Search Documents

By E. Peek, L. Becze, K. Reading

"Gallium oxide is an important semiconductor material used in optoelectronic devices (flat panel and solar cell) catalysts and sensors. One of the methods to produce ?-Ga2O3 is the so-called hydrothermal route. It is practiced by Neo Gallium Compounds and comprises of two steps: (1) the production of mainly gallium-oxy-hydroxide in a pressure vessel by reacting metallic gallium with water at 200-220 ºC and (2) the calcination of gallium-oxy-hydroxide at 700-750 ºC to convert it into ?-Ga2O3. This paper describes this pressure hydrometallurgy process supported with relevant thermodynamic data and presents the characteristics of the ?-Ga2O3 powder produced for commercial purposes. INTRODUCTIONGallium is a relatively new metal, having been predicted by D. Mendeleev in 1871, discovered by P.E. Lecoq de Boisbaudran in 1875, and first commercially produced in the USA in 1943. Gallium is not rare, being more abundant in the earth crust than antimony, bismuth, molybdenum, silver and tungsten. However, few gallium minerals exist in nature, and the dispersion of gallium within other minerals add to the complexity of its recovery. In practice, gallium is found in dispersed state primarily in bauxites and in some sphalerites, and, to a much smaller extent, in some coals. At present, a very large proportion of the primary gallium in the world is recovered as a by-product of aluminum plants, mostly Bayer plants, where gallium is extracted from a bleed of the Bayer liquor (Roskill, 2011). In 2011, world production of primary gallium was estimated at 200 metric tonnes. In addition, there is a significant contribution of recycling to the overall yearly availability of the metal.Gallium exhibits fairly remarkable properties: it is liquid above 29.76 ºC, can be supercooled, and with its high boiling point (2204 ºC), is the metal with the widest liquid range. Gallium is magnetic, and is an excellent conductor of both heat and electricity. Gallium also displays a marked anisotropic electrical conductivity (Roskill, 2011). All these properties render gallium almost irreplaceable in the semiconductors (GaAs, GaN, GaSb, GaP wafers) and the optoelectronics industry (flat panel, solar cell)."

Jan 1, 2012

By G. Goodall, D. Mercier, M. Brochu, C. Kaplin

A nanostructured CoNiCrAlY coating was obtained by thermally spraying cryomilled feedstock powder using the high-velocity oxy-fuel (HVOF) process. The oxidation behavior of the nanostructured powder and coating were compared to their conventional counterparts by performing static oxidation tests at 1000°C for durations ranging from 1 to 96 hours. It has been found that oxidation of the conventional powder yielded a duplex oxide scale composed of an inner layer of Al2O3 and an outer layer composed of Cr2O3, NiAl2O4 and other spinels. Interestingly, oxidation of the as-sprayed nanostructured coating yielded a similar duplex oxide scale while oxidation of the polished coating resulted in a single Al2O3 layer. These findings indicated that surface oxide seeds act as nucleation sites for the growth of the mixed oxide layer. Also, it was determined that nanostructuring of the coating promotes the nucleation and growth of a single and adherent a-Al2O3 layer by increasing both the number of diffusion channels and the aluminum concentration at grain boundaries.

Jan 1, 2010

By E. V. Manlapig, M. A. Hampton, M. E. Holuszko

Methanol treatment of ZnS particles has been found to remove slimes and facilitate flotation. The removal of slimes renders the ZnS surface more hydrophobic, resulting in an increase in the hydrophobic attractive force between the particle and bubble. Hallimond tube flotation, induction time measurement and particle-bubble force analysis with the atomic force microscope (AFM) was undertaken to link the beneficial effect of methanol treatment of ZnS particles to their increased floatability.

