Search Documents

Stripping of Fe (III) from D2EHPA Using Different Reagents The common way to extract Fe(III) from an organic solvent is by using concentrated acidic solutions. The stripping of Fe(III) from organic solvent Di-2-ethylhexyl phosphoric acid (D2EHPA) by hydrochloric acid (HCl) solutions has been found to increase with increasing the acid concentration. However, the use of a concentrated acidic solution such as 6 M HCl can degrade the organic molecules. In this research, to increase the efficiency of Fe(III) stripping from D2EHPA, effect of some acids, salts and buffer solutions was studied. Influence of Tri-butyl phosphate (TBP) as modifier on the Fe(III) stripping operation was also investigated. According to the results, the best Fe stripping recovery was achieved in the presence of low acid concentration and the salts which was 72.4 per cent oxalic acid, 70 per cent ammonium oxalate and 75 per cent buffer of oxalic acid and ammonium oxalate. The results also showed a better recovery in the presence of the buffer rather than the salt. Finally, increasing the concentration of TBP, HCl and H2SO4 resulted in a higher stripping efficiency of Fe(III). However, in the presence of oxalic acid and its salts increasing the reagent concentration did not increase the stripping efficiency and at this condition, the recovery of iron remained constant.

Sep 13, 2010

In most mines using presplitting the final excavated wall shows a zone of damage just below the crest and well defined presplit half barrels. The crest damage (surface dilation) zone varies and is added to by subsequent adjacent perimeter blasting operations. Keeping the preconditioning to a minimum is possible using the methods described in this paper, developed on several diverse and geographically distant mining operations to control crest dilation and preconditioning by presplitting in advance - not just laterally but vertically in advance. The first documented case (Delbridge, Marton and McSweeney, 2004) in the development of the concept was undertaken at AngloGold Australia Pty Ltd's Sunrise Dam Gold Mine (SDGM), located beside Lake Carey, some 730 km northeast of Perth, Western Australia. The mine had been developed in a series of cutbacks to a depth of over 300 m and began underground mining during the latter stages of open cut operations. This mine is fairly unique in that it utilised a single pass vertical presplit which initially extended over three bench heights and after the failure mechanisms were understood, over four benches. The presplit drilling for the three stacked benches started on the floor of the second bench so that any dilation was confined to the surface one bench above the crest and modified perimeter blasting was then developed to curtail damage from blasting adjacent to the new crest. The second case is based on a South African coal mine in the Witbank Coal Measures, 140 km northeast of Johannesburg, Republic of South Africa (RSA). It was important that blasting for optimal wall stability and minimal scaling was developed in advance. A dragline is scheduled to excavate the #2 seam midburden which is the lowest of the economically viable coal seams in the five seam Witbank Coal Measures. Mining of the overburden, coal and partings above the dragline midburden pass are by excavator and truck and each mining layer is individually blasted. The results of presplitting the midburden through the overlying coal seams and partings have provided a presplit with no surface dilation of the midburden crest and ensures any subsequent crest loss is solely due to blasting adjacent to the vertical presplit. Typical of all coal mines in South Africa only vertical presplits are used. Wall control is most commonly delivered by presplit blasting and one common sight after the dust clears is a ridge of broken blocks along the presplit row, usually with a main crack running between the presplit blastholes and often parallel cracks either side of the perimeter line. The surface rock strata or block structures have been dilated by the venting gases and shock waves. Decoupled, fully coupled, single or double deck charges are used depending on a variety of factors, anecdotal practices and perceived benefits. Preconditioning of the crest rock by blasting from above may not be visible to the naked eye (or non-existent in overburden in strip coal mines) but the high speed venting of explosives gases (and often the water in the presplits) preferentially follow existing cracks and structures because there is no developed presplit crack near the surface. This nearly always lifts, shifts and separates the surface structures and geological layers. Stopping the dilation by 'sacrificial' or 'in advance' presplitting has been shown to reduce the crest loss at both metal and coal mines. Drilling and presplit blasting through an upper level of bench or layer provides a degree of restraint to the target layer where the crest must be maintained and any damage caused by the venting gases will not cause concern as it is removed as planned, leaving a stable crest.

