Search Documents

By Frank Sames

Ground vibration levels are generally predicted using equations such as the USBM equation implementing the scaled distance concept and describing geological and blast design parameters in a ground transmission constant.

Jan 1, 1995

By Xing Zhao, Michael A. Sutton, Vikrant Tiwari, Damien Bretall, Xiaomin Deng, William L. Fourney, Uli Leiste

The dynamic response of a thin aluminum plate subjected to both shallow and deeper buried blast loading was studied. Using a combination of high speed stereo-vision and three dimensional digital image correlation (3D-DIC), sequential stereo images acquired every 38.25µs during blast loading were analyzed to determine full-field deformations and plate motions (displacements, velocities and accelerations, effective surface strain and effective surface strain rate). Measurements indicate that the initial sheet deformation was highly localized for both shallow and deeper blast events, with extremely high velocity and acceleration values recorded during the earliest stages of impact loading. Full field strain and strain rate data indicate that well defined strain and strain rate “maxima” are created in the plate, with the potential of affecting the dynamic plate behavior as well as it local failure.

Jan 1, 2010

By Marcia Harris, Richard Mainiero, Michael Sapko

Since 1988, there have been 17 documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through ground strata into occupied enclosed spaces as a result of proximate trench blasting or surface mine blasting. These incidents resulted in 39 suspected or medically verified carbon monoxide poisonings and one fatality. To better understand the factors contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out studies in a 12-foot diameter sphere to identify key factors that may enhance the levels of CO associated with the detonation of several commercial trenching explosives. The gaseous detonation products from emulsions, a watergel, and ANFO blasting agents as well as gelatin dynamite, TNT, and Pentolite boosters were measured in an argon atmosphere and compared with those for the same explosives detonated in air. Test variables included explosive formulation, wrapper, aluminum addition, oxygen balance, and density. Major contributing factors to CO production, under these laboratory test conditions, are presented. The main finding is the high CO production associated with the lack of afterburning in an oxygen poor atmosphere. Fumes measurements are compared with the manufacturer’s reported IME fume class and with the Federal Relative Toxicity Standard 30 CFR Part 15 in order to gain an understanding of the relative toxicity of some explosives used in trench blasting.

Jan 1, 2003

By Don W. Lake

Of all the blast monitor& instrumentation systems and techniques av&able today, highspeed photography and videography remain as the most valuable, stand alone, diagnostic techniques to evaluate full scale blasts in the mining and explosives industries. Highspeed image data, coupled with information from other instrumentation systems, such as continuous VOD records, seismographs, laser surveying systems, refraction seismographs, etc. can eIiminate many assumptions about what actually took place in a blast. Thus, diagnostic confidence in evaluating both good and bad blasts is increased, and optimum blast designs are achieved considerably faster when compared to the trial and error approach or relying on just the experience factor.

Jan 1, 1992

By Ralph E. Burnham, Jeff Taylor, Jonson Montgomery, J. Kelly Ratliff, Rennie Montgomery, Martin Brashear

Top priorities for all blasting companies and individual blasters are risk management, safety of company personnel and the general public, regulatory compliance, and liability protection. On a daily basis, hundreds of shots are detonated by well-trained, skilled, and experienced blasters without incident. Unfortunately, accidents inevitably occur, which is why blasting is considered an “ultra hazardous” or “inherently dangerous” activity from a legal perspective. Despite countless regulations, recent advances in technology, improved training, ongoing research, and improved communication in the industry, mistakes and the resulting incidents continue to occur during blasting operations. These result in dangerous or deadly flyrock, site security lapses, increased complaints, blast damage claims, and lawsuits, which lead to increased insurance costs and other financial tolls for blasting companies. In life, lessons learned the hard way are rarely forgotten. The same is true in blasting operations. Blasting missteps and the resulting events are often the best catalysts for improving risk management and thereby reducing accidents, liability, and financial tolls. This paper provides a summary of two incidents, one safety and the other liability related, and the errors that resulted in a fatality in one case and a multi property lawsuit in the other. The two incidents provide examples that serve as a case study for lessons learned the hard way in blasting operations and offer guidance for the considerations that blasters and blasting companies should incorporate into daily operating procedures.

Jan 1, 2018

By N. Jayaraman, V. Srikant, A. Radhakrishna

Addition of a 500 MW unit to the existing units at Ramagundum Thermal Power Station requires blasting of large volumes of rock very close to sensitive installations like Turbo generator, Generator transformer and Power cycle equipments. Levelling of the areas and excavations for footings are, therefore, to be carried out cautiously. The existing sensitive installations should be protected against ground vibrations and flyrock. The paper describes the details of a few of the many blasts carried out successfully wherein the ground vibrations were restricted and flyrock was avoided.

