Search Documents

By William H. Holley

Thirteen additional preservative/fire retardant systems were applied to Ponderosa pine and evaluated for flammability both before and after water leaching. The more promising four systems were given a thorough evaluation for flame spread, toxic gas and smoke density levels, resistance to decay, and compressive strength. The most promising system on the basis of history of usage in the mine, ease of application and low cost as well as overall performance is the Fyreprufe/ACC Albi 107A/ 144 combination. A survey of inspection tools and instruments, identified equipment which could be assembled into an inspection kit for use in determining the extent of decay and/ or impregnant retention levels in mine timber. A literature search identified those high fire hazard areas found in a typical mine. Timber and other wooden structures used in such areas should be treated with an acceptable fire retardant system. A survey of insurance companies revealed that the use of such treated timber in the mines would probably have little or no impact on the rate structure.

Jan 1, 1980

By J. Koster

[Boron is an element whose metallurgical possibilities never have been investigated thoroughly, probably because of the difficulties experienced in the preparation of elemental boron and its intermetallic compounds. The southwestern United States contain the world's s largest deposits of boron minerals. In general, the mineral is readily available, and mining costs are not excessive. The most important boron mineral of commerce is borax (sodium tetraborate) however, there are large deposits of colemanite (a mineral having the composition represented by 2CaO 3B2O3 5H2O) in Clark County, Nov. This material was worked in times past by converting it to sodium tetraborate. In recent years the deposits have laid idle because of a mire readily available source of borax in the old lake beds of California.]

Jan 1, 1940

By T. T. Campbell

This investigation was undertaken by the Bureau of Mines to determine if high-purity ductile molybdenum of uniform quality can be prepared by bomb reduction techniques. Molybdenum trioxide (Mo03) and mixtures of molybdenum dioxide (Mo02) and trioxide were reduced by magnesium in closed steel bomb reactors. Very high pressures in excess of 5,000 p.s.i. developed during magnesium reductions of Mo03. The addition of calcium oxide to the bomb charges caused a significant reduction in pressure. Reaction efficiencies higher than 95 percent were obtained during magnesium reductions of either Mo03 or mixtures of Mo02 and Mo03, but high pressures were encountered when the charges contained from 30 to 60 percent Mo02. Reaction efficiencies were usually low (less than 80 percent) when the bomb charges contained more than 40 percent Mo02. The charges with the best composition considering operating pressure, yield, and purity contained from 10 to 30 percent Mo02. The addition of small amounts of carbon to the reaction charges was helpful because some deoxidation occurred during the reduction and also during subsequent arc-melting of the regulus metal. The purity of the bomb-reduced, arc-cast molybdenum metal ranged from 99.2 to 99.8 percent and in some instances the metal contained as little as 5 parts per million oxygen.

Jan 1, 1962

By A. W. Hall

A nuclear method was developed for continuously and automatically deter-mining the moisture content of coal flowing through a bin. Fast neutrons from a 1 curie americium-beryllium source penetrate the coal, are thermalized (slowed down) by hydrogen in the moisture, and are counted by a thermal neutron detector. The difference between the number of these thermal neutrons and those thermalized by dry coal (in a reference drum) is a measure of the moisture content of the coal. A materials handling system was developed and in tests at a commercial coal preparation plant, moisture in coal was monitored continuously within 0.2 percent of values determined by conventional means. The meter responded rapidly to change in moisture content, making it adaptable to automatic process control, and was operated for 1 year without malfunction or recalibration. Shielding of the source by the coal kept the neutron flux level at the bin wall less than 1 milliroentgen per hour, a safe level for personnel.

Jan 1, 1973

By Kenneth R. Maser

This report describes a research and development program sponsored by the United State s Bureau of Mines. The purpose of the program was to develop reusable explosion-proof bulkheads for a cross-cut emergency shelter, and to study the implementation of such bulk-heads, and the resulting shelters, as part of an emergency escape plan in a normal coal mining environment. The first part of this report reveals a number of significant conclusions regarding the application of emergency shelters. A study of the cause s of, and the conditions prevailing during a mine emergency indicate s that ideal placement of the shelter s would be midway along developing entries, and at the inter section of butt and main entries. The proper spacing of shelters is based on the travel capability of trapped miners, which is in turn dependent on the height of coal. The life of a given emergency shelter, based on an analysis of the above information, will be anywhere from 6 months to 10 years. Consequently, some shelters are regarded as "temporary?, while others "permanent?.