May 1, 2010

By Keet B. A, Waid J. S

The Gippsland Basin is one of Australia's most important producers of petroleum products. An inevitable byproduct of the production, refinement and transport of the millions of barrels of oil is thousands of tonnes of waste. These wastes are generated from the wellhead through to the petrol bowser and range from oily brines and coal tars to oil and petrol contaminated soils. The vast majority of these wastes are of a relatively low toxicity and most importantly are carbon-based and biodegradable. Current disposal practices tend to ignore the latter characteristic and inappropriate and/or expensive waste disposal solutions such as landfilling (tipping), incineration or ocean outfalls are the result. A very cost effective and environmentally friendly alternative is land treatment of such wastes. Landfarming, as it is called, has been successfully practiced in Europe for over a decade. Essential features of the system are: ò Application of a predetermined quantity of biodegradable waste in liquid, sludge or highly contaminated soil form, to pre-ploughed soil with concurrent addition of nutrients (N, P and trace elements) and lime to encourage bacterial activity. ò Harmless bacteria already present within the soil break down the carbon-based compounds into carbon dioxide, water and waste heat, WHILE concurrently generating new cells. The breakdown occurs over a period of weeks to months and continues with time with the extremely low levels of the more difficult waste types being the last to disappear. ò Further waste is applied to the soil at regular intervals. The treatment area may be dedicated to landfarming or may be used alternatively for agricultural purposes. Application rates vary but may be as high as 800 tonnes per hectare per year for wastes such as refinery sludges.

Jan 1, 1992

Owing to the increased consumption of sulphuric acid; Australian manufacturers have, from time to time, been seeking for a satisfactory source of sulphur that would make them independent of foreign supplies.Some years ago a considerable amount of acid was obtained from the roasting of Spanish pyrites. This ore, in 1913 or thereabouts, cost 16s. per ton f.o.b. Huelva, and freight to the eastern seaboard of Australia was about 20s. per ton. As the ore contained 48% to 50% of available sulphur, it was costing roughly 9d. or 10d. per unit, and, in addition, the cinder, after roasting, was a product of considerable value to smelters, containing as it did a high percentage of iron suitable for fluxing, and appreciable values in silver and gold.

Jan 1, 1925

Hot briquetting is a reliable, fully developed industrial concept for the passivation of direct reduced iron produced with the various processes of direct reduction. During hot briquetting, the large specific surface area of direct reduced iron is drastically reduced, and therefore the well-known problems caused by reoxidation and overheating are avoided. Even the shipping instructions published by the International Maritime Organisation (IMO) confirm that Hot Briquetted Iron (HBI) can be handled and shipped without special precautions. From the mid-1970s until today, after extensive pilot testing of the technology, a number of industrial plants for the hot briquetting of direct reduced iron have gone into operation. Additional hot briquetting plants for already established but also for new direct reduction processes are tinder construction or in different stages of planning. This paper describes the characteristics of HBI and its current industrial application for various Direct Reduction Processes.

Jan 1, 1999

By Beardsmore G. R

Geothermal gradients in the Gippsland Basin commonly exceed 35¦ C/km. Consequently models of thermal maturation may indicate exploration targets with an anomalous age/depth distribution. However regional geothermal models are constrained primarily by observations of surface heat flow. High geothermal gradients may simply reflect the presence of low conductivity coal beds within the basin. Heat flow data are not readily available for the Gippsland Basin. Normally special purpose drill holes are required to provide direct determinations of surface heat flow. These provide core samples for thermal conductivity and allow measurements of a stable geothermal gradient at least one year after drilling. Different indirect procedures are now required to provide estimates for the Gippsland Basin. Bottom hole temperatures can be used with suitable corrections to provide an indication of the regional geothermal gradient. However the corresponding thermal conductivities are more difficult to determine. Geophysical logs can be used to detect the major lithologies but detailed statistical analysis is required for numerical estimates. Complex mixing models are now suggested for geothermal surveys linking physical properties to variations in the mineralogy of each well. Allowing for low conductivity coal measures the data in the Gippsland Basin suggest values for heat flow consistent with regional trends in Australia. Interpretation is complicated by overprinting of transient thermal events with different time scales. Apart from the tectonics of basin evolution geothermal signatures may be complicated by regional ground water migration, the 'hot spot' trace associated with southward younging of Cainozoic volcanism, diagenesis, and basin refraction.

