Search Documents

By M. G. Nicholas

The influence of deformation, relative movement and surface cleanliness on the strength of room -temperature "interparticle" bonds between copper surfaces has been studied. No bonding resulted when clean surfaces were merely pressed together, even under pressures of 50,000 psi. Bonding resulted, however, when clean surfaces were simultaneously pressed and moved relative to each other, some bonding occurring no matter how small the pressure or relative movement. Exposure of the clean surfaces to various chemicals inhibited bonding, none at all being produced by small relative movements. The size of the movements which first produce bonding between exposed surfaces depends on the nature of the chemical, being less than 0.002 in. for cleansing reagents and greater than 0.004 in. for lubricants, water and hydrogen sulfide. It is concluded from the experimental data that the prime requirement for bonding is the dispersal of surface films such as oxides and adsorbed contaminants. THE formation of interparticle bonds during the room-temperature compaction of powder metallurgy components greatly increases the ease of handling in subsequent production operations prior to sintering. The strength of unsintered compacts follows the same general trends as their density and hardness, but quantitative data are extremely Scarce. Quantitative correlation of the data on the overall strength of a compact with that of the individual interparticle bonds is virtually impossible due to the extremely complex geometry of powder compacts. Qualitatively, however, the strengths of unsintered compacts can be correlated with variations in parameters known to influence the extent of cold bonding, and hence interparticle bonding, such as surface cleanliness, relative movement, and deformation of the mating surfaces. Kuzmic and seelig4 found that contamination of powder particle surfaces with lubricants reduced the strength of unsintered iron and copper compacts. Interparticle shear has been shown to promote bonding by Train and Hersey7 while Gregory has shown that die rotation is beneficial. Eilender and schwalbe6 concluded that most bonding occurred during the early stages of pressing iron powder compacts when interparticle shear is one of the principal processes occurring. mile there can be little doubt that these and other factors, such as particle size and shape, affect the extent of interparticle bonding produced by compaction, evaluation of the influence of individual factors is not easy. Particle deformation and relative movement, for example, occur simultaneously during compaction, making any precise measurement of their relative influences difficult. Because of these and other difficulties encountered in studying interparticle bonding in actual powder compacts, the approach adopted in this study was to

Jan 1, 1963

By F. Peter

I. GENERAL INTRODUCTION. TECHNICAL progress takes place in two directions: the improvement of methods, affecting the quality of the product; and increase in the economy of operations, affecting its cost. In the iron-industry, practice is pretty well settled, and. revolutionary changes of method are, for the present, not to be expected. Hence, in this industry, the principal endeavor is to reduce costs by the use of labor-saving inventions, such as the machines brought into use during the last decade. But it is not alone necessary to reduce the labor-cost; complete economy requires also a saving in raw material. Under this head we may rank the coal employed as metallurgical fuel; and it follows that progress includes the economic use of fuel, so managed as not to injure quality of product. In the present paper it will be shown how, by suitable utilization of the heat from the furnace, a large portion of it may be made available for other purposes. Such utilization of waste-gases is important in all industries which employ furnaces (especially heating- and smelting-furnaces); and in the first rank of these stand the iron-, glass-, and porcelain-manufactures. The following pages are devoted chiefly to the waste-gases of smelting-works, and especially to those reverberatory-furnace gases which are not combustible.'

Jan 12, 1913

By Hertha R. Freche

The diffusion of magnesium and silicon from the core into the high-purity coating of Alclad sheet is important commercially, and led to the use of a duplex product for the study of diffusion by means of spectro-graphic analysis of successive layers. It has been found that in the duplex materials the diffusion of magncsium from an undersaturated aluminum-magnesium alloy into its high-purity aluminum coating is approximately of the same order of magnitude as the diffusion of silicon from a saturated aluminum-silicon alloy into its high-purity aluminum coating. However, if magnesium and silicon are both present in the alloy in the ratio of Mg2Si, they appear to diffuse in the approximate ratio of this compound. Finally, if the alloy contains silicon in excess of the amount required by magnesium silicide, the amount of diffused silicon in the high-purity aluminum coating will also be in excess. The interdiffusion of metals in the solid state is of both scientific and technical interest, because it is helpful in the study of the alloy structure and in the solution of problems pertaining to the strength and surface condition of the fabricated product. W. C. Roberts-Austenlt carried out the first quantitative determination of the coefficient of diffusion of gold into lead. This classical experiment was followed by a series of investigations on the diffusion of metals and nonmetals in iron and steel and in nonferrous metals and alloys. Recently the diffusion of copper in coated strong aluminum alloys was investigated by A. Burkhardt2. This appeared to be the first published investigation on the diffusion of metals into aluminum. The present investigation was the direct result of a technical question in connection with alloy fabrication and is a summary of some preliminary work pertaining to the diffusion of magnesium and silicon into aluminum. The results necessarily will be subject to some variations, since this is the first attempt to evaluate the coefficients of diffusion of magnesium and silicon into aluminum according to this method of procedure. This

