Search Documents

Blasting is a common practice in mining whereby solid rock is fractured, using explosives, to a more manageable size. The effectiveness of blasting influences a number of downstream activities such as shovel digability, crusher throughput and mill throughput. As the cost of explosives is relatively low compared to milling costs (mainly due to power consumption), blasting practices can be optimised so that the downstream processes are made more efficient, and an overall cost saving made. This is the basis of the Mine to Mill approach. The effectiveness of the blasting is influenced by two main factors, the blasting practices used (eg explosive amount and type) and the geology of the area. As the geology cannot be altered, the blasting practices must be refined to create optimum blasting. Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston operation, located in the heart of the Kalgoorlie Goldfields is the largest gold mine in Australia. Mine to Mill at KCGM has had varied success, with initial positive indications being lessened by a number of factors, including the increase in the amount of voids.

Jan 1, 2003

This paper deals briefly with productivity-enhancing advances in shaft sinking technology in South Africa post-World War II in general and the developments and application of long rounds since the 1980s in particular and is amply illustrated.It touches on the conversion to circular section, concrete lined shafts, the introduction of tungsten carbide drill bit inserts and grab lashing; expounds the rationale driving the development of longer rounds; and then describes the evolution of long rounds using hand-held and mechanically mounted rockdrills in South Africa and Canada by both local and foreign contractors. The recent experience gained on the sinking of the South Deep Main Shaft follows. Results obtained from this experiment are tabulated and commented upon. The paper concludes with the postulation of æwhat nextÆ and æwhere toÆ scenarios. Addenda include a list of shaft rounds in excess of three metres in length blasted in the Main Shaft at South Deep and their results, typical round design, manufacturerÆs specifications for the 6 m shaft jumbo and rock drills.

Jan 1, 2002

Western Mining Corporation, managing partner of the Windarra Nickel Project are in- stalling a raise-bored haulage shaft and under- ground crushing system at the Mt. Windarra Nickel Mine. The system will be the second of its type installed by W.M.C., the first being in- stalled at the Otter-Juan mine in Kambalda in 1976/77. Both haulage systems became necessary as a result of the increasing production limi- tations, and escalating costs of a deep decline mine. The Windarra haulage system required a single 3m diameter vertical raise drill hole to a depth of 470 metres. Two five tonne skips in balance will hoist crushed ore and mullock to the surface, at a design rate of 200 tonnes per hour, effectively reducing truck haulage leads by up to 50%. It is expected the project will be in full operation by mid 1982 and will enable the mine to achieve an annual production rate of 600,000 t.p.a. by 1983.

Jan 1, 1982

With the sinking of the new No. 3 Shaft and the increasing depth and northward movement of the mining operations, improved ventilation of the mine workings became necessary and it was decided to sink a new upcast ventilation shaft midway between No. 2 Shaft and No. 3 Shaft.The shaft is finished to 16 ft. internal diameter and connects with the mine workings at the 2,600-ft. level. It is lined with unreinforced Concrete approximately 12 in. thick. The shaft sinking routine was drilling, blasting and mucking by hand using a 27-cub. ft. capacity bucket. The concrete lining was poured in conjunction with the sinking and was normally finished within 30 to 50 ft. of the shaft bottom.

Jan 1, 1957

The application of methods using large diameter down holes has become an important facet in both the development and stoping operations of mines within the Aberfoyle group. Holes of up to 98 metres (vertical) and 78 metres (inclined) have been successfully used in stoping operations. A number of rises have been developed to meet ventilation, servicing and escape-way requirements. The most ambitious rise to date has been a..vertical 93 metre long by 4.50 metre square ventilation rise. Although some early problems were experienced, the ultimate successful completion of this rise has enabled the technique to be incorporated with confidence in future mining plans. This paper summarises experience in long hole rising techniques, their evolution from the original cratering concepts, and the approach to further development of these techniques.

Jan 1, 1982

By M Littlefair, D Gribble, R Rounsley, I Te

Low-density explosives (LDE) have applications where the explosive properties of ANFO are not well matched to the rock. In particular, rocks that are of low strength and/or well fragmented in situ. Dyno Nobel Asia Pacific (DNAP) has developed a new LDE, BlastLiteTM, which can be used as a cost-effective replacement for ANFO with excellent detonation characteristics. The product is based on ANFO with the addition of a bulking agent. The key to the product lies in the ability of the bulking agent to form a homogeneous blend with ANFO without the need for any emulsion matrix to bind the product together. This results in an LDE of low cost and high weight strength compared to existing commercial LDE products. The product has been trialled extensively and has proven to provide results that are equivalent to, and often better than, ANFO with reduced powder factors. This paper details the laboratory development and results of field trials for DNAPÆs LDE solution: BlastLite.