Jan 1, 1992

By M Blanch

Gas management practices across the Australian underground coal industry have evolved significantly since the early nineties with the introduction of hazard management plans, directional drilling techniques, surface gas predrainage methods, and the widespread use of ventilation and gas reservoir simulation software.The improvements are evidenced by a substantial reduction in the occurrence of outbursts and gas related delays during a period where coal production rates have increased three to four fold. The development of effective gas predrainage strategies have been afforded by the use of reservoir simulators and a significant increase in the availability of measured gas reservoir data, in particular gas content and composition, adsorption isotherms and permeability. That said significant opportunities remain to optimise gas drainage designs and increase certainty in the gas predrainage design process through an enhanced understanding of coal seam permeability and how it is applied in the gas drainage design process.This paper describes the discrepancies between measured and actual seam permeability found during the recent assessment of two pilot predrainage programs executed in the coal measures of Queensland’s Bowen Basin. The results of those programs illustrate the need to better understand the validity of measured permeability data. The history match method employed in the pilot well assessments is proposed as an integral step in the routine gas drainage design processes that will ultimately lead to increased certainty and flexibility in gas predrainage practices.CITATION:Blanch, M, 2017. Coal seam gas predrainage optimisation through an enhanced knowledge of coal seam permeability, in Proceedings Australian Mine Vent Conference 2017, pp 73–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

A President, soon after he is appointed, sees looming ahead of him the Presidential Address; and in something approaching despair wonders what he can possibly talk about which might hold the interest of his audience. After various casts about, it occurred to me that perhaps prospecting, and more particularly prospecting in Australia, might provide a subject. This is because, 'in the first place, 'prospecting is passing from the stage of chance surface discovery to that of systematic search applying scientific methods to theproblems involved, and in the second, it is the section of the industry with which I have been concerned through much of my: working life. As it makes an address of this sort more interesting if it includes specific reference to actual experience, I hope you will bear with me in such references to actual prospecting as I may use to illustrate the argument. Prospecting has always carried the glamour of sudden wealth. The picture of the prospector engaged, perhaps for years, in fruitless search suddenly coming on riches beyondhis hopes is, deeply etched in the Australian imagination. In few other places has the fervour of prospecting run higher than it did in Victoria in the generation beginning little more than a century ago following the discovery of gold.People arrived from overseas in great numbers. Most of them proceeded to: the goldfields. They moved in thousands from new find to new find. In 'so doing' they determined much of the course of the State's development. The experience of prospectors led them to formulate all sorts of theories little impeded by awkward facts, to account for the apparently unpredictable occurrence of gold.The ideas which men followed, occasionally to success, and which they were prepared to back with all they had were strange and, various, many stories are told of them.

Jan 1, 1959

By J R. Manuel, J M. F Clout

The importance of goethite to Australian iron ore production is steadily increasing as the proportion of goethite-rich, martite-goethite bedded and channel iron deposits increases at the expense of declining production from high-grade microplaty hematite deposits. For this reason, an improved understanding of goethite in iron deposits, its genesis, goethite types and their physical and metallurgical properties is vital to maintaining optimum sintering and blast furnace performance in Asian steel mills.The terminology used to describe goethite in Australian iron deposits is currently highly variable. The discredited mineral name ‘limonite’ is still in widespread use as a field term for goethite and there are many misconceptions concerning goethite chemical grade and downstream physical and metallurgical properties. The goethite classification proposed here is based on geological and physical properties from which three types are recognised including brown goethite, dark brown-black vitreous goethite and highly microporous, friable yellow ochreous goethite.In practice, typical vitreous goethite with highly reflective surfaces and conchoidal fracturing, characteristic of the hard cap zone appears from X-ray fluorescence (XRF) and electron microprobe analysis to be significantly higher in Si (up to 18.7 wt per cent), Al (up to 3.5 wt per cent) and S (up to 0.14 wt per cent) compared to the generally very low (<1 wt per cent for Si and Al) levels of these elements in ochreous goethite and brown goethite. The data dispels the common misconception that friable earthy or yellow ochreous goethite is high in Al and Si and other chemical impurities. However, P was found to be consistently higher (mean of 0.112 wt per cent and up to 0.296 wt per cent) in ochreous goethite than brown goethite (mean of 0.011 wt per cent) or vitreous goethite (mean of 0.031 wt per cent). The highly porous microstructure of ochreous goethite is thought to have a much higher surface area, which may aid in preferential adsorption of P onto the ochreous goethite mineral surface.CITATION:Manuel, J R and Clout, J M F, 2017. Goethite classification, distribution and properties with reference to Australian iron deposits, in Proceedings Iron Ore 2017, pp 567–574 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Kelsall D. F, Trahar W. J