Jan 1, 2009

By A. Pawelczyk, D. Hreniak, E. Zych, W. Strek, K. Grabas, A. Ostrowski

"Nowadays recycling became an important rare earth elements (REE) source, which allows to reduce their demand for extraction from natural deposits. At present, the used fluorescent lamps and old type TV or computer monitors kinescopes are selectively collected and undergo processing in the system of recycling. It has been estimated, that utilization of such waste would be sufficient to cover the REE demand for the next 5-8 years. In the developed process, the luminophores were separated from the electronic and electronic waste materials, and processed by hydrometallurgical methods to obtain concentrated REE in form of oxides. INTRODUCTIONInternational Union of Pure and Applied Chemistry (IUPAC) defines the rare earths as a set of seventeen chemical elements, specifically the fifteen lanthanides plus scandium and yttrium. They are considered the most important indicators of the developed technologies and techniques. Rare earths are used, amongst others, for the production of magnetic and superconducting materials, ceramics, lighting, catalytic converters, advanced electronics and alloys. The demand for RE continually increases, similarly to many other primary raw materials. Globalization, the growing demand for limited resources of raw materials, the policy of the countries controlling the raw material market and the economic crisis became a spur for new programs of socio-economic development of the European Union (EU), with particular regard to EU safety for commodities in intermediary as well as long-term horizons (COM 2008), COM 2011).EU countries import most of metallic and chemical raw materials important for their economy. In 2008 a detailed program named Raw Material Initiative was announced. The increase in demand for most raw materials having special importance for the development of technology, and access to of raw materials security of supply affect the future economies of the UE member states and other developed countries."

Jan 1, 2012

By O. D. Maurice

Feldspar mining in Canada came to an end during 1972 after many years of continuous activity. The deposits are not exhausted and the domestic demand for this product is expected to continue at about the same level as in recent years. The size of the industry does not justify the installation of expensive equipment in the mills, but it is believed that a modest profit could be made by a small operation using rudimentary methods of separation. Largescale and accurate mapping of the pegmatite dykes could help in planning mining operations for a better recovery of a uniform product.

Jan 1, 1973

"Introduction The first documentary record of coal nurung on Vancouver Island was that of the Hudson Bay Company operations in the Suquash area in 1836. Between 1836 and 1862, the Hudson Bay Company mined some 65,000 tonnes from this Suquash field and the Nanaimo coal fields discovered in 1851. However, systematic mining of coal did not take place until the Hudson Bay Company holdings were sold to the Vancouver Coal Company in 1861, and a rival company under Robert Dunsmuir was established in 1869. These two interests under various organizational names and jointly as the Canadian Collieries (D) Ltd. (1928) developed and exploited the coal seams of the Nanaimo and Comox Basins from 1852 to 1966. Because of the proximity of the coal outcrops to tidewater, the coal was readily marketed to ocean-going and coastal ships for fuel. However, during the turn of the century the main market was to meet the demand of the developing cities along the west coast of Canada and the United States for residential and commercial heating. Island-based copper smelters and brick factories, and the coming of the railroads motivated by steam engines increased the demand. This economic success of the industry continued until 1922 when a peak production of over 1,750,000 tonnes was reached. Following 1922 labour unrest in the industry, which affected the certainty of supply, and the availability of alternatives in the form of California petroleum and mainland coal combined to cause a rapid and steady decline in the demand for Island coal. In spite of post-and pre-wartime prosperities the trend could not be reversed. Serious coal mining phased out in the Nanaimo area in 1939 and in the Comox area in 1967. puring the 114 years in which the industry flourished over 75 million tonnes of coal were mined from more than 30 mines and a minimum of ten new mining communities were established on Vancouver Island."

Jan 1, 1985

By M. Bender, H. D. Goodfellow

"Belt conveyors, because of their low capital and operating costs and inherent flexibility in handling a wide variety of products, have numerous applications in the mining industry. With the increased emphasis on improving the workplace environment, dust emissions from belt conveyors at transfer and other points have become a significant problem for many applications.The paper reviews belt conveyor dust control technology and compares dust emissions from belt conveyor systems with other possible materials handling systems. Technical information on existing belt conveyor installations which have been designed to minimize or eliminate dust emissions is summarized. The important features of good design as well as the necessary input from operating and maintenance personnel are highlighted. The status of research and development work on dust control on belt conveyor systems on a world-wide basis is discussed. A proposed methodology for field measurements of emission factors from belt conveyor systems is presented. Data collected from such a test program can be used to establish a design basis for new dust-free belt conveyors.IntroductionBelt conveyors have proven themselves over the year s in the mining industry as a reliable and low-co st method of moving bulk material at high tonnage rates. Because of the above, as well as their inherent flexibility in handling a wide variety of products, belt conveyors are often called the ""workhorses"" of bulk material handling systems. For many processing plants, belt conveyors serve as the ""vital link"" in providing feed to the plant and the removal of the finished product. As would be expected, there has been considerable engineering effort in designing rugged and reliable belt conveyor systems.It is also well known that belt conveyor systems are a primary source of respirable dust emissions. The major sources are from the tail pulley where material is received and the head pulley where material is discharged, from the return idlers, due to the fine material attached to the return belt, and from the take-up pulley. It is usually considered that for dust particles less than 10 microns, these particles will remain airborne and thus can have a profound effect on the workplace environment."

Jan 1, 1982

By Akiyoshi Horiuchi, Manabu Kanno, Shigeki Sato, Taro Aichi

"AKITA ZINC Co., Ltd. (Iijima Zinc Refinery), jointly owned by DOWA METALS & MINING Co., Ltd.(DMM), has used the company’s own hematite process for iron control since the beginning of operations in 1971. The hematite process consists of reductive leaching with SO2 gas and iron removal in autoclaves by high temperature hydrolysis. This process enhances not only zinc recovery but also the recovery of gold, silver, copper, lead and rare metals, which is carried out at another DOWA metallurgical plant. All by-products produced in the hematite process are marketed and sold. This paper presents an overview of the hematite process and the recent process improvements made.INTRODUCTION DMM carries out mining and smelting activities for precious metals, PGMs, rare metals and base metals such as copper, lead and zinc. It owns KOSAKA SMELTING & REFINING, producing copper and lead, and the AKITA ZINC Co., Ltd. (AZC) in Akita Prefecture. DOWA is a specialized smelting company which has established a metallurgical complex for copper, lead and zinc, including a recycling business. AZC was established in 1971 at a production capacity of 72,000 t/y zinc; it is jointly owned by DMM and five other non-ferrous metal companies. AZC has increased its capacity continuously and now produces 210,000 t/y of zinc. Figure 1 shows the changes in zinc production and capacity at AZC."

Jan 1, 2016

By Lopatka. M. J.

This paper presents the results of 3 tons skid steer 6x6 wheel robot drive system field tests. The aim of the investigation was verification of assumed data for drivetrain diesain and forces identification in the drivetrain system during maneuvering and crossing obstacles. Robot has hydraulics drive system with motors in the wheels and hydraulic suspension system. The neded drive torque on wheels was determined by pressure measurnig on motors.

Aug 1, 2013

By Jacques Nantel

"The molybdenite property of Brynnor Mines Limited, Boss Mountain Division (wholly-owned subsidiary of Noranda Mines Limited), is situated approximately 360 miles northeast of Vancouver on the east slope of Takom-kane mountain in British Columbia's Cariboo District. Orebodies at the deposit fall into two categories; quartz breccia, and veins and stringers. The development of the breccia ore zone was started in June, 1964. The bulk of the ore is being mined from the stringer ore zone. The ore-body has been divided into 100-foot stopes and pillars. A sub-level blasthole method is used and the broken ore is handled in drawpoints and scram drifts. The development, drilling, blasting and handling of the ore are reviewed. The future pillar recovery operation is also analysed. The paper is also concerned with a scheduled shaft sinking program."

Jan 1, 1970

By Ralph Johnson, Philippe Gaultier, Loui Fauteux, Andrew Dasys

"This paper outlines the implementation of the Mechanic's Stethoscope from the earliest stages of development to the implementation at Brunswick Mining and Smelting. It details the cooperative efforts of personnel at Noranda Technology Centre (NTC) and Brunswick Mining & Smelting (BMS) during the technology transfer of the Mechanic's Stethoscope. It demonstrates how everyone worked toward a goal of developing a product that is accepted as a useful addition to the work environment.The Mechanic's Stethoscope is an underground vehicle diagnostic system consisting of computer hardware and software intended to assist mechanics in daily tasks. Its tools facilitate quick and easy access to any information required during the maintenance of an underground vehicle. Each tool presents vehicle condition data in a simplified manner. The additional information improves the mechanics understanding of the vehicle condition. The result is a healthier fleet of vehicles and faster diagnosis times.When introducing a computer based system into a traditionally non-computer oriented environment a concern is the acceptance of the system. This concern exists on many levels."

Jan 1, 1995

By David G. Dixon, Ahmad Ghahremaninezhad, Edouard Asselin

"Atmospheric leaching of chalcopyrite in sulfuric acid solutions is a slow process due to the mineral’s passivation. We have investigated the nature of the passive film in this work. Electrochemical reduction and oxidation of chalcopyrite over the potential range of -0.5 to 1.2 VSHE were investigated in 0.5 M sulfuric acid solution (pH 0.3) at 25 ºC by multicyclic voltammetry and open circuit potential measurement. The influence of scan limits on the evolution of current peaks was studied with both stationary and rotating electrodes. It was observed that the anodic oxidation of chalcopyrite begins at potentials above 0.6 VSHE, most likely by preferential dissolution of iron atoms over copper atoms. The selective electro-dissolution process results in formation of a metal-deficient sulfide passive film (i.e. Cu1- xFe1-yS2, y > x). The passive film dissolves at 0.9 VSHE. Elemental sulfur is one of the products of chalcopyrite dissolution above 1.0 VSHE. Cathodic reactions within the potential region of 0.1 to 0.6 VSHE and anodic reactions at potentials lower that 0.5 VSHE are associated with at least one soluble species from solution. The soluble species involved in the cathodic reactions are likely ferric and cupric, while the soluble species involved in the anodic reactions is likely H2Saq."

Jan 1, 2014

By Gordon MacVean

The object of this paper is to present for your consideration some of the present-day trends of safety practice in the coal mines in the United States and Canada. Coal mining at its best is a hazardous occupation. Men must be experienced miners in order to appreciate the existing hazards and must remain ever conscious of them if they are to work safely. The question is often asked whether our efforts for increased safety are showing results. So often it appears that strides are made for a period of a few years in the reduction of fatalities and lost-time accidents only to have all ground lost by an unfortunate year, after which progress is commenced again only to have a repetition of the same thing. Table No. 1 is an answer to this question. It shows the fatality rates over the last two decades in the coal mines of the United States and Canada. These are given in divisions of five years. The general trend is noticeably downward, exceptions being due to explosions or disasters which claimed an unusually heavy toll of life. These last are certainly not as common today as they have been in the past. It is only reasonable to suppose that this trend towards a lower fatality rate is the result of well directed safety effort. Reliable statistical organizations have offered figures to the effect that only 15 per cent of all accidents can be eliminated by the use of mechanical safeguards. The state of mind of the man involved, or his attitude towards safety, commonly called 'safety-consciousness,' is the controlling factor in the prevention of 85 per cent of our accidents.

Jan 1, 1931

By Alexander Burns, David Dreisinger

The kinetics of the oxidation of uranium(IV) by oxygen gas in aqueous systems is dependent on acid concentration, oxygen partial pressure, and temperature. In order to better understand the relationship between these variables and the speed of oxidation, a series of experiments have been conducted where each parameter has been varied in turn. Data were collected continuously using UVVis spectroscopy, allowing for a detailed examination of the reaction rate over the course of each experiment. The data fit an overall apparent rate law that is 1.5order in uranium(IV), -2order in H+, first order in oxygen, and unaffected by uranium(VI). This relationship does not appear to hold for solutions with <0.2 mol/L initial acid, where a different kinetic mechanism appears to be dominant.

Jan 1, 2014

By P. Tukkaraja, K. Katzenstein

"Block caving is one of the most economical and efficient underground mining methods and has gained popularity around the world especially for extracting low grade and massive ore bodies. However, during the extraction of ore from the draw bells, gases trapped inside the cave could emit into the working areas; hence, ventilation plays a key role in operating block cave mines successfully where gas emission is a concern. To design an effective ventilation system for a block caving mine, given the dynamic nature of the caving process, it is necessary to develop airflow characteristic curves (P-Q) for a given cave. This study uses a 1:100 scale physical model with an exhaust fan system, and a Computational Fluid Dynamics model of a block cave to investigate the airflow behavior through the cave filled with broken rock material. From this study, it was observed that the cave airflow resistance increases with the decrease in cave porosity and the particle size.INTRODUCTIONThe block cave mining method is gaining popularity owing to its low cost and high productivity. This study considered a case where this bulk mining method is used for the extraction of an orebody that contains uranium mineralization. During the extraction of broken ore from the draw bells, radioactive gases trapped in the cave zone could be released into the production drifts and could create unsafe working conditions in the mine. Mine ventilation systems play an important role in regulating the migration of radon in working areas. One of the strategies to control radon migration in a block cave mine is to exert negative pressure on the cave zone by using an exhaust fan above the cave zone. In order to select an appropriate exhaust fan system, it is necessary to study the airflow resistance of the cave zone (Loring & Nelson, 2006).Extraction of broken ore via drawpoints creates a void volume inside the cave called the air gap. Air gaps with larger heights can lead to air blasts in a block cave mine should the cave collapse. Besides that, the air gap can also lead to decrease in ventilation system efficiency due to recirculation of air flow and associated shock losses. Air gap height can also have a profound effect on the variation of cave airflow resistance (Erogul et al., 2015, 2017). The knowledge of cave airflow resistance is also important for predicting the intensity of an air blast. Cave airflow resistance is a function of cave properties such as broken rock size, air gap, and porosity inside the cave zone (Baysal et al., 2017). Initially, a scaled experimental model with a forcing system was developed to investigate the airflow behavior through the cave, however, this model couldn’t provide an observable change in the airflow resistance when the cave properties were changed (cave porosity, and airgap) This was attributed to the difficulties associated with forcing system in terms of achieving lower porosity values with the available material (lightweight shipping boxes) for simulating broken rock inside the cave zones, and controlling air leakage from the model (Ajitha et al., 2018)."

Jan 1, 2019

By C. C. Walden, D. W. Duncan, P. C. Trussell

Thiobacillus ferrooxidans released copper from -400-mesh chalcopyrite at a rate of 54 mg/I/hr. Any flotation chemicals remaining on the concentrate did not inhibit the leach rate. Zinc rougher tailings were also leachable. With bacteria, 75 per cent of the zinc and 68 per cent of the copper came into solution. In the sterile controls, only 16 per cent of the zinc and 10 per cent of the copper were released; 100 per cent of the copper and 36 per cent of the zinc were leached from pyrite cinders through the action of bacteria, and 17 per cent of the copper and 10 per cent of the zinc were solubilized in the sterile controls. Less than 0.027 per cent of ~he iron came into solution. The majority of the copper in a converter slag was acid-soluble, but a reverberatory slag responded to microbiological leaching. About 62 per cent of the copper came into solution, compared to 12 per cent in the sterile control. The various factors influencing the rate and extent of microbiological leaching are discussed.

Jan 1, 1966

By Lorrie Fava

Two needs in the mining industry, to enable overall process improvements, are open systems and network connectivity in underground mines. The Pando project, a collaboration between Symboticware, Vale and Xstrata Nickel, and supported by CEMI, addresses these issues, and leverages the solution platform to deliver intelligent applications. An open system is one that uses publicly available standards for its key interfaces. Vendor-neutrality and ease of information flow are two main benefits that result from the use of open systems. By facilitating the interoperability of systems, open systems allow information to be available when and where it is needed for decision support. Network connectivity in underground mines is typically limited, with hotspots in strategically chosen areas that are relatively static. Mobile equipment moving through a mining work cycle experiences intermittent connectivity; in this situation, seamless remote equipment monitoring is impossible. The Pando project establishes an open technology platform, adhering to the IREDES and OPC UA standards. It enables the collection and integration of information generated by mobile equipment? seamlessly while there is a network connection, and as a store-and-forward gateway to manage intermittent connectivity. The platform capabilities are leveraged to support embedded intelligent applications. This open platform, the SymBot, is a rugged hardware and software device. The platform complies with open standards for industrial automation and systems interoperability. The SymBot platform is capable of providing advanced real-time decision support at the device level, and is designed to be remotely configurable. Applications being developed through the Pando project include engine monitoring, a dynamic load weighing system, machine location monitoring and automated activity monitoring including production and maintenance reporting.

Oct 1, 2010

By D. F. Scott

"DEFINITION OF THE REGION AND ITS BOUNDARIESTHE REGION of Western Canada covered by this re-port lies between the Precambrian rocks of the Canadian Shield and the structurally deformed rocks of the eastern Cordillera, extending northward from the international border to the 60th parallel. It is some 487,000 square miles in area, with a total sedimentary fill of about 535,000 cubic miles0>. It includes parts of the prairie provinces of Manitoba, Saskatchewan and Alberta and the northeast corner of British Columbia and forms part of the geological region known as the Interior Platform, commonly referred to as the Western Canada Sedimentary Basin. The bedrock comprises carbonates and evaporites of Paleozoic age that lie on Precambrian crystalline rocks and are over-lain by a relatively thick blanket of Mesozoic and Tertiary elastic rocks. The nearly flat-lying bedrock, covered by a thick mantle of glacial drift, forms the Interior Plains physiographic province."

Jan 1, 1970

By W. E. Newton

THE following notes are offered primarily to show that industrial minerals or their products have a much more important place in the metallurgical industry than is perhaps generally realized, and with the hope also that some statement by the metallurgical consumer of the relative merits of various materials for particular requirements or services will l;>e of value to the industrial mineral producer. These notes are not in any way presented as complete. Also, some of the statements made may be debatable. The grouping adopted is as follows: (1) Refractories; (2) Fluxes; (3) Construction materials; and ( 4) Miscellaneous applications. Fuels are not dealt with in the present paper. REFRACTORIES GENERAL: Refractories are materials which will withstand high temperatures with-out melting or becoming markedly soft or pasty. While their primary function is to withstand heat, they are usually called upon to resist one or more of the following destructive influences: abrasion, pressure, corrosion by slags or fluxes, and rapid changes in temperature. Refractory materials may be conveniently divided into three classes: (1) Acid refractories-consisting of silica, or containing silica as their chief constituent. They combine more or less readily with metallic oxides, forming silicates, and are hence termed &apos;acid&apos;. The most important of these are quartz, quartzite, siliceous sand, tripoli, Dinas rock, and ganister. Most fire-clays, although generally considered neutral sub-stances, contain relatively small amounts of free silica and are, to that extent, acid. (2) Neutral refractories-the term is merely relative in most cases, since, at high temperature, many of the refractories that are classed as neutral will react chemically with a strong base, functioning as a weak acid; or, conversely, with a strong acid, functioning as a weak base. Chrome and graphite are the most nearly neutral of all the commonly used refractory materials.

Jan 1, 1936

By W. Keith Buck

This paper defines the discipline of mineral economics. By example, it describes the application of the tools of economic analysis to mineral problems - to problems in the areas of: mineral resource analysis and forecasting, mineral industry activity from exploration to distribution and marketing, mineral commodity analysis, and mineral policy analysis and policy formulation - all in a regional, national or international context.

Jan 1, 1972