mines coal program. This reflects the current concern about damage inflicted on the environment by our growing and increasingly affluent society. Mine Health and Safety research, along with investigations related to all other aspects of coal extraction and use, also continued to be implemented and expanded.

Jan 1, 1970

By T. J. Batchler, T. M. Barczak

The Code of Federal Regulations (CFR) requires that the transverse load capacity of stoppings be equal to or greater than traditionally accepted in mine controls, which for block stoppings is generally accepted as 39 psf as referenced in the preamble to the CFR standard. This measure is based on physical testing of a freestanding wall in accordance with ASTM E 72 specifications, where our past research has shown that the dominant parameter is the tensile strength of the sealant. A new protocol based on rigid arch loading of the structure is proposed to determine the true transverse load capacity of block stoppings. Arching is achieved by the restraint of the stopping against the mine roof and floor, whereby compressive forces are developed within the wall. A laboratory procedure using the NIOSH Mine Roof Simulator (MRS) to simulate rigid arching of block stoppings was developed and results verified through full-scale in-mine tests. The rigid arch tests have demonstrated transverse load capacities more than an order of magnitude higher than the ASTM E 72 evaluation method from which the 39-psf requirement is derived. More importantly, the rigid arch tests have shown that the load capability is dependent on the physical properties of the block and geometric properties of the wall and not the sealant.

This report summarizes the results of several field tests conducted by Collins for the Bureau of Mines under contract S0122076 and contract H0232056. The field projects represent a part of Collins continuing effort on a broad study of coal mine communications. These experiments analyze the propagation characteristics of radio signals in a working coal mine environment. The intent of the program is to provide basic propagation loss characteristics by which we may evaluate various approaches to an integrated mine communications system. The goal of such a system is to satisfy both operational and emergency communications needs in the mine.

Jan 1, 1974

By William D. Monaghan, Michael A. Trevits

Over the period 2000 to 2003, roof falls have accounted for 4 to 14% of the fatalities in underground mining operations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the frequency, exposure, and risk of these events through an ongoing program of field and laboratory studies. One area of research involves the evaluation of polyurethane grouting technology that is commonly used to stabilize fractured mine roof strata. Concurrently, NIOSH is conducting work to evaluate the application of ground penetrating radar for advanced delineation of problematic mining areas. In this study, NIOSH partnered with Sub-Technical, Inc. who injected a polyurethane grout (also known as glue) into a roof area of NIOSH’s Safety Research Coal Mine. The mine roof area was scanned using ground penetrating radar technology before and after grout injection in an attempt to determine the extent of grout infiltration. A comparison of the pre-and post-grouting radar records showed a significant change at a mine roof depth of about four to five feet. The interpreted radar records were then compared with drill core information, borescope evaluation of roof-bolt holes in the study area, and underground observations. At this site, the interpretations of the radar records correlated with data obtained from the core holes, borescope evaluations and underground observations. This study showed that ground penetrating radar technology can be a useful tool for detecting changes in mine roof due to the injection of the grout.

By Jerome Apt

This manual has been prepared fur the help and guidance of underground coal mine operators. It details both common and unique engineering methods by which the respirable dust, which is generated in coal mines, can be controlled. This document was compiled by Apt, Bramer, Conrad and Associates, Inc. under contract number H0111464, issued by the U. S. Bureau of Mines and forms Volume II of the final report. This contract was authorized by and executed pursuant to the Federal Coal Mine Health and Safety. Act of 1969 (P. I. 91-173; 83 Stat. 742).

Jan 1, 1972

By Thomas J. Peters

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 7,000 acres of the 9,240-acre Little Blitzen Gorge Wilderness Study Area in Harney County, OR, to evaluate its mineral resources. The study area is dominated by a 1,500-ft-deep canyon that was carved by Pleistocene glaciers in gently westward-dipping homoclinal flows of Miocene Steens Basalt. The Bureau reviewed pertinent literature and county mining records During the field investigations, 18 rock samples were collected from basalt dikes, breccia, fractured or porphyritic flows, and 20 alluvial samples from gravel accumulations. Mercury anomalies from sampling by the Oregon Department of Geology and Mineral Industries could not be verified. The mercury might have originated -From the Pike Creek Formation, a known mercury-producing unit that may extend into the study area beneath the Steens Basalt. Any epithermal deposit at depth would be expensive to explore and develop.

Jan 1, 1986

By A. Gene Collins

Potassium, lithium, strontium, barium, and manganese are present in many oilfield brines, None of them except barium is determined routinely in brine analyses. Therefore, sensitive and accurate flame-spectrophotometric methods were developed. Potassium, lithium, and strontium were determined by a standard-addition technique in ethyl alcohol solutions. Barium and manganese were determined in ethyl alcohol and normal propyl solutions, respectively, after interfering substances were removed.