The size by size batch flotation behaviour of copper activated sphalerite from synthetic mixtures with quartz was determined. In terms of recovery of sphalerite, the size fractions could be grouped into coarse, intermediate, and fine ranges. The behaviour of the coarse and fine ranges was significantly poorer than that of the intermediate range in both the extent and rate of flotation.Each size fraction had a fast and a slow floating component.The main effect of changing the copper sulphate addition was to alter the proportion of any size fraction which was fast floating. No correlation could be found, between the amount of copper on the spha:lerite andeither the flotation rate of the mineral or the amount of copper added to the system. It was found that fine particles did not appear to consume greatly disproportionate amounts of copper sulphate during conditioning. A modified conditioning procedure was found to lead to a higher rate of flotation and recovery of coarse sphalerite and to make poss1ble substantial savings of copper sulphate.

Jan 1, 1975

By A H. Clemens, P Lindsay

Acid producing potential static tests have been undertaken on sample lithologies from New Zealand coal mines, to rank the lithogies into acid producing waste rock and stable non-acid producing waste rock. Results indicated that the main acid producing waste rock in the Waikato coal region are the marine Whaingaroa siltstone and the Glen Massey formations and the main alkaline producing lithologies were the Tauranga group volcanic-derived sediments (A & D) and the Mesozoic basement. Coal ash analysis of 28 samples from 28 mines have also been analysed for reactive S percentage and their base potential has been quantified by the chemical index of alteration (CIA). The results provide mine management in the Waikato Coal region with a classification of problematic and stable waste rock types. XRF and CIA values determined from wash drill cuttings would provide a method of determining waste rock volumes and magnitude of palaeo-weathering underground.

Jan 1, 1999

The past decade has seen revolutionary advances in communications and information-handling techniques which have been stimulated by "cold war" military requirements and by current programmes for probing into outer space. The tools used in exploration for petroleum and minerals have been improved significantly as a result of this new space age technology and even greater improvements are on the way.Two areas of technical activity have been particularly fruitful in enhancing the effectiveness of exploration methods. These are1. the development of new approaches, based on information theory,for extracting signal from noise more efficiently than before, and2. the use of high-speed digital computers for storing and processing all kinds of exploration information, not only geophysical but geological as well.In seismic prospecting, use of information theory has led to new techniques such as time-domain filtering, wave-number filtering and correlation methods which have made it possible to obtain usable reflection data from areas which were previously considered non reflective. Complex playback and other data processing facilities have been developed to apply these approaches.Digitization of geophysical data for handling by high-speed electronic computers facilitates many of these techniques for signal-to-noise improvement. Direct digital recording of seismic data in the field is now being d'one on an experimental basis in the United States, and this should become a standard procedure, at least for problem areas.The increased dynamic range, flexibility of filtering and other data processing, and convenience of information storage and retrieval make digital recording attractive in spite of its high cost compared to conventional analogue methods. Digital computers are being programmed to carry out many operations in data reduction and interpretation with substantial savings in time and cost over conventional procedures.INTROPUCTIONIn the years that have passed since the end of the Second World War, the western world has witnessed a technological revolution which may be as far reaching in its ultimate impqct as the Industrial Revolution of the last century.