Jan 1, 1975

By J. Roth

The purpose of the present study is to increase the safety of explosive storage. This was accomplished by: a) review of the histories of recent and past magazine explosions to define causes and trends; b) observation of present-day explosive storage conditions and practices at active mines; c) examination of existing Federal regulations on explosive storage to determine whether they address all conceivable safety problems, whether they contain redundant or obsolete standards, and whether their intent is clearly stated; d) recommendation, for safety improvements and for revision and clarification (if necessity) of governmental regulations. Magazine explosions are rare. A recent increase in magazine explosion frequency must be attributed to a large increase in deliberate (criminal or malicious mischief) explosions. Fires of various origins account for the remaining explosions of the past decade. During 1884-1926 several lightning-generated explosions occurred in non-metal magazines, but none recently. It appears that the contents of a well-constructed, metal magazine are immune to direct lightning strikes, regardless of whether the magazine is grounded or not grounded. Grounding a metal magazine cannot be harmful, but it may well be superfluous. Magazines were observed at 34 widely separated mines and storage problems were discussed with personnel at these mines. In general, storage conditions and practices were found to be satisfactory. Usually, only small quantities of explosives are stored on mine property since most explosives are brought in by suppliers when needed. MSHA and BATF standards on explosive storage appear to cover safety aspects adequately. However, certain revisions are recommended to clarify some of these standards and to reduce inconsistencies in their enforcement.

Jan 1, 1983

Phase I of U.S. Bureau of Mines contract H01220S3, "Improved Sensors and Fire Control Systems for Mining Equipment, II was an investigative effort involving study of the fire problem and preliminary design of a fire protection system. Overall contract objectives included three basic efforts: * Identify problems * Develop a design * Demonstrate a system The first two efforts were conducted during the period June through November, 1972. Phase II will involve testing of system components; construction and testing of a mockup; and demonstration of the system on a truck to prove its effectiveness under actual operational and environmental conditions.

Jan 1, 1972

By Peter Murphy

This report (arid related appendices) provides a description of the functional design specifications, engineering design specifications, and program of instruction for development of a training system for dragline equipment operators. Based upon a task analysis and training system analysis prepared under Phase I, Phase II efforts expanded upon and refined the functional design specifications. The training hardware components have been developed to a point shy of system fabrication. A detailed outline of the porgram of instruction and content sequence has been prepared. The objective of the training system described in this report is to provide new operators of dragline equipment with the requisite skills and knowledge to assure cost-effective development and an adequate supply of our human resources.

Jan 1, 1976

By Forrest T. Moyer

The safety record of the coal-mining industry in 1968 worsened appreciably .in fatality experience but was slightly better in nonfatal-injury experience. Work fatalities in 1968 totaled 311 and occurred at a frequency rate of 1.33 per million man-hours or worktime. The fatality total was 89 higher, and the rate of occurrence was 45 percent higher than the corresponding figures of 222 fatal injuries with a frequency rate of 0.92 in 1967. The worsened fatality record in 1968 resulted primarily from two major disasters (a single accident which results in the death of five men or more) which killed 87 men, nine in one and 78 in the second. The total of 9,639 nonfatal injuries was the lowest annual figure in complete records back to 1930. The frequency rate of 41.12 nonfatal injuries per million man-hours of worktime for 1968 was the second lowest annual rate of occurrence. The severity rate of all injuries, 10,513 days lost or charged per million man-hours, and the average severity, 248 days lost per injury, in 1968 were the worst annual data in the series started in 1944. Total worktime of 234.4 million man-hours and coal output of 553.3 million tons in 1968 were, respectively, 3 and 1 per- cent lower than in 1967.

Jan 1, 1972

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. stone mining workforce from March through September 1986. Similar reports have been published for the metallic, sand and gravel, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

By W. L. Cooley

Electrical accidents occurring in coal mines from 1975 through 1979 were categorized and analyzed. The data was searched for common electrical hazards, common activities on the part of those injured, and common negligent or careless behavior. The most common electrical hazard was abnormal arcs or sparks, the most common injured activity was handling energized trailing cables, and the most common careless behavior was failure to de-energize circuits before working on them. The accident data was combined with mine production statistics to form a normalized electrical accident rate. It was found that some mines have consistently more lost workdays per man-hour worked than do other mines. Bureau of Mines electrical safety research contract expenditures were reviewed to judge whether the research effort was directed to those areas which are related to the most accidents. In some cases it was not. A method was devised and utilized to estimate the relative cost to the mining industry to implement certain safety measures developed through Bureau research, and also to estimate the potential safety benefits. Some safety changes are recommended, others are not. MSHA regulations were reviewed for effectiveness in preventing electrical accidents, and suggestions were made for discontinuing, clarifying, or otherwise modifying the regulations.

