Search Documents

Iron deposits of every major type except laterite occur in Quebec, and form one of the major iron ore resources of the world. The five principal types of ore described are: (1) hematite-goethite masses derived from iron formation through the oxidation and enrichment of iron by natural processes; (2) taconites consisting of fine-grained iron formation; (3) metataconites composed of coarse-grained iron formation; (4) iron and titanium oxide minerals in massive or disseminateed deposits within gabbro and anorthositic rocks; and (5) replacement or contact? metasomatic magnetite deposits associated with complex silicate and skarn mineral assemblages. Most of the ore, although relatively low grade, is easy to concentrate. The physical properties of the ores that affect the choice and efficiency of beneficiation methods are described. The extent to which iron ore from this area can be utilized in the future will depend on the continued use and improvement of highly efficient methods of beneficiation.

Jan 1, 1964

By John B. Phillips

The mine is entered by a central vertical shaft, strongly timbered, and containing two compartments-one for the passenger cage, the other for the large skips bringing the ore to the surface. A man-way, for emergencies, is also provided, parallel to the shaft. The cage is a single-deck steel box, carrying about thirty persons; by means of arrangements above and below, it can also hoist and lower materials needed in the workings. Levels are run at intervals of 100 feet. In special cases, where the ore conditions warrant, sub-levels are operated, such as those at 1,113 feet and 1,123 feet (Fig. 7), which are connected by winzes with the 11 th level. One of these was pushed for 40 feet, and then abandoned because it was unprofitable to take up ore of the grade encountered. The ore between levels is removed by stoping. The drifts follow the course of the veins as much as possible, with numerous cross-cuts. Winzes, raises, connections, etc., are blasted out where needed. The main drifts are at least 8 ft. high by about 9 ft. wide. All former narrow drifts had to be widened sorne time ago, by ruling of the Ontario Department of Mines, to lessen the danger of accidents with cars in the small passages. Accurate plans of the under-ground workings are kept in the office, and extensive surveying is always being done underground to keep the maps up to date, measure the cubical contents of stopes, and so forth. Timber is extensively used in the construction of supports and chutes, and in the sinking of the shaft. Steel and concrete are too expensive to compete with timber, which 1s abundant in such sections as have escaped forest tires.

Jan 1, 1926

By Charles S. Ney

"THE WRITER'S acquaintance with Kootenay King mine is limited to a brief geological excursion in the vicinity. This paper has been compiled largely from maps of J. Sullivan, mine geologist in 1952, kindly made available to the writer by Transcontinental Resources; a 1942 private report by W. L. Brown; and personal communications with J. Sullivan. Remarks on regional geology, and the comparison with Sullivan mine, are specifically the writer's.The Kootenay King mine is situated in the westernmost range of the southern Canadian Rockies at an elevation of 7,300 feet. From the Sullivan Mine at Kimberley, B. C., it lies 19 miles due east. Six miles of this distance are represented by the pronounced topographical and structural gap of the Rocky Mountain Trench. Mineral claims were locat-ed in the area prior to 1898. The deposit was first seriously explored in the late 1920s, and a small orebody was then outlined and developed. Mining and milling were undertaken in 1951.52. The orebody, amounting to about 14,000 tons, was mined out, and no significant new ore was revealed.The orebody is a replacement of dolomitic argillite by fine-grained galena, sphalerite, and pyrite. The sulphides are finely laminated in the direction of bedding, following out minor folds faithfully. The grade of ore estimated from diamond drill holes (W. L. Brown, 1942) was 11 ·I per cent zinc, 11 ·I per cent lead, and 3·8 ounces per ton of silver. The mineralized zone extends about 250 feet horizontally, 160 feet vertically, with a width of six to twenty feet.General GeologyThe country rocks are sediments of the Aldridge formation of late Precambrian age. For several thousand feet stratigraphically above and below the mine, the formation consists mainly of thinly laminated argillite and siltstone. Several horizons contain appreciable carbonate. About 2,800 feet stratigraphically below the mine, predominantly dolomitic beds mark the top of the underlying Fort Steele formation. The medium-bedded fine quartzites, which characterize about 10,000 feet of the Middle Aldridge in the Purcell range, have a restricted development amounting to only 2,000 feet in the Rocky Mountains. This member is about 2,200 feet above the mine horizon."

Jan 1, 1949

By J. H. McKibbon

This paper outlines the basic steps in the sizing of electrostatic precipitators according to the Deutsch equation. Design parameters that do not appear in the equation are also described.

Jan 1, 1971

By C. T. Morley

The steadily increasing interest in high pressure grinding rolls (HPGR) as a legitimate alternative comminution technology for hard rock applications has led to a proportional increase in the demand for trade-off studies comparing HPGR with more established approaches, typically SAG-based but including AG and stage-crushing designs. The primary trade-off is between a) the higher capital cost typically incurred with HPGR-based designs and b) the higher operating costs of the more traditional technologies. However, if, through circuit design innovation, the capital cost penalty of HPGR circuits could be eliminated or reversed, then the need for trade-off studies would diminish.

Jan 1, 2012

By T. I. Urbancic, C-I. Trifu

"ABSTRACTSeveral case studies are presented on the use of seismic techniques to map active structures, evaluate changes in stress levels, and identify the conditions leading to large magnitude seismic events and the generation of rock-bursts in Canadian mines. The results suggest that microseismicity can be used to identify the orientation of active fractures; define regions of relatively high and low stress, and those most likely to host a rockburst; determine the role of local stress on observed shear failures; and identify the path of stress transfer associated with the remote triggering of rockbursts. Additionally, the conditions leading to rock-bursts can be characterized by a significant increase in the clustering of microseismic events along the fault plane orientation of an impending event, and an increase in the effective stress levels. It is concluded that the analysis of microseismicity provides the means for remotely monitoring rock mass behaviour as a result of mining."

Jan 1, 1997

By J. R. Fisher

"Uranium may be leached to some extent in situ from the Blind River conglomerate uranium ores by using the products of bacterial activity from the bacterium Thio-bacillus ferrooxidans his paper describes some of the laboratory techniques used to investigate the characteristics of the bacteria, and to utilize their properties in uranium leaching. The application of some of the laboratory results underground at the Milliken mine of Rio Algom Mines Limited are de-scribed, along with the method of uranium recovery from the mine waters."

Jan 1, 1966

By P. Babak, E. Insalaco, O. Babak, P. Henriquel

"Detection of outliers is an important primary step in geomodelling. Geological datasets often contain errors due to problems such as measurement device limitations and recording glitches. In this paper, a robust Mahalanobis distance–based approach is successfully applied to particle size distributions of the Joslyn lease, an oil sands development site near Fort McMurray, Alberta, Canada. Automatic outlier detection and geological review were combined. Outliers from the Mahalanobis distance approach were compared with their respective core photographs to determine if laboratory measurements and facies classification were correct. A checking procedure for laboratory technicians is proposed.RÉSUMÉ La détection des valeurs aberrantes constitue une étape primaire importante de la modélisation géologique. Les ensembles de données géologiques contiennent souvent des erreurs en raison de problèmes tels que les limitations des instruments de mesure et des pépins d’enregistrement. Dans le présent article, une méthode robuste basée sur la distance de Mahalanobis a été mise en oeuvre avec succès aux granulométries du bail minier Joslyn, un site de sables bitumineux en développement à proximité de Fort McMurray, Alberta, Canada. La détection automatique des valeurs aberrantes a été combinée à une étude géologique. Les valeurs aberrantes de la méthode de la distance de Manalanobis ont été comparées avec leurs photographies respectives de carottes de forage afin de déterminer si les mesures en laboratoire et la classification des faciès étaient correctes. Une procédure de vérification pour les techniciens de laboratoire est proposée."

Jan 1, 2015

By M. M. Williams

ALBERTA has been generously endowed with oil, natural gas, coal and water power, thus giving power producers a wide choice in the type of plant and fuel which can be used. Therefore, with such a variety of energy sources to choose from, why was coal selected as the primary fuel at Calgary Power's Wabamun steam plant? This part of the paper will cover the circumstances that led the Company to decide in favour of coal. The second part, to be presented by C. F. Doerr, will describe how the Wabamun coal mine has been developed to supply the large fuel requirements of the power plant. Before considering the Wabamun plant, we require a general under-standing of? the Company's electric system and load. Power is fed into a 5,100-mile high-voltage transmission grid from eleven hydroelectric plants and from the Wabamun steam electric plant. These plants have a combined generating capacity of 820,000 horse-power. Of this total, the hydro

Jan 1, 1963

By Peter Chmara

The measurement of dust concentration in Ontario mines since 1926 has been accomplished by konimetry, based on South African experience and methods. The introduction of a voluntary program of semi-annual surveys of air conditions at all operations throughout Ontario mines created a need for an instrument that would assess konimeter spots rapidly and accurately. The development of the Electronic Scanner, it is felt, answers this need. A program whereby all konimeter spot samples taken at Ontario mines will be counted at the MAP AO field offices in North Bay is described.

Jan 1, 1969

By Kish. L.

"The results of a chemical and mineralogical study of eighteen opaque-oxide occurrences are discussed and the detailed chemical, metallurgical and mining feasibility study of a vanadium-rich magnetite deposit is summarized. A plot of the mol-percentages in the system FeO- Fe2O 3-TiO2 indicates that the deposits fall into two distinct groups: some contain hematite with ilmenite, and some others have magnetite with ilmenite (titaniferous magnetites). The plot also suggests that the two types of deposits were crystallized from liquids of different compositions. Each group has its distinct structural features. Vanadium is present in all of the studied specimens, however concentrations of economic importance have so far been found only in the titaniferous magnetite deposits. The vanadium content of the oxide concentrations of the Dore Lake Complex is the largest among the studied occurrences. Analyses of the concentrates of the drill-core sections show a compositional variation across the orebody; a continuous increase in the tenor of Ti02 and a decrease in the vanadium content upward in the layered sequence is found. Concentration tests on several tons of samples indicate that about 80 per cent of the vanadium is recovered in the magnetite concentrate."

Jan 1, 1972

By O. Babak, J. G. Manchuk

ABSTRACT A significant factor in evaluating bitumen recovery from an oil sands mine is the particle size distribution (PSD). Increased understanding of mined ore quality and improvement in predictions of recovery can be achieved through PSD modeling. This paper addresses PSD modeling using geostatistics. PSDs may be described using many discrete particle sizes, making this a challenge. The approach parameterizes PSDs with a few statistics. A lookup table is used to reconstruct the PSDs based on models of the statistics. The workflow is applied to Total E&P Canada’s Joslyn Lease and yields good results that reproduce input statistics without introducing artifacts.

Jan 1, 2013

By R. J. R. Welwood, F. J. Grebenc

"Brunswick Mining and Smelting Corporation Ltd. (controlled by Noranda Mines Limited) operates two lead-zinccopper- silver mines approximately 20 miles inland from Bathurst, N.B. The principal No. 12 orebody is mined by underground methods; the second, the No. 6 orebody (6 miles away), is recovered by open-pit mining. No. 12 underground operations ar•e in two parallel massive sulphide orebodies about 400 ft apart, dipping at 75 to 80 degrees and plunging almost vertically. The initial mining phase involved longhole open stoping from the 1550 level to the crown pillar, with main levels at 150-ft intervals and sub-levels between at 75 ft. Stope dimensions average 120 ft long, 100 ft wide and 400 ft high, with alternate rib pillars as well as sill and crown pillars. Initially, ore was transferred through scram drifts below each stope by means of 125-hp electric slushers and 72-in. folding scrapers, being delivered to gravity ore-pass collection •systems feeding a primary jaw crusher below. Later, track and trackless drawpoints were utilized below most longhole open stopes and pillars. Rib pillars were recovered by longhole methods, with large blasts into a central slot and undercut, after adjacent stopes had been filled. Waste-rock stripping from No. 6 open pit has been supplied to No. 12 stopes as backfill, by means of gravityfill raises.In 1968, the decision was made to mine the remaining ore zones by mechanized cut-and-fill methods, utilizing Load-Haul-Dump equipment. Currently, approximately 60 per cent of No. 12 mine production comes from mechanized cut-and-fill mining. As before, backfill is supplied from No. 6 open pit stripping waste rock, which has been crushed to minus 6 in. The ultimate objective is to supply virtually all production requirements by mechanized cut-and-fill techniques. The No. 6 open pit, which commenced production in 1966, covers an area of 1,500 by 1,200 ft, equivalent to 41 acres approximately. Ramp roads are graded at 8.5 per cent. Each mining bench is 36 ft high and the ultimate pit will consist of 14 benches for a final pit depth of 504 ft. Present depth is 180 ft."

Jan 1, 1971

By C. O. Aksoy, H. Kose, K. Ozfirat, T. Malli, A. Gonen, S. Gurgen

In selecting mobile mining equipment, factors including availability, useful economic life, maintenance and operating costs, and spare parts availability are considered. Given these factors, trucks and shovels with different capacities are selected. Optimizing equipment for pit and hillside quarry cases, where 8% and 10% ramps are commonly in use, were examined; the effect of other mining activities such as drilling and blasting on unit cost were considered. In principle, 20 m to 25 m high benches should be economical for downhill haulage, and 7 m to 10 m low benches economical for uphill haulage. However, practice of both mining styles favours 10 m to 15 m bench heights. Hence, the analysis here was carried out with the field experience bench height range. In the study, a truck-shovel optimization was based on the movement of 5 to 20 million cubic metres (in 2.5 million cubic metre increments) of overburden stripping at the Eynez open pit mine in the Soma region of Turkey. The outcome showed that low-capacity shovels were unfavourable due to high production expectations. High-capacity shovels were also unfavourable due to health and safety issues causing high instances of impact vibration on trucks during the loading cycle and a decrease in foreseeable unit lifetimes. The number of shovel passes required to load a truck ranged from three to six. Trucks with high-capacity bodies were deemed uneconomical due to high investment and operating costs.

Jan 1, 2005

By Graham Farquharson, Jame Marshall

"Mining towns have always been an important part of Canadian geography. Many Canadians grew up in them. The frontiers of northern Canada would be a lot closer to the United States border but for the pioneering of new mines, new towns, and new transportation routes. Names such as Labrador City, Chibougamau, Val d’Or, Rouyn-Noranda, Kirkland Lake, Timmins, Sudbury, Red Lake, Thompson, Flin Flon, Yellowknife, Whitehorse,Trail and Kimberley are some of the better known larger communities that have grown to become major commercial and government centres, but which started as the base for a mining development.Many other smaller towns never grew beyond being small communities, dependent upon the local mine and many of these are still alive, but perhaps not quite what they used to be. In this list would be Buchans, Schefferville, Chapais, Cadillac, Virginia town, Lynn Lake, Uranium City, Pine Point, and Keno Hill.Nevertheless, all these towns and dozens more like them were residential communities where people lived and raised families and were quite accustomed to being days from the major centres of Montreal, Toronto, Edmonton and Vancouver, and not just hours away as wet end to measure travelling time today."

Jan 1, 1996

By J. S. Fox

It is generally recognized that the interpretation of bedrock geochemical data in volcanic terrains can be improved by adjusting for rock-type. Various chemical attributes of volcanic rocks have been put forward in the literature as rapid indicators of rock-type, but there is some question as to which of these is the most reliable . Only one such attribute, total iron, seems to have seen systematic use in geochemical mapping in the Flin Flon region. Discriminant analysis of 500 basalts, andesites, dacites and rhyolites suggests that SiO2 is the most important rock-discriminating variable and that MgO, CaO, TiD2, AI2O3 and FeOtot, are successively poorer discriminators. Lithological normalization in the subalkaline volcanic environment should therefore be made over ranges of this variable. Trace-metal data from drill core through the sulphide orebody at Hanson Lake, Saskatchewan are used to demonstrate various approaches to lithological correction, including silica normalization, factor analysis and trend analysis. All of these extract economically important information from the core that is not apparent in the raw data logs. However, silica normalization does not seem to be subject to as many serious limitations as factor and trend analysis in this case, and therefore seems to provide the most reliable basis for the interpretation of subsurface exploration geochemical data.

Jan 1, 1978

By G. Beckstead, L. F. Sawatsky, R. Nutbrown, D. Long, G. Gould

"This paper presents a case study for optimizing water management at Gregg River Coal Mine located near Hinton, Alberta. The optimization study was derived based on a review and assessment of existing management practices and plans for future operation and final reclamation. A proactive water management strategy was developed to assist mine staff in adopting a rational, environmentally sound, and economical approach to water management. A plan was developed to provide for safe operation, self-sustaining operation, low maintenance, minimum negative environmental impacts, and anticipation of future needs for existing and future operations. A plan for final reclamation drainage was developed including establishment of effective, sustainable, and maintenance-free water management systems. The study demonstrated the importance and benefits of a proactive approach for integrated mine water management. This approach is recommended for other similar mine operations because it will improve environmental compliance and reduce costs of water management. IntroductionGregg River Resources Ltd. (GRRL) operates an open pit coal mine on the eastern slopes of the Rocky Mountains, located about 45 km south of Hinton, Alberta. GRRL opened the mine in 1982 and expects to continue operations after Year 2000. GRRL has progressively reclaimed the disturbed area and expects to complete mine-land reclamation shortly after mining in the area is complete. The existing disturbed area and reclaimed area covers approximately 9.5 km2 and will expand to about 10.5 km2 upon mine closure.Like other coal mines in the mountainous areas of Alberta and British Columbia, the GRRL coal mine is subject to highly variable temperatures and moisture conditions. Average monthly precipitation varies from a low of 12.6 mm in January to a high of 113.0 mm in August, based on the precipitation record at the mine site since 1982. Despite the relatively high rainfall during the spring and summer months, excess water problems during rainfall events are quickly replaced by water deficit conditions during periodic droughts. Surface runoff varies from near zero in the winter to a mean annual monthly maximum of 78 mm during the month of June. The mean annual surface water yield is 345 mm."

Jan 1, 1997

By J. H. Brown

"THE need for continuing education has been recognized only in fairly recent years as a major concern of the engineering profession. Formerly, it was acknowledged that engineers were required, at least informally, to follow the professional literature and to give some attention to new technical and technological developments. However, those relaxed days, when progress could be followed in a casual or incidental evening of reading, have disappeared in these days of mushrooming information. The engineer is now in the position of the man trying to control the flow from a fire hydrant with a child's pail. Our problem is that of developing an effective flow system -be it trough, hose, pipe or a bigger pail.The first step in achieving an effective means for continuing the education process is to realize that the need for the system is really an outgrowth of an increasingly sophisticated society. It is merely one more symptom of that society; others would• include the facts that new engineering graduates are more highly trained than those of several years ago, that graduate schools are now the norm and that even some fairly recent technologies are becoming outdated. There-fore, let us examine the education-al systems from which the bulk of the increasing sophistication has grown."

Jan 1, 1966

By T. C. Holmes

Introduction The Dome mine, in the Porcupine mining camp of northern Ontario, is one of the important gold mines of the country, having produced over 139 million dollars worth of gold from the commencement of production in '1910 to the end of 1944. The geology of the mine is complex and a number of types of ore are known, each occurring under particular conditions. The mine workings are very extensive and by far the greater part of them have been geologically mapped only in reconnaissance fashion. By 1940, when the writer joined the mine staff, the orebodies in the sedimentary trough and the 'nose' orebodies, the first types to be developed, were almost worked out and many workings were inaccessible, so the descriptions of these types are based largely on study of the plans and records. The same applies to a lesser extent to some other types. At various places in this paper, statements are made as to the mineralogical or chemical composition of the rocks. Most of these determinations are based on examinations made with a hand lens and cannot, therefore, be regarded as very reliable. General Geology As there are several types of ore in the mine, occurring under quite diverse conditions, a brief outline of the geology is given here, sufficient to provide a general picture into which the fuller descriptions given with each type of ore can be fitted.

Jan 1, 1947

By H. Thomasson

THE war, like all destructive agencies, has focused attention on salvage and conservation, and to such an extent that a decade of normal progress has been crowded into a few months. This is particularly true as regards the repair of cutting tools. As a consequence, there has arisen a wide demand for comparable data by those engaged in such work, and for basic information by others who wish to repair tools. These repairs may be grouped in three classes: (1) The repair of broken tools of relatively slender cross-section, such as broaches, reamers, drills, etc., of a type that could be returned to service if a means to join the broken surfaces were available, as fortunately it is in the low-temperature silver solder process; (2) the repair of tools that possess shanks, tangs, and other non-cutting portions that may be broken or damaged to the extent that only the addition of metal will permit their return to service; and (3) the repair of special rotating tools, such as end-mills and milling cutters, that may have portions broken from the cutting edges or have their edges so worn in service as to require building up.

Jan 1, 1943