Jan 1, 2003

By Dennis L. Paisley, Thomas P. Turner

Laser slapper detonators are the next generation detonator under development at the Detonations Systems Group at Los Alamos National Laboratory and function very similarly to an electrical slapper. A fiber optic transmits a laser pulse to ablate a thin metal film. This film, or flyer as it is commonly called, is launched through a short barrel to km/s speeds. The flyer shock loads or slaps a high density pressing of secondary explosive, setting off a detonation therein. Laser slapper detonators afford a number of safety advantages over other conventional detonators. Most important they require very high peak laser powers to operate, orders of magnitude larger than possible sources of natural or man-made accidental stimulus. Because light is transported over fiber optics, laser slappers avoid many of the electrical hazards associated with detonators. Use of insensitive, secondary explosives makes these detonators safer to handle, manufacture, transport, and deploy.

Jan 1, 1994

By Alex Chapman, Cam Thomas, Bryan Karney

"During the early summer of 1989, Ontario Hydro removed a concrete portion of the North Channel Dam at Crystal Falls Generating Station by blasting and excavating in marine conditions. Because of the severity of underwater blasting and because the site was in close proximity to the replacement dam, there was concern that hydraulic shock waves generated by the detonation could damage either the new dam or its control structures. This paper examines the data associated with the hydraulic shock waves generated by underwater blasting, and studies the effectiveness of an air curtain in reducing the peak pressures. In previous trials using the air curtain technique, a rule-of-thumb factor was used to estimate that only 10% of the original pressure pulse would propagate across the air curtain. However, this value had little basis in theory. A theoretical formulation of the problem by Karney in 1989 indicated a provisional value of 0.18 for this factor, but was heavily dependent on confirmation from in-field testing. Data provided by Ontario Hydro from an actual blasting procedure indicate that a more conservative value of 0.32 may be more appropriate. Thus.although the air curtain did provide considerable reduction of peak pressures, the data at Crystal Falls indicates its performance was below the anticipated level. However, due to problems with the instrumentation and some inconsistencies in the resulting data. it is recommended that this value be further refined as additional data become available."

Jan 1, 1992

By Tom Treleaven, Andrew Williams

Several contracts were let in Greenwich, Connecticut, for the installation of a sanitary sewer. The majority of the excavation was in rock and involved numerous challenges due to the following conditions:

Jan 1, 2003

By AJ Rorke, JD Botes

Presplit blasting in strip mines is aimed at creating a safer wall to work under during the coaling operations. Good quality presplits are also necessary for effective throw blasting and drainage of the blast block. A less obvious but important function is full coal recovery. Optimum Colliery has been experiencing rock freezing against the presplit highwalls. The rock formed in patches along the highwall and trapped coal beneath it. The material that was &ozen comprised the rock between the back row of holes and the presplit and was often up to 3 m thick (the stand off distance between the back line and the presplit). The cozen rock formed predominantly along the bottom halfor bottom two thirds of the highwall. Along the top portion of the highwall, the presplit crack was usually well formed with visible barrels. This problem, or similar variations of it, is common on many South African strip-mine operations. Investigative work was carried out at Optimum Colliery to correct the problem. This paper presents the information and measurements that were made and discusses the solutions that have been applied to solve the problem. It was found that there were two independent causes for the tiozen material, with each contributing more or less to the frozen rock along the highwall. It was found that the presplit was not forming properly in places, especially closer to the bottom of the highwalls. The reasons and the solutions are presented. The second cause was found to be associated with reduced detonation velocity in the back line holes coupled with low confinement from long delay periods. Emulsion explosive that is sensitised with air bubbles was found to be prone to this phenomenon near the back of high-energy blasts. A change in the explosive formulation in the back-line holes, together with reduced delays in the back line, has resulted in significant improvements. The details are presented in this paper.

Jan 1, 2000

By J. Lindenau

One of the significant benefits of electronic detonators is their safety, especially their relative insensitivity to extraneous electrical energy. The various brands of electronic detonators on the market have different resistance to electrical stimuli, but all have safety structures designed to afford a significant level of protection. A common source of extraneous electrical energy is lightning. This paper discusses the nature of the energy that occurs with a lightning strike and the resistance offered by electronic detonators. Four actual cases of exposure of electronic detonators to lightning strikes are considered. Electronic detonators, like other initiation systems, are vulnerable to very close or direct lightning strikes. The incidents are a reminder that all blast patterns need to be vacated on the approach and during the progress of a lightning storm. 1. Orica

Jan 1, 2008

By M Thierry Bernart

The software QUALITIR is a software developed by CNSIDCI, framework on five research and experimentation years. This conceived tool by specialists for professionals is a decision aided design tool concerning mining. It makes party the rare software regrouping the different themes approached by the profession namely, the general idea of blast design, blasting sequences, the fragmentation as well as the study of vibrations. Henceforth it is by the intermediary of such tools that performances in term of profitability, security or impact on the environment will be able to be realized.

Jan 1, 1997

By Jeon Jeon, Yong-Kun Choi, Chung-In Lee, Yong-Hun Jong, Hag-Soo Kim

In this study, a computer program to design tunnel blasting pattern has been developed. The program consists of two parts; one is for tunnel blasting pattern design and the other is for blasting modeling to estimate the peak particle velocity, the distribution of fragmentation and the excavation damage zone. We modified the design method of tunnel blasting pattern suggested by Langefors because it provided undesirable pattern in blasting practices such as considerably large center cut and too large burden for Vcut as drilling length increased. As a result, the burden and spacing were reduced to practically appropriate amounts. In addition, the correlation between rock mass rate, RMR, and rock constant in blasting, c, was analyzed based on the data collected from twenty three tests of tunnel blasting. It was concluded that the correlation between them was fairly good enough to be applied in cut design. In order to check the validity of the modified methods and their practical applicability, test blasting was carried out at two different tunnel construction sites in Korea. The results were satisfactory in that the average rate of advance was 90% and the overbreak did not cause additional support. Futhermore, the developed program is capable of estimating peak particle velocity by using (a) the existing vibration equations, (b) the vibration equation obtained by test blasting to check out the practical applicability of the designed blasting pattern. Feedback is implemented into the program to adjust the designed blasting pattern and control the vibration.

Jan 1, 2005

By D. Scott Scovira, Ruilin Yang

Blast vibration in the highwall from a cast blast in open pit mines or in the hanging walls from a stope blast in underground mines is a common concern. Vibration in such cases is a typical near-field situation where the distance from a blasthole to a point of interest varies significantly compared to the distance between the blast as a whole and the point of interest. Most existing blast vibration models are designed for far-field vibration using a single seed wave to represent all blastholes within a blast and do not simulate wave shape change over the distance.

Jan 1, 2010

The common approach of designing blasts on a trial and error basis is quickly coming to an end. When utilizing the full scale blast environment, trial and error can quickly become cost prohibitive and leaves much to be desired in terms of true blast diagnostics. In these situations testing is usually only continued until a perceived improvement is achieved and when the gross undesirables in blast results are removed. This does does not preclude, however, that further improvements of up to 100% or more can not be obtained.

Jan 1, 1991

By Cam Thomas

The initial application for reflectorless laser technology was for profiling rock faces to determine front row burden and improve flyrock control and airblast. Over the past fifteen years a number of laser systems have been developed for general ground modeling purposes and GPS offsets, but these advances have yet to gain common acceptance in construction, mining and quarry blasting. This paper will outline a number of applications for reflectorless laser technology, including the latest method for rock face profiling, mapping, and 3-D modeling to calculate available and excavated rock volumes. Drilling deviation measurements will be presented in conjunction with rock face profiling to demonstrate how this information can be used to improve blast results. In complicated excavations, the actual quantity of rock excavated for payment purposes and the amount of overbreak can be very controversial. Procedures to calculate these volumes using laser technology will be outlined and comparisons will be made between these results and traditional techniques.

Jan 1, 2003

By Tom Short

"Construction blasting covers a very extensive variety of explosive applications. I will discussseveral of these with you and then show slides from my collection, starting in 1956, which will betterillustrate the types of blasting under discussion."

Jan 1, 1991

By Conny Postupack

To make money in mining coal you have to sell it for a lot more than it cost you to get it out of the ground. And yet, every year it cost us more and more to stay inbusiness, while the price we get for coal does not increase at the same rate.

Jan 1, 1990

By Brian Wingfield, Greg Williams, Richard W. Givens

Application of required energies into the rig design can have a dramatic impact upon productivity. Computer modeling of these production variables has led to changes in design with values closely approaching actual field data. Knowledge of these required energies can also specify the proper drilling technique to the application. With this knowledge, productivity-to-cost ratios can be determined with the most efficient option chosen.

Jan 1, 1995

By Ron Lutz

In today’s world, production is the name of the game. We are all in business to make money. In the Quarrying and Mining industry the same holds true. The primary goal is to develop the best drilling and blasting program available to maintain uniform fragmentation to maximize production. Also we want to maintain drilling and blasting costs and minimize escalators. This paper is intended to discuss ways for all parties (quarry’s, blast service and drill companies) to attain this through understanding what can be done to help blasthole drilling and production. Blast designs and seminar’s emphasize the accuracy of drilling to produce better fragmentation. Blast design must also include basic concepts in the drilling process. The type of drill to be used for example whether it is a crawler or truck mount, top hammer or down the hole is important. Quarry operators have a role to play as well. They hold the key to the production of drilling. What the customer does or does not do has a direct effect financially to the drilling. The phrase of pay me now or pay me latter comes to mind. This paper will explore the detail of planning that is required by the quarry and/or blast service companies before a single hole is drilled. The drill must be able to meet the production need of the operation. The type of drill available and what can and cannot be done. The drill cost must be competitive. This paper will touch on comparison drill costs from 1967 to 1999.

Jan 1, 2000