Jan 1, 1936

By T. R. Scott

The acid pressure leaching of zinc-lead flotation concentrates from the McArthur River deposit, Northern Territory, Australia, has been studied in a three-stage, continuous, co-current system, using titanium reactors of 6 gal capacity. The starting pulp contained 2.7 lb solids per gal of synthetic spent electrolyte and the final liquors contained 120-125 gpl Zn. Parameters investigated included temperature (95-120°C), oxygen pressure (30-100 psi), acid addition (80-130% of theoretical), and leaching time (35-65 min per stage). Technical factors studied included mixing and pumping of feed, agitation, settling and washing and control mechanisms. The chemistry of liquor impurities, of scale formation in autoclaves and of lead jarosites in residues was studied in some detail. Results indicated that 90-93% zinc recovery could be obtained with a "low- acid" process, using 113°C and 70 psig with oxygen as the favored operating conditions. Residues contained 16-18% elemental sulphur and 15% lead, together with unreacted pyrite and gangue minerals. Pelletizing of residues was impracticable, and alternative suggestions for the recovery of lead, sulphur and silver are discussed. Preliminary estimates for plant and operating costs are given and enable some comparison to be made with conventional procedures.

Jan 1, 1973

By R. R. Unterberger

Three different physical techniques have been used to see through or probe into rocks, so miners might know what is ahead or overhead. These are radar, sonar, and a unique type of sonar called nonlinear sonar. Five radar systems have been developed. The highest frequency used is 4300 MHz for detecting small fractures at close range. This gives the best resolution. For longest range (over 2000 m, or 6560 ft) we use the 30 MHz radar for finding faults ahead of mining or ranging to salt dome flanks. Two types of salt, dome and bedded, are recognized. Radar works well in dry (dome) salt, but not in bedded salt which contains small amounts of water. The dipole moment of water absorbs energy from the radar. Thus was born the 30 MHz radar system and sonar probing systems. These can probe to 100 m (328 ft) even into wet salt. All probing systems measure data in time, which are converted to distance by measuring the time of travel of radar or sonar through salt pillars of known thickness. Ranges of probing in salt are from less than 1 m (3.3 ft) to more than 2000 m (6560 ft). Uses of radar and sonar probing in mines include mapping the top of salt above a mine; mapping salt dome flanks; finding impurities in salt such as anhydrite, sandstone, or potash stringers; locating old boreholes in salt pillars; locating fractures in salt; and finding faults or water zones ahead of mining.

Jan 1, 1985

By A. W. Ambrose

THE underground losses of oil exceed by hundreds of thousands of barrels all the oil that has been lost in storage, transportation, or refining. The quantity lost is, of course, indeterminate; but when it is considered that the contents of an entire oil field have been excluded from recovery by invading waters, some idea of the amount wasted may be gained. Similarly, enormous quantities of gas have been lost underground. Conservation of the oil, therefore, should start before it is brought to the surface rather than after it is placed in storage tanks. Water is one of the most important causes for underground losses and the operator should give as serious consideration to an underground flood of water as he would to a destructive surface flood. The best insurance, of course, is to have the wells drilled in such a manner that water has no access to the productive oil and gas horizons, and on abandonment the wells should be properly plugged. The encroachment of edge water and the occurrence of water in the base of an oil sand present a very serious problem to an oil company; sooner or later these waters are bound to cause considerable damage, if they do not entirely destroy the possibilities of further production. Too often, however, a field has been considered to be in a hopeless condition, whereas wells in as bad a condition in other areas have been repaired and the life of the field appreciably lengthened. The corrections are very often suggested by technical study. Very successful results have been accomplished by detailed underground work in the California oil fields, in Cushing, Oklahoma, and in other areas.

Jan 9, 1920

By Fred C. Bond

AN improved method of measuring the surface area of a comminution product down to any desired particle size has been developed. The method is largely graphical, and requires relatively little calculation. It can be used with materials containing large amounts of clay, or excess fines of any kind. The surface area S is expressed in terms of square meters per100 c.c. of solids. This expression is based upon volume rather than weight, and is considered to be more suitable for crushing and grinding problems, where the machines ordinarily are operated under constant volume conditions. It has the advantage that surface areas of different materials can be compared directly, even though their specific gravities may be unknown. The "specific surface" of a material, or the number of square centimeters of surface area per gram, is equal to 100S divided by the specific gravity. Particle diameters are expressed in microns, K being the diameter of the largest particle present and L the grind limit, or lower size limit of the particles formed directly by grinding. The value of K does not always coincide exactly with the diameters of the largest particles retained on the coarsest testing sieve, since the largest particles formed in crushing and grinding are often slabby, or have other irregular shapes. L has been chosen as 0.700 microns, or number 27.5 in the size number series,1 for reasons to be explained later. S is the total surface area of all particles larger than L microns in diameter. When a homogeneous comminution product is separated into fractions whose diameters bear a constant geometrical relationship [p] to each other, and the log per cent weight retained upon each size and passing the next larger size is plotted against the log diameter, a straight line results, which is called the distribution line, and which has a slope in called the distribution modulus. The distribution line can be extended to any desired limiting size, and the total surface area of all particles larger than that size can be calculated. The equation of the distribution line is w = Cxm [I] where w is the per cent weight retained on each successive sieve; x is the particle diameter; and C is the per cent weight retained on an opening of unit diameter.2 Theoretically, the distribution line can be extended to include infinitely small particles. When it is so extended, and the assumption is made that no fine particles are present other than those accounted for by the equation; the log per cent cumulative weight passing any series of sizes, plotted against the log diameter passed, will result in a straight line lying parallel to and above the plotted distribution line.