Jan 1, 1963

The small scale alluvial gold mining industry in Papua New Guinea (PNG) is c.irrently the only form of small scale mining carried out in this country. It already contributes significantly to the economy with current production estimated at 2 000-2 500kg per year. Until recently, small scale alluvial gold mining has been confined to simple panning and sluicing of high grade alluvial and colluvial deposits. Traditionally the small scale miner in PNG has only worked gravels with gold grades in excess of 500mg/m3. Grades of this order are required to justify the hard physical labour involved ~n hand operated small scale mining methods. .he introduction of higher throughput technologies such as trommels fed by hydraulic excavators has the effect of altering what constitutes an economically viable deposit. Mechanised techniques allow for the consideration of grades of almost half that level. The potential and opportunities for utilising this type of small scale mechanised mining in PNG are enormous with large areas of ground with gold grades running in excess of 250mg/m3 and often up to 2000mg/m3 throughout the country. An assessment of the current operating economics of this technology in the PNG context is the principal objective of this paper. Small to medium scale mechanised mining can potentially contribute significantly to the PNG economy particularly as it lies within the react-, of many PNG businessmen. Its potential is currently somewhat limited by a general lack of infrastructure and is also constrained by socio-political factors.

Jan 1, 1991

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330 lb/sq. in. tension to 3,750 lb/sq. in. compression. Photoelastic examination of loaded plastic and actual rock model mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a borehole extensometer and a series of anchors at various horizons to 30 feet in a vertical roof borehole showed that when a standing face was advanced the roof movement was practically confined to the lower two feet. The majority of this movement occurred during the 36 hours after mining at this face commenced.The use of a radioactive isotope and a scintillation counter in a pair of parallel boreholes is a sensitive and accurate method of roof bedding plane crack detection.INTRODUCTIONA knowledge of strata stresses is required to understand the deformation of an underground opening and, in particular, the roof behaviour. It is the aim of investigations currently being conducted by Australian Coal Association (Research) Ltd. to determine the stress existing around mine openings and the location and magnitude of roof movement.STRATA PRESSURE MEASUREMENTMost measurements of strata stress are performed at the surface of underground openings and the majority measure the change of strain resulting from stress relief. The accuracy of the measured value of stress depends upon knowledge of the rock modulus of elasticity. The flat jack method has the advantage that strain relief is restored by a measured stress applied directly by the jack. The rock modulus of elasticity can also be determined.

Jan 1, 1963

Using a cylindrical hydrocyclone with a long vortex finder as the separator, a batch sizer was developed for the fast comparative sizing of the coarse solids normally encountered in mineral pulps.Operating times as short as 2 or 3 min gave separations ranging from 16 mesh down to the subsieve sizes.Reproducibility was good and sensitivity was adequate for most applications.

Jan 1, 1968

An oxide ore heap (80,000 ton assaying 2 per cent copper) and a sulphide ore heap (300,000 ton assaying 1·7 per cent copper) are being leached in series in a closed circuit system. The ore is friable and weatherseasily giving severe percolation problems. These were eased by applying liquors at 235 gal/min to trenches 2 ft wide and 6 ft deep along the full length of the heaps.Cementation recovery was improved from 20 per cent to over 80 per cent by regular intermittent agitation of the iron using a back hoe unit.Liquor pH is controlled by acid addition, and iron content is controlled by a bleed-off set according to predictions made from a pH-Eh diagram drawn for the liquor components. These controls, together with acyclic wetting and draining procedure, have raised production from 6 ton/week to 10 tdn/week of 80 per cent copper.

Jan 1, 1968

By Madgwick J. C

The monosaccharides glucose, galactose and arabinose, and the polyols glycerol and mannitol (0.1 Ufo WIV) supported pure and mixed culture heterotrophic bacterial manganese leaching of solid pyrolusite (MnO2, 2% W/V) to yield 14-38 mg/litre manganous ion in 3 days from a simple mineral salts media at 30°C. Supplementation of pure bacterial isolates growing on glucose with soluble intracellular photosynthate from freshwater algae (0.07 g/l carbohydrate) and marine algae (0.11 g/l) led to an improvement in Mn++ yields of 24 and 100 per cent respectively. Extracellular products of the freshwater algae (0.3 g/l carbohydrate) boosted recoveries by 57 per cent.

Jan 1, 1982

By using knowledge-based technology to create a Virtual Mining Enterprise and integrating it with existing technical and financial computer systems, a gold mining company has been able to reduce the time taken to produce a mine plan from 14 weeks to less than one week. Typically, the mine planning process requires circulating and managing large amounts of information. Even with the use of computers in todayÆs business, this is often still a manual process involving file transfers and individualised spreadsheets. Mine planning also involves understanding and managing large quantities of complex and interrelated variables. Added to this is the ever changing dynamics and constraints associated with the business of mining. These issues not only hamper the planning process but also question the validity and usefulness of the mine plans being generated. By integrating the information and knowledge of the numerous departments involved in mine planning into one core Knowledge Base - so called æone version of the truthÆ, - mining companies are able to overcome these pitfalls experienced in traditional planning methods. Once set up, the Knowledge Base creates and runs a virtual mining enterprise with which to visualise and test various scenarios of mining, business and logistical activities. The final output is an optimised enterprise-wide plan with clear and detailed instructions for each of the divisions of the company.

Jan 1, 2000

By R L. Brathwaite

The gold-scheelite-quartz lodes of the Wakamarina valley were the most productive of the mesothermal gold-bearing areas in the Marlborough Schist. Most of the production came from the Empire City and Golden Bar mines which worked the Golden Bar lode. Only 134 m of its 1800 m strike length are accessible, in the No.2 level of the Golden Bar Mine. A fault has downthrown the Golden Bar Mine section by = 47 m and displaced it left-laterally by 18 m. The lode is a typical ribbon-banded mesothermal vein, averaging c. 1.75 m wide, and enclosing narrow horses of schist country rock. It is composed of bands of milky æbuckÆ quartz with thin laminae of schist. Scheelite occurs in short strings of grains within quartz on the footwall side of the lode and also in small quartz-carbonate veinlets in the foot wall and hanging wall schist. The lode quartz contains only localised traces of pyrite and arsenopyrite. They are more abundant in the wall-rock schist.   The Golden Bar lode lies within a steeply dipping normal fault, which, on its footwall side, is adjacent to a 40 m-wide, shallow-dipping mylonite shear zone. Within 1 m of the lode, the shear foliation has been dragged down to nearly parallel the lode footwall. Wall rock alteration is manifested by a marked increase in K and Rb, which correlate with abundant illite/muscovite and K-feldspar within 2 m of the footwall of the lode. Amphibole, stilpnomelane, and pumpellyite show a progressive decrease towards the lode. As and Sb increase close to the lode, but are at background levels within the lode itself. Enhanced Cr (150-430 ppm) in the quartz, relative to the schists (~40 ppm), suggests that the source hydrothermal fluids passed through and leached mafic rocks, such as the metabasites from the hanging wall of the lode (~400 ppm Cr).

Jan 1, 1995

At last year's. annual meeting of The Institute, Sir George Fisher, as President, compared it somewhat nostalgically with a meeting of its kind in the 1920s when comment was expressed on the decline of Australianmining and on the lack of new mineral discoveries.I feel that tonight's annual meeting is even more an occasion for nostalgia, for it represents the seventy-fifth anniversary of the founding of The Australasian Institute of Mining and Metallurgy. I hope, therefore, that I may be allowed to retrace some of the circumstances of this Institute's origin and at the same time to look at some of the broader happenings of those 75 years.From this distance in time it is, of course, much easier to get things in perspective and one of the things that compels enormous admiration in looking back over the history of our Institute is to note the qualities of foresight and keen concern for professional standards which moved the pioneers in this Institute. They had no benefit of hindsight to aid them.Just over 75 years ago, a small group of men met in Broken Hill to discus.s the possibilities of forming an association of mining engineers. The moving spirit was Uriah Dudley, our first secretary, manager of the Umberumberka mine at Silverton. The first formal move to form an association of mining engineers came from the Amalgamated Mining Managers Association of Australasia. At the time, this association was a fairly new group, being 5 years old.It had been formed to try to raise the standard of management throughout the industry. Uriah Dudley and our first provisional president, John Howell, held their first talks in 1891 and further meetings at Broken Hill followed. The inaugural meeting, attended by 200 members, was held in Adelaide in April, 1893.

Jan 1, 1968