Jan 1, 1981

By W. H. Ode

In 1949 the Coal Committee of the Economic Commission for Europe, Geneva, Switzerland, established a Classification Working Party, to develop an international system for classifying coal. This project was necessitated by the increased trade in coal among various nations following World War II. Although national classification systems existed, they had been developed to cover the characteristics of domestic coals without reference to coals of other countries. Different terms for describing similar or identical coals in each nation caused confusion in evaluating coals shipped in international trade. Experts from Austria, Belgium, Bulgaria, Czechoslovakia, Denmark, the Federal Republic of Germany, France, Greece, Hungary, Italy, the Netherlands, Poland, Sweden, the Union of Soviet Socialist Republics, East Germany, the United Kingdom, the United States of America, and Yugoslavia participated in various stages of the classification work. Walter A. Selvig was appointed by the Bureau of Mines as the technical expert to represent the United States because of his experience in developing and standardizing methods of analyzing and classifying American coals. He served on the Classification Working Party until his retirement from the Bureau of Mines early in 1956. Extensive laboratory work was done in connection with the classification studies at the Pittsburgh Experiment Station of the Bureau of Mines.

Jan 1, 1958

By F. Matanzo

[Nine wire rope terminations were pull tested and fatigue tested to destruction to measure the termination efficiency and relative fatigue life. The terminations were selected on the basis off mine site visits and the specimen were assembled in a manner similar to industrial slings. To measure a termination's sensitivity to poor workmanship, both standard and modified assembly specimen were tested. Lang and Regular construction of the 6x19 and 6x37 class wire ropes were used in diameters of 13 mm (1/2 in.), 19 mm (3/4 in.), 25 mm (1 in.), 38 mm (1 1/2 in.), and 51 mm (2 in.). In static pull tests rope class, construction, and diameter interacted with the termination to influence the efficiency of the termination. In axial fatigue tests using only the 6x19 class rope, the effect of rope construction was negligible since failure was primarily dependent on the termination type. The Swaged Socket, a termination requiring a high capacity hydraulic press, gave the best overall performance in terms of efficiency and fatigue life. The short body length of the Zinc Poured Socket (RR-S-550) was attributed with the short fatigue life of this termination. The use of thermosetting resins as a replacement for zinc was demonstrated successfully for some socket designs. The fatigue life of the termination, expressed as a percentage of the fatigue life of the wire rope, was shown to be a guide for the retirement of the wire in these applications where the wiry' rope is primarily in axial loading.]

Jan 1, 1978

By T. H. Miller

An attempt has been mace in this publication to present annotated references to all articles pertaining, to ore dressing that were published during 1931 and 1932; in a few instances reference is made to articles published prior to 1931 where the articles have not been included in previous bibliography appended to the annual statistical discussions of ore concentration published by the Bureau of Mines. Articles have been taken from more than 75 periodicals, journals, serials, etc., and 423 articles are abstracted herewith. A number of these abstracts, particularly those appearing in foreign publications, have been taken from Chemical Abstracts (published by the American Chemical Society, Easton, Pa.), the general use of which the authors wish to acknowledge. Other annotations were taken directly from the original publications. The entire field of ore dressing has been included in the bibliography and articles dealing with crushing, grinding classification, concentration, thickening, and filtration have been included, as well as on amalgamation, cyanidation, leaching, magnetic concentration, washing, etc., and on theory and laboratory operation. The articles are arranged in alphabetical order by authors. Lack of printing funds prohibited the inclusion of a subject index.

Jan 1, 1934

By J. J. Taber

Gas and water permeabilities of a large number of samples from the Pittsburgh and Pocahontas coals were measured at various overburden and mean flow pressures. A wide variation in the air and water permeabilities was obtained for each type of coal. Overburden pressure has the most significant effect on the single-phase permeability. Considerable hysteretic effect was observed for both air and water permeabilities. Gas permeabilities are affected to a lesser degree by mean flow pressures above atmospheric. However, at subatmospheric mean pressures, appreciable increase in permeability occurs for low permeability samples. Air and water relative permeabilities were also measured for numerous samples of Pittsburgh and Pocahontas coals. Tests were performed under steady-state conditions for both drainage and imbibition cycles. Results indicate that the flow of gas is greatly reduced during the latter process, whereas it is largely undiminished over a wide water-saturation range during drainage. It is also shown that imbibition saturation distributions obtained from liquid-water imbibition as opposed to water-vapor adsorption produce gas permeability curves of radically different character. The effective permeabilities to both gas and water were significantly reduced with the application of overburden pressures in the range of 0 to 1,000 psig, but the general shapes of the relative permeability curves remained the same.