Jan 1, 1941

By W. H. Emmons

MANY mineral veins occupy faults, and movements on certain warped fault planes have resulted in openings. On normal faults the [ ] steeper parts have the widest openings, and on reverse faults the flatter parts have the widest openings. Theoretically the width of the opening is the sine of the angle of deflection times the amount of movement on the fault plane, but actually the widths of some of the openings are probably less because of readjustments of walls along joints or of other readjustments. The first treatment of the subject seems to have been in a book on mineral veins by John Leithart, published in Newcastle, England, in 1838. Later the subject was treated in various texts published in Germany, in England, and elsewhere. The subject was not given much prominence in the earlier American literature on economic geology, but has interested several workers in that field in the past decade. In this paper examples of districts showing ore shoots on warped faults, with relations noted, are described. Fault veins of the three depth classes of veins are noted. Many epithermal veins are in normal faults, and commonly the larger ore shoots are in their steeper portions. Many mesothermal veins are in reverse faults and many others are in normal faults. The flatter parts of veins in reverse faults are commonly wider than the steeper parts, although they are not always as rich as the steeper segments of the veins. There are not many hypothermal veins in faults of measured displacement.

Jan 1, 1943

By G. F. Jenkins

ASBESTOS is a general term embracing the fibrous varieties of a number of minerals. Of these, the hydrous magnesium silicate, chrysotile (H4Mg3Si209), a variety of serpentine, is the most abundant and useful to industry. All other types of asbestos belong to the amphibole group of minerals and are classified as: crocidolite, NaFe(SiO3), FeSiO3; anthophyllite, (MgFe)SiO3; amosite, also a ferromagnesium silicate but with iron content higher than that of anthophyllite; tremolite, CaMg3(SiO3)4; and, actinolite, Ca (MgFe)3(SiO3)4. PROPERTIES The commercial value of asbestos depends largely on the physical property that permits it to be readily separated into fine filaments of high tensile strength and flexibility, which, coupled with the fact that it has the quality of incombustibility of a mineral-in distinction to vegetable and animal fibers-makes it of unique usefulness for many purposes. To some extent, the value depends upon the length of the fiber, although extreme length is neither necessary nor desirable for most purposes. Chrysotile occurs as cross-fiber veins, in which the asbestos fibers are approximately' at right angles to the vein walls, with vein width- or fiber length-seldom exceeding 2 or 3 in.; also as slip-fiber, in which the fibers 'lie in the same plane as the vein or on slippage planes. A cleanly broken vein of cross-fiber has a pearly luster and may range from a deep green or brown color to light shades of yellowish green or cream. When of good quality, the fiber filaments forming the vein may be easily drawn away from their neighbors and exhibit a fine silkiness and pure white color. They may be twisted into a thread and when flexed between thumb and fingers are found to be strong and pliable. Chrysotile withstands comparatively high temperatures without breaking down completely or fusing but begins to lose water of crystalliza-