Jan 1, 2004

By J Bower

The JORC Code does not specify a definition for ælevel of confidenceÆ. The common approach in the mining industry is to use a certain drill spacing or number of data samples to classify resources by the confidence categories. Another approach includes application of the quantitative geostatistical criteria for non-subjective and consistent definition of the resource categories. This approach, which has become increasingly popular in the mining industry, provides a quantitative measure of the resource estimation uncertainty. In this study, uncertainties associated with the different drilling grids at the Weipa bauxite deposit (Queensland, Australia) have been modelled using conditional simulation methodology. Criteria used at Weipa for defining resource categories are as follows: mineralisation can be classified as a Measured Resource if tonnage and grade of its volume representing three months of production can be estimated with a precision error not exceeding ¦10 per cent (at 95 per cent probability, ie two standard deviations); and mineralisation can be classified as an Indicated Resource if grade and tonnage of its volume representing annual production can be estimated with a precision error not exceeding ¦10 per cent (at 95 per cent probability). Several different grids have been created by subsampling the drill hole database. The studied variables include Al2O3, SiO2, thickness of the bauxite seam and location of the footwall contact. The variables have been modelled by sequential Gaussian simulation. Based on this study the following drill spacings have been recommended: Measured Resources û 150 m by 150 m, Indicated Resources û 300 m by 300 m.

Jan 1, 2009

By Thompson IR, Solomons SS

Underground mining with the cut and fill method has been declining during the past decade or so, being replaced mostly by sublevel open stoping methods. During 1983 the Australian Mineral Industries Research Association Ltd. (AMIRA) commissioned a review of the method, with the aim of compiling the state-of-the-art, indicating future trends and recommending topics for research that would be needed to support this future mining. Mines using the cut and fill method in Australia and three other countries were visited to compile current practices and expected developments.Cut and fill is mostly used where geological and ground conditions are unsuitable for open or caving methods. These range from narrow, irregular orebodies to wide, massive orebodies where pillars are retained in ore. There is significant potential for improvement and further development of the method. It may then be used in a broader range of conditions and for orebodies that may not otherwise be viable to mine.

Jan 1, 1985

By James S. E

Financial risk of environmental problems is the key to many important business decisions within the mining industry. Massive uncertainty makes it difficult to choose a strategy for managing environmental problems to reduce corporate financial exposure to environmental impairment. A correct and practical method exists to clarify the risks and help make decisions. A case study on an insurance problem illustrates the method.The approach used is to translate existing data on environmental problems into probabilistic expressions of financial risk, and organise the expressions to reveal alternative solution strategies for the insurance problem.

Jan 1, 1993

The Woodcutters deposit, 65 km south- southeast of Darwin, N.T., consists of a series of veins of pyrite, sphalerite, and galena with some silver, cadmium, antimony, and arsenic minerals. The veins are hosted by the Early Proterozoic Whites Formation, a sequence of black slates with interbedded carbonate rocks and minor ash tuffs. The known orebodies occur about 300 to 500 metres above the contact of Whites Formation with the underlying Coomalie Dolomite, which consists of dolomite and magne- site. The stratigraphic setting is lithologic- ally similar to that of the Mt. Isa deposit, Queensland. The orebodies are replacement veins occ- urring along fault and dyke structures which are sub-parallel to the axes of a double-nosed faulted anticline. The orebodies are in part associated with two unusual carbonatized lam- prophyric dykes. The dykes were intruded after the fold and its slaty cleavage were formed. The ore has replaced the dykes and host rocks and is therefore late-stage hydrothermal miner- alization. The known orebodies are open at depth. A "bonanza" of high-grade ore occurs at the upper part of the largest orebody and is currently the subject of an open cut mine planning study by a consortium of companies headed by Nicron Resources Ltd.

Jan 1, 1984

By Carthew J

For more than 30 years shearer loaders have been the most important winning machines for,longwall mining. While the machines of the first generation had a driving power of only 100 or so kW, the present day shearer loaders may be powered by more than 1000 kW. Daily outputs of 24000 tonnes have now been reached, but this still does not set a limit. If the deposit conditions allow, further increases are possible. This requires the optimum coordination of all system components. For this paper the use of coal plows has been of little import as plows have found no favour, and nor are they likely to do so in today's economics in Australian coal mining.

Jan 1, 1988

The Iron Prince orebody occurs within the Lower Middleback Jaspilite Horizon of the Middleback Group and consists of hematite within host rocks of jaspilites and schists. The ore was probably the product of leaching of silica from jaspilites and replacement by iron, concentrations occurring in suitable structural traps. The narrowness and the presence of extensive dolerite amphibolite dykes within the orebody make it essential to operate a grade control programme in advance of the faces. Information from drilling is drawn up on bench plans, step plans and impurity overlays, and these serve both in day to day production planning and in long term planning. Mining is done selectively by open-pit methods and blending conducted by keeping at least three faces of different grades of ore open at any one time. No stock piles of ore are kept for blending, but contact ore, contaminated ore and enriched material are dumped for later beneficiation.

Jan 1, 1971

By Hunter GW

This paper gives an account of the filling system at Mount Isa from surface fill production to stope discharge underground. A brief explanation of the surface facility and reticulation is given prior to the discussion on aspects of underground reticulation. These include fill hole types, pipe and breastplate installation, wear characteristics, etc. The different types of fill and their respective applications is mentioned as a prelude to a general overview of the mining considerations associated with fill placement and its role in the long term planning strategy at Isa Mine. Some practical aspects of stope preparation and filling procedures are outlined for the various stoping methods. Finally a brief outline of future fill developments is given.