Jan 1, 1974

By William R. Wayment

The objective of this investigation was to obtain data on friction-head losses of sand slurries during their transport in pipelines. The data ultimately will be used in designing hydraulic transport systems. Information that was incidental to the primary objective was gathered on degradation, changed percolation characteristics, and critical velocities of the slurries~ Tests were made in a closed-circuit pilot plant, with one type of tailing, through horizontal 2-, 3-, and 4-inch-pipe test sections at various pulp densities and flow velocities. Tests were made in a closed-circuit pilot plant, with one type of tailing, through horizontal 2-, 3-, and 4-inch-pipe test sections at various pulp densities and flow velocities. Approximately 2,000 tests were run in the pilot plant. The ranges of flow velocities used in the experiment were 2.8 to 19 f.p.s. in the 2-inch line, 4 to 14.5 f.p.s. in the 3-inch line, and 4 to 11 f.p.s. in the 4-inch line. Velocities were varied in increments of 0.5 f.p.s. through the entire velocity range in each pipe size. Densities were varied in 3-percent increments from 40 to 70 percent solids by weight except for one series of tests in the 2-inch line; in this series, densities were varied in 5-percent increments from 5 to 65 percent solids by weight.

Jan 1, 1962

By J. R. Thoenen

[Before 1914 Germany held virtual monopoly on the world supply of potash for fertilizer purposes. During the world War, potash shipments to the United States ceased, and recourse was had to domestic supplies. High war-time prices stimulated interest n various sources, and domestic production increased rapidly. At the close of the war, resumption of shipments from Germany and other sources reduced prices to below pre-war levels, and, as a result, most of the domestic producers ceased operational.]

Jan 1, 1941

By Thomas M. Barczak

This US. Bureau of Mines report examines the roof and floor contact pressure provided by the interaction of a shield with the surrounding strata. Controlled forces were applied to an 800-ton two-leg shield in the Bureau's mine roof simulator; the distribution of forces acting on the canopy and base of the shield were measured with 24 hydraulic pressure cells. Several influential factors that affect the load distribution were investigated: (1) the magnitude of loading (leg pressure); (2) the profile of the canopy, principally the upward-sloping tip; (3) the base-lifting device; (4) horizontal load acting on the shield; and (5) compliancy of the immediate roof and floor. It was concluded that the shield does not develop full canopy or base contact without deformation of the strata. Maximum contact pressures are developed at the rear of the canopy and on the toes of the base. Less than 10 pct of the available shield capacity is developed at the canopy tip despite the design intention to ensure tip contact. Horizontal loading reduced the toe pressure acting on the base by as much as 75 pct. The base-lifting device exaggerated the inherently high toe loading, increasing the contact pressure by more than 200 pct.

Jan 1, 2010

By K. K. Kelley

Thermodynamics data for silicates have applications in the fields of extractive metallurgy, ceramics, and geochemistry. To facilitate these applications, up-to-date tables of heats and free energies of formation are needed. It is the purpose of this report to supply such tables for anhydrous silicates. During the last 15 years the heats of formation of a substantial number of anhydrous silicates have been reliably determined at or near room temperature. This resulted from the development (first by the Bureau of Mines and later by the Geophysical Laboratory of the Carnegie Institution of Washington, by the Institute of Geology of the University of Helsinki, Finland, and by the Department of Geology of the University of Chicago) of accurate solution calorimeters, employing hydrofluoric acid as the reaction medium. Specific references to work of these laboratories will be made in the next section of this report. Also, entropy data at 298.150 K. and high-temperature heat-content values are available for many of these silicates, mainly owing to work of the Bureau of Mines. Most of these entropy and heat-content data have been compiled in Bureau of Mines Bulletins (13, 15).3

Jan 1, 1962

By Loren R. Anderson

Traditionally, an evaluation of the safety of slopes has been based on computing a safety factor against failure. In computing the safety factor, the geometry of the slope, the soil parameters and the pore pressures are treated as deterministic quantities even though they are known to be random variables. A pseudo-three-dimensional probabilistic slope stability model has been developed that treats shear strength as a random variable. The model uses the probability of a slope failure as an assessment of slope reliability. The model can accommodate zoned embankments of soil in which the strength is described by the Mohr-Coulomb strength envelope. Autocorrelation functions are used to describe the spatial correlation of the strength parameters, c and tan ø. Model error can also be included in the analysis. The model has been applied to an existing tailings dam and to several hypothetical examples. These examples are presented to illustrate the influence of the choice of the soil strength variability parameters on the probability of failure. The results show that the critical failure surface based on the minimum safety factor is not necessarily the failure surface that will yield the maximum probability of failure. The analysis of the tailings dam shows that variance reduction can be large and that the model error is the dominant source of uncertainty for the embankment analyzed.

Jan 1, 1982