Jan 1, 1962

By Virgil A. Marple

The primary purpose of this contract was to evaluate methods and techniques by which the size distribution acid concentration of mining-related dusts can be measured. One result has been the development of a portable, battery-operated optical particle counter/ multi-channel analyzer system which can he used to determine the size distribution and concentration of mining aerosols. One important aspect of this program has been the development of a calibration technique which relates the output of the optical particle counter to the penetration of the particles through an impactor: This results in a calibration curve in terms of the aerodynamic or Stokes' diameter or the aerosol particles. Using this technique, calibrations were performed on coal, silica, Arizona road dust, potash, and rock dust (corer ore) aerosols. Another task of this program was the calibration and evaluation of the GCA respirible dust monitors (RMD) 101-1 and 301. The results of evaluation showed that the instruments were within the manufacturer's specification of ±25% of the true mass concentration up to about 15 mg/m , if the dust particles were in a size range from about 0.7 to 10 µm aerodynamic diameter. Particles smaller tan about 0.7 µm were not collected by the instrument and particles larger than about 10 µm were lose in the inlet. Other tasks included performing field studies in cooperative research programs with the Bureau of Mines personnel, development of a portable polystyrene latex generator for use in optical particle counter calibrations in the field. The incorporation of impactor classification devices on the inlets of aerosol mass measuring instruments to give mass size distributions, and a study of the density of coal particles as a function of the particle size.

Jan 1, 1977

By R. H. Nafziger

Bureau of Mines research has shown that very low-sulfur pressure vessel steels with improved mechanical properties can be prepared by two melting processes. Four pressure vessel steels having sulfur contents ranging from 0.0008 to 0.0040 wt-pct, were produced by the electric-arc furnace or by the electroslag processes. Calcium carbide was used as a desulfurizer in the electricarc furnace. Fluxes containing at least 40 wt-pct CaO provided sufficient desulfurization during electroslag remelting. Element recoveries were higher for electroslag remelting than for metal melted in the electric-arc furnace. Bar rolled from electroslag-remelted ingots generally possessed higher tensile strengths and ductility than bar rolled from it t melted in the electric-arc furnace. Charpy V-Notch upper shelf energies were also improved as a result of electroslag remelting. The primary failure mode during impact testing was was microvoid coalescence. Sulfide inclusions were minimal, especially in the electroslag-remelted material.

Jan 1, 1979

By Donald E. Buck

In 1988, Albania's centrally planned economy continued to decline. The country's officially published yearend economic report did not contain concrete results such as the growth of national income or industrial output. 2 The shortfall for central budget earnings for 1988 amounted to 9% below the planned target. Losses in industry were attributed to poor management and organization, as well as to low technical standards and excessive consumption of fuels and raw materials. The construction, energy, and mining sectors of industry did not meet their annual production plans. As in 1987, within these sectors, the chromite and petroleum extracting and processing industries continued to lag in output. Both chromite and petroleum remained Albania's chief sources of foreign exchange; the production downturn of these commodities continued to negatively affect the country's foreign trade position, especially in view of constitutional prohibitions against using foreign credit to finance trade. The chief events in the minerals industry in 1988 included the construction startup of the first of four planned new concentrators at the Bulquize chromite mine, as well as the construction startup of new ferrochromium capacities at Elbasan. Also, the copper mining industry reported the completion of facility expansion at the Perlat mine in the Mid-rite district. Albania began new facility construction at the Dinamo heavy-equipment enterprise at Tirana to maximize self-sufficiency in mining equipment production. Upon completion, the new factory would double the out-put of mining equipment at the enterprise and would introduce new designs for electric trucks and pneumatic drills for the mining industry. The new facility would also increase the production of new machinery and equipment for the country's beneficiation plants.

Jan 1, 1990

By D. R. Dolinar, A. T. Iannacchione

Limestone formations in the United States can be subject to relatively high horizontal stresses owing to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rock fall hazard. Rock falls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings has an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orienting the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and off-setting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.

By Donald J. Barnes

There are no producing or developing mines in the study area. The only mineral production was stone from a basalt deposit near Indian View Point. Cinders and sand and gravel have been produced from deposits within 1/2 mi (0.8 km) of the boundary. Stone, sand and gravel, and cinder deposits inside the area are not considered resources because equal or better quality material is found closer to markets. The study area has no known oil and gas, coal, geothermal, or other energy related deposits. However, in 1982 application was filed on 25,000 acres (10,125 ha) of petroleum and on 15,000 acres; (6,0/5 ha) of geothermal leases.

Jan 1, 1983