Jan 1, 1982

Deposits of chromite are in associated with ophiolite complexes in Papua New Guinea. No deposits which are currently exploitable have been recognised, but large resources that may be economic in the future are present at Ramu area and on the Morobe coast. These are contained either in laterites or in sediments derived from ultramafic members of the ophiolites. There are possibilities of establishing further resources either in similar settings or associated with ultramafic members of alkali intrusive Complexes.

Jan 1, 1987

By Ahmed M, Leung L

A program of microseismic noise monitor ing for gas outbursts, in conjunction with other mining engineering measurements and observations, is being undertaken at Leichhardt colliery in Queensland. Headings are developed at present by shotfiring. The equipment being used in this study includes piezoelectric accelerometer assemblies to detect microseismic noise which is then transmitted to a surface base station by cable. Data are recorded on an analogue magnetic tape recorder and are also analysed on-line using a commercially-available acoustic emission pulse analyser. It is proposed to re-interpret recorded data using various modes of analysis and to interface a desktop computer to the existing system to permit continuous monitoring on the mine site. No outbursts have been recorded or analysed and only a limited number of develop- ment shots, and the resultant microseismic activity, have been recorded to date.

Jan 1, 1980

Copper grades of diamond drill hole and development samples are determined in the core shed logging area at Mount Isa Mine using a Bulk Mineral Analyser. All geological and grade data on the copper orebodies is collected and stored on computer file.The raw data can be manipulated interactively using a computer terminal or by input of forms to produce output as computer plots or printouts. Grade distribution of copper or cobalt is obtained by the geologist using a computer kriging package followed by grade contouring. Computer plotted cross-sections and plans of individual stopes or several stopes can be produced showing geological structures, kriged grades at points and as grade contours.

Jan 1, 1985

By Zeni J. T

Gold was mined from quartz bodies at Ballarat East from the 1850s until closure of the last mine in 1917. The average depth of mines was about 350 m.Ballarat Goldfields Limited (BGL) carried out diamond drilling from surface between 1985 and 1987 which proved the continuation of gold-quartz mineralisation beneath the old mines.During 1989 an underground development program was commenced to access the mineralisation for detailed exploration. The program included two simultaneous shaft developments. These were known as B2 shaft and Llanberris No.1 shaft.

Jan 1, 1992

In a country richly endowed in mineral wealth, Climax Arintco Mining Corporation's ICAMC) Dinkidi porphyry Au-Cu deposit in Nueva Vizcaya, Philippines, represents the most significant mineral discovery in this country in recent times. The deposit is located within a belt of young intrusive and volcanic rocks in the Sierra Madre mountain chain of north Luzon, a region previously unassociated with porphyry -style mineralisation.Since 1989, drilling of the Dinkidi deposit has outlined a resource of 124 million tonnes of 1.0 g/t gold and 0.4 per cent copper. Regional exploration throughout CAMC's 37 000 hectare FTAA has identified a further 16 potential porphyry-related deposits.

Jan 1, 1997

By Woodcock J. T, Sparrow G. J

Activated carbon particles obtained from a number of Australian CIP operations were examined with an optical and a scanning electron micro- scope and an electron microprobe. External surfaces, and polished sec- tions through individual particles, were examined with special reference to materials on the surface and to calcium and gold distributions. Photographs are presented of surface contamination of the particles by salts precipitated from the pulp such as calcium carbonate (calcite), calcium sulphate (gypsum), and a magnesium salt; ore minerals such as quartz, hematite, pyrite, arsenopyrite, pentlandite, and various alumino- silicates; and other substances such as grinding media and a fungus. Calcite was very abundant but the other materials were less common. Contamination in the interior of carbon particles was almost exclu- sively calcium carbonate, and extensive contamination extended to the centre of some particles. A possible mechanism for the formation of cal- cium carbonate inside the carbon particles is noted. Gold X-ray dot maps of sections through carbon particles indicated that gold was distributed throughout coconut shell carbons and that although gold was more concentrated near the outer surfaces of extruded peat carbon particles, it was also present to depths of at least 500 ¦m. The gold distribution throughout the carbon particles was similar to that rf alrit~

Jan 1, 1988

By Rosengren KJ

Geotechnical conditions often have a critical influence on the design of new open pit and underground mines, but they are often considered of secondary importance in relation to other factors, such as detailed geology, orebody geometry and grade distribution. As a result, geotechnical studies may not be carried out during early project investigations or, at best, may be given only superficial attention, often to the overall detriment of the project. Technically and economically, it is logical that geotechnical studies should be integrated with geological investigations as soon as it becomes evident that the particular deposit may prove to be economic. The paper discusses the use of geotechnical information in the selection of mining methods and mine design for underground mines and for wall design and assessment of excavation characteristics in open pit mines. It then considers methods of obtaining the relevant data, with particular reference to exploration boreholes. Selected case studies on the application of geotechnical data to mine design are Included.

Jan 1, 1986