Jan 1, 1949

By C. B. Alcock, M. G. Hocking

The kinetics of the growth of sulfate layers on blocks of Cu20 has been studied between 688" and 800°C. At 788c the over-all weight increases followed the parabolic rate law, with k = 216 30 sq mg per cm4 min, using a 1:1 entering gas mixture of SO2:02. At 757 after an initial linear period the parabolic rate law was followed, with k = 57.8 10 sq mg per cm4 min. The gas mixture required a platinum catalyst to produce the maximum SOs pressure. The sulfation rate at 757' and 788c was high until all the CUZO had changed into a core of CuO, when it became very much lower. At 757°C marker experiments showed that the sulfates (CuO. CuS04 and CuSO4) grow outwards from the oxide surface, but CuO. CuS04 mixed with CuO was found beneath the markers. At 688 markers were found at the CuO. CuS04/CuS04 interface. Visual observations at 757 showed a liquid eutectic moving beneath the sulfate surface. causing very rapid sulfation and extruding to solidify as thick 'needles" up to 8 mm long. Marker experiments have shown conclusi.cely that CuO grows on Cu20 in air by the outward migration of copper. ThermODYNAMIC measurements on the sulfate and basic sulfate of copper, reported recently,' are followed here by measurements of the rates of formation of these sulfates on cuprous oxide, in order to provide a background for the understanding of roasting processes. peretti2 and McCabe and Morgan3 have shown that the phase Cu20 lies next to Cu2S when the sulfide is roasted under conditions where sulfates will be formed. Since this would present too complex a system for kinetic study, the present work4 has been based on the kinetics of sulfation of the oxide phase. The results of a study of the kinetics and mechanism of the sulfation of cobaltous oxide have recently been reported.4,5 Results on the sulfation of cuprous oxide have also appeared,6 but are at variance with those to be reported here. This seems to be because the previous workers6 did not obtain constant SO3 pressures from the SO2/O2 sulfating gas mixtures used, as will be discussed later. Wadsworth, Leiter, Porter, and Lewis found that the sulfates produced when SO2/O2 mixtures are passed over Cu20 at red heats are CuS04 and the basic sulfate CuO.CuSO4. When the decomposition of CuS04 was followed' by differential thermal analysis, a stage corresponding to CuO .CuS04 was reached before decomposition into the oxide occurred. APPARATUS The vertical furnace used for quantitative studies was a conventional resistance-heated and propor- tionately controlled furnace with an even zone (1 deg) which was 4 cm long. The gas mixtures of SO2 and 02 were made by mixing measured flows from capillary flowmeters and drying over phosphorous pentoxide before passing them into the Pyrex top-piece of the furnace assembly. A mullite tube of bore 2% cm was used as reaction vessel and at the bottom of this tube was a trap for SO3, which condensed as a colorless liquid. The residual gas was led into a fume cupboard for ventilation to the atmosphere. The furnace used for visual observations of needle growth and other phenomena consisted of a transparent silica reaction tube of bore 3 cm, having an optically flat silica window sealed into its wall. The reaction tube was clamped vertically, inside a mullite tube of bore 4 cm and length 42 cm which was heated by Kanthal windings. The window in the silica reaction tube was arranged opposite a hole 3 cm wide and 2 cm tall which had been cut in the wall of the mullite winding tube 19 cm from its top end. A binocular microscope was used to look through the window, illumination being provided by a focusing microscope-lamp offset sideways and downwards. The oxide block to be sulfated was suspended from the removable Pyrex top-piece to the reaction tube, by means of which it was inserted at the start of the experiment, and through which entered the S02/02 gas mixture. The variation of the temperature inside the reaction tube with horizontal and vertical displacement from the window was investigated, and, while it can be said that the temperature was constant 1 deg, its value at a given position was known only to 12 deg. In both furnaces, the oxide block to be sulfated was suspended from a small silica hook immediately downstream from a platinum thimble used as catalyst, which was held on a long silica rod from a Pyrex spring attached to the removable Pyrex top-piece of the furnace. The spring was only included in the quantitative sulfating furnace; its sensitivity was 1.4 cm per g and it was found to be free from creep in a 16-hr test when carrying the working load. The extensions were followed by a cathetometer which could be read to 0.001 cm, corresponding to i0.7 mg. Extensions of the spring were measured on adding weights between 5 and 500 mg to the working load (thimble + oxide block), and Hooke's law was closely obeyed. SAMPLES Cuprous oxide blocks were prepared by oxidizing Johnson Matthey "Specpure" copper sheet of 1 mm thickness (impurities: iron at 3 ppm, silver at 2 ppm, lead, nickel, sodium, and silicon each at 1 ppm, calcium, chromium, magnesium, and manganese each at less than 1 ppm) for 6 days in air at 1000°C in a re-crystallized alumina boat. It has been reported7 that when Cu20 is prepared by heating copper sheet for 1 day the central plane of the blocks produced consists

Jan 1, 1967

By Paul M. Tyler

Higher freight rates and better methods of beneficiation now may make it more economical to open inferior deposits closer to a glass factory than to work higher-grade deposits farther away. Nature of impurities and special treatments as well as common practice of sulphuric acid leaching are described. HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for substandard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade silica sand are abundant, but most of the best deposits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.O.b. cost of mining and treatment may be much higher than at a higher grade deposit farther away. Particle-size distribution is a feature of glass-sand specifications. As long as glassmakers insisted upon having their sand principally coarser than 100-mesh, any material was automatically excluded from consideration that could not be purified without fine grinding or other drastic treatment which greatly reduces the size of the quartz grains. However, re- cent large-scale tests in Norway' showed that finely-crushed quartz used in a soda-lime-silica glass batch caused it to melt and become refined appreciably faster than when ordinary coarse (Belgian) sand was employed. Dust losses were negligible. Since the pre-war cost of sand was only 3 pct of the manufacturing cost of the glass, it was deemed economical to pay twice as much for crushed quartz because of the saving in wear and tear on the furnace walls. In the author's unverified opinion, sand ranging in size between 150 and 400-mesh would probably be superior to that in the more usual range of 20 to 100-mesh. Former objections to fine sand (other than dust) were doubtless fostered by the natural concentration of impurities in the finer sizes. Ordinarily the most objectionable, as well as the commonest, impurity from the standpoint of the manufacturer of any but the cheaper qualities of colored glass is iron. No natural sands are really pure silica. Even water-clear quartz crystals are likely to contain impurities in the form of solid solution as well as inclusions which cannot be eliminated except by chemical treatment that will break down the silica lattice. Pure white pegmatite quartz will usually analyze 0.01 pct or more of iron oxide, and ordinary vein quartz and the quartz grains in most

Jan 1, 1951

By R. H. B. Jones

This paper reviews pertinent geology of the Biwabik iron formation, Mesabi Range, Minnesota. This iron formation is divisible into four members. Each member is distinctive and contains marker horizons, which are recog nizable throughout all phases of alteration from lean, fresh rock to high-grade iron ore. Some beds have a larger magnetite content than others. During the process of ore genesis, which is essentially an oxidation process, the magnetite content is lowered. Alteration from iron formation to ore includes both oxidation of iron minerals and silica removal by leaching and these distinct processes progress at variable rates for different locations and structures. Magnetic intensities, of each horizon of the iron formation are dependent chiefly upon its preoxidation magnetite content, upon the subsequent degree of oxidation, upon the character of the enclosing rocks, and on the extent of fracturing, folding, or faulting. The results of a number of magnetic surveys are described and are correlated with results of drill-hole and mine exploration and developmerit. The magnetic anomalies obtained are discussed in relation to phases of formation of ore within the iron formation. General Information One hundred years ago a party of surveyors, applying the principles of geophysical prospecting, discovered iron ore in the state of Michigan in the Lake Superior district. This event was officially reported as follows:' On Sept. 19 (1844) while running the east line of Town 47 North, Range 27 West, they observed by means of the solar compass remarkable variations in the direction of the needle, amounting to 87" from the normal. Ascribing this phenomenon to iron ore, they sought and found it in ledges or outcrops at several points. The solar compass referred to was invented by William A. Burt, deputy surveyor in charge of this party.2 It is used for determining the true meridian by an observation on the sun. Eight years later, on July 7, 1852, the first iron 're, consisting of 6 bbl. of Ore, was shipped from Marquette, Michigan. It was another 40 years before the first or> shipment left the Mesabi Range in Minnesota, in October 1892. It totaled 4245 tons. Fifty years later, 90 years after the original shipment, during 1942 the Lake Superior district shipped 93,495,392 gross tons of iron ore. Production came from Minnesota, Michigan, Wisconsin, and Ontario, Canada. Throughout the 90-Year period it was known that magnetic properties of most of the ore bodies, and of the iron formations in which they occur, affected the compass. This phenomenon, later to be made use of to outline areas of ground favorable for exploration, was at first a

Jan 1, 1949

By Roland D. Parks

Corundum, little publicized as an industrial abrasive, has, in its small way, contributed greatly to the production of many specialized items vital to our war program and to Our allies. Optical elements Of the highest quality for range finders, bombsights, and scientific instruments; precision metal parts for torpedoes and airplane engines; quartz crystal plates for military radios; armorplate and malleable castings for tanks and guns; and eyeglasses for everyone; these are some Of the products that corundum has helped to produce in the quantities needed and on time. Unlike metals and many other raw materials, corundum is not incorporated into any Of these finished products. It is simply a grinding medium used to produce the desired finish or precision; an operating supply or tool, so to speak. With a Mobs' scale index of 9, corundum ranks next to the diamond in hardness among the natural minerals and is superior to emery and garnet. The gem varieties of corundum, including the Oriental ruby and sapphire, are frequently more highly prized as jewels than the diamond. It is the intent Of this paper to deal Only with a description of the corundum industry, the administration of wartime control, and certain economic aspects as seen by the author. Several references are listed to assist anyone who wishes further information on the geological occurrence of the mineral. Ore Production and Consumption For the past two decades, south Africa has been the world's sole producer of corundum ore. A possible exception is Russia, where, it is understood, there was considerable production during the thirties for domestic consumption but for which statistics are lacking. The United States is the world's principal consumer of corundum ore; imports lor the period 1934 through 1940 averaging 3000 Short tons per year, The years 1935 and 1936 were close to the 5000-ton mark, and imports during 1941, the last prewar year for which statistics have been released, were approximately 6000 Short tons. Again lacking statistics on Russia, the United Kingdom ranks second, but far below the United States in consumption of ore. Historically, corundum has been found in some 35 countries throughout the world, but the principal deposits are in South Africa, Canada, Madagascar, Russia and the united States. Deposits are generally small and subject to rapid exhaustion. Thus, the United States was the principal world producer for the period 1870 to 1900, when operations ceased except for two years during World War I. India was a producer of ore from 1898 through 1921, with peak output in 1916 through 1918 Canada came into production in 1901 with substantial output of ore and finished grain until 1914; the production thereafter was smaller until 1921. Madagascar has produced ore since 1910 but has had important output in only a few scattered years. South African production started in 1912

Jan 1, 1948

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

By E. C. Wright

The following article is based on observation of college graduates entering the steel industry in technical work made during the Past 25 Years, the first five of which were spent as a college instructor in two engineering schools, and the last 20 in the employ of a large steel company that has hired hundreds of engineering graduates for steel-mill operations. The college graduates encountered during this period have come from many colleges representing schools in Eastern States, Midwestern Universities, many Southern colleges, and many smaller colleges and normal training schools mostly in western Pennsylvania and Ohio. The college training of these students for engineering work naturally has varied widely and the educational qualifications of the entrants have been in many ways different. It was found at an early date that graduates of standard engineering colleges were much more adaptable than graduates in science from nontechnical schools. The engineering students seemed to be more suited to actual work in steel plants and in general were better able to grasp a knowledge of the operations they observed. However, although the graduates of engineering schools have had somewhat better training in physics, mathematics, and engineering, it has been a general and continual observation that most of the students employed have had inadequate training in the fundamental sciences. Since this discussion relates entirely to metallurgical engineers it should be emphasized that students taking metallurgical engineering courses in college seem to be poorly trained in organic chemistry-physics, physical chemistry, thermodynamics, and any higher form of mathematics than simple calculus. It has been noted frequently that young engineers faced with problems in a mill that involve some mathematics generally flounder badly, and that they have little conception of physical chemistry. Another common deficiency lies in the young graduate's lack of knowledge of where to look for the more detailed literature on any subject. He reverts instinctively to some college textbook whose coverage is usually very elementary. It is recommended that such textbooks contain a bibliography of the source literature. and that students be taught to use the original data. Many of the students had had previous courses in college dealing with metallurgical work such as steel melting, metallograhy, etc.r but it was found that their grasp of these subjects was extremely sketchy. It was soon realized that an ordinary engineering graduate could be taught more about steel melting and manufacturing processes in a few weeks in a plant than he could learn in a college course on such subjects. A similar statement may be made regarding the ability of students to conduct laboratory work. Their lack of technique and skill in handling equipment and setting up experiments was soon apparent. It became neces-

Jan 1, 1948

By R. J. Wasilewski

THERMAL expansion of rhenium data have been reported by Agte et al.,&apos; and Medoff and cadoff,&apos; respectively, while the linear expansion coefficient was determined by Sims et Al.3 Denoting expansion coefficients parallel and at right angle to c axis by all and Al respectively, their weighted mean should be equal to dilatometric linear coefficient of a random polycrystalline specimen. The values reported for these coefficients are tabulated below: Since these values are in poor agreement, and because of anomalous expansion behavior observed in titanium 4 and chromium, a rede termination of the axial expansion was carried out. A Unicam 19-cm-diam high-temperature camera was used, with unfiltered CuK radiation. Camera calibration was carried out using at Pt wire standarde at temperatures up to 1100oC, the variation between indicated and true temperature being within the experimental error (estimated at <3oC) above 750o C. Rhenium Johnson Matthey spectrographic standard) was vacuum annealed at 1000 oC prior to X-ray diffraction experiments. Lattice parameters were obtained by least-squares solution using the reflec- tions (1232), (1015), (2024), and (3030) for all the patterns, and the additional reflection (2133) for higher temperature (400°C and above) patterns. The relative expansion data obtained are shown in Fig. 1, lengths of the vertical bars indicating the spread in the parameter values obtained by using various combinations of three spacings from the four or five measured. The data calculated from the equation of Ref. 2 are included for comparison purposes. Several specimens were used to obtain the above data, neither of them showing a significant parameter change after completion of the high temperature runs. Some parameter data and the corresponding expansion coefficients between 25 oC and the measurement temperature are tabulated below. The comparison of the present data with those previously reported shows reasonable agreement with the results of Medoff and cadoff2 within the temperature range covered by them (up to 1000 oC). The a values are appreciably higher throughout most of the investigated temperature range. The basal expansion is—in agreement with their findings—appreciably higher than that in the direction of hexagonal axis. The expansion coefficient, al, however, decreases rather more slowly with temperature than previously reported. The expansion along the c axis up to nearly 1000°C appears in excellent agreement. However, at higher temperatures there is a marked deviation towards higher expansion, reproducible between different specimens. Furthermore, there seems to be some irregularity in the variation of all with temperature, the apparent local minimum and maximum values at 510o and 1024o C, Table II, being well outside the experimental error limits. It must be stressed that the apparent discontinuity in the c parameter expansion is still insufficient to account for the expansion value reported by Agte et al.&apos; since a total expansion of close to 2 pct would

Jan 1, 1962

By E. C. Wright

The following article is based on observation of college graduates entering the steel industry in technical work made during the Past 25 Years, the first five of which were spent as a college instructor in two engineering schools, and the last 20 in the employ of a large steel company that has hired hundreds of engineering graduates for steel-mill operations. The college graduates encountered during this period have come from many colleges representing schools in Eastern States, Midwestern Universities, many Southern colleges, and many smaller colleges and normal training schools mostly in western Pennsylvania and Ohio. The college training of these students for engineering work naturally has varied widely and the educational qualifications of the entrants have been in many ways different. It was found at an early date that graduates of standard engineering colleges were much more adaptable than graduates in science from nontechnical schools. The engineering students seemed to be more suited to actual work in steel plants and in general were better able to grasp a knowledge of the operations they observed. However, although the graduates of engineering schools have had somewhat better training in physics, mathematics, and engineering, it has been a general and continual observation that most of the students employed have had inadequate training in the fundamental sciences. Since this discussion relates entirely to metallurgical engineers it should be emphasized that students taking metallurgical engineering courses in college seem to be poorly trained in organic chemistry-physics, physical chemistry, thermodynamics, and any higher form of mathematics than simple calculus. It has been noted frequently that young engineers faced with problems in a mill that involve some mathematics generally flounder badly, and that they have little conception of physical chemistry. Another common deficiency lies in the young graduate&apos;s lack of knowledge of where to look for the more detailed literature on any subject. He reverts instinctively to some college textbook whose coverage is usually very elementary. It is recommended that such textbooks contain a bibliography of the source literature. and that students be taught to use the original data. Many of the students had had previous courses in college dealing with metallurgical work such as steel melting, metallograhy, etc.r but it was found that their grasp of these subjects was extremely sketchy. It was soon realized that an ordinary engineering graduate could be taught more about steel melting and manufacturing processes in a few weeks in a plant than he could learn in a college course on such subjects. A similar statement may be made regarding the ability of students to conduct laboratory work. Their lack of technique and skill in handling equipment and setting up experiments was soon apparent. It became neces-

Jan 1, 1948

By John J. McCabe

INTRODUCTION Over the years, Congress has written into the Internal Revenue Code various provisions aimed at lessening at least one financial burden faced by taxpayers in the mining industry - the federal income tax burden. These provisions include the election to deduct exploration expenses, the election to defer deduction of development expenses, and the percentage depletion deduction. Careful tax planning from the very beginning of a mining venture is essential in taking maximum advantage of these tax benefits. A major decision to be made is the choice of organizational structure. (For a more detailed discussion of this subject, see McCabe, John J., "Developing Structures for Investments in Mineral Property," New York University Institute on Federal Taxation, 42 NYU 24, 1984). One such structure is the use of multiple corporations, with mining activities conducted by one corporation and nonmining activities, such as manufacturing, financing and administration, conducted by the other corporation. This technique, which will be discussed in detail below, can be particularly advantageous in delaying recapture of previously deducted exploration expenses and in maximizing depletion deductions. TAX BENEFITS IN MINING Exploration Subject to certain restrictions discussed below, exploration expenditures (i.e., expenditures paid or incurred during the taxable year for the purpose of ascertaining the existence, location, extent, or quality of any deposit of ore or other mineral, and paid or incurred before the beginning of the development state of the mine are deductible at the election of the taxpayer (Section 617(a)).* Were it not for this option, exploration expenditures would be required to be capitalized and recovered through depletion, after production begins. Exploration of a mineral deposit can be very costly and may not result in commercial production for some time. If the taxpayer has income to he offset by the deductions, a mining venture can usually be structured in such a way as to allow the offset of mining losses against the other income. With today&apos;s high interest rates, this election can be quite valuable in present value terms. Corporate and noncorporate taxpayers are subject to different restrictions on this tax benefit. Corporations may elect to deduct only 85 percent of eligible exploration expenditures (Section 291(b)). (The Tax Reform Act of 1984 reduced this to 80 percent effective for expenditures after December 31, 1984, in taxable years ending after such date). The remaining 15 percent (20 percent after December 31, 1984) is capitalized and recovered at the same rate as five-year ACRS property (Section 291(b)). Individual taxpayers are not subject to this 85 percent rule; however, any amount deducted in excess of ten-year straightline amortization is a tax preference item for individuals (Section 57(a)(5)). Individuals may avoid the tax preference by electing to capitalize exploration expenditures and amortize them over ten years (Section 58(i)). In order to prevent the taxpayer from, in effect, converting ordinary income into capital gain by selling property that has given rise to exploration expense deductions, the Code requires recapture of such deductions upon the occurrence of certain events (Section 617): 1. Upon disposition of the property, adjusted exploration expenditures are recaptured to the extent of gain realized on the disposition (Section 617(d)). 2. If the property is leased, the lessor is disallowed any depletion deduction until his adjusted exploration expenditures have been recaptured in the form of foregone depletion deductions (Section 617(c)).

Jan 1, 1985

By Roland D. Parks

Corundum, little publicized as an industrial abrasive, has, in its small way, contributed greatly to the production of many specialized items vital to our war program and to Our allies. Optical elements Of the highest quality for range finders, bombsights, and scientific instruments; precision metal parts for torpedoes and airplane engines; quartz crystal plates for military radios; armorplate and malleable castings for tanks and guns; and eyeglasses for everyone; these are some Of the products that corundum has helped to produce in the quantities needed and on time. Unlike metals and many other raw materials, corundum is not incorporated into any Of these finished products. It is simply a grinding medium used to produce the desired finish or precision; an operating supply or tool, so to speak. With a Mobs&apos; scale index of 9, corundum ranks next to the diamond in hardness among the natural minerals and is superior to emery and garnet. The gem varieties of corundum, including the Oriental ruby and sapphire, are frequently more highly prized as jewels than the diamond. It is the intent Of this paper to deal Only with a description of the corundum industry, the administration of wartime control, and certain economic aspects as seen by the author. Several references are listed to assist anyone who wishes further information on the geological occurrence of the mineral. Ore Production and Consumption For the past two decades, south Africa has been the world&apos;s sole producer of corundum ore. A possible exception is Russia, where, it is understood, there was considerable production during the thirties for domestic consumption but for which statistics are lacking. The United States is the world&apos;s principal consumer of corundum ore; imports lor the period 1934 through 1940 averaging 3000 Short tons per year, The years 1935 and 1936 were close to the 5000-ton mark, and imports during 1941, the last prewar year for which statistics have been released, were approximately 6000 Short tons. Again lacking statistics on Russia, the United Kingdom ranks second, but far below the United States in consumption of ore. Historically, corundum has been found in some 35 countries throughout the world, but the principal deposits are in South Africa, Canada, Madagascar, Russia and the united States. Deposits are generally small and subject to rapid exhaustion. Thus, the United States was the principal world producer for the period 1870 to 1900, when operations ceased except for two years during World War I. India was a producer of ore from 1898 through 1921, with peak output in 1916 through 1918 Canada came into production in 1901 with substantial output of ore and finished grain until 1914; the production thereafter was smaller until 1921. Madagascar has produced ore since 1910 but has had important output in only a few scattered years. South African production started in 1912

Jan 1, 1948

By R. H. B. Jones

This paper reviews pertinent geology of the Biwabik iron formation, Mesabi Range, Minnesota. This iron formation is divisible into four members. Each member is distinctive and contains marker horizons, which are recog nizable throughout all phases of alteration from lean, fresh rock to high-grade iron ore. Some beds have a larger magnetite content than others. During the process of ore genesis, which is essentially an oxidation process, the magnetite content is lowered. Alteration from iron formation to ore includes both oxidation of iron minerals and silica removal by leaching and these distinct processes progress at variable rates for different locations and structures. Magnetic intensities, of each horizon of the iron formation are dependent chiefly upon its preoxidation magnetite content, upon the subsequent degree of oxidation, upon the character of the enclosing rocks, and on the extent of fracturing, folding, or faulting. The results of a number of magnetic surveys are described and are correlated with results of drill-hole and mine exploration and developmerit. The magnetic anomalies obtained are discussed in relation to phases of formation of ore within the iron formation. General Information One hundred years ago a party of surveyors, applying the principles of geophysical prospecting, discovered iron ore in the state of Michigan in the Lake Superior district. This event was officially reported as follows:&apos; On Sept. 19 (1844) while running the east line of Town 47 North, Range 27 West, they observed by means of the solar compass remarkable variations in the direction of the needle, amounting to 87" from the normal. Ascribing this phenomenon to iron ore, they sought and found it in ledges or outcrops at several points. The solar compass referred to was invented by William A. Burt, deputy surveyor in charge of this party.2 It is used for determining the true meridian by an observation on the sun. Eight years later, on July 7, 1852, the first iron &apos;re, consisting of 6 bbl. of Ore, was shipped from Marquette, Michigan. It was another 40 years before the first or> shipment left the Mesabi Range in Minnesota, in October 1892. It totaled 4245 tons. Fifty years later, 90 years after the original shipment, during 1942 the Lake Superior district shipped 93,495,392 gross tons of iron ore. Production came from Minnesota, Michigan, Wisconsin, and Ontario, Canada. Throughout the 90-Year period it was known that magnetic properties of most of the ore bodies, and of the iron formations in which they occur, affected the compass. This phenomenon, later to be made use of to outline areas of ground favorable for exploration, was at first a

Jan 1, 1949