Search Documents

By Qingwei Joshua Ong

Tension piles, also known as uplift or anchor piles, are necessary to resist uplift forces that might cause structural distress. In excavation projects, most uplift forces are developed because of hydrostatic pressures, and so tension piles are subjected to a great deal of tensile forces. Most current methods of design for tension piles completely neglect the tensile strength contribution of concrete, relying only on the steel members to carry the tensile stresses, resulting in an overly conservative design. The stressstrain behavior of the composite material of concrete and steel must be considered for a realistic simulation of tension piles. This paper will examine a case on a tension bored pile in typical soft clay to demonstrate the importance of considering the tension strength and tension softening of the concrete.

Nov 1, 2022

By Sam X. Yao

In construction of drilled shafts under water, placing concrete in the shafts is technically demanding and involves complex construction logistics. Past construction experience has demonstrated that high quality concrete can be placed in drilled shafts under water with a proper concrete mix and proper placement techniques. However, a significant number of failures have occurred which have resulted in excessive cost overruns and delays. These problems may have occurred because proper underwater concrete construction techniques have not been widely disseminated within the industry. This is a technical area where competent design and sound construction planning can achieve a significant reduction in both risk and cost. This paper will discuss some key technical issues in the concrete mix design, concrete production and placement for the drilled shaft construction. The paper also describes two lesson-learned case histories from drilled shaft construction projects.

Jan 1, 2013

By James S. Graham

Marine design and construction methods are presented on the caisson foundations for the tower piers at the Brooklyn, Ben Franklin, Delaware Memorial 1st, Tappan Zee, Walt Whitman, Throgs Neck, Verrazano Narrows, Delaware Memorial 2nd, and Newport Bridges. All of the bridges are founded on caissons, bearing on bedrock, soil, or piling. Caissons at the Tappan Zee Bridge are partially supported by piling and partially by buoyant forces. General subsurface conditions for each are provided. The purpose of this paper is inform engineers how bridge foundations using caissons were built over major waterways in the Northeastern USA in the past, anticipating a surge of new bridge construction in the near future.

Jan 1, 2013

By Garland Likins

High strain PDA testing has become common for verification of capacity of both driven and bored piles. It is equally applicable to Augered-Cast-in-Place (ACIP) Piles. It also evaluates other aspects of the installation such as integrity. The benefit of high strain dynamic test results for the relatively low cost of the tests compared to conventional static testing has resulted in widespread use. The method is described and specific procedures for testing ACIP piles are outlined. Example results demonstrate the application.

Jan 1, 2000

By G. W. Plant

This paper describes the design philosophy and construction details of piles between 25m and 32m deep to support 160m high and 110m base diameter cooling rowers for a major power station. It is sited on deep expansive soil where a vast plantation of Eucalypts had been felled. The depressed water table is expected to rise, leading to swell of the soil and uplift forces on the piles. These forces, combined with the complex loading from the cooling towers, led to design tensile loads up to 20MN (2 000 tons) per pile. When competent stable material was present hand excavated underreams 3m in diameter were constructed for the piles sup-porting the shells. However, in some areas it was not possible to form an effective underream and an innovative solution was sought. This comprised unstressed dowels in the underlying sandstone which were formed by percussion drilling through void formers cast into the piles.

Jan 1, 2010

By E. W. Raabe

The paper discusses the increasing role of specialist grouting techniques to form water seals or cut-offs for deep basement construction. Raabe and Toth discuss the various grouting methods available for sealing applications and then concentrate on the use of Soilcrete Jet Grouting, a system particularly well suited to ground water control. The Soilcrete processes, suitable soil types and quality control methods are fully described, particularly with regard to the formation of cut-off walls and sealing slabs to prevent the progress of ground water or leachates. The authors have included case histories detailing their experience on designing and installing Soilcrete seals for various projects in West Germany. These include an underground rail project in Dortmund and a discharge structure for the Alz Canal at Burghausen.

Jan 1, 1989

By J. G. La Fonta

The rapid development of real-time monitoring technology for the construction of large underground structures in urban areas can be attributed to: the zero-risk objective, the need for transparency between all parties involved and the control of real cost within the budget. Real-time monitoring can be an integral part of the construction contract (for example when compensation grouting is required) or independent, in particular when measurements of existing structures and buildings bordering the project are to be taken before construction starts. Three examples of extensive field instrumentation schemes are described: a large road tunnel in the Moscow suburbs, a new metro line in Amsterdam and major redevelopment works at a busy Central London rail interchange.

Jan 1, 2006

By Jeff Wilkinson, Brandon Walter

"A&N Electrical Cooperative provides electrical service to the counties of Accomack and Northampton along Virginia’s Eastern Shore and to Smith Island in Somerset County, Md.A&N recently worked to improve the efficiency of power distribution to a small island community and marina on Tangier Island in the Chesapeake Bay. This improvement consisted of upgrading the existing distribution substation with a new 25 kV 2-bay box distribution structure. Earth Contact Products (ECP) collaborated with PowerServices, Inc. (PSI) to design and install a helical foundation support system as part of the substation upgrade. Feasibility EvaluationThroughout the design process, A&Nworked with its partners PSI (design) andT&D Solutions (installation) to identifycost-effective alternatives. Foundationsystems considered included cast-in-placereinforced concrete caissons, precastconcrete foundations, driven steel piles and helical piles. In evaluating all of theoptions, the greatest concern was gettingthe material onto the island, followedclosely by the availability of the equipmentto install the foundations. Clearly, cost,more specifically the installed cost, was asignificant consideration and decisionfactor throughout the process.There were several limiting factors that had to be considered during the design process, the most significant of which was that all of the material had to be barged to the site. With traditional reinforced concrete deep foundations in mind, the cost for installing these piles was projected to be nearly $2,000/cu yd ($262/cu m) of installed concrete. Given that approximately 5 to 6 cu yd (3.8 to 4.6 cu m) of concrete would be required for this structure, the cost was significantly high for this project. What’s more, because the components of the concrete mix would have to be barged and then hand mixed on site, there was concern regarding both the time required to complete the piles and the quality of the installed concrete. For the driven pile alternative, the availability, or lack thereof, of equipment and material cost resulted in a total cost estimate that was more expensive than that of the concrete piling alternative. The high material cost for the piles, which was more than double than the cost of concrete, was due to the number and size of piles needed to resist the overturning moment. Ultimately, the team selected the helical pile alternative. The decision to a use helical pile foundation system was based on many factors, not the least of which was the remote location of the project site and the difficulties associated with getting material, equipment and construction personnel to the project site."

Jan 1, 2017

By Gokhan Inci

Stability problems with dam spillways on existing landslides and appropriate mitigation measures to remedy them are ongoing concerns for geotechnical engineers. The first successful application of drilled piers as stabilizing structures under the spillway was at the Trinity Dam in Sicily, Italy. ?Underpinning? was considered as an alternative to spillway relocation during the Alpaslan 2 embankment dam design in eastern Turkey. Based on the available literature the first application of drilled piers to stabilize a spillway chute in the U.S. was at the Ralston Dam in Colorado. Ralston Dam, which is a 175-foot-high zoned fill dam located 15 miles northwest of downtown Denver, was built in the late 1930s. The concrete spillway for the dam was built on the Pierre Shale Formation in the left abutment. Since reservoir operations began, mass movements have occurred downstream of the chute area. These movements have required periodic spillway maintenance. After the occurrence of recent movements and because of high piezometeric levels, URS was contracted by Denver Water to develop a more permanent solution by the installation and monitoring of additional instrumentation, analysis of slope stabilizing measures, design, repair, and reconstruction of the distressed section of the spillway chute. With state of the art modifications that include: 1) a stabilizing berm with a toe trench that improves the global stability; 2) seepage prevention and control measures that prevent the infiltration of water; and 3) the structural support of the replaced chute section with drilled piers and reinforced concrete the probability of future displacements or other problems have been reduced for the Ralston Dam Spillway.

Jan 1, 2007

By Michael T. Lambert

The purpose of the this paper is to demonstrate the benefits of using additional instrumentation during load tests of auger-cast-in-place piles. Traditionally, only load and butt displacement are determined during load tests. The results from and methods used to instrument 15 auger-cast-in-place (ACEP) piles as part of six projects are included herein. By instrumenting the piles, the distribution of load along the pile length and load transfer can be determined, allowing the pile capacity to be adjusted or the length/diameter of the pile to be adjusted for the a given required load. The majority of the piles tested were designed as end bearing piles on either shale or limestone bedrock. No discussion of Geotechnical Instrumentation can be started without acknowledgement of the "Red Book." The actual title of the book is Geotechnical Instrumentation for Monitoring Field Performance, by Mr. John Dunnicliff, John Wiley and Sons, 1993. Anyone undertaking an instrumentation program should thoroughly review the Red Book, paying particular attention to Chapters 3 and 4. Instrumentation should not be done just because it can be done. There must be an unanswered question or questions that can be answered with measured data before instrumentation should be considered.

Jan 1, 2000

By K. E. Darnell

Drilled pier foundations have long been a favored foundation type for heavily loaded structures. Drilled piers derive their load-bearing capacity from end-bearing, and/or sidewall friction. This type of foundation is used in many geologic settings, including those areas underlain by hard carbonate rock, such as limestones and dolomites. When properly designed and constructed, drilled piers provide high load-carrying capacity in both compression and uplift. However, carbonate rock is often subject to intense differential weathering resulting in the formation of an irregular bedrock surface, sinkholes and caves; consequently, the investigation for, and the design of, drilled pier foundations is often complex. Further, the construction may be difficult and costly. This paper discusses geotechnical investigative procedures which can be employed to develop foundation design criteria and reduce the frequency of changed conditions. Finally, state-of-the-art construction practices and quality control techniques are discussed.

Jan 1, 2010

By Dinesh Hinduja, Pérez: Miguel

"Large structures are generally exposed to dynamic and structural loading. They require usually either foundation connected to hard rock through sockets or driven foundations, which encounter boulders as well.In this regards drilling hard-rock sockets or boulder offshore or onshore can be a challenging job especially when deep foundations are mandatory. To overcome the challenge, specialized equipment like a Pile Top Drilling rig (PBAs) can be used, which have to be correctly set-up and operated in order to get its maximum drilling performance. High performance drilling with PBAs requires maximizing key elements of its operation. The configuration and management of the drill string components are important. The key elements are constant weight on bit which is done by adjusting ballast and managing thrust force; and selection of cutters and proper flowing discharge.The methodology is based on the experience from over 40 years of building and operating PBAs for different project applications. These applications include drilling offshore and onshore for:?Superstructures and buildings?Drilling platforms, barges and jack-ups?Harbours, jetties, dry docks and dolphins?Bridges, piers and causeways?Marine sewerage diffusers?Offshore wind farms?Dam rehabilitationMHWirth documented methodologies demonstrate that by using PBAs properly it is possible to improves performance of underwater drilling for hard-rock sockets and boulders which ultimately reduces project-cost.Background. There is a significant percentage of total project cost in structural foundations. Equipment capabilities and technics to drill shaft with rock-sockets and embedded boulders onshore and offshore are highly developed due to the dramatic equipment advancement and experience in the last 40 years. Formerly, driven piles accounted for the majority of foundations either onshore or offshore, following the experience of previous practice in the market. Nowadays, deep drilled foundations can be constructed to carry the load through the overburden down to the sound load carrying rock or soil.Scope and objectives. The overall objectives of this study are:?Synthesis information on current practices to drill shaft with rock-socket and/or embedded boulders onshore and offshore with Pile Top Drill Rigs?Identify the principal challenges evolving with practice?Provide suggestions for improvements in the construction of drilled shafts through proper operation of Pile Top Drill Rigs?Convey information through case studies and experiences"

Jan 1, 2015

By Ed Kase

Cross-hole sonic logging (CSL) has become the universal standard, nondestructive testing (NDT) method used in evaluating the integrity of foundation structures to maintain quality assurance and quality control (QA/QC) of transportation facilities and infrastructures. Tomography, based on three-dimensional cross-hole sonic logging data processing technology, offers an improvement over the techniques currently used to characterize the interior structure of drilled shafts. The underlying concept for seismic tomography is based on the principle that acoustic waves propagate at different velocities through different types of material or the same material with different physical properties. Three-dimensional velocity tomographic images provide greater detail of the interior structure, making defects easier to classify with respect to size and location within the foundation structure. By accurately classifying these defects, an engineer has the information necessary to accurately assess whether these structures meet the applicable design requirements, allowing them to repair or replace inadequate foundation structures. The end result is that the foundation structures will meet the safety and service life requirements for their project. This paper will present applications of seismic tomography, illustrating how seismic imaging can provide accurate information regarding the integrity of foundation structures.

Jan 1, 2003

By Matthew Janes

The RC Harris Filtration Plant, which treats the majority of the fresh water for over 2.5 million Torontonians, is a Canadian Architectural Heritage site demonstrating a classic example of Art Deco Architecture. The facility is undergoing an expansion to install an underground sludge treatment capability. Perched atop a bluff on the North shore of Lake Ontario the structure enjoys a commanding presence on the Lake Ontario shoreline. A series of underground tanks were proposed for the hillside below the structure, which when covered would preserve the building?s architectural presence. However, the plan required two, stepped excavations 12 m and 10m deep into compact, wet sands over stiff clays and clayey silts. Concerns regarding the original structure influenced designers to set the lateral deflection limit for the front footing of the existing structure at 4 mm, (0.03% excavation depth). The design-build team indicated at the time of tender that the movement criteria was unattainable using the tender design. Analysis indicated installation effects and overall elastic movement of the soil mass beneath the building would result in movements of 7 to 9 mm at the structure. Through extensive FLAC analysis and a novel construction geometry the design-build team crafted an alternative that produced significant savings over the original concept. Based upon the analysis the design-build team negotiated a new deflection criteria dictating a maximum of 2.0 mm of movement across the critical expansion joint between the Filter Building front footing and the tank slab beyond. The contractor invested in additional pre tender soils investigation to support the refined design process. The FLAC analyses indicated the Filter Building movements would be elastic and distributed up to 50 m back beneath the front footing of the structure. An extensive precision monitoring program proved construction related movements of 6 to 10 mm horizontal at the front footing. Extensometers placed at two locations over the critical interior tank expansion joint showed no measurable movements. The overall monitoring program, including inclinometers, tilt meters, tie back extensometers (smart cables) and tie back load cells indicated a good match between recorded movements and loads and those predicted by FLAC Analysis.

Jan 1, 2006

By Aly Mohammad, Dongyi Yue

"The design of rock sockets for drilled shafts and piles proves to be a challenge for the Design Engineer. The magnitude of loads on the shaft and the behavior of the rock are critical in determining the required socket length. Several acceptable methods are available in the literature to analyze a rock socket under a combination of axial loads, lateral loads and moments. This paper will present a state-of-the-art methodology to analyze rock sockets utilizing deformation characteristics of the rock. This design methodology was implemented in the design of a major project in New York City.The project discussed herein is a marine transfer station planned for construction at East 91st Street along the East River in Manhattan. In order to support the piers and platform structures at a site with relatively shallow depth of the bedrock, rock sockets were required for the drilled shaft foundations. Rock sockets were utilized to provide the required fixity to the foundations and the structures. Acting at the top of the rock sockets are large shear forces and moments created by the lateral loads transferred from the structure.Upon review of the available techniques, a simplified method was proposed and used to analyze the rock sockets with a significant magnitude of lateral loading. The method recognizes two mechanisms through which the lateral shear and moment are transferred to the rock; a) load transfer through horizontal resistance of rock and b) the vertical shear resistance of the bond between socket and rock.The first load transfer mechanism was analyzed using the p-y curve method based on a rock model developed by Reese. The second was analyzed using a bond stiffness derived from the formula and curves utilized in the AASHTO Specifications for calculation of rock socket displacement. By comparing the two mechanisms, the main contribution to the large horizontal shear force that developed in the rock socket is identified.The paper will present a summary of the design methodology utilized in determining the length of the rock socket. It is believed that the presented method will provide substantial cost saving in selecting the most economical and efficient design length."

Jan 1, 2005

By Djk Arentsen

A new technique to drive tubular piles by impact hammer inside the pile has confirmed a dramatic reduction of noise and the opportunity to save steel. Also a reduction in driving time and a higher bearing capacity has been observed during a test program of this technique. As part of the so-called "Down-the-hole" driving technique, a wave equation analysis has been developed to calculate driveability and pile stress. The main feature of the new "Down-the-hole" technique is the development of a patented device allowing uncoupled penetration of pile tip and pile shaft, which makes it possible to drive both closed or open end piles and reduce the stress level induced in the pile wall. During a test program, a number of instrumented piles were driven and compared with traditional driving of the same pile with the same hammer on top (also instrumented). Also the stresses and performances were compared with precalculations. This paper, explains the technique and presents the test and noise results, in comparison with traditional top-pile-driving. The "Down-the-hole" driving technique is an interesting alternative for special applications where traditional pile driving requires a large wall thickness or in areas where noise is a hot item.

Jan 1, 1996

By Beim Jorge, Piscsalko George

"Verifying the quality of cast-in-place foundation applications, particularly those cast under slurry, is of course important, due to its great dependency on the methodology employed and on the practices of the site personnel. Due to the techniques used to install these elements, it is usually not possible to inspect the hole prior to grout or concrete placement, but there are several Non Destructive Test (NDT) methods available to assess the integrity of the completed foundation elements. This paper will compare several NDT methods with the Thermal Integrity Profiling (TIP) method for verifying the integrity in Continuous Flight Auger (CFA) piles and Bored Piles. The Thermal Integrity Profiling method will be described and some examples will be presented where TIP testing was used to confirm the structural integrity of CFA piles and Bored Piles.IntroductionThere are several Non Destructive Test (NDT) methods available for integrity testing of foundation elements. Each of those methods has advantages and disadvantages (White et al, 2008). Some methods test the integrity based on the reflections of a stress-wave generated by low or high-strain impact, while others require tubes to be installed prior to concrete pouring, and test the integrity between those tubes, or within a small proximity of them. The former methods (especially the low-strain) are faster and more cost-effective, but are not able to detect the quadrant where the damage is located. The latter methods are able to determine the quadrant, but do not test the region outside of the reinforcing cage, that is, they are not able to determine the concrete cover. The Thermal Integrity Profiling (TIP) NDT method overcomes the limitations of these other NDT methods.Overview of Shaft Integrity MethodsUntil now, the most widely used methods to test the integrity of Bored and CFA piles were the low-strain pile integrity testing and the cross-hole ultra-sonic testing. The low-strain method for integrity testing (PIT) involves attaching an accelerometer usually to the pile top (using a putty or wax) and striking the pile surface with a handheld hammer, which causes a compressive wave to enter the pile. This wave is totally reflected when it reaches the end of the pile or a major defect, and is partially reflected when it encounters any change in crosssection, or a change in the resistance or density of the pile material. These reflections arrive at the top at a time determined by the distance and wave speed, and causes a noticeable change in the signal detected by the accelerometer. The acceleration signal is normally converted to velocity by simple integration, and sometimes the force applied by the hammer is also measured. The velocity (and force) signals can be processed by the pulse-echo method (in the time domain) or by the transient response method (in the frequency domain)."

Jan 1, 2015

By John L. White

The vibro driver/extractor is a machine that grips to a pile and vibrates it up and down. When the vibrating pile is lowered into the ground, all soil around the pile begins to vibrate. A vibrating pile breaks the friction between the pile and the soil, thus allowing it to penetrate the ground. A vibro is usually operated by hoisting it into the air with a crane and then placing it onto the pile. The vibro has hydraulic gripping jaws that are controlled from the ground. Once the operator has successfully lowered the vibro onto the pile, the jaws are closed and locked onto the pile and operations can begin. Please see the drawing below: [ ]

Jan 1, 1990

By T. G. Davies

The paper presents design equations for singly laterally loaded piles embedded in sand. These equations were obtained from a comprehensive nonlinear analysis of free and fixed head piles subjected to horizontal loads. The sand is modelled as an elastic-perfectly plastic material whose strength and stiffness are proportional to depth below ground level. The soil's response is described by means of a boundary element representation of the continuum while the pile itself is created as an elastic beam. Equations for the latter are derived directly from the Bernoulli-Euler theory and are coupled with those describing the non-linear soil response. The effects of bearing failure along the front, face of the pile, shear failure along its sides and tension failure at the back face are accounted for in the analysis. Simple equations are presented to describe both the elastic and inelastic responses. The only sol parameters required to use these equations are the angle of internal friction of the sand and a parameter characterizing the rate of increase of the sand's modulus with depth. The latter can be taken as equivalent to the modulus of subgrade reaction. The results of this analysis show that soil yielding is very significant at working load levels, resulting in substantial increase in bending moments and lateral deflection.

Jan 1, 2010

By Theodore W. Vogelpohl

Augered cast-in-place piles have proven to be effective, adaptable and economical for projects throughout the Ohio River Valley. Specifically, they have been used extensively for high-rise structures, sports stadia and large commercial developments along the Cincinnati, Ohio and Northern Kentucky Riverfront. They have been designed and utilized as relatively short toe resistance piles in bedrock, and intermediate to long toe and shaft resistance piles in granular outwash deposits above the bedrock. They have been designed for large axial compression loads as well as moderate axial tension loads and lateral loads. This paper presents a few load test results that demonstrate the range of capabilities of augered cast-in-place piles in the variable subsurface profile along the Cincinnati, Ohio/Northern Kentucky Riverfront.

Jan